iLive ITPW891B, SW311B User Manual

Page 1
USER’S GUIDE
V:1433-0214-11
For the most up-to-date version of this User’s Guide, go to www.ilive.net
ITPW891B / SW311B
Sound Bar with Wireless Subwoofer for Any TV
Page 2
iLive2
WARNING: Shock hazard - Do Not Open.
AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR
Mains Plug or Direct plug-in adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the Mains Plug or Direct plug-in adapter should be disconnected from the mains socket outlet completely.
La che d’alimentation ou adaptateur de courant est utilisé comme dispositif de déconnexion et doit rester accessible pendant l’utilisation. Pour mettre l’appareil hors tension, la che ou adaptateur de courant doit être débranché de la prise de courant.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
No mezcle baterías viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.).
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité.
CAUTION: Use of any controls or adjustments or performance of procedures other than those herein specied may result in hazardous radiation exposure.
WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface.
WARNING: Use of this unit near uorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any uorescent lighting, as it may be the cause.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
PRÉCAUTION: Danger d’explosion si les piles sont remplacées de façon incorrect. Remplacer les piles seulement par le même type de pile ou l’équivalent.
WARNING: There is a danger of explosion if you attempt to charge standard Alkaline batteries in the unit. Only use rechargeable NiMH batteries.
WARNING: The battery, batteries, and battery pack shall not be exposed to excessive heat such as sunshine, re, or the like.
The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER­SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Warnings and Precautions
Page 3
Customer Support: 1-888-999-4215 iLive 3
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12.
This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts.
Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Important Safety Instructions
Special note: When placing your unit on a lacquered or natural nish, protect your furniture with a cloth or other protective material.
WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.
Battery shall not be exposed to excessive heat such as sunshine, re or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la lumière du soleil, au feu ou autres choses de semblable.
Caution marking is located at the rear or back of the apparatus.
Attention marquage est situé à l’arrière ou à l’arrière de l’appareil
The marking information is located at the rear or back of apparatus.
Les informations de marquage est situé à l’arrière ou à l’arrière de l’appareil.
FCC Warnings
Additional Warnings
Page 4
iLive4
Sound Bar with Wireless Subwoofer for Any TV
ı Made for iPod and iPhone ı Plays and charges docked iPod and iPhone ı App-enhanced ı FM radio (PLL) ı Station memory presets (20 FM) ı High power amplier ı BBE® professional-grade sound technology ı Enhanced audio quality ı iPod and iPhone controls ı iPod and iPhone authentication IC ı 2 Composite video inputs ı Composite video output ı Component video output ı SubWoofer output ı 2 RCA stereo audio inputs ı 3.5mm audio input
ı Preset EQ ı Bass controls ı Treble controls ı Digital volume control ı Wooden speaker enclosures ı Last user settings memory ı Wall mountable ı Full-function remote ı Cloth speaker grill ı Negative LCD display with white backlight ı Digital clock ı Timer ı Sleep Timer ı Dual voltage: 220V/50Hz, 120V/60Hz ı AC power: built-in AC power cable
ı 2.4Ghz wireless receiver ı Subwoofer input ı Volume control ı Pairing button ı Wooden speaker enclosure ı Cloth speaker grill ı AC power: built-in AC power cable
ı Remote control: requires 2 AAA batteries
(included) ı RCA video cable ı Wall-mount hardware: 2 spacers, 4 screws ı FM wire antenna
Sound Bar - Features
Wireless Subwoofer - Features
Included
Setup
AC power: built-in AC power cable Requires 2 AAA batteries (included)
FM ANT
Pr
OUT
R
COMPENTENT OUT VIDEO
AUDIO IN
SW OUT
Y
Pb
IN
L
RESET
AC 120V/60Hz
FM ANT
Pr
OUT
R
COMPENTENT OUT VIDEO
AUDIO IN
SW OUT
Y
Pb
IN
L
RESET
AC 120V/60Hz
Sound Bar and Wireless Subwoofer - Power Remote
Page 5
Customer Support: 1-888-999-4215 iLive 5
Table of Contents
Warnings and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Sound Bar with Wireless Subwoofer for Any TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
iPod and iPhone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FM Radio, Clock, Sleep Timer, and Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wireless Subwoofer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Basic Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Video and Audio Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
BBE Professional Audio Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Mounting to a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Company Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Page 6
iLive6
Introduction
Power
Press to power the sound
bar o and on.
