Specications and features are subject to change without notice. Images shown are for illustrative
purpose only. All names of the products are trademarks or registered trademarks of their respective
companies. 2013.10. Ver 1.0
1
Safety Symbol
This manual uses the safety symbols below. They denote critical information. Please
read them carefully.
WARNING
Failure to abide by the information in WARNING may result in serious injury
or life threatening.
CAUTION
Failure to abide by information in CAUTION may result in moderate injury
and/or property or product damage.
ATTENTION
Consult accompanying documents.
The lighting ash with arrowhead symbol in an equilateral triangle, is
intended to alert the user to the presence of un-insulated “Dangerous
Voltage” within the product’s enclosure that of many sufcient magnitude
to constitute a risk of electric shock to persons.
Stand-by Switch. Press to turn the monitor on or off (Stand-by mode).
Diagonal line in circle indicates a prohibited action.
Protective earth(ground).
Fragile.
Handle with care.
Alternating current.
Direct Current.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
SN
Serial Number
Indicates the manufacturing date
Follow instructions for use
●
Power supplied equipment can emit electromagnetic waves, which could inuence,
limit or result in malfunction of the monitor. Please install the equipment in a
controlled environment where such effects are avoided.
●
These XLED-3MPC and XLED-2MPC monitors are intended for use in medical image
system environment but does not support the display of mammography images for
diagnosis. For the diagnosis of mammography digital images, please contact your
local sales representative.
●
Product specications may vary depending on the sales region. Please conrm the
specications within the manual.
3
Table of Contents
Safety Symbol ----------------------------------- 1
Environmental Information ----------------------------------- 4
Safety Introductions ----------------------------------- 5
FCC Information ----------------------------------- 7
VCCI Class B ITE ----------------------------------- 8
PRECAUTIONS ----------------------------------- 9
CAUTION ----------------------------------- 13
Notice ----------------------------------- 15
Introduction ----------------------------------- 16
Installation ----------------------------------- 20
Making use of USB (Universal Series Bus) ----------------------------------- 29
Monitor Specications ----------------------------------- 31
Mechanical Specication and Regulatory ----------------------------------- 33
Power Management ----------------------------------- 35
Trouble shooting ----------------------------------- 36
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Environmental Information
Disposal Information
This product consists of devices that may contain mercury, which must be recycled or
disposed of in accordance with local, state, or country laws (within this system, the
backlight lamps in the monitor display contain mercury). This equipment has required
the extraction and use of natural resources for its production. It may contain hazardous
substances for health and environment. In order to avoid the dissemination of those
substances in the environment and to diminish the pressure on natural resources, we
encourage you to use the appropriate take-back systems. Those systems will reuse or
recycle most of the materials of your end-of-life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those systems. If
you need more information on the collection, reuse and recycling systems,
please contact your local or regional waste administrator. You can also
contact our nearest representative ofce for more information on the
environmental performances or disposal of our products.
Cleaning
The screen is made of thin glass with a plastic front surface and can be damaged if
dropped, hit or scratched. Do not clean the front panel with keton-type materials (e.g.,
acetone), ethyl alcohol, toluene, ethyl acid, methyl, or chloride-these may damage the
panel.
●
Panel: Clean with a soft woolen or cotton towel. Use a watery solution or a mild
commercial glass cleaning solution.
●
Cabinet: Clean with a soft cloth dampened with mild detergent and water. Repeat
this with water only and wipe dry with a dry cloth.
Repacking
Do not throw away the carton and packing materials. We encourage you to keep them
for future use in the case of returning the product for replacement or repair. This ideal
package is specially designed and is not easy to nd.
5
Safety Introductions
General Recommendations
Read the safety and operating instructions before operating the display.
Retain safety and operations for future reference.
Adhere to all warnings of this display and in the operating instructions manual.
