ILP RB3 Series, RB3-13L-U-50, RB3-19L-U-40, RB3-13L-U-40, RB3-19L-U-50 Installation Instructions Manual
...
LED ROUND HIGH BAY
INSTALLATION INSTRUCTIONS
CAUTION
!
PLEASE READ INSTRUCTIONS BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCE.
Electrical products can cause death or injury, or damage to property. If in any doubt about the installaon or use of this product, consult a competent electrician.
WARNING
!
1. To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings
and instrucons included with and on the fixture box and all fixture labels.
2. Before installing, servicing, or performing roune maintenance on this luminaire, follow these general precauons.
3. Installaon, service and maintenance of luminaries should be performed by a qualified licensed electrician.
4. For the installaon: If you are unsure about the installaon or maintenance of the luminaire, consult a qualified licensed electrician and check your local
electrical code.
5. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
6. Please keep the RB3 away from any corrosive substance. When you clean it, please use damp or dry cloth.
WARNING
!
1. Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
2. Turn off the power when you perform any maintenance.
3. Verify that supply voltage is correct by comparing it with the luminaire label informaon.
4. All wiring connecons should be capped with UL approved wire connectors.
5. Suitable for Wet Locaons
General Wiring Diagram
Black (Line)
100-277V
White (Neutral)
Green (Ground)
LED DRIVER
Purple (Dim-)
Purple (Dim+)
Blue (-)
Red (+)
Installaon Steps
REFLECTOR / DIFFUSER INSTALLATION (OPTIONAL)
· Insert provided screws to the designated locaons on the fixture housing. Install screws half way, leaving enough space (1/8" – 3mm) between the housing and
the end of the screws to be able to insert through the keyholes of the reflector/diffuser (Figure 1).
· Align the reflector/diffuser with the housing and insert screws through the reflector/diffuser keyholes. Rotate clockwise to lock the reflector/diffuser (Figure 2).
· Lock the screws to secure the reflector/diffuser (Figure 3).
· Finished result as shown in (Figure 4).
· Follow RB3 installaon steps to complete the installaon.
Screw
Figure 1 Figure 2 Figure 3 Figure 4
Reflector
LED ROUND HIGH BAY
INSTALLATION INSTRUCTIONS
Installaon Steps
TURN OFF POWER FROM MAIN CIRCUIT BREAKER
SUSPENDED MOUNTING
· Insert wires through the provided hook and screw the hook to the driver housing (Figure 1). Tighten the provided screw to secure the hook (Figure 2).
· Hang the fixture to customer supplied chain or mounng hardware (Figure 3).
· Tighten hook’s screw to secure the installaon (Figure 4).
· Make appropriate electrical connecons.
Screw Hole
Screw
Figure 1 Figure 2 Figure 3 Figure 4
SURFACE MOUNTED WITH MOUNTING BRACKET
· Locate (2) Bracket B and aach to the designated locaons on the fixture housing with provided screws (Figure 1).
· Locate (1) Bracket A and aach to secured Bracket B, on both sides, with nylon and steel gaskets, screws and nuts (Figure 2).
· Adjust the angle of Bracket A to the desired posion and sure the posion with locking screw, steel gasket and nut on both sides (Figure 3).
· Aach the bracket to the ceiling or wall.
· Make appropriate electrical connecons.
Screws
Bracket B
Figure 1
Figure 2
Bracket A
Bracket B
Nylon Gasket
Stainless Steel Gasket
Bracket A
Nylon Gasket
Nut
Stainless Steel Gasket
Bracket B
Screw
Screws
Figure 3
Part Number Power
RB3-13L-U-40
RB3-13L-U-50
RB3-19L-U-40
RB3-19L-U-50
RB3-25L-U-40
RB3-25L-U-50
RB3-31L-U-40
RB3-31L-U-50
100W
100W
150W
150W
200W
200W
240W
240W
Bracket A
Stainless Steel Gasket
Nut
Working Current Input Voltage
1100mA
1100mA
1650mA
1650mA
2200mA
2200mA
2640mA
2640mA
Screw
Efficacy
AC100-277V 130lm/w
Loading...