Imaxrc X350 User Manual

X350 MANUAL
MORE POWER 350W 15A
X350 specific for Hobby gay’s needs!
New Chager X350 Released
iM·OS System
(System: iM·OS V2.11)
Touch Screen c harger
Touch Screen Operation
4.3 inch touch screen make the operation more convenient
x
p
2
7
2
X
0
ch
8
4
-in
.3
4
4.3-inch scr een
4.3 inch display screen
4.3 inch TFT display screen, WQV­GA(480*270),65 thou­sand resolution
The newly developed dedi cat ed
charger operating syste m
i M·O S
A whole new OS system for X350 profession­al charger with high efficiency
USB Port
Output 5V 2.1A USB port specially design for
USB output 5V 2A
Special custom for iPad
iPhone and smartphone charging.
Multiple languages customization
segaugnal elpitluM
customization
A whole new product
definition method
32 bit processor All in one
High precision dual-core 32-bit
32 BIT processo rs
ARM processor for smoother operation
A whole new product definition method
Entirely new design adapter board more
New definition all in one
balance port
beautiful, simpler and safer.
Type
X350 support more than 6 type batteries LiPo / Lilon / LiFe / NiMh / NiCd / Pb
Type
Load
Loading Common Use Battery Setting
Load
Current
Input / Output Current Charging 0.1-15A Discharging 0.1-6A
Current
Save
Save Common Use Battery Setting
Save
Cells
LiXX 1-6S NiXX 1-16S Pb 1-10S
Cells
Uset
Advanced application Settings
Uset
Mode
Fast Charging Balance charging Charging Discharging Circulating charge/ discharge
Mode
Start
Charging/Discharging
Start
iM·OS System
www.imaxrc.com/x350.html
LiPo
Lipo Battery,Single Nominal Voltage: 3.7V,Charge cut-off voltage 4.2V,Dis-
charge cut-off voltage 3.0V
LiIon
LiIon Battery,Single Nominal Voltage: 3.6V,Charge cut-off voltage 4.1V,-
Discharge cut-off voltage 2.5V
LiFe
LiFe Battery,Single Nominal Voltage: 3.3V,Charge cut-off voltage 3.6V,Dis-
charge cut-off voltage 2.0V
NiMH
NiMH Battery,Single Nominal Voltage: 1.2V,Charge cut-off voltage 1.5V,-
Discharge cut-off voltage 1.0V
NiCd
NiCd Battery,Single Nominal Voltage: 1.2V,Charge cut-off voltage 1.5V,-
Discharge cut-off voltage 0.85V
Pb
Pb Battery,Single Nominal Voltage: 2.0V,Charge cut-off voltage 2.5V,Dis-
charge cut-off voltage1.72V
Balance
Lipo balance charge use CC-CV charging way. The charger will balance the battery voltage when charging, this only for LiPo battery. Please connecting the balance port when charging and discharging. Support 2-6 cells.
Charge
Use CC-CV charging way. On the basis of Users setting current the charger will charge the battery to the cut-off voltage. Warning: The voltage can not balance even connecting the balance port when using LiPo battery.
FastCharge
FastCharge. Almost same as the Charge Mode. The only difference is the current only 1/5 and the other setting only 1/10 of the setting current when finished charging.Warning: The voltage can not balance even connecting the balance port when using LiPo battery.
Storage
Charging and discharging the battery voltage to a certain numerical for easy storage. This function only for LiPo battery which need connecting the balance port. Support 2-6S.
DisCharge
Use CC-CV charging way. On the basis of Users setting current the charger will discharge the battery to the cut-off voltage. Warning: Please connecting to the Balance port when use LiPo battery.
Checker
Measuring Mode. The charger only collect battery primary port and balance port voltage,but can not charge and discharge.
Manual Charge
This function only for NiMH battery which same as The Charge mode.
Cycle
This function only for NiMH battery. On the basis of Users setting current for MiNH battery cycle charging and discharging.The Cycle times is 1-6.
X350 Fundamental Function
www.imaxrc.com/x350.html
Touch Screen
DC IN
IBP
No:201230484397.8
All in one。
The socket name match with the plug,please make sure the right port before using
All in one.
Fuse
Fuse Safety Current : 30A
Dean
JST-XH
Balance port
Glow socket
No:201230484396.3
USB
IBP
No:201230484397.8
No:201230484398.2
Tamiya
EC3
JST/BEC
JR/FUXT60
IBP
Avoiding the switch wires making the balance cable and high current cable into one. It ran perfectly on the very first try.
High heat proof material inserting port. With perfect better insulation,flame retardant and stability.
Due to the engineer testing the measurement data again and again make the IBP easier to use. IBP plug connecting with the socket tightly and easily. Grooved design to prevent the misplug reduces time and effort.The anti-slip design increase friction force and make it more beautiful.
IBP collection charge,balance,Signal transfer and temperature sense functions.
Preparing Connecting Using
www.imaxrc.com/x350.html
1
X350 is a professional RC model battery charger,please view the manual before using. If
you are a fresh man please read this entire operating manual completely before using.
【Warning: 】The warning of charger operation and disclaimer, Please read and abide by
the following terms before operation.
1. This is a sophisticated hobby product. The person who operates the charger should be
professional who master professional knowledge about chargers.
2. Make sure the battery variety you using meets charger requirement. Any kinds of dam-
aged, aged and surface, damaged batteries are prohibited. Besides, choose the suitable
charging program or the charger and the battery will get damaged.
3. Considering of uneven physical property and various batteries never leave the work-
ing charger unsupervised, keep it away from inflammable materials and make sure the
fire-fighting equipment matched.
4. If the battery has suspicious reactions during charging or discharging, such as over-
heating, exhausting, leaking or inflating, immediately disconnect the battery and store it in a
safe ocation, away from people and inflammable materials.
Extras Including
X350 included with 1pcs adapter board,1pcs connect cable and 1 pcs manual.
X350
All in one
5. iMaxRC will not be responsible for any personal injuries and fire disaster caused by
incorrect operation.
I have read this agreement carefully and give up all legal.
Chapter 1 Preparing、Connecting、Using
1
Connect cable Manual
Touch pen
Chapter 1 Preparing、Connecting、Using
2
Connecting X350
Please follow the below steps connecting:
1: Please connecting the cable to the adapter port and the X350 DC IN port, and
then plug the adapter power cord into the socket.
2: Connecting the adapter board into the X350 IBP port.
【NOTE】 USB support 5V 2.1A charging voltage,and also use for iPad / iPod / iP-
hone / HTC and other intelligent electronic equipment. Both the USB and All in one get
charged simultaneously.
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
3
4
3: Please make sure the port connect with battery(Other ports are same as it).
4: Sarting X350
startup X350 to enter the main interface ( Image 1 ).
Copyright © iMaxRC Corporation 2012
Image 1
Showing“Warning and Disclaimer” 2 seconds and will know the copyright and security
information ( Image 2 ). It will be enter into the contacting interface if you can not agree with
the disclaimer, and then you could contact the distributor return the charger ( Image 3 )
5、 is issued involving Nasdaq delayed by copyright and other issues, of the speed within two weeks, call or letter from western China to op en the Portal contact.
I have carefully read the agreement, and give u p all legal claims arising because of the charger caused.
To give up and return To confirm and begin using
Image 2
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
5
6
Image 3
【NOTE】 Please read Disclaimer before doing anything.
Sample 1:Choose a set of LiPo battery charging,please follow the below steps:
Step 1: Touch Type( Image 5 ) Enter into the “Type interface”, and then Touch :LiPo (
Image 6 ) will Enter into main interface go on the next step.
6: Enter into main interface after accepting( Image 4 ). Start to charge and discharge
according to the different battery.
Information Bar
Image 4
Action Bar
Image 5
Image 6
【NOTE】 Information bar can not get touched.
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
7
8
Step 2: Touch ‘Mode’ icon( Image 7 ) to enter into Mode interface. Please choose
battery charge mode ( Image 8 ) and go back to main interface to continue setting.