Source
Press to switch between FM,
iPod, Aux, AV, and Line modes.
Volume
Press to adjust the volume.
Pairing
Press to pair the sound bar
with a wireless subwoofer.
3.5mm Audio Input (Line)
Reset
Press using a paperclip or like
object to reset the sound bar
to it’s original settings.
Stability Lever
Soft Touch Dock for iPod and iPhone
Power/Pairing Indicator
Pairing
Press to pair the wireless
subwoofer to the sound bar.
Wireless/Sub-In
Adjust to switch between wireless
input and the Subwoofer Input.
POWER
SOURCE
VOLUME
PAIRING
LINE IN
MIN MAX
ON
OFF
BASS LEVEL
SUB-IN
SUB-INWIRELESS
Subwoofer
Output
Composite
Video Output
Component
Video Output
Composite
Video Input (AV)
RCA Stereo
Audio Input
(Aux)
RCA Stereo
Audio Input (AV)
Bass Level
Turn to adjust the bass output on the wireless subwoofer.
Subwoofer Input
Power
Press to power the wireless subwoofer o or on.
Page 7
Customer Support: 1-888-999-4215 iLive 7
SOURCE
VIDEO
SLEEP
EQ
DISPLAY
VOLUME
MENU
MUTE
SHUFFLE
REPEAT
MO/ST
MEMORY
LIVE
CLOCK
TIMERMOVIE
USER TREBLE BASS
MUSIC
BBE
LEVEL
T
U
N
I
N
G
T
U
N
I
N
G
EQ
Press to switch between Rock,
Pop, Classic, Jazz, and Flat
preset equalizer modes.
Power
Press to power the sound
bar o and on.
Treble and Bass
Press and use the levels buttons
to adjust the treble or bass.
User
Press to set custom treble
and bass levels.
Memory
Press to save the current radio
station to a preset channel.
MO/ST
Press to switch between Mono
and Stereo FM radio modes.
Album, Chapter, and Playlist
Press to adjust the current
album, chapter, or playlist on
a docked iPod or iPhone.
Display
Press to view the time on the display.
Menu ( )
Press to move up and down
through menus on an iPod or
the iPod app on an iPhone.
Skip/Search ( )
Press to skip between tracks
or press and hold to search
through the current track on
a docked iPod or iPhone.
Level
In user mode, press to adjust
the treble and bass.
Source
Press to switch between FM, iPod, Aux, AV, and Line modes.
Mute
Press to mute the volume.
Timer
With the power o, press to set a timer to turn the sound bar on to iPod or FM mode at a specied time. With the power o, press and hold to activate or deactivate the set timer.
Clock
With the power o, press to set the clock.
Sleep
Press repeatedly to set a sleep timer to turn the sound bar o after a set amount of time has passed.
Video
In AV mode, press to switch between Component Video Output and Composite Video Output.
Repeat
Press to set the repeat options on a docked iPod or iPhone.
Shue
Press to set the shue options on a docked iPod or iPhone.
Menu
Press to switch between menus on a docked iPod or the iPod app on an iPhone.
Select ( )
Press to make selections on a docked iPod or the iPod app on a docked iPhone.
Volume
Press to adjust the volume.
BBE Live, Music, and Movie
Press to switch to the
BBE Live, Music, and Movie audio modes.
Play/Pause
Press to play or pause a docked iPod or iPhone.
Page 8
iLive8
iPod and iPhone
1. Press the top right corner of the Soft Eject iPod Door to access the Dock for iPod and iPhone.
2. Swing the Stability Lever down to stabilize the sound bar while docking an iPhone or iPod.
3. Locate the numbered bracket that ts the iPhone/iPod model that will be docked.
Each included bracket has a number on it, indicating which iPhone/iPod model that bracket is compatible with. See the separate bracket chart page to identify which bracket is needed.