Follow all instructions for operation and use.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVERTISSEMENT RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
LCD MONITOR
54IJ
E217340
WITH RESPECT TO ELECTRIC SHOCK,
FIRE AND MECHANICAL HAZARDS ONLY
IN ACCORDANCE WITH UL60601-1 AND
CAN/CSA C22.2 NO. 601.1,
MEDICAL EQUIPMENT CERTIFIED FOR CANADA
Grounding Reliability Can Only Be Achieved When The Equipment ls Connected
To An Equivalent Receptacle Marked “Hospital Only” or “Hospital Grade”
When the unit is used together with other equipment in the patient area, the equipment
shall be connected according to Standard UL60601-1 and IEC60601-1.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Classication
●
Protection against electric shock: Class I Equipment.
●
Degree of protection against electric shock: No applied parts.
●
Degree of protection against the ingress of water: ordinary IPX0.
●
Degree of safety in the presence of ammable anesthetics mixture with air or with
oxygen or with nitrous oxide: Not suitable for use in the presence of ammable
anesthetics mixture with air or with oxygen or with nitrous oxide.
This equipment has been tested and found to comply with the limits for medical
devices to the IEC 60601-1-2:1994. These limits are designed to provide reasonable
protection against harmful interference in a typical medical installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to other devices in the
vicinity. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to other devices, which
can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures :
●
Reorient or relocate the receiving device.
●
Increase the separation between the equipment.
●
Connect the equipment into an outlet on a circuit different from that to which the
other device(s) are connected.
●
Consult the manufacturer or eld service technician for help.
7
FCC Information
1. User Instructions
The Federal Communications Commission Radio Frequency Interference Statement
includes the following warning:
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television receptions, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
●
Reorient or relocate the receiving antenna.
●
Increase the separation between the equipment and receiver.
●
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
●
Consult a local dealer.
User Information
Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. If necessary, consult your
dealer or an experienced radio/television technician for additional suggestions. You may
nd the booklet called How to identify and Resolve Radio/TV Interference problems
helpful. This booklet was prepared by the Federal Communications commission. It
is available from the U.S. Government Printing Ofce, Washington, DC 20402, Stock
Number 004-000-00345-4.
User must use shielded signal interface cables to maintain FCC compliance for the product.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
2.
Declaration of conformity for products Marked with FCC Logo
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two Conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
The party responsible for product compliance:
Provided with this monitor is a detachable power supply cord with IEC320 style
terminations. It may be suitable for connection to any UL Listed personal computer
with similar conguration. Before making the connection, make sure the voltage rating
of the computer convenience outlet is the same as the monitor and that the ampere
rating of the computer convenience outlet is equal to or exceeds the monitor voltage
rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA
conguration 5-15P type (parallel blades) plug cap. For 240 Volt applications use only
UL Listed Detachable power supply cord with NEMA conguration 6-15P type (tandem
blades) plug cap.
IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations of ICES-003.
VCCI Class B ITE
この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づく
クラスB情報技術装置です。この装置は、家庭環境で使用することを目的としていま
すが、この装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を
引き起こすことがあります。取扱説明書に従って正しい取り扱いをして下さい。
9
PRECAUTIONS
1. INSTALLING WARNING
If you see smoke emitting from the monitor, if you smell burning or if you hear strange
noise out of the monitor, you should disconnect all power connections immediately and
contact your dealer for the technical advice. Attempting to use a faulty monitor may
cause re, electric shock, or equipment damage.
Refer all servicing to qualied service technician.
●
Do not attempt to service this monitor yourself as opening or
removing covers may cause re, electric shock, or equipment
damage.
●
Do not open the cabinet or modify the monitor. Opening the
cabinet or modifying the monitor may result in re, electric
shock and will void manufacture warranty.
Do not place this apparatus near or over a radiator or heat
resister, or where it is exposed to direct sunlight or emitted
radioactive sources.
Keep liquids away from the monitor, as it may result in a risk of re
or electric shock. Do not place outdoors, in a humid environment
or where water can splash on the screen.
Do not place the monitor in an unstable location such as shaky
self, a slanted oor or a location exposed to vibration. Place the
monitor in a strong and stable place.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Keep the monitor a good distance from any wall to increase
circulation of air. Increased internal temperature may result in
re, electric shock or equipment damage.
Warning to service technician
Suitable marking provided on the equipment shall be provided in the servicing
instructions to alert a SERVICE TECHNICIAN to a possible hazard, where both of the
following conditions exist :
●
Fuse is used in the neutral of single-phase equipment either permanently connected
of provided with a non-reversible plug.
