Image IMTL49105.0 User Manual
Model No. IMTL49105.0
Visit our website at
www.imagefitness.com
new products, prizes,
fitness tips, and much more!
erial No.
S
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
USER'S MANUAL
CALL TOLL-FREE:
1-800-753-4645
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.iconservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.
IMAGE is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: T
following important precautions and information before operating the treadmill.
. It is the responsibility of the owner to ensure
1
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should be used only by persons
weighing 275 pounds or less.
8. Never allow more than one person on the
treadmill at a time.
o reduce the risk of burns, fire, electric shock, or injury to persons, read the
2. Failure to use a properly functioning surge
1
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
13. Keep the power cord and the surge suppressor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 19 if the treadmill is
not working properly.)
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
OPERATION and ADJUSTMENT).
16. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women.
Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
When connecting the power cord (see page 11),
10.
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
Use only a single-outlet surge suppressor that
11.
meets all of the specifications described on
page 11. To purchase a surge suppressor, see
your local IMAGE
telephone number on the front cover of this
manual and order part number 146148, or see
your local electronics store.
dealer or
call the toll-free
18. The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Never leave the treadmill unattended while it
19.
is running.
the power cord when the treadmill is not in
use.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW
AND MOVE THE TREADMILL on page 17.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
When folding or moving the treadmill, make
21.
sure that the storage latch is fully closed.
Inspect and properly tighten all parts of the
22.
treadmill regularly.
Always remove the key and unplug
TO FOLD
3
23. Never insert any object into any opening.
24. DANGER: Always unplug the power
ord immediately after use, before cleaning
c
the treadmill, and before performing the
maintenance and adjustment procedures de-
cribed in this manual. Never remove the
s
motor hood unless instructed to do so by an
authorized service representative. Servicing
ther than the procedures in this manual
o
should be performed by an authorized service representative only.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on the treadmill. If a decal is missing, or if
it is not legible, call the toll-free telephone number on the front cover of this manual
and order a free replacement decal. Apply the decal in the location shown. Note:
The decals are not shown at actual size.
4
BEFORE YOU BEGIN
hank you for selecting the new IMAGE
T
ill. The 17.0 R treadmill combines advanced technol-
m
ogy with innovative design to make your workouts at
home more effective and enjoyable. And when you’re
not exercising, the 17.0 R treadmill can be folded up, requiring less than half the floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, see the front cover of this manual. To
help us assist you, please note the product model
Accessory Tray
Handrail
®
7.0 R tread-
1
umber and serial number before calling. The model
n
umber of the treadmill is IMTL49105.0. The serial
n
number can be found on a decal attached to the treadmill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.iconservice.com/registration.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Fan
Console
Key/Clip
Storage Latch
Walking Belt
Foot Rail
BACK
Rear Roller
Adjustment Bolts
Upright
Reset/Off
Circuit Breaker
Power Cord
Cushioned Walking Platform
for maximum exercise comfort
RIGHT SIDE
5
ASSEMBLY
Nut (47)–4
Handrail Bolt (20)–4
Endcap Screw
(95)–4
Upright Bolt (40)–4
Frame Washer
(33)–2
1/4” Star Washer
(21)–2
Silver Ground
Screw (27)–2
Wheel Spacer (44)–4
Console
Bolt (22)–2
Frame Bolt (32)–2
Wheel Bolt (89)–2
3/4” Screw (2)–8
Upright Star
Washer (39)–4
Handrail Star
Washer (19)–4
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480.
Assembly requires two persons.
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included allen wrenches and your own phillips screwdriver ,
rubber mallet , adjustable wrench , and wire cutters .
For help identifying the assembly hardware, see the drawings below.
to see if it has been pre-assembled.
Set the treadmill in a cleared area and remove all packing materials. Do not
If a part is not in the parts bag, check
1. Make sure that the power cord is unplugged.
Have a second person hold the Upright Base (48) in the
position shown, with the wheel holes at the top. Identify
the Left Upright (31), which is marked with a sticker.
Orient the Left Upright so the indicated bracket is in the
position shown, and attach the Left Upright to the Upright
Base with two Upright Bolts (40) and two Upright Star
Washers (39). Do not tighten the Upright Bolts yet.
1
6
Wheel Holes
Bracket
31
48
39
40
2. Orient the Right Upright (36) so the square hole near the
ower end is in the position shown. Attach the Right
l
Upright to the Upright Base (48) with two Upright Bolts
40) and two Upright Star Washers (39). Do not tighten
(
the Upright Bolts yet.
Attach each Wheel (45) to the Upright Base (48) with a
heel Bolt (89), two Wheel Spacers (44), and a Nut (47)
W
s shown.
a
Wheels should turn freely.
Cut the tie securing the Wire Harness (28) in a bundle.
3.
not remove the large colored tie on the end of the
Wire Harness.
Orient the Upright Base (48) so the Wheels (45) are at the
bottom. Next, position the Upright Base and the Uprights
(31, 36) around the frame assembly as shown.
Have another person lift the front of the frame assembly
and hold it. Insert the Wire Harness (28) into the square
hole near the lower end of the Right Upright (36) and out
of the top. Next, raise the Uprights (31, 36) so the Upright
Base (48) is flat on the floor. Make sure that the end of
the Wire Harness does not fall into the Right Upright;
it may be helpful to hold the colored tie on the end of
the Wire Harness.
o not overtighten the Wheel Bolts; the
D
Do
2
3
44
89
31
45
44
47
Square Hole
36
Colored Tie
28
44
89
47
45
36
39
48
40
Hole
48
28
45
Frame Assembly
4. Open the included grease packet, and apply equal
amounts of grease to both sides of each Frame Spacer
(34).
Hold one of the Frame Spacers (34) between the frame
assembly and the Right Upright (36); make sure that
the Frame Spacer is oriented as shown in the inset
drawing. Insert a Frame Bolt (32) through a Frame
Washer (33), the Right Upright, the Frame Spacer, and
the bracket on the frame assembly. Be careful not to
pinch the Wire Harness (28) in the Right Upright.
Tighten a Nut (47) several turns onto the Frame Bolt, but
do not fully tighten the Nut yet.
Repeat this step on the left side. Note: There is not a
wire harness on the left side.
Remove the colored tie from the Wire Harness (28).
4
34
Frame Assembly
28
Colored Tie
36
47
34
59
34
33
32
Left
Side
Right
Side
7
. Identify the right Handrail (18) (the Latch Housing [30] is
5
attached to the left Handrail). Next, identify the Right
Handrail Endcap (92), which has an “R” near the two
screw holes. Slide the Right Handrail Endcap onto the
ight Handrail. Next, hold the right Handrail near the
r
Right Upright (36), and insert the Wire Harness (28)
through an Upright Cap (90), into the hole in the bottom
of the right Handrail, and out of the indicated hole in the
op. Then, remove the tie from the Wire Harness.
t
Insert two Handrail Bolts (20) with two Handrail Star
Washers (19) through the right Handrail (18) and the
Upright Cap (90). Set the right Handrail and the Upright
Cap on the Right Upright (36) while sliding the lower end
of the right Handrail onto the bracket on the Right
Upright. Hand tighten the two Handrail Bolts into the
right Handrail and the Right Upright. Next, slide the Right
Handrail Endcap (92) against the Right Upright, and
tighten two Endcap Screws (95) into the Right Handrail
Endcap. Then, tighten the two Handrail Bolts.
sure that the Wire Harness (28) is not pinched.
Attach the other Handrail (18) to the Left Upright (31) as
described above.
Make
5
0
2
8
1
19
30
95
1
3
28
20
19
90
Screw
Holes
92
1
8
36
95
6. Hold the Console Base (26) near the right Handrail (18).
Attach the end of the ground wire on the Console Base
to the indicated small hole in the Handrail with a Silver
Ground Screw (27).
Connect the Wire Harness (28) to wire harness on the
Console Base (26). Make sure to connect the connec-
tors properly (see the inset drawing). The connectors
should slide together easily and snap into place. If
the connectors do not slide together easily and snap into
place, turn one connector and try again. IF THE CON-
NECTORS ARE NOT CONNECTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE POWER
IS TURNED ON.
7. Set the console assembly on the Handrails (18); insert
the excess wiring down into the right Handrail. Attach the
console assembly with four 3/4” Screws (2), two Console
Bolts (22), and two 1/4” Star Washers (21) as shown.
Make sure that no wires are pinched. Start all four
Screws and both Console Bolts before tightening
any of them.
6
26
27
28
7
18
Console Assembly
Ground
Wire
18
28
18
21
2
22
2
21
22
8
Loading...