Ikelite S5 IS User Manual

Download

Ikelite Digital Housing

Lens Po r t

oom

acro/ Manual F

ocus

lash

Pop-Up Flash

ode

Continous

FRONT VIEW

Lid

Snap

uick Release

Button

Rubber H

andles

Tray

ase

Shutter Release

BACK VIEW

ode

Function

ISO

isplay

ovieShortcut

TTL Sync Cord Connector

Omni Selector

O'ring

Set

Shutter Release

Snap

Lid

nap

TOP VIEW

Lens Po r t

Zoom

Macro/ Manual Focus

TTL Sync Cord

Connector

Flash

Pop-Up Flash

Mode

Continous

Off

Mode

Shutter Release

Lift

Push For ward

Lid Snap Lock

Lid Hook

O' Ring

Housing Back

Mounting Bolt

Mounting Tray

i n s t r u c t i o n m a n u a l

#6140.05 for Canon PowerShot S5 IS

Congratulations on your purchase of an Ikelite Digital Camera Housing. Ikelite has over 30 years of experience in the underwater photographic and lighting market. Our products are designed and built in the USA by Ikelite for both the professional and amateur photographer. The clear housing permits instant visual inspection of the camera and all sealing surfaces as well as complete monitoring of controls and camera LCD screens. Ikelite Digital Housings are slightly negative in salt water for stability. This housing has been water pressure tested at the factory. Housing is pressure tested to 200’ (60m).

OOppeenniinngg tthhee HHoouussiinngg

1. Lid Snaps have a To open, push Lid Snap Lock forward and lift as shown. Keep pressure on the Lid Snap so it does not fly open quickly.

Some lid snaps have a lot of spring tension once they go over center, have a firm grip on the lid snap. Lid Snaps may be opened one at a time.

LLoocckk

IInnssttaalllliinngg tthhee CCaammeerraa

1. Remove the back from the housing. The mounting tray for the camera is secured to the housing back. Position the camera on the tray and secure it with the mounting bolt which threads into the camera’s tripod socket. UUssee aa ccooiinn oorr ffllaatt bbllaaddeedd ssccrreewwddrriivveerr ttoo ttiigghhtteenn tthhee mmoouunnttiinngg bboolltt ssoo tthhee ccaammeerraa iiss ffllaatt aaggaaiinnsstt tthhee ttrraayy..

CCAAUUTTIIOONN::

Some camera tripod socket threads are plastic. The mounting tray bolt is metal. Do not cross thread or over tighten as you may damage the camera tripod socket threads.

2. Pull out on each housing control until it stops. This will get the controls out of the way for installing the camera.

FFllaasshh CCoonnnneeccttiioonn ffoorr EExxtteerrnnaall SSttrroobbees

When using an external strobe connect the housings Hot Shoe Connector. Slide the connector into the hot shoe of the camera from the back of the camera as shown. Slide the connector forward until it stops. This should be done before the camera is secured with the mounting bolt.

External Strobe Connector Waterproof Cap (see caution)

O’ring

Housing Back

Silver

Mounting

Bracket

Silver

Mounting Bracket

Top Edge

of Housing

Hot Shoe

Hot Shoe Connector

CCaauuttiioonn:

Camera

DDoo nnoott rreemmoovvee tthhee EExxtteerrnnaall SSttrroobbee CCoonnnneeccttoorr’’ss wwaatteerrpprrooooff ccaap uunnlleessss aann eexxtteerrnnaall ssyynncc ccoorrdd iiss ggooiinngg ttoo bbee pplluuggggeedd iinn.

CClloossiinngg tthhee HHoouussiinngg

1. Place housing face down in your lap or on a flat surface.

2. Check to see that there is an o’ring on the housing back and that it is clean and in its proper location.

3. Guide the back onto the housing. The o’ring should touch the housing all the way around. There should be an even gap all the way

housing

around between the housing and the housing back.

4. Lift the lid snaps so they are extended and place the lid snap into the hook on the housing back.

5. To close the housing push down on the lid snaps until

even gap all 4 sides

they snap into place . Lid snaps on opposite sides of the housing should be closed at the same time. Be sure they are down

housing

far enough to engage the lock.

DDoouubbllee cchheecckk

- Once the housing is closed, check the o’ring seal. Check the gap between the housing back and the housing, it should be even all the way around.

Look through the clear plastic back at the o’ring. You should see

a darkened area where the o’ring is compressed against the housing back. If you do not see an even black compression seal all the way around the back, open the lid snaps, reseat the housing back and close the lid snaps. Visually check the seal again.

housing back

o’ring

housing back

o’ring

IIff yyoouu aarree nnoott uussiinngg tthhee EExxtteerrnnaall FFllaasshh CCoonnnneeccttiioonn

Store the hot-shoe by sliding it into the silver bracket located on the inside back of the camera housing as shown. This can be done after the camera is mounted to the mounting tray.