4. Snap the bracket into place over the iPhone/iPod connector in the Dock for iPod and iPhone.
5. Connect your iPod or iPhone to the connector inside the Dock for iPod and iPhone.
When the sound bar is plugged in, using AC power, the docked iPod or iPhone will charge.
1. Follow the instructions for Docking an iPod or iPhone.
2. Press the Power button to turn the sound bar on.
3. Press the Source button to switch to iPod mode.
4. Press the Play/Pause button to begin playing music from the docked iPhone or iPod.
Docking an iPod or iPhone
Playing a Docked iPod or iPhone
Stability Lever
Page 9
Customer Support: 1-888-999-4215 iLive 9
App
1. Go to the App Store on your iPhone, iPod touch, or on iTunes.
2. Search for MIP659D
3. Download the App.
When downloading directly from iTunes, sync the app to your iPod or iPhone from iTunes.
1. Follow the instructions for Docking an iPod or iPhone.
2. Once the iPod or iPhone is docked a screen will appear prompting you to download the MIP659D app from the App Store.
3. Press Yes to automatically download the MIP659D app.
Manually Downloading the App Automatically Downloading the App
CLOCK & CALENDAR
The clock and calendar will automatically sync with the time on the iPod or iPhone, so there’s no need to set it.
ALARM
Add as many alarms as you like using the settings menu. You can set them to wake to iPod music or Nature Sounds.
WEATHER
Type in your location and view your current weather conditions along with the time on the home page of the app.
PHOTO SLIDE SHOW
Select photos that are already on your iPod or iPhone and play a slideshow with your music in the background.
FM RADIO
While docked on the bar speaker, use the Dock + App to tune the FM radio and save FM radio station as presets.
SOURCES
When docked with the bar speaker you can use the Dock + App to switch between FM Radio, iPod, and Line Input modes.
MIP659D Features
Page 10
iLive10
1. Press the Power button to turn the power o.
2. Press the Clock button on the remote.
The hour on the display will begin blinking.
3. Press the Skip/Search buttons on the remote to adjust the hour.
4. Press the Clock button.
The minute on the display will begin blinking.
5. Press the Skip/Search buttons on the remote to adjust the minute.
6. Press the Clock button to nish setting the clock.
1. Press the Power button to turn the power on.
2. Press the Sleep button repeatedly to set the sleep timer.
3. After the set sleep time has expired, the sound bar will automatically power o.
Set the sleep time to “00” to turn the sleep timer o.
1. Press the Power button to turn the power o.
2. Press the Timer button on the remote.
The hour on the display will begin blinking.
3. Press the Skip/Search buttons on the remote to adjust the hour.
4. Press the Timer button.
The minute on the display will begin blinking.
5. Press the Skip/Search buttons on the remote to adjust the minute.
The source on the display will begin blinking.
6. Press the Skip/Search buttons on the remote to switch between iPod and FM modes.
7. Press the Timer button to nish setting the timer.
After the set time is reached, the sound bar will automatically power on to the set source.
1. Press the Power button to turn the power o.
2. Press and hold the Timer button to activate or deactivate the timer.
The letter “T” will appear on the display when the timer is activated.
Setting the Clock
Setting the Sleep Timer
Setting the Timer
Activating the Timer
FM Radio, Clock, Sleep Timer, and Timer
Adjust the built-in FM wire antenna to improve FM radio reception.
1. Press the Power button to turn the sound bar on.
2. Press the Source button to switch to FM radio mode.
3. Press the Tuning buttons on the remote to tune the FM radio.
1. Press the Power button to turn the sound bar on.
2. Press the Source button to switch to FM radio mode.
3. Press the Menu ( ) buttons on the remote to cycle through saved radio stations.
1. Follow the instructions for Tuning the FM Radio.
2. After tuning to the desired station, press the Memory button on the remote.
3. Press the Menu ( ) buttons on the remote to select a preset channel.
4. Press the Memory button to save the current radio station to the selected preset.
Up to 20 stations can be saved to the sound bar’s memory.
