Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
1
From
www.illuminated-mirrors.uk.com
Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
2
LED Magnification Mirror with
3x Magnification area
and Sensor
(Model Numbers: 100877K99 & 100)
Thank you for purchasing our illuminated mirror(s).
To avoid product damage, personal injuries, carefully read, understand, and follow all
the Instructions in this installation guide before installing the product.
Save this manual for future reference.
Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
3
WARNING!
To avoid the risk of electrocution, please turn off the electricity
supply mains before commencing the installation.
Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
4
CONTENT
I. STANDARDS
a. Safety Instructions
b. IP Rating
c. Bathroom Zones
II. PARTS
III. STEP-by-STEP INSTALLATION
Step 1: Route a 240v mains electric cable near where you would like to install the mirror.
Step 2: Pull the 240v electrical connection through the mirror back plate.
Step 3: Using a spirit level, make sure the back plate is level and in the correct position on the
wall.
Step 4: Next using a drill and screw driver fix the back plate on to the wall, with the fittings
supplied.
Step 5: Now the Back plate is fixed to the wall you can connect the lights, demister pad and
shaver socket to the 240v electrical supply.
Step 6: Simply place the mirror over the back plate and using a screw driver tighten and fix it
in place.
IV. CARE AND CLEANING
V. FAQs
Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
5
I. STANDARDS
a. Safety Instructions
Installation of this product can require a qualified electrician. If necessary, hire or
consult a qualified electrician in accordance with the current IEE Wiring Regulations
and UK Building Regulations for assistance before continuing.
Please turn off the electricity supply mains before commencing the installation.
This light fitting is a class I product and therefore must be earthed.
Always use the correct type and wattage bulb; never exceed the stated/rated wattage as
this could overheat the transformer.
b. IP rating
The IP Code (or Ingress Protection Rating, sometimes also interpreted as
International Protection Rating) consists of the letters IP followed by two digits or one
digit and one letter and an optional letter. These two digit numbers refer to the level of
protection the product has and it is important that you choose fittings with correct ratings
according to where they are installed within the bathroom.
c. Bathroom Zones
Our illuminated mirror has special protection against the ingress of moisture and is
manufactured to meet IP44 standard, thereby making it suitable for use in Zones 2 and 3
of a bathroom with reference to the below diagram.
Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
6
II. PARTS
(Figure i) – LED Magnification Slimline Mirror and its parts.
Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
7
III. INSTALLATION
Earth (E)
GREEN
Neutral (N)
BLUE
Live (L)
BROWN
Please turn off the electricity supply mains before commencing the installation.
Wiring Colours:
Step 1:
Route a 240v mains electric cable near where you would like to install the mirror.
Step 2:
Pull the 240v electrical connection through the mirror back plate.
Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
8
Step 3:
Using a spirit level make sure the back plate is level and in the correct position on the
wall.
Step 4:
Next using a drill and screw driver fix the back plate on to the wall, with the fittings
supplied.
Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
9
Step 5:
Now the Back plate is fixed to the wall you can connect the lights, demister pad and
shaver socket to the 240v electrical supply.
Step 6:
Simply place the mirror over the back plate and using a screw driver tighten and fix
it in place. And your mirror is ready to use!
Diamond X Collection | www.illuminated-mirrors.uk.com
Model: 100877K99 & K100
INSTRUCTION MANUAL
10
IV. CARE AND CLEANING
Please be aware when cleaning the mirror surface, do not to use abrasive materials as
these will damage the overall finish.
V. FAQs
1. What is a LED Mirror?
A LED Mirror uses Energy Saving LED light bulbs. They are Waterproof Rated IP44
for use in bathrooms and include clever technology like, Infra-Red on/off sensors, AntiMist demister pads and a shaver socket.
2. On/Off Infra-Red Sensor?
All our LED Mirrors include Infra-Red on/off Sensor, simply wave your hand to the
sensor and it will instantly powers up the lights and demister pad. You need to wave your
hand 3-6 inches away to On/Off your mirror cabinet.
3. Where is the sensor located?
The sensor is located on the bottom of the mirror and not on the front of the glass.
4. Can I isolate the sensor so the led's come on with my bathroom lighting?
Yes, just call us for instructions and we shall email them to you, it's extremely easy!
5. Heated Demister Pad Mirrors?
Just turn on the lights via Infra-Red sensor and the heat pad removes the steam from
the glass on the door.
6. How do I activate the demister pad?
The demister pad works automatically when the lights are turned on and off.
7. Is the mirror tinted glass?
No, the mirror is perfectly clear reflective mirror glass.
8. Is the mirror CE & ROHS certified?
Yes!
*****
Loading...