Ilive ITB382B User Manual

Download

USER’S GUIDE

V: 573-01

ITB382B

Bluetooth 37” HD Sound Bar with Built-in Subwoofer

For the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com

Warnings and Precautions

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.

AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité.

CAUTION: Use of any controls or adjustments or performance of procedures other than those herein specied may result in hazardous radiation exposure.

WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface.

WARNING: Use of this unit near uorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any uorescent lighting, as it may be the cause.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION

RISQUE D' ÉLECTROCUTION

NE PAS OUVRIR

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

PRÉCAUTION: Danger d’explosion si les piles sont remplacées de façon incorrect. Remplacer les piles seulement par le même type de pile ou l’équivalent.

WARNING: The battery, batteries, and battery pack shall not be exposed to excessive heat such as sunshine, re, or the like.

WARNING: Lithium batteries, like all rechargeable batteries are recyclable and should be recycled or disposed of in normal household waste. Contact your local government for disposal or recycling practices in your area. They should never be incinerated since they might explode.

WARNING: Shock hazard - Do Not Open.

AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR

Mains Plug or Direct plug-in adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the Mains Plug or Direct plug-in adapter should be disconnected from the mains socket outlet completely.

La che d’alimentation ou adaptateur de courant est utilisé comme dispositif de déconnexion et doit rester accessible pendant l’utilisation. Pour mettre l’appareil hors tension, la che ou adaptateur de courant doit être débranché de la prise de courant.

Important Safety Instructions

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12.

Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Special note: When placing your unit on a lacquered or natural nish, protect your furniture with a cloth or other protective material.

FCC Warnings

WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Additional Warnings

The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed on apparatus.

L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.

Battery shall not be exposed to excessive heat such as sunshine, re or the like.

Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la lumière du soleil, au feu ou autres choses de semblable.

Caution marking is located at the rear or bottom of the apparatus.

Attention marquage est situé sur le paneau arrière ou inférieur de l’unité.

The marking information is located at the rear or bottom of apparatus.

Le marquage est situé sur le paneau arrière ou inférieur de l’unité.

This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts.

Customer Support: 1-888-999-4215 3

ITB382B

Features

• 37” length

• Supports Bluetooth v2.1

• Supports prole A2DP (Advanced Audio Distribution Prole)

• Digital volume control

• FM Radio (PLL)

• Remote

• Learning remote control capability

• Bass controls

• Treble controls

• Preset EQ

• Optical digital audio input

• 3.5mm audio input

• Subwoofer output

• Stereo RCA audio inputs

• LED pairing indicator

• LED source indicators

• LED power indicator

• Wall mountable

• Wireless range: 33 feet

Setup

Power Remote

AC power input: requires an AC/DC power adapter (included)

Requires a CR2025 battery (pre-installed)

• AC power input: requires an AC/DC power adapter (included)

Includes

• Remote control: requires a CR2025 battery (pre-installed)

• RCA stereo audio cable

• Wall-mount hardware and instructions

• AC/DC power adapter

LED Indicators

Status Indicator

Power O No Light

Optical Mode Amber Light

Aux In Mode White light

Line In Mode White Light

Radio Mode Green Light

OPEN

PUSH

CR 2025

LITHIUM BATTERY

CR2025

18V

CR 2025

LITHIUM BATTERY

OPEN

PUSH

Mounting

We recommend having this bar speaker professionally mounted.

Bluetooth Ready Flashing Blue Light

Bluetooth Connected Blue Light

Table of Contents

Warnings and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

ITB382B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Power LED Indicators Remote Mounting Includes

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Audio Inputs & Subwoofer Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Using the Stereo RCA Inputs Using the Optical Input Using the Subwoofer Output

Radio and Line In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Tuning the Radio Using the Line In

Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Pairing a Bluetooth Device for the First Time Playing Audio Wirelessly

Learn Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Understanding the Learn feature Using the Learn Feature

Company Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

International Support Contact Information Warranty Green Initiative

Customer Support: 1-888-999-4215 5

Introduction

18V

Subwoofer Output Stereo RCA Audio Inputs

FM Antenna

Optical Input

Power

Press to turn the unit on or o.

Volume

Press to adjust the

volume up or down.

Line Input

POWER

VOLUME

LINE IN

SOURCE

LEARN

PAIRING

Source

Press to switch between Optical, Line In/AUX, Bluetooth, and FM Radio modes.

Learn

Press to begin using the learn function.

Pairing

Press to begin pairing with a Bluetooth device.

Power

Press to turn the

unit on or o.

Aux/Line

Press to switch to Line In/AUX mode.

Optical

Press to switch to

Optical mode.

Press to switch to

Bluetooth Mode.

Scan

Press to scan for

available radio stations

in FM Radio mode.

Music

Press to switch to the EQ

optimized for music.

Treble

Press to adjust the

treble up or down.

Bass

Press to adjust the

bass up or down

AUX/ LINE

Mute

Press to mute the volume.

Press to switch to FM Radio mode.

Channel +/-

Press to adjust the channel up or down.