FM Antenna
Tuning the FM Radio
Listening to a Saved Radio Station
Saving a Radio Station
Page 11
Customer Support: 1-888-999-4215 iLive 11
Wireless Subwoofer Setup
While the wireless subwoofer was paired at the factory to allow for immediate operation, it will occasionally become un-paired in transit. Un­pairing can also occur in day-to-day operation due to dierent environmental inuences. This is normal. Should this occur, please follow the pairing instructions below.
1. Plug the sound bar into a power source and press the Power button to power the sound bar on.
2. Plug the wireless subwoofer into a power source and press the Power switch to power the wireless subwoofer on.
3. Press and hold the Pairing button on the wireless subwoofer until the Power/ Pairing Indicator begins to blink.
4. While the Power/Pairing Indicator on the wireless subwoofer is blinking, press and hold the Pairing button on the sound bar.
The Power/Pairing Indicator will remain lit once the sound bar and wireless subwoofer has been paired.
After pairing, the wireless subwoofer may take up to 30 seconds to begin playing audio from the sound bar.
Pairing allows the sound bar to recognize a wireless subwoofer. Once a wireless subwoofer is paired, the sound bar will transmit audio to it.
Once paired, the wireless speaker can be moved up to 200ft (line-of-site) or up to 90ft (indoors) depending on environmental conditions. Should the sound drop or become garbled it will be necessary to move the wireless subwoofer to another location in order to receive the signal clearly.
Important Note Pairing the Wireless Subwoofer
What does it mean to pair?
Additional Information
Link Indicator System Status
OFF Powered o
SLOW FLASHES Standby mode
QUICK FLASHES Attempting to pair
SOLID LIGHT Paired and playing
Page 12
iLive12
DVD PLAYER
DIGITAL CABLE or SATELLITE TUNER
VCR
GAMING CONSOLE
WIRELESS
SUBWOOFER
TELEVISION
WIRELESS
AUDIO
Basic Connectivity
This is a basic ow chart of how you can connect your home entertainment devices to the sound bar, and in turn how the sound bar connects to them.
For optimal performance, always connect video sources such as a DVD players, gaming consoles or set-top boxes directly to your television.
Page 13
Customer Support: 1-888-999-4215 iLive 13
Video and Audio Inputs/Outputs
For optimal performance, always connect video sources such as a DVD players, gaming consoles or set-top boxes directly to your television.
1. Connect an RCA cable (included) to the Composite Video Input (AV) and a video source.
2. Follow the instructions for Using a Composite Video Output or Using the Component Video Output
3. Follow the instructions for Using the RCA Audio Inputs (AV).
4. Press the Power button to turn the sound bar on.
5. Press the Source button to switch to AV mode.
6. Use the native controls on the connected video device to control video that runs through the sound bar.
1. Connect an RCA cable (included) to the Composite Video Output and a television.
2. Adjust the connected television to the proper input setting.
3. Press the Video button on the remote to switch between Composite and Component video output modes.
4. Video from a docked iPhone/iPod, or a connected DVD player can now be played through the sound bar to the connected television.
The Component Video Output will only output video from a docked iPod or iPhone. It cannot output video from the composite video input.
1. Connect a component video cable (not included) to the Component Video Output and a television.
2. Adjust the connected television to the proper input setting.
3. Press the Video button on the remote to switch between Composite and Component video output modes.
4. Video from a docked iPhone/iPod, or a connected DVD player can now be played through the sound bar to the connected television.
Using the Composite Video Input (AV)