●
After operation of the fuse, parts of the equipment that remain energized might
represent a hazard during servicing.
2. USAGE WARNING
Use the enclosed power cord and connect to the standard power outlet of
your country.
Be sure to remainwithin the rated voltage of the power cord.
Not doing so may result in re or electric shock.
Power supply AC100-240V~, 50/60Hz, 1.5~0.7A
Make sure to plug the power cord in until it is rmly inserted. When
disconnecting the power cord, make sure to hold the power plug
when pulling the plug from the outlet. Tugging on the cord may
damage and result in re or electric shock.
The monitor must be connected to a grounded main outlet.
Not doing so may result in re or electric shock.
11
Use the correct voltage.
This monitor is designed for use with a specic voltage only. Connection to another
voltage different than specied in this user manual may cause re, electric shock, or
equipment damage.
Power supply AC100-240V~, 50/60Hz, 1.5~0.7A
●
Do not overload your power circuit, as this may result in re or electric shock.
●
Do not touch any signal input, signal output or other connectors, and the patient
simultaneously.
●
External equipment intended for connection to signal input, signal output or
other connectors, shall comply with relevant IEC standard. (e.g., IEC60950 for IT
equipment and IEC60601 series for medical electrical equipment.)
In addition, all such combination - system - shall comply with the standard IEC60601-
1-1, safety requirements for medical electrical systems. Any person who connects
external equipment to signal input, signal output or other connectors has formed at
system and is therefore responsible for the system to comply with the requirements
of IEC60601-1-1. If, in doubt, contact qualied technician or your local representative.
WARNING:
●
Do not modify this equipment without authorization of the manufacturer.
●
To avoid the risk of electric shock, this equipment must only be connected to a
supply mains with protective earth. 接地接続は必ず、電源プラグを電源につなぐ
前に行ってください。又、接地接続を外す場合は、必ず電源ぷらぐを電源から切り離
してから行ってください。
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Handle the power cord with care
Do not place the cord underneath the monitor or other heavy objects.
Do not pull on or tie the cord. If you notice any external damage on the power cord,
please stop using it. Using a damaged cord may result in re or electric shock.
Do not touch a damaged LCD panel directly with bare hands. Do
not use any chemicals such as wax, benzene, alcohol, thinners,
insecticide, air freshener. This many damage the appearance or
erase the printing on the monitor.
You can clean the LCD monitor with a damp cloth if necessary, but
be sure to unplug the power cable rst.
Keep small objects away from the monitor. Small objects can
accidently fall through the ventilation slots and into the cabinet
which may result in re, electric shock or equipment damage.
Never touch the plug and power cord if it begins to thunder
outsides. Doing so may result in electric shock.
13
CAUTION
Handle with care when carrying or moving the unit. Disconnect the power cord and
cables when moving the monitor. Moving the monitor with the cord connected is
dangerous, and it maycause harmful injury to you.
When handling the monitor, grip the bottom of the monitor rmly
with both hands ensuring the panel faces outward before lifting.
Dropping the monitor may result in injury or equipment damage.
Do not touch the power cord with wet hands.
Doing so may result in electrical shock.
Do not block the ventilation slots on the cabinet. Blocking the
ventilation slots prevents proper airow.
Do not place in a dusty or an inammable gas environment, as this
can result in re, electric shock and equipment damage.
●
Use an easily accessible power outlet. This will ensure that you can disconnect the
power quickly in case of a problem.
●
Periodically clean the area around the plug.
●
Dust, eater, or oil on the plug may result in re.
●
Unplug the monitor before cleaning. Cleaning the unit while it is plugged into a
power outlet may result in electric shock.
●
Be sure to pull the power plug out of the outlet if the monitor is to remain unused
or if you are to leave the ofce for an extended period of time for the safety and
power conservation.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Double Pole/Neutral fusing
As an alternative to the above wording, use of the following combination of representative
symbols, which includes the electric shock hazard symbol ISO 3864, NO. 5036, the fuse
symbol IEC-60417-5016 (DB:2002-10), and an indication that the fuse is in the neutral N,
is permitted.
