CLOCK SET
ALARM SET
DC IN
LINE IN
FM ANT.
USER’S GUIDE
V: 820-01
CLOCK SET
ALARM SET
DC IN
LINE IN
FM ANT.
RADIO LINE IN
POWER SOURCE MEMORY PAIR / SCAN TUNE +
VOLUME
ALARM
LIGHT TUNE –
ON
OFF
Pair/Scan
Press to begin pairing.
In FM radio mode, press
and hold to scan through
all available radio stations
and set them as presets.
Memory
In FM radio mode, press
and hold to begin setting
a station as a preset.
Press to cycle through
preset stations.
Tune +/-
Press to tune the radio
in FM Radio Mode.
Press and hold to
search for the next
available frequency.
Source
Press to switch
between Bluetooth,
FM Radio, and Line In
modes.
Light
Press to turn the clock
face light on or off.
Volume
Press to adjust the
volume.
Power
Press to turn the unit
on and off.
Alarm On/Off
Press to turn the
alarm on or off.
Alarm Set
Press in and hold
to begin setting the
alarm.
Clock Set
Press in and hold
to begin setting the
analogue clock.
Line In
Line In
Indicator
Radio
Indicator
Pair
Indicator
Micro USB
Charging Port
ICB263B Bluetooth Speaker with Clock
Warning: Changes or modications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The apparatus shall not be exposed to dripping or splashing and that no objects lled with
liquids, such as vases, shall be placed on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne
contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.
• Main plug is used as disconnect device and it should remain readily operable during intended
use. In order to disconnect the apparatus from the mains completely, the mains plug should
be disconnected form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant son
utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être
débranchée du secteur.
• Battery shall not be exposed to excessive heat such as sunshine, re or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la lumière du soleil, au feu
ou autres choses de semblable.
• Caution marking is located at the rear or bottom of the apparatus.
Attention marquage est situé sur le paneau arrière ou inférieur de l’unité.
• The marking information is located at the rear or bottom of apparatus.
Le marquage est situé sur le paneau arrière ou inférieur de l’unité.
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The
wide blade or the third prong are provided for your
safety. When the provided plug does not t into your
outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the
manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table
specied by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over. Unplug this apparatus during lightning
storms or when unused for long periods of time.
13. Refer all servicing to qualied
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has
been exposed to rain or moisture,
does not operate normally, or has
been dropped.
• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
• WARNING:To reduce the risk of re or electric shock, do not expose this apparatus to rain or
moisture.
• AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet
appareil sous la pluie et l’humidité.
• CAUTION: Use of controls or adjustments or performance of procedures other than those specied
may result in hazardous radiation exposure.
• WARNING: Changes or modications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
• WARNING: Do not place this unit directly onto furniture surfaces with any type of soft, porous, or
sensitive nish. As with any rubber compound made with oils, the feet could cause marks or staining
where the feet reside. We recommend using a protective barrier such as a cloth or a piece of glass
between the unit and the surface to reduce the risk of damage and/or staining.
• WARNING: Use of this unit near uorescent lighting may cause interference regarding use of
the remote. If the unit is displaying erratic behavior move away from any uorescent lighting, as
it may be the cause.
• CAUTION:Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type.
• PRÉCAUTION: Danger d’explosion si les piles sont remplacées de façon incorrect. Remplacer les
piles seulement par le même type de pile ou l’équivalent.
• WARNING: There is a danger of explosion if you attempt to charge standard Alkaline batteries in
the unit. Only use rechargeable NiMH batteries.
• WARNING: The remote control’s button cell battery contains mercury. Do not put in the trash,
instead recycle or dispose of as hazardous waste
• WARNING:Lithium batteries, like all rechargeable batteries are recyclable and should be recycled
or disposed of in normal household waste. Contact your local government for disposal or recycling
practices in your area. They should never be incinerated since they might explode.
• WARNING: Shock hazard - Do Not Open.
• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR
Mains plug is used as disconnect device and it should remain readily operable during intended
use. In order to disconnect the apparatus from the mains completely, the mains plug should be
disconnected form the mains socket outlet completely.
La prise du secteur est utilisé pour déconnecter le système.
La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant son
utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être
débranchée du secteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
No mezcle baterías viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.).
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
This symbol indicates that this product
incorporates double insulation between hazardous
mains voltage and user accessible parts.
The lightning ash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufcient magnitude to constitute a risk of
electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS
Introduction and Setup
FCC Warnings
Power
The battery backup is intended for short
power outages only. The clock radio’s primary
functions cannot run off of the battery backup
alone.
