IKUSI ELECTRONICA S L TR2400-MCX Installation Manual

CATEGORIA DE DOCUMENTO

Preparado por / Prepared by

No. / Num.

Pág. / Page

Luis Vidaurreta

1 / 4

Aprobado por / Approved by

Fecha / Date

Rev./ Rev.

Archivo / File

17/10/2017

PVTTR2400 installation

manual.docx

TIPO DE DOCUMENTO

PVTTR2400-MCX INSTALLATION MANUAL

1. SYSTEM DESCRIPTION

The module PVTTR2400-MCX has been designed and manufactured by IKUSI-Angel
Iglesias S.A. to be included in its radio remote control equipment.
The module PVTTR2400-MCX is a radio wireless for the frequency band 2405MHZ to
2475MHZ.
The module PVTTR2400-MCX is supplied with two smd antennas for antenna diversity.

2. SAFETY INSTRUCTION

These instructions must be read carefully in order to install and use the set properly and to keep it in
perfect working condition and to reduce the risks of misuse.
Do not use this set on machines in potentially explosive atmospheres, except the models certified
ATEX/RATEX designed to work in that type of environments.
Any use other than that specified in this manual is dangerous. The following instructions must be
strictly adhered to.

4.1 - WHAT YOU MUST DO

Strictly adhere to the instructions for installation contained in this manual
Make sure that professional and competent personnel carry out the installation.
Ensure that all site and prevailing safety regulations are fully respected.
Make sure that this manual is permanently available to the operator and maintenance personnel.
Keep the transmitter out of reach of unauthorised personnel.
On starting each working day, check to make sure that the STOP button and other safety measures are

working.

When in doubt, press the STOP button.
Whenever several sets have been installed, make sure the transmitter you are going to use is the right

one. Identify the machine controlled on the label for this purpose on the transmitter.

Service the equipment periodically.
When carrying out repairs, only use spare parts supplied by IKUSI dealers.

4.2 - WHAT YOU MUST NOT DO

Never make any changes to the set, which have been studied and approved by manufacturer.
Never power the equipment other than with the specified power supply.
Never allow unqualified personnel to operate the equipment.
After use, never leave the equipment ON (one or several transmitters). Always set the contact key and

the STOP button to switch off position of the equipment to avoid accidentally to activate manoeuvres –
specially in crane maintenance purposes-.

Do not use the set when visibility is limited.
Avoid knocking or dropping the set.
Do not use the set if failure is detected.

Changes or modifications not expressly approved by IKUSI could void the user’s authority to operate this
equipment.

CATEGORIA DE DOCUMENTO

Preparado por / Prepared by

No. / Num.

Pág. / Page

Luis Vidaurreta

2 / 4

Aprobado por / Approved by

Fecha / Date

Rev./ Rev.

Archivo / File

17/10/2017

PVTTR2400 installation

manual.docx

Frequency band

Antenna Gain [dBi]

2.4 GHz

13.79

TIPO DE DOCUMENTO

3. INSTALLATION

Make sure that the crane is stopped for the entire duration of the assembly process, keep the work area free
and wear protective clothing.
Park the crane and position stop-ends (if these are not available use appropriate signs) at a suitable distance
so that other cranes on the same runway do not hit it.
Check the power-supply voltage and turn off the mains switch, disconnecting the wiring and connector
between the receiver and the electrical cabinet of the machine.
Remember that the receiver has several voltage-powered circuits. Even when the power has been cut off,
there is still a risk of electrical shocks.

4. FCC/ISED REGULATORY NOTICES

Modification statement

IKUSI ELECTRONICA, S.L. has not approved any changes or modifications to this device by the

user. Any changes or modifications could void the user’s authority to operate the equipment.

IKUSI ELECTRONICA, S.L. n’approuve aucune modification apportée à l’appareil par l’utilisateur,

quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation
de l’appareil par l’utilisateur.

Interference statement

This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Wireless notice

This device complies with FCC/ISED radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS‐102 of the ISED

radio frequency (RF) Exposure rules. Antenna gain must be below:

This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

This device needs to be installed and used on distance greater than 20 cm from human body.