However in this case, the statement shall also be provided in the servicing instructions.
Label Statement
15
Notice
●
This monitor has been adjusted specically for use in the region to which it was
originally shipped. If the product is used outside the region, it may not operate in
the specications.
●
Please wait 20-40 minutes after powering on the monitor before adjusting, as
it takes roughly this same amount of time for the optimum performance of the
electrical parts.
●
The screen may have defective pixels. These pixels may appear as slightly light or
dark area on the screen. This is due to the characteristics of the panel itself, and not
the monitor.
●
The backlight of the LCD panel has a xed life span. When the screen becomes dark
or begins to icker, please contact your dealer.
●
Do not press on the panel or edge of the frame strongly, as this may result in the
display malfunction, such as the interference patterns, etc. If pressure is continually
applied to the LCD panel, it may deteriorate or damage your LCD panel.
●
Do not scratch or press on the panel with any sharp objects, such as a pencil or pen
as this may result in damage on the panel. Do not attempt to brush with tissues as
this may scratch the LCD panel.
●
When you bring the monitor from cold temperature room into a high temperature
room or when your room temperature goes up quickly from low to high, dew
condensation may occur inside and outside the monitor. In this case, do not turn on
the monitor. Please wait till dew condensation disappears. Otherwise it may cause
some damages to the monitor.
●
Prolonged operation of an LCD with the same content on the same screen area
may result in a form of image retention. You can avoid or signicantly reduce the
occurrence of this phenomenon by using a screen saver. You can activate a screen
saver in the “Display Properties” window of your workstation. We recommend setting
screen saver activation after 5 minutes of non-usage. In case you are working with
the same image or an application with static image elements for several hours
continuously (so that the screensaver is not activated), change the image content
regularly to avoid image retention of the static elements.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Introduction
1. Features
●
Large display area:
XLED-3MPC 21.2”
XLED-2MPC 21.3”
●
Multi-input support: DVI and DisplayPort
●
30-bits RGB Color signal input support via DisplayPort
●
10-bits Packed pixel input support via DVI.
●
Uniformity Enhancement Function (LUC)
●
Color calibration with built-in color sensor
●
Precise DICOM calibration with 14-bits LUT and built-in sensor
●
Stable Brightness Control (SBC)
●
Diverse DICOM Modes for diverse application
●
The height /tilt/swivel/pivot adjustable stand
●
Flexible display: Landscape and Portrait mode
●
USB 2.0 Compliance, Uptream port X 1 and downstream port X 3
●
Environmentally Friendly LED Backlights
●
Quick Warm-up : Reduced waiting time for the monitor to be DICOM complied.
17
2. Package Contents
Please contact your local dealer for assistance if any of the listed items is missing or
damaged.
Monitor DVI Signal Cable DisplayPort Cable
USB Driver
Power Cord USB Cable
Manual &
USB Driver Installation CD
Warranty Card
(Not Available In All
Locations)
Panel Cleaner
XLED-3MPC_XLED-2MPC
USER’S MANUAL
3. Controls and Connectors
1) Front Bottom and Side
No Description
①
Input Source button
②
Menu button
③
Enter button
④
Down / Left button
⑤
Up / Right button
⑥
LED Lamp on/off button
⑦
Power LED
- Abnormal or disconnected signal : the LED blinks with green
- OSD on : the LED is green / Otherwise, the LED is off
- Warm-up function enable : the LED is amber
⑧
Soft power on/off button
⑨
Color sensor. Measuring luminance(Y) and color coordination(x,y) on DICOM Calibration
or color calibration
⑩
Ambient light Sensor. Measuring room light on DICOM calibration
19
2) Side and Rear
①
Service port
②
DVI-I connector.
③
DisplayPort Connector.
④
USB Up-stream.
⑤
USB Down-Stream.
⑥
AC Power Input
⑦
USB Down-stream
WARNING: Connecting a USB to the
Service Port ① may cause a serious
damage.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Installation
1. Removing the covers
Remove the connector compartment cover and stand cover shown in the following
pictures.
21
2. Connecting the cables
●
Connect the power cord to the AC input outlet ⑥ on the back of the monitor.