Step 3: Touch Cells icon ( Image 9 ) to enter into Cells interface. Please set battery packs
by sliding ( Image 10 ). Touch OK to go back to main interface and continue setting.
Image 7
Image 8
Image 9
Image 10
【Note】 There are six charge/discharge modes in Mode interface( Image 8 ), see
iM.OS System function for further details. please set charge/discharge mode according
【Note】Please set according to suitable battery packs.
to your requirement. Image 8 is showing Balance charge mode.
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
9 10
Step 4: Touch Current icon ( Image 11 ) to enter into Current interface. Please set charge
current by sliding ( Image 12 ). Touch OK to go back to main interface and continue setting.
Step 5: If you often use the same battery, please touch Save icon ( Image 13 ) to enter
into Save interface. Touch Unused icon ( Image 14 ) to save the data and it will be easy for
you to charge next time.
Image 11
Image 12
【NOTE】 Set charge current in charge mode and discharge current in discharge
mode.
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
11 12
【NOTE】You could use this function after you have set Type/Mode/Cells and Current
correctly.
Image 13
Image 14
Step 6: You could load your previous data according to X350’s load function. Touch Load
icon ( Image 15 ) to enter into Load interface. Choose the data you want to load ( Image 16 ).
Step 7: Touch Start icon ( Image 17 ) to enter into Start interface. The system will check
battery status automatically. If everything is OK, the charger will begin to charge.( Image
18 )
Image 15
Image 16
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
13
Image 17
Image 18
14
【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to
finish charging process ( Image 19 ).
Average:
Dalta V:
90 3720
75 3100
60 2480
45 1860
30 1240
15 0620
12.60V
0.30A
3000mAh
28
0 100
200
50 150
3.00
5.00
18 06
Input
14.0V
15 05
Type
LiPo
12 04
Mode
Cells
Time
Charge completed!
09 03
Balance
06 02
3 Cells
03 01
01:04:06
000 08 16 24 32 40 48 56 64 (min)
4.204.20 0.004.20 0.00 0.00
Warning
OK
Image 19
【NOTE】 The charger will send out an alert and pop-up window if the setting of the bat-
tery packs is incorrect (Image 20).
Example 2: If you want to charge a pack of NiMh battery, please execute the oper­ation as follows:
Step 1: Touch Type icon ( Image 21 ) to enter into Type interface. Touch NiMh icon to go
back to main interface and continue setting ( Image 22 ).
Image 21
Image 20
Image 22
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
15 16
Step 2: Touch Mode icon ( Image 23 ) to enter into Mode interface. Touch Charge icon
( Image 24 ) to go back to main interface and continue setting.
Step 3: Touch Cells icon ( Image 25 ) to enter into Cells interface. Please set NiMh battery
packs by sliding ( Image 26). Touch OK to go back to main interface and continue setting.
Image 23
Image 24
【NOTE】 There are four charge/discharge modes in Mode interface( Image 24 ), see
iM.OS System function for further details. please set charge/discharge mode accord-
ing to your requirement. Image 24 is showing charge mode.
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
17 18
【NOTE】The battery cannot be charged if each pack of the battery voltage is less than
0.7V, please use the less battery packs to activate charging process. If you need lower
voltage during discharging process, please use the less battery packs to discharge.
Image 25
Image 26
Step 4: Touch Current icon ( Image 27 ) to enter into Current interface. Please set charge
current by sliding ( Image 28 ). Touch OK to go back to main interface and continue setting.
Image 27
Image 28
【NOTE】Please set charge current in charge mode and discharge current in dis-
charge mode. As for Save and Load functions, please see Step5 and 6 in Example1
for further details.
Step 5: Touch Start icon ( Image 29 ) to enter into Start interface. The charger will check
battery status automatically. If everything is OK, the charger will begin to charge ( Image 30 ).
Present
Setting
Battery Type:
LiPo
Mode:
Balance
Cells:
3Cells 11.1V
Current:
C 4.5A D 3A
Image 29
Image 30
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
19 20
【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to
finish charging process ( Image 30 ).
