IMC Networks 852-16440, 852-16443, 852-16441, 852-16442, 852-16444 Features And Benefits

CONVERSION

PD-Switch

PoE-Powered, Network-Extending 10/100Base-T Multi-Port Switch

PD-Switch combines flexible copper and fiber interface options with
port and packet-based traffic prioritization while extending network
range by utilizing Power over Ethernet (PoE) technology

Features and Benefits

10/100Base-T multi-port switch
powered by IEEE 802.3af Power Over
Ethernet

PD accepts power from any network •
device providing PoE

Multiple ports increase network port •
density

Meets a multitude of installation
requirements

SFP and fiber port configurations •
(optional) for different network
environments
1X9 fiber port is fixed at 100 Mbps•
SFP port speed is SFP dependent •
All RJ-45 ports feature Auto-Cross and •
Auto-Negotiation
Port for High Priority traffic •
Available with ST or SC fiber •
connectors
Optional single-strand fiber model•

Full-Featured Switch

Broadcast Storm Protection helps •
control excessive broadcast traffic
DiffServ on all ports provides quality of •
service prioritization
Far End Fault provides notification of •
Link Loss on all fiber ports
One High-Priority Port•
Supports 1,916 byte Packet Size•

The (PoE) PD-Switch is a full-featured, 5-port 10/100Base-T MAC
layer switch that extends the range of Ethernet networks, and
increases port density, while being powered via IEEE 802.3af­compliant PoE through its "PD-port" (eliminating the need to run
a separate power line for the device). Ethernet cabling usually
runs only 100 meters; through the use of the PD-Switch, the outer
range of an Ethernet network can be extended by an additional
100 meters.

With multiple port configurations, the PD-Switch provides a variety
of port options while increasing port density. PD-Switches come
equipped with one "PD" RJ-45 port and either:

Four 10/100Base-T RJ-45 data ports•
Three 10/100Base-T RJ-45 data ports and one SFP data port•
Two 10/100Base-T RJ-45 data ports and one 100Base-FX fiber •
data port

RoHS Compliant

www.imcnetworks.com

Application Example

The PD-Switch has been connected to a central (PoE) PSE-Switch, extending the range of the network and
increasing port density by using a combination of RJ-45 ports and fiber ports.

800-624-1070

Technical Specifications

RoHS-Compliant•
Acts as a PD – Powered Device•
IEEE 802.3x 10/100Base-T•
IEEE 802.3u Auto-Negotiating•
IEEE 802.3af Power Over Ethernet, Powered (PD)•
RFC-2474 and RFC-2475 DiffServ/ToS•
High Priority port•
AutoCross and Auto-Negotiation on all ports•
Includes diagnostic LEDs•
Maximum 1,916 byte Packet Size•
Broadcast Storm Protection•
50/125µm or 62.5/125µm multi-mode•
9/125µm single-mode •
Available for single-strand fiber•
Small, rugged design•
Supports Half and Full-Duplex operation•

Connectors:

RJ-45 and optional ST, SC or SFP•

Regulatory Approvals:

FCC Class A•
CE•

Dimensions:

1.55”H x 4.75”L x 7.31”D
(3.94cm H x 12.07cm L x 18.57cm D)

Shipping Weight:

1.8 lbs (.82 kg)

Operating Temp:

32° to 122°F (0° to 50°C)

Storage Temp:

-13° to 158°F (-25° to 70°C)

Humidity:

5% to 90%, non condensing,
0 to 10,000 ft. altitude

Power Rating:

36V DC-50V DC, 56mA-40mA

Fiber Optics Specifications

For each product listed below in the Ordering Information section, the number in the [XX] denotes an approximate fiber distance based on
industry-standard fiber specifications and worst-case (connector loss, aged fiber, splices, etc.) installations. Longer distances can typically be
achieved. Actual distances may vary for each installation. For complete power budgets and information on calculating specific distances, visit www.
imcnetworks.com/go/fcs or contact IMC Networks Fiber Consulting Services at 949-465-3000. Twisted pair distance is 100 meters.

Ordering Information

PART NUMBER DESCRIPTION DISTANCE

PD-Switch

852-16440 PD-Switch, TX/5 100 m

852-16441 PD-Switch, TX/4 + SFP Various

852-16442 PD-Switch, TX/3 + TX/SX-MM850-ST 2 km

852-16443 PD-Switch, TX/3 + TX/SX-MM850-SC 2 km

852-16444 PD-Switch, TX/3 + TX/FX-MM1300-ST 2 km

852-16445 PD-Switch, TX/3 + TX/FX-MM1300-SC 2 km

852-16446 PD-Switch, TX/3 + TX/FX-SM1310/PLUS-ST 40 km

852-16447 PD-Switch, TX/3 + TX/FX-SM1310/PLUS-SC 40 km

852-16448 PD-Switch, TX/3 + TX/FX-SM1310/LONG-ST 80 km

852-16449 PD-Switch, TX/3 + TX/FX-SM1310/LONG-SC 80 km

852-16450 PD-Switch, TX/3 + TX/FX-SM1550/LONG-SC 80 km

PD-Switch Single Strand Fiber *

852-16470 PD-Switch, TX/3 + TX/SSFX-SM1310-SC (1550 rcv) 20 km

852-16471 PD-Switch, TX/3 + TX/SSFX-SM1550-SC (1310 rcv) 20 km

852-16472 PD-Switch, TX/3 + TX/SSFX-SM1310/PLUS-SC (1550 rcv) 40 km

852-16473 PD-Switch, TX/3 + TX/SSFX-SM1550/PLUS-SC (1310 rcv) 40 km

852-16474 PD-Switch, TX/3 + TX/SSFX-SM1310/LONG-SC (1550 rcv) 60 km

852-16475 PD-Switch, TX/3 + TX/SSFX-SM1550/LONG-SC (1310 rcv) 60 km

*These products have single-strand fiber technology. Deploy in pairs, or connect to another compatible IMC Networks single-strand fiber product.
For more information go to: www.imcnetworks.com/products/SSFX.cfm

IMC Networks

Headquarters

19772 Pauling
Foothill Ranch, CA 92610
TEL: [phone]
FAX: [phone]
[e-mail]
www.imcnetworks.com

IMC Networks

Europe

Herseltsesteenweg 268
B-3200 Aarschot | Belgium
TEL: [phone]
FAX: [phone]
[e-mail]

IMC Networks

Eastern US/Latin America

18840 US Hwy. 19 North Suite 400
Clearwater, FL 33764
TEL: [phone]-8071 (Latin)
FAX: [phone]
[e-mail]

IMC Networks

Fiber Consulting Services

For information call:
TEL: [phone]
1-800-624-1070 (US/CAN)
[phone] (Europe)
[e-mail]

Copyright © 2007 IMC Networks. All rights
reserved. The information in this document is
subject to change without notice. IMC Networks
assumes no responsibility for any errors that may
appear in this document. Specific product names
may be trademarks or registered trademarks and
are the property of their respective companies.

DS-PD-Switch-0804