●
Connect the DVI and DisplayPort cable from PC to ② and ③ respectively.
●
Connect the USB cable to ④.
●
Turn on the monitor and computer.
●
Recommended resolution
XLED-3MPC QXGA, 2048x1536
XLED-2MPC UXGA, 1600x1200
WARNING: Use the enclosed power cord and connect to the standard power outlet of your
country. The equipment must be connected to the grounded main outlet
XLED-3MPC_XLED-2MPC
USER’S MANUAL
3. Routing the signal cables
Please make sure to wire tie and secure all cables behind monitor as shown below. If
you need to untie the cables, press the locking to unlock the mechanisms with your
nger and pull out the wire tie towards your direction.
4. Monitor Positioning
Adjust the monitor orientation to your preference with following functions.
Height
Monitor will be shipped in lock position. If you want to adjust the height, rst of all you
need to unlock this default position by pushing the lock button located on the bottom
of the stand, then you will be able to move the head of the monitor up and down.
Lock Botton
23
Rotation
WARNING: A Low height adjustment might cause a scratch on surface of the
monitor’s base stand when rotating monitor. Please set the monitor head at high
height and pull out the bottom portion of the head toward you before you make
rotation. This will help you to avoid the scratches on the stand base and around the
edges of the monitors. You will see the detail instruction sticker on the stand base.
Follow this instruction.
Swivel and Tilt
XLED-3MPC_XLED-2MPC
USER’S MANUAL
5. Monitor Setting
All monitor settings are controlled on OSD. Please make sure that the OSD is in the
unlock state before adjustment.
1) Input Source set
Pressing the
button toggles between DVI and DisplayPort input. The selected input
source message will appear on the OSD.
2) OSD Lock/Unlock
a. Lock out
Press
button and hold for about 5 seconds, then the OSD lock message will ap-
pear if the OSD is locked out properly.
b. Unlock
Press
button and hold for about 5 seconds, then the OSD unlock message will
appear if the OSD is unlocked properly.
3) Brightness Adjustment
a. To activate menu
Press “
” or “ ” button in OSD off.
b. Adjusting
Press “
” or “ ” button for decrease
or increase value.
Brightenss Adjustment
0 100
Down Up
50 %
4) LED Lamp brightness Adjustment
a. To activate menu
Press “
” button for about 5 seconds
in OSD off.
b. Adjusting
Press “
” or “ ” button for decrease
or increase value.
LED Lamp Brightness
0 100
50 %
Down Up
25
5) DICOM Mode
USER
Ultrasound CT/MRI
DICOM White DICOM Blue
a. To activate menu
Press “
” button in OSD off, the DICOM Mode OSD will appear.
b. Adjusting
On the DICOM Mode OSD, Pressing “
” button will set the next DICOM mode.
*The default luminance is subject to be changed without notice.
Gamma Color Temperature Default Luminance
DICOM White DICOM Part14 7500’K 450 cd/m
2
DICOM Blue DICOM Part14 12500’K 350 cd/m
2
CT/MRI DICOM Part14 7500’K 350 cd/m
2
Ultrasound Gamma 2.2 7500’K 350 cd/m
2
USER
User Calibration
available
User Calibration
available
450 cd/m
2
< Color-temperature and gamma as DICOM Mode >
6) Adjusting the settings on Main OSD
DICOM Mode
Back Select Down Up
< Main OSD>
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Accessing the Main OSD:
y Opening the Main OSD : press “
” button.
y Closing the Main OSD : press “
” button on top-menu or makes no adjustment
for certain period (set in the “OSD setting->turns off”).
y Menu navigation : press “
” or “ ” button.
y Entering the sub-menu : press “
” button.
y Adjusting the selected function : press “
” or “ ” button (Highlight will move)
and press “
” button for conrmation, then conrmation mark will move to
the set.