Image 30
【NOTE】The charger will send out an alert and pop-up window if the setting of the bat-
tery packs is incorrect. ( Image 31 ) All Lipo battery packs setting are the same operation.
Example 3: If you want to charge a pack of Pb battery, please execute the opera­tion as follows,
Step 1: Touch Type icon ( Image 32 ) to enter into Type interface. Touch Pb icon ( Image
33) to go back to main interface and continue setting.
Image 32
Image 31
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
21 22
Image 33
Step 2: Touch Mode icon ( Image 34 ) to enter into Mode interface. Touch Charge icon ( Image
35 ) to go back to main interface and continue setting.
Step 3: Touch Cells icon ( Image 36 ) to enter into Cells interface. Please set Pb battery
packs by sliding ( Image 37 ). Touch OK to go back to main interface and continue setting.
Image 34
Image 35
【NOTE】 There are some options in Mode interface ( Image 35 ). Please set accord-
ing to your requirement. Image 35 is showing charge process.
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
23 24
【NOTE】Please set according to suitable battery packs.
Image 36
Image 37
Step 4: Touch Current icon ( Image 38 ) to enter into Current interface. Please set charge
current by sliding ( Image 39 ). Touch OK to go back to main interface and continue setting.
Image 38
Step 5:Touch Start icon ( Image 40 ) to enter into Start interface. The charger will check
battery status automatically. If everything is OK, the charger will begin to charge. ( Image 41 )
Present
Setting
Battery Type:
LiPo
Mode:
Balance
Cells:
3Cells 11.1V
Current:
C 4.5A D 3A
Image 40
Image 39
Image 41
【NOTE】Set charge current in charge mode and discharge current in discharge mode.
As for Save and Load functions, please see Step 5 and 6 in Example1 for further details.
Chapter 1 Preparing、Connecting、Using Chapter 1 Preparing、Connecting、Using
25 26
【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to
finish charging process ( Image 42 ).
2
Image 42
【NOTE】The charger will send out an alert and pop-up window if the setting of the bat-
tery packs is incorrect. ( Image 43 ) All Lipo battery packs setting are the same operation.
Image 43
Chapter 1 Preparing、Connecting、Using
27
X350 Experiments
www.imaxrc.com/x350.html
iM·OS SYSTEM ADVANCED APPLICATION
iM·OS SYSTEM is brand-new software of charger which was Independently research and
develop by iMaxRC. It is the first operation system in the world especially to support touch
screen charger,and it’s going to be Industry standard for touch screen charger series.
Here we will full display the Advanced application Settings for you. Pls touch Uset ( Image 44 )
to enter into advanced application setting interface.( Image 45 )
Touch “Cut off Low Input”( Image 46 ), the information bar on left will skip into setting
menu( Image 47 ), touch “OK” after setting done, it will turn back to interface , then you
can go on with setting of other features.
Cut off Low:
11.0V
Cut off temperaturey:
Battery 60
Cut off capacity:
5.0 Ah
Cut off Time:
120 Minute
Lixx Check Time:
10 Minute
More
Cut off
Low
Input
Lixx
Check
Time
Backlight
Level
Cut off tempe­raturey
Nixx Delta Peak
Buzzer Language
Image 46
Cut off
Capacity
Wasle
Time
Cut off
Time
Cycle Times
Back
10.7 V Cut off
Low
Input
Cut off tempe­raturey
Cut off
Capacity
Image 44
Lixx
Nixx
Cut off Low:
11.0V
Cut off temperaturey:
Battery 60
Cut off capacity:
5.0 Ah
Cut off Time:
120 Minute
Lixx Check Time:
10 Minute
More
Cut off
Low
Input
Lixx
Check
Time
Backlight
Level
Cut off
Cut off
tempe-
Capacity
raturey
Nixx
Wasle
Delta
Time
Peak
Buzzer Language
Cut off
Time
Cycle
Times
Back
Check
Time
Backlight
OK
Level
Image 47
Please find detailed list of features on next page.