Requires 2, AA-size, batteries (not included)
UM-3/R6/SIZE AA, 1.5V
UM-3/R6/SIZE AA, 1.5V
Battery Backup
Additional Warnings
WARNINGS AND PRECAUTIONS
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com Customer Service: 1-888-999-4215
Email Support: prodinfo@dpiinc.com, Email Parts: partsinfo@dpiinc.com
Copyright © 2013 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice..
The Bluetooth word mark and logos are owned by the Bluetooth SIG.
Plug one end of the included USB cable and
adapter into the Micro USB Port on the unit
and an AC power outlet to power the dock.
1. Press and hold in the Alarm Set knob.
2. While holding in the Alarm Set knob,
adjust to the desired time by turning the
knob.
3. Release the Alarm Set knob when
nished selecting the desired time.
4. Press the Alarm On/Off button to turn the
alarm on and nish setting the alarm.
5. Once the set alarm time is
reached, the alarm will sound.
1. Press the Power/Sleep button
to turn the clock radio on.
2. Press the Source button to
switch to FM radio mode.
The Radio Indicator will light up.
3. Press the Tun+ and Tun-buttons to adjust
the radio to the desired frequency.
4. Press and hold the Tun+ and Tun- buttons
to search for the next available frequency.
5. Press the Vol+/- buttons to
adjust the volume.
Alarm
Radio
Setting the Alarm
1. Follow the instructions for
Setting the Alarm.
2. Press the Alarm On/Off button until
the alarm is in the off position.
Cancelling the Alarm
1. Press and hold in the Clock Set knob.
2. While holding in the Clock Set knob,
adjust to the desired time by turning the
knob.
3. Release the Clock Set knob when nish
setting the time.
Setting the Analogue Clock
Tuning the FM Radio
1. Follow the instructions for
Tuning the FM Radio.
2. Tune to the desired station.
3. Press and hold the Memory button.
4. Press the Tun+/- button to adjust
to the desired preset number.
Up to 20 stations may be saved as presets.
5. Press the Memory button to save the
current radio station as a preset.
Saving a Station as a Preset
1. Follow the instructions for Tuning the
Radio and Saving a Station as a Preset.
2. Press the Memory button to cycle
through preset radio stations.
Tuning to a Preset Radio Station
Adjust the position of the FM Antenna
to improve FM radio reception.
Radio Reception
To download this User’s Guide in English,
Spanish, or French, or to get answers to
frequently asked questions, visit the support
section at: www.iLiveElectronics.com
Para descargar este Manual del
Usuario en inglés, español y francés, o
para obtener respuestas a preguntas
frecuentes, visite la sección de apoyo
en www.iLiveElectronics.com
Pour télécharger ce guide de l’utilisateur
en anglais, espagnol ou français, ou pour
obtenir des réponses à des questions
fréquemment posées, consultez la rubrique
d’assistance sur www.iLiveElectronics.com
International Support
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com Customer Service: 1-888-999-4215
Email Support: prodinfo@dpiinc.com, Email Parts: partsinfo@dpiinc.com
Copyright © 2013 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice..
The Bluetooth word mark and logos are owned by the Bluetooth SIG.
Requires a 3.5mm audio cable (not included)
1. Connect a 3.5mm audio cable to the
Line In on the unit and an audio output
on an MP3 player or other audio source.
2. Press the Source button to
switch to Line In mode.
The Line In Indicator will light up.
3. Use the native controls on the
connected MP3 player or other audio
source to play and control audio
played through the clock radio.
Line In
Using the Line In
Clock
CLOCK SET
ALARM SET
DC IN
LINE IN
FM ANT.
Bluetooth Setup
Pairing a Bluetooth Device for the First Time
1. Power on the unit by pressing the Power
button.
2. Press the Source button repeatedly to
switch to Bluetooth mode.
3. Press the Pair button.
The Pairing Indicator will ash blue
quickly.
When pairing, remain within 3 feet of the
unit.
4. Using the native controls on your
Bluetooth device, select the “ICB263” in
your Bluetooth settings to pair.
If your device requests a password, enter
the default password “ 0 0 0 0 ”.
Refer to the user’s manual for your specic
device for instructions on pairing and
connecting Bluetooth devices.
5. When successfully paired and connected,
the Pairing Indicator will display a solid
blue light.
After initial pairing, the unit will stay paired
unless unpaired manually by the user or
erased due to a reset of the device.
If your device should become unpaired or
you nd it is unable to connect, repeat the
above steps or press the Pair button to
start the pairing process pairing again.
Loading...