Main menu Icon Sub menu or item Factory Settings Description
DICOM Mode
DICOM White USER 6)A
Or
5)DICOM Mode
DICOM Blue
CT/MRI
Ultrasound
USER
Display Setting
Input Modes Auto 6)B
SBC 450 6)B
Uniformity
Enhancement
Max. 6)B
Power Save Enable 6)B
LUT Enable Enable 6)B
Cooling Fan Speed 20 6)B
Self Diagnosis - 6)B
Factory Reset - 6)B
OSD Setting
Language English 6)C
Position Top Right 6)C
Transparency Solid 6)C
Turn off 10 sec. 6)C
Lock out Locked 6)C
Rotation Portrait 6)C
27
Information Information - 6)D
Luminance
Measurement
-
6)D
Ambient
Measurement
-
6)D
a. DICOM Modes
Refer to 5) DICOM Mode for more detail.
b. Display Setting
Input Mode
●
Auto: Input is automatically taken to Mono or Color by input format.
●
Mono: Input is taken to the 10-bits packed Mono by force.
●
Color: Input is taken to the RGB 24-bits dual link Color by force.
SBC
(Stable
Brightness
Control)
●
250-550: Automatically adjusts the overall light intensity targeting to the
selected luminance.
●
USER: Automatically adjusts the overall light intensity targeting to the
luminance set by a user.
●
OFF: SBC function off
Uniformity
Enhancement
●
OFF: Uniformity off
●
MIN.~MAX.: Uniformity level (The MAX is the most uniform set)
Power Save
●
Enable: Goes into Power Save mode on the power save condition.
●
Disable: Doesn’t get into Power Save mode on the power save condition.
Cooling Fan
Speed
●
0-100: Adjusts the cooling fan speed.
LUT Enable
●
Enable: DICOM LUT enable.
●
Disable: DICOM LUT disable (i.e. panel gamma itself).
Self Diagnosis
●
Visual Test: It shows test patterns by monitor itself.
●
Power Block: It checks if the power blocks inside monitor are correct
or not.
●
Memory Block: It checks if the memory blocks inside monitor are correct
or not.
●
Devices: It checks if the devices inside monitor work correctly or not.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Factory Reset
●
ALL: All of the monitor settings are reset to factory defaults.
●
DICOM Mode: All of the “DICOM Mode” settings are reset to factory
default.
●
Display Setting: All settings of the “Display Setting” are reset to factory
default.
●
OSD Setting: All settings of the “OSD Setting” are reset to factory
defaults.
c. OSD Setting
Language
●
Selects OSD language
●
Supported languages: English, German, French, Spanish, Italian, Russian,
Japanese, Chinese and Korean
Position Selects OSD Position: Top-left, Top-right, Center-middle, Bottom-left or
Bottom-Right
Transparency
●
OSD Transparency set
●
Opaque: OSD is shown with opaque
●
Transparency: OSD is shown with transparent
Turn off Adjusts the OSD off time from when the on button is presse.
Lock out Makes OSD lock or unlock
Rotation You can rotate the OSD according to your display rotation
d. Information
Information
●
Model Name: The display model name
●
Serial Number: The display Serial Number
●
Firmware Version: The current internal Firmware version
●
Display Runtime: Indicates the total operating time of the display
including the time in DPMS
●
Backlight Runtime: Indicates the total operating time of the display
excluding the time in DPMS
Luminance
Measurement
The luminance measured by the IQ Sensor
®
, expressed in nit (cd/m2) unit
Ambient
Measurement
The ambient light measured by the built-in ambient sensor, expressed in
Lux unit
29
Making use of USB (Universal Series Bus)
This monitor provides a hub which supports the USB standard 2.0. When connecting to
a USB compliant PC or another hub, the monitor functions as a hub to which the USB
compliant peripherals can be easily connected.
Environment Conditions of usage
●
PC equipped with USB ports or another USB hub connected to the USB compliant PC
●
Windows 2000/XP/Vista, and Windows 7
●
USB cable (enclosed)
Connection to the USB Hub
1. Connect the monitor to the PC with the signal cable rst, then turn on the PC
2. Connect the upstream port of the monitor to the downstream port of the USB
compliant PC or another hub by using the USB cable.
3. After connecting the USB cable, the USB function can be set up automatically.
Upstream Port:
Connect the USB Compliant PC or another hub using
the USB cable.