Wasle
Delta
Time
Peak
Buzzer Language
Image 45
Chapter 2 Enjoy function of X350 Chapter 2 Enjoy function of X350
29
Cut off
Time
Cycle Times
Back
30
Cut off Low Input
Cut off
Low
Rang of setting:10-11V. Lowest cut off input voltage, charger will stop charging/
Input
discharging when input voltage is lower than setting value.
Cut off Temperature
Cut off
tempe-
Rang of setting: 40-80°C. Cut off Temperature, charger will stop charging/
raturey
discharging when the temperature of batteries is lower than setting value.
Cut off Capacity
Cut off
Rang of setting: 0.1Ah-15Ah. Safety capacity. Charger will Stop charging/dis-
Capacity
charging when capacity of batteries is higher than setting value.
Cut off Time
Cut off
Time
Rang of setting: 10-200mins. Safety time, charger will stop charging/discharg-
ing, when charging/discharging time is less that setting value.
Lixx
LixxCheckTime
Check
Time
Rang of setting: 5-60mins. Time for checking cells count of LiPo battery pack.
NixxDeltaPeak
Nixx Delta Peak
Rang of setting: 5-20mV. NiHm/NiCd Delta peak.
Waste Time
Wasle
Time
Spacing interval between 2 Cycles. Rang of setting: 1-60mins.
Cycle Time
Cycle Times
Rang of setting: 1-6 times.
Backlight Level
Backlight
Level
Rang of setting: 1-10, Brightness level.
Buzzer
Buzzer
Rang of setting: All sounds open, only touch tone closed, All sounds closed.
Language
Language
Language option. Now provisionally only support English interface.
Back
Back
Turn back to main interface
【IMPORTANT NOTE】 X350 charger has 3 parameters to control rotate speed of fan.
1. When temperature of working charger reach 40℃, fan speed will be one level up as
temperature rise by each 2℃
2. When charging power reach 100W, fan speed will be one level up as charging power
rise by each 5W.
3. Fan speed will be one level up as discharging power rise by each 2W.
4. Ciruit power: max.350Watts(charging input > 13.0V)
NOTE: Fan Speed of X350 charger will begin to change in any of above situation.
Chapter 2 Enjoy function of X350 Chapter 2 Enjoy function of X350
31 32
IMPORTANT REMIND
www.imaxrc.com/x350.html
3
Please follow the instruction to operate your X350 charger, to insure safety of you and
charger, and use it easily. Please keep manual within easy reach, to be easy reference for
you and other users.
【NOTE】 Procedures, which if not properly followed, can result in potential nullification
of any vendor warranties or liabilities.
SAFETY PRECAUTIONS AND WARNINGS
【Warning】Procedures, which if not properly followed, create the probability of
property damage, collateral damage, and serious injury OR create a high probability of
superficial injury. iMaxRC will not be held directly responsible for those damage if they
were caused by improper using of user.
Proper Operation Please put X350 charger on flat operating platform. DO NOT insert
any object into air-vent.
NEVER use X350 charger under following operating environment: the environment full of
floating dust, smoke from burning or cooking in air. the place have ultrasonic humidifier (for
unfiltered tap water) working on. In rare cases, these smoke or particles in air may float
into X350 charger from air-vent. This may lead inner surface of screen appear mist.
Do not Maintain Yourself
X350 charger not include any spare part for user to make the maintenance , never dis-
mantle the product by yourselves. Please contact with iMaxRC authorized distributor for
maintenance.
Please note if you dismantle the product by yourselves, this may cause damage of original
device. Such kind of damage is not responsible part of our guarantee.
Water and Humid Place Please keep charger far away from any place wet or moist,
such as bathroom, hand Sink. Keep charger in desiccative place to avoid damage caused
by rainy weather.
Charger Please make sure you are holding plug, not pull cord when disconnect power
supply. To avoid mechanical damage.
Chapter 3 Important Remind Chapter 3 Important Remind
35
·Add: F4 201-205, F518 IDEALAND Baoyuan Road, Baoan,
Shenzhen, P.R.C
·Tel: +86-755-89830228
·Fax: +86-755-29558361
·Web: www.imaxrc.com
iMaxRC CO.,LTD
36
All specications and gures are subject to change without notice. Printed in China © 2013
Loading...