CCAAUUTTIIOON

OOnnllyy rreemmoovvee tthhee WWaatteerrPPrrooooff ccaapp ffrroomm tthhee eexxtteerrnnaall ssttrroobbe

ccoonnnneeccttoorr oonn tthhee bbaacckk ooff tthhee hhoouussiinngg wwhheenn aann eexxtteerrnnaall ssttrroobbe wwiillll bbee ccoonnnneecctteedd.

CChheecckkiinngg CCoonnttrroollss

Once the housing has been closed, push the controls back into

place. Make sure they line up with the camera’s controls.

TTuurrnn CCaammeerraa OOnn

Turn the camera on and operate each of the housing controls to get a feel for using the camera in the housing. Take a few pictures above water with the camera in the housing.

ZZoooomm CCoonnttrrooll

(NOTE:) After you have used the housing's zoom control it must be returned to the center position to disengage. If the housing zoom control is pushing the zoom lever in either direction you may not be able to take a picture or access any other function as the camera is receiving a signal from the engaged zoom control.

Zoom control engaged

Zoom control disengaged (centered)

LLuubbrriiccaannttss

1. Ikelite provides silicone lubricant with the housing. We recommend you use only Ikelite lubricant on Ikelite products as some other brands may cause the o’ring to swell and not seal properly.

2. Use only enough lubricant to lightly cover control shafts and o’rings. Wipe off any excess lubricant with a clean cloth. Lubricant is not a sealant, it is used to reduce friction. Excessive lubricant can collect sand and dirt which may interfere with proper sealing.

CCAAUUTTIIOONN

NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaan ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk.

LLeennss PPoorrt

The Lens Port is factory sealed, do not remove. Treat the glass in the lens port as a camera lens. After use, rinse and gently dry the lens port to avoid water spotting. To clean use a mild soap solution or lens cleaner.

Do not use alcohol or window cleaner on the Lens Port.

The Lens Port is threaded so that accessory lenses can be

crewed onto the port. The threads are very fine, take care not

s to cross thread accessory lenses. The housing port has a 67mm thread which accepts the optional #6420 Ikelite W-20 Wide-Angle Lens and other manufacturers

67mm) screw thread style lenses. These lenses can be screwed

( onto the lens port above or below water. These lenses are designed to have water between the front of the port and the accessory lens. Make sure no air bubbles are trapped between

he port and the accessory lens. There may be slight vignetting

t when these wide angle lenses are installed. Any vignetting that occurs can be eliminated by zooming the camera lens slightly. To properly light subjects when using a wide angle lens an external strobe should be used. Due to the wide coverage of the wide angle lenses, the DS125 Substrobe is recommended or two DS51 Substrobes.

Wide Angle Lens

UUssiinngg FFllaassh

UUssiinngg tthhee CCaammeerraa’’ss BBuuiilltt--iinn FFllaasshh..

If you do not have an external flash the camera’s built-in flash can be used. See Diffuser instructions.

DDiiffffuusseerr && DDeefflleeccttoorr IInnssttaallllaattiioonn

Diffuser

Housing shown with accessory wide angle lens.

DDiiffffuusseerr aanndd DDeefflleeccttoorr ccoonntt..

A diffuser and deflector are included with the housing. The diffuser is white transparent plastic. The deflector is also white but is not transparent.

To install the diffuser or deflector spread the port clamp at the spring end and slide over the lens port. The white plastic should be placed in front of the camera flash. The port clamp should be pushed back against the front of the housing.

Diffuser/Deflector

material

Port Clamp

Spring

Spread to Install

DDiiffffuusseerr

The diffuser should be installed when using the camera’s built in flash. When shooting with the camera’s built-in flash at approximately 2 feet (0.6 m) or less, zoom the lens to maximum telephoto. The lens port on the housing blocks a portion of the light from the camera’s built-in flash when shooting close up. If you do not zoom to maximum telephoto, a shadow may appear in the lower left corner of close-up photographs.

(You can test this above water)

DDeefflleeccttoorr

The deflector should be installed when using an external strobe such as the DS51 or DS125 Substrobe and DS Sensor. The deflector is required when using the camera’s built-in flash to trigger the EV Controller. The deflector will redirect the camera’s flash to the DS Sensor or EV Controller which controls the external strobe.

Housing shown with diffuser installed.

UUssiinngg EExxtteerrnnaall SSttrroobbeess

UUssiinngg TTTTLL FFllaasshh EExxppoossuurree wwiitthh EExxtteerrnnaall IIkkeelliittee DDSS SSuubbssttrroobbeess ((RReeccoommmmeennddeedd))

This housing has Conversion Circuitry built into the housing. When used with current model Ikelite DS Substrobes the Conversion Circuitry provides Canon eTTL flash exposure. In the TTL mode the camera controls the light output of the external strobe(s) to obtain properly exposed images. The Conversion Circuitry is powered by the Ikelite DS Substrobe when connected to the housing with the #4103.51 single or #4103.52 dual sync cords with a blue band. See page 13 for DS Substrobe compatibility with Conversion Circuitry.