NOTE: Install the USB software enclosed CD.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
4. After setting up, the monitor’s USB hub is available for connecting USB compliant
peripherals to the downstream ports of the monitor.
Downstream Port:
Connect the cable from USB compliant peripherals
such as a mouse, keyboard, etc.
31
Monitor Specications
1. XLED-3MPC
Panel Specication
LCD Panel 539.5mm (21.2”)
LCM Mode: IPS-Pro
Response Time: 22ms (Black>White>Black)
Viewable Image Size 431.616(H)mm X 323.712(V)mm
Display Resolution Portrait Landscape
Single Head 1536 x 2048 2048 x 1536
Dual Head 3072 x 2048 4096 x 1536
Pixel pitch 0.21075mm X 0.21075mm
Brightness 900cd/m
2
Contrast Ratio 1400 : 1
Viewing angle 85°/ 85°/85°/85° (up/down/right/left)
Compatibility (Video card)
QXGA 2048 x 1536 @60Hz
INPUT Specication DVI DisplayPort
Input connector DVI-I 20pin DisplayPort connector
Input Signal Dual-Link 4 lanes
RGB 24-bits or single
Packed 10-bits
RGB 30-bits
Sync Type Hsync: 96KHz Hsync: 96KHz
Vsync: 60Hz Vsync: 60Hz
Dot CLK: 260MHz Dot CLK: 260MHz
USB Standard USB specication Rev 2.0
Port Upstream port X 1,Downstream port X 3
Communication Speed 480Mbps, 12Mbps, 1.5Mbps
Plug & Play VESA DDC2B
Power Specication
Power Supply 100~240 Vac ±10%, 1.5~0.7A, 50/60Hz
Power consumption Typical 85W
DPMS Less than 1W
Power management NUTEK
XLED-3MPC_XLED-2MPC
USER’S MANUAL
2. XLED-2MPC
Panel Specication
LCD Panel 540.0mm (21.3")
LCM Mode: IPS-Pro
Response Time: 22ms (Black>White>Black)
Viewable Image Size 432.0(H)mm X 324.0(V)mm
Display Resolution Portrait Landscape
Single Head 1200 x1600 1600 x1200
Dual Head 2400 x 1600 3200 x 1200
Pixel pitch 0.270mm X 0.270mm
Brightness 770cd/m
2
Contrast Ratio 1100 : 1
Viewing angle 85°/ 85°/ 85°/ 85° (up/down/right/left)
Compatibility (Video card)
UXGA 1600 x 1200 @60Hz
INPUT Specication DVI DisplayPort
Input connector DVI-I 20pin DisplayPort connector
Input Signal Dual-Link 4 lanes
RGB 24-bits or single
Packed 10-bits
RGB 30-bits
Sync Type Hsync: 75KHz Hsync: 75KHz
Vsync: 60Hz Vsync: 60Hz
Dot CLK: 162MHz Dot CLK: 162MHz
USB Standard USB specication Rev 2.0
Port Upstream port X 1,Downstream port X 3
Communication Speed 480Mbps, 12Mbps, 1.5Mbps
Plug & Play VESA DDC2B
Power Specication
Power Supply 100~240 Vac ±10%, 1.5~0.7A, 50/60Hz
Power consumption Typical 80W
DPMS Less than 1W
Power management NUTEK
33
Mechanical Specication and Regulatory
1. XLED-3MPC
Mechanical Specication
Dimension Portrait: 378.0mm(W) X 535.9mm(H) X 248.8mm(D)(±2)
Landscape: 506.2mm(W) X 471.8mm(H) X 248.8mm(D)(±2)
Gross: 525.0mm(W) X 640.0mm(H) X 320.0mm(D)(±2)
Weights Net: 11.0Kg / 24.25lb
Gross: 16.5Kg / 36.38lb
Adjustment ability
Height 0~110mm
Rotation 90° (Landscape or Portrait)
Tilt -3°(D) / 15°(U)
Swivel -20°(L) / 20°(R)
Environmental Consideration
Operating Temperature: 0°C to 40°C / 32°F to 104°F
Humidity: 10% to 80%
Maximum Height : 5,000mm
Atmospheric pressure Range : 700hPa to 1060hPa
Storage Temperature: –20°C to 60°C / –40°F to 140°F
Humidity: 30% to 80%
Maximum Height : 5,000mm
Atmospheric pressure Range : 500hPa to 1060hPa
Regulatory
Approvals UL60601-1 / EN60601-1 / IEC60601-1
CE, VCCI, KC, C-Tick, FCC
XLED-3MPC_XLED-2MPC
USER’S MANUAL
2. XLED-2MPC
Mechanical Specication
Dimension Portrait: 378.0mm(W) X 535.9mm(H) X 248.8mm(D)(±2)
Landscape: 506.2mm(W) X 471.8mm(H) X 248.8mm(D)(±2)