Voice

Press to switch to the EQ optimized for dialogue.

Movie

Press to switch to the EQ optimized for movie sound.

Volume

Press to adjust the volume.

Customer Support: 1-888-999-4215 7

Audio Inputs & Subwoofer Output

18V

Using the Stereo RCA Inputs

When connecting two products using an RCA Cable, match the colored ports with the same colored connection.

Before use, disconnect any cables connected to the Line In.

1. Connect the RCA Cable to the RCA Stereo Inputs located on the back of the unit, and to the audio outputs on the television.

2. Press the Power button to power on the unit.

3. Press the Source button repeatedly to enter Aux/Line Mode, indicated by a white light.

4. Audio played through the television will now be heard through the speakers.

Using the Optical Input

You will need: An audio source with an Optical Audio Output and a Digital Optical Audio Cable (not included)

1. Connect the Digital Optical Audio Cable to the optical output on the audio source and to the Optical Input on the speaker bar.

2. Press the Power button to power the unit on.

3. Press the Source button repeatedly to switch to SPDIF Mode, indicated by an amber light.

4. Using the native controls on your connected device, make sure the audio settings are set to PCM or Optical Audio and are turned On.

5. Audio from the connected audio source will now be played through the speakers.

Using the Subwoofer Output

1. Use an RCA cable (included) to connect an external subwoofer to the Subwoofer Output.

2. When audio is played through any source, the bar speaker will automatically use the connected subwoofer.

Radio and Line In

Tuning the Radio

1. Press the Source button repeatedly to enter FM Radio Mode, indicated by a green light.

2. Press the Scan button on the remote.

3. The bar speaker will scan for all available stations, and store them.

4. Press the Channel +/- buttons to browse through stored stations.

Using the Line In

1. Plug one end of a 3.5 mm audio input cable into the Line In on the unit.

3.5 mm audio input cable not included.

Before use, disconnect any cables connected to the Stereo RCA Inputs.

2. Plug the other end of the cable into the audio output/headphone output on an MP3 Player or other audio source.

3. Press the Power button to power the unit on.

4. Press the Source button repeatedly to enter Aux/Line In Mode, indicated by a white light.

5. Audio played through the connected device will now be heard through the speakers.

Customer Support: 1-888-999-4215 9

Bluetooth

Playing Audio WirelesslyPairing a Bluetooth Device for the First Time

1. Power on the unit by pressing the Power button.

2. Press the Source button repeatedly to enter Bluetooth mode, indicated by a blue light.

3. Press the Pairing button on the side of the unit.

The Pairing Indicator will ash blue quickly.

When pairing, remain within 3 feet of the unit.

4. Using the native controls on your Bluetooth device, select the “ITB382” in your Bluetooth settings to pair.

If your device requests a password, enter the default password “ 0 0 0 0 ”.

Refer to the user’s manual for your specic device for instructions on pairing and connecting Bluetooth devices.

5. When successfully paired and connected, a beep will issue from the unit and the Pairing Indicator will display a solid blue light.

After initial pairing, the unit will stay paired unless unpaired manually by the user or erased due to a reset of the device.

1. Follow the instructions for Pairing a Bluetooth Device.

2. Press the BT button on the remote to switch to Bluetooth Mode.

3. Use the native controls on the connected Bluetooth Device to select a track.

4. To play, pause or skip the selected track, use the native controls on the connected Bluetooth Device.

5. Audio played through the connected Bluetooth device will now be heard through the speakers.

If your device should become unpaired or you nd it is unable to connect, repeat the above steps.

Note: Holding the Pair button for more than 3 seconds will erase all stored Bluetooth devices from the sound bar’s memory. After the devices have been erased, to re-pair with the unit you must also forget the ITB382 on your Bluetooth device and then follow the steps above.

Learn Feature

Understanding the Learn feature

What is the Learn feature?

The Learn feature captures remote commands from your television remote, and teaches your bar speaker to operate when these commands are pressed. Power, volume and mute are a few examples of commands that the bar speaker can learn.

Why use the Learn feature?

Teaching the bar speaker remote commands will reduce the number of remotes needed, save time searching for remote codes, and improve the ease of operation.

Using the Learn Feature

1. With the power O, press the Learn button on the unit.

An indicator will icker red.

2. Press the button you desire to be learned on the included remote.

For example: Volume+

The red light will continue to icker, and another indicator will display a blue light.

3. Press the corresponding button on your remote.

The red light will continue to icker, and another indicator will display a green light.

4. Press the Learn button on the unit.

5. The programmed button on your remote will now be able to control your sound bar.

Note: It is necessary to program each button i.e. channel and volume + and - separately.

To start over, press and hold the learn key for over 3 seconds. If the sound bar has failed to learn a command, all the LED indicators will display a light for two seconds to signal the learning function has been reset.

Note: Not all functions of the sound bar will be available through your own remote control, such as bass and treble. Use the included remote for these functions.

Note: While ITB382B is able to learn most IR protocols, not all can be programmed.

Customer Support: 1-888-999-4215 11

Ilive ITB382B User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual