iLuv Creative Technology AUDCLICK User Manual
THE AUD CLICK IS DESIGNED FOR HOME USE WI-FI CONNECTIVITY AND
Bottom button
Top button
LED indicator
Volume control
WILL NOT FUNCTION PROPERLY WITHIN AN OFFICE ENVIRONMENT
WHERE WI-FI PROTECTIVE FIREWALLS ARE OPERATING.
WHAT’S INCLUDED CONTROLS
Aud Click Main Unit
Quick Start Guide
Top button
Press the top
button to
play/pause music
Volume control
Turn clockwise to
raise volume.
Turn counter clockwise
to lower volume.
Bottom button
POWERING UP
WiFi is connected
Flashing white LED
WiFi is not connected
White LED
To power on, press and hold the
WPS (WiFi protected setup) button,
located at the bottom of the unit
for 2 seconds. Once on, wait a few
seconds for unit to start up and Aud
Click will default into WiFi mode.
LED will ash white until
connected. Once WiFi is successfully set up, LED will not ash but
will light up white.
LED indicator
SETTING UP
1. Download the Aud Click APP
to your smartphone (available in the apple
or android app stores)
2. Follow the procedure on the app
to setup Aud Click
3. On the app, go to Amazon and input
your Amazon account info to set up Alexa.
After set up, Aud Click can run by itself without APP.
WIFI OPERATION
BATTERY CHARGING
1. Power on the unit. Unit should be under WiFi mode
and white LED will stay on.
1
2. Press and hold the top ring for 2 seconds, until you can hear
prompting tone and white LED is ashing. Then, you can
command Aud Click to operate by pressing top button
and using voice command.
Below is some example:
• Play Music - Click and Say “Play music on iTunes Radio”
2
• Weather - Click and Say "What's the weather in New York?"
• Spelling - Click and Say "How do you spell Apple?"
BLUETOOTH PAIRING (MANUALLY)
1. Power on the unit, and double click the top ring.
LED indicator will change to blue indicating that
the Aud Click is in Bluetooth mode.
2. Press the WPS button, located at the bottom of the unit once.
Aud Click will go into Bluetooth pairing mode and LED indicator
will ash blue.
3. On your smartphone or tablet turn on Bluetooth and then select
"iLuv AudClick". Once Bluetooth is connected,
Blue LED will stop ashing and stay on.
4. Press the top ring to play/pause music.
Turn the silver ring clockwise to raise the volume,
and counter-clockwise to lower the volume.
5. Double click the top ring to switch back to WiFi mode.
RESET THE UNIT
Flasinhg Red Indicator
Time to charge
Voice Prompt
“Battery is low”
USB charging cable
DC 5V, 1A output
White LED
Fully charged
Noted : We recommend you keep charging the unit if you set alarms
to prevent battery low and missed alarm.
1. If battery is low, the LED indicator will ash red.
Voice promptwill tell you that battery is low and
it is time to charge the Aud Click.
2. Using the included USB charging cable,
connect one side to your PC or smartphone's USB port
(DC 5V, 1A output) and the other side to the Aud Click.
3. While charging, LED indicator will remain red until fully
charged. Once fully charged, LED will turn o.
Remark: USB only charging function
RESET
1. If the unit behaves abnormally, just use a paper clip or
similar shaped tool to press the reset button which is located
at the bottom of the unit.
2. After reset is done, you need to set it up it
from the beginning again.
THE DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT WASTE PRODUCTS ON THE P
ART OF FINAL USERS IN THE EUROPEAN UNION
This symbol on the product or on the container indicates that this product cannot be eliminated with the
general waste.The user is responsible for eliminating this kind of waste by throwing them away at a
“recycling point” specifically for electrical and electronic waste.Selective collection and electrical
equipment recycling contribute to preserve natural resources and warrant waste recycling to protect
environment and health.In order to receive further information about electrical and electronic waste
collecting and recyling,contact your Local Council,the service of household waste or the establishment
where the product was acquired.
Loading...