Gross: 525.0mm(W) X 640.0mm(H) X 320.0mm(D)(±2)
Weights Net: 11.5Kg / 25.35lb
Gross: 17.0kg / 37.48lb
Adjustment ability
Height 0~110mm
Rotation 90° (Landscape or Portrait)
Tilt -3°(D) / 15°(U)
Swivel -20°(L) / +20°(R)
Environmental Consideration
Operating Temperature: 0°C to 40°C / 32°F to 104°F
Humidity: 10% to 80%
Maximum Height : 5,000mm
Atmospheric pressure Range : 700hPa to 1060hPa
Storage Temperature: –20°C to 60°C / –40°F to 140°F
Humidity: 30% to 80%
Maximum Height : 5,000mm
Atmospheric pressure Range : 500hPa to 1060hPa
Regulatory
Approvals UL60601-1 / EN60601-1 / IEC60601-1
CE, VCCI, KC, C-Tick, FCC
35
Power Management
This Power Management System helps you to save energy by switching your monitor
into a low-power consumption mode when it has not been used for a certain period
of time. Power Management System operates with VESA DPMS compliant video card
installed in your computer.
You use a software utility installed on your computer to set up this feature.
We highly recommend setting DPMS activation after 15 minutes non-usage in order
to optimize your display lifetime and to avoid Image Retention damage. We also
recommend you not to leave the same image or viewing frame too long. Frequent
change of moving the image and viewing frame will help you to avoid Image Retention
( also called “Image Sticky” ) damage on your monitor. We, manufacturer, are not
responsible for this damage.
Power Management Modes
State Normal operation DPMS Standby DPMS Suspend DPMS off
Horizontal Sync Active Inactive Active Inactive
Vertical Sync Active Active Inactive Inactive
Video Active Blanked Blanked Blanked
Power Indicator LED off
Green Flashing
(1sec interval)
Green Flashing
(1sec interval)
Green Flashing
(1sec interval)
Power
Consumption
XLED-3MPC 85W
Less than 1W Less than 1W Less than 1W
XLED-2MPC 80W
Note: This monitor automatically returns to normal operation when horizontal and vertical
sync return. This occurs when you move the computer’s mouse or press a key on the
keyboard.
XLED-3MPC_XLED-2MPC
USER’S MANUAL
Contact Information
Technical Support and Sales – Contact TekLink via:
●
TekLink Website at (http://teklink.rell.com)
●
TekLink Phone Toll Free at (888) 735-7373
Trouble shooting
No picture
●
Make sure that the power cord is completely connected.
●
Make sure that the LCD Monitor and computer power switch are on.
●
Check the signal cable connector for bent or pushed-in pins.
The display image is too light or too dark.
●
Adjust the Brightness or do the factory reset through the Main OSD. Screen is blank
and power indicator is blinking every 1 seconds.
●
Make sure that the signal cable is completely and rmly connected to the display
card or computer.
●
Make sure that the display sources or computer is turned on. (See page 21.)
●
Make sure that the set of monitor input source is what you expect to see as input.
●
Check if the monitor is in the power management mode.
Copyright Notice
This document is copyrighted. All rights are reserved. Neither this document, nor any part
of it, may be reproduced or copied in any form or by any means-graphical, electronic,
or mechanical including photocopying, taping or information storage and retrieval systems
without written permission of Canvys a division of Richardson Electronics © 2013 Canvys a
division of Richardson Electronics. All rights reserved.
Loading...