Using the Composite Video Output
Using the Component Video Output
1. Connect a 3.5mm Audio Input cable (not included) to the 3.5mm Audio Input on the sound bar and an audio source.
2. Press the Power button to turn the sound bar on.
3. Press the Source button to switch to Line mode.
4. Use the native controls on the connected audio device to begin playing music through the connected sound bar.
1. Use an RCA cable (included) to connect an external subwoofer to the Subwoofer Output.
2. When audio is played through any source, the sound bar will automatically use the connected subwoofer.
1. Connect an RCA cable (included) to the RCA Audio Input (AV) on the sound bar and an audio source.
2. Press the Power button to turn the sound bar on.
3. Press the Source button to switch to AV mode.
4. Use the native controls on the connected audio device to begin playing music through the connected sound bar.
1. Connect an RCA cable (included) to the RCA Audio Input (Aux) on the sound bar and an audio source.
2. Press the Power button to turn the sound bar on.
3. Press the Source button to switch to Aux mode.
4. Use the native controls on the connected audio device to begin playing music through the connected sound bar.
Using the 3.5mm Audio Input
Using the Subwoofer Output
Using the RCA Audio Input (AV)
Using the RCA Audio Input (Aux)
Page 14
iLive14
Professional Audio Modes
Your favorite programming becomes more vibrant and engaging as BBE Live reveals all the detail and character of voices, ambient sounds and music -­even at low volume. Experience live sports and video games like you’ve never heard them before. Imagine hearing the crack of a bat, the shriek of a race car, the ricochet of gunre with BBE Live -- it’s like being there!
Press the BBE Live, Music, and Movie buttons on the
remote to switch between BBE Live, Music, and Movie audio modes.
Imagine what it sounds like to be on stage or in the studio with your favorite musical artist -- hearing and feeling the raw emotion of vocals, the crunch of guitars, the impact of percussion. BBE music integrates the same professional, proprietary harmonic restoration technology used in renown concert halls and recording studios to restore lost details of compressed music -- for sound quality closer than ever before to the original performance.
With BBE Movie, you’ll nally get audio quality that’s on par with today’s HD picture quality. From massive explosions to the faintest whisper, today’s 3D movies feature more complex soundelds than ever before. That’s why BBE Movie incorporates proprietary BBE HD-3D Sound technology to reveal more of the delth and space engineered into the audio mix. Whether it’s the latest blockbuster or a favorite classic, BBE Movie reveals sonic details you may never have heard before.
Live
Using BBE Professional Audio Modes
Music
Movies
Page 15
Customer Support: 1-888-999-4215 iLive 15
Mounting to a Wall
We recommend having this sound bar professionally mounted.
The included spacers should be used at your discretion to extend the face of the sound bar farther from the wall. These are typically used when mounting the sound bar under a television, and the face of the sound bar needs to be ush with the face of the television.
1. Use the Tape Measure to decide how high you’d like to hang the sound bar on the wall.
2. The sound bar must be hung within 6 feet of an AC power outlet for the attached AC power cable to reach.
3. Use the Stud Finder to locate 2 parallel wooden studs to screw the mounting brackets into.
4. Mark the wall at the center of the studs using the Pencil.
5. Line the Level up on both of your marks to make sure they are level. If they’re not, adjust the marks as needed to make them level.
6. After you’ve double checked your markings, drill through the top hole on both mounting brackets directly into the marks you’ve made on the wall.
7. If you are using the brackets only and no spacers, use the included short screws. If you are using any of the spacers or combination of the spacers, use the long screws.
8. Use the Level to level each of the hanging brackets, then drill the second screw into the bottom hole on both mounting brackets.
9. Slide the sound bar onto the mounting brackets, and make sure there is a rm and stable connection before letting go of the sound bar.
10. Finally, use the Level to conrm that the sound bar is level.
Manual or Power Screwdriver
Stud Finder
Pencil
Tape Measure
Level
(2) Wall Mount Brackets
(4) Long Screws
(2) 1/2” Spacers
(2) 3/4” Spacers
Important Notes
Getting Started
Required Tools
Included Hardware
16”
ITPW891B
ITPW891B
screws
studs
mounting
bracket
spacer
Page 16
Copyright © 2011 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice
To download this User’s Guide in English, Spanish, or French, visit the support section at www.ilive.net.
Para transferir esta guía de usuario en inglés, español, o francés, visite la sección de la ayuda en www.ilive.net.
Pour télécharger ce guide de l’utilisateur en anglais, espagnol, ou français, visitez la section de soutien chez www.ilive.net.
Phone: 1-888-999-4215 Email: customerservice@ilive.net Parts Email: partsinfo@dpi-global.com Website: www.ilive.net
International Support
Contact Information
Company Information
Loading...