UUssiinngg MMaannuuaall EExxppoossuurree wwiitthh EExxtteerrnnaall DDSS SSuubbssttrroobbeess

Any Ikelite DS Substrobe(s) can be used in the manual mode when connected with the #4103.51 single or #4103.52 dual sync cord with a blue band. In the manual mode different power settings on the DS Substrobe can be selected to obtain a properly exposed image.

UUssiinngg IIkkeelliittee NNoonn--DDSS SSuubbssttrroobbeess ((SSuubbssttrroobbeess 5500,, 110000AA,, 220000,, 440000)) wwiitthh tthhiiss hhoouussiinngg..

The Conversion Circuitry is automatically disabled when used with a Non-DS Substrobe. These Substrobes can be used in their manual mode utilizing any power settings provided on the Substrobe.

UUssiinngg NNoonn IIkkeelliittee SSttrroobbeess wwiitthh tthhiiss HHoouussiinngg

The Conversion Circuitry is automatically disabled when used with a Non Ikelite strobe. These strobes can be used in their manual mode utilizing any power settings provided on the strobe.

NNOOTTEE:: DDSS SSuubbssttrroobbee UUpp--ddaattee mmaayy bbee rreeqquuiirreedd.

ikelite

SubstrobeSubstrobe

MOD-NC

DDSS5500 SSuubbssttrroobbeess

DS50 SubStrobes with a Serial Number below 63,850 can not be

• updated to operate with the Conversion Circuitry.

• DS50 SubStrobes with a Serial Number between 63,850 and 69,999 operate with the Conversion Circuitry, but require update

o provide optimum performance.

• DS50 Substrobe with a Serial Number of 70,000 or higher or with one of the two following labels in the battery compartment provide optimum performance with the Conversion Circuitry.

DDSS112255 SSuubbssttrroobbeess

• DS125 Substrobes with a Serial Number below 2,500 must be updated to operate correctly with the Conversion Circuitry.

• DS125 Substrobes with a Serial Number between 2,501 and 4,900 operate with the Conversion Circuitry but require update to provide optimum performance.

• DS125 Substrobe with a Serial Number of 5,000 or higher or with one of the two following labels in the battery compartment provide optimum performance with the Conversion Circuitry.

FFoorr SSuubbssttrroobbee UUpp--DDaattee:: Contact Ikelite for information.

OOppttiioonnaall AAcccceessssoorriiees

SSuubbssttrroobbee DDSS5511 PPaacckkaaggeess

PPaacckkaaggee ##33994444..4455 Includes: DS51 Digital Substrobe Ikelite TTL Sync Cord Strobe Arm Is #4075.1

PPaacckkaaggee ##33994444..5511 Includes: DS51 Digital Substrobe

kelite TTL Sync Cord

I Strobe Arm #4086.61 (ball socket arm)

The DS51 Digital Substrobe is equally

uited for general and wide-angle

s photography, covering up to 80° with the diffuser. Powered by four AA-size batteries, the compact size of the DS51 makes it ideal for macro photography.

Substrobe DS51

Sync Cord

Strobe Arm

IIkkeelliittee PPhhoottooccaassee

Waterproof equipment carrying case featuring die-cut foam openings to accommodate the camera housing, strobes, mounting arms, etc. PPhhoottooccaassee ##33994400..44

with die-cut foam.

serial number

OOppttiioonnaall AAcccceessssoorriieess,, ccoonntt..

SSuubbssttrroobbee DDSS112255 PPaacckkaaggeess

PPaacckkaaggee ##33994444..7755 Includes: DS125 Digital Substrobe

1.5-hour Smart Charger 110/240V Ikelite TTL Sync Cord Strobe Arm #4086.61 (ball socket arm)

The Ikelite DS125 digital Substrobe combines high intensity output and wide 100° angle of coverage with the diffuser, in a compact, versatile design. The easily interchangeable and rechargeable NiMH battery pack recycles in 1.0 second. Built-in modeling light / night diving light.

serial number

Strobe Arm

Substrobe DS125

Sync Cord

OOppttiioonnaall AAcccceessssoorriieess

BBaacckk OO’’rriinngg

O’rings last for several years if properly maintained. (See maintenance) Always carry a spare.

UURR//PPrroo FFiilltteerr ((BBlluuee WWaatteerr))

The UR/Pro underwater color correcting filter is designed to restore some of the warm colors filtered out by the water. For available light use only, not recommended for use with flash.

GGrreeeenn WWaatteerr FFiilltteerr

Enhances contrast and alters the color of green water to give our subject a rich, natural tone. For available light only, not recommended for use with flash.

UUssee tthhee EEVV CCoonnttrroolllleerr wwiitthh aa DDSS SSuubbssttrroobbe

The EV Controller provides 10 manual power settings in 1/2 stop increments for the DS51 or DS125 Substrobes. The EV Controller has a built-in slave which can be triggered by the camera’s built-in flash.

IIkkeelliittee WW--2200 WWiiddee--AAnnggllee LLeennss

Wide-Angle lenses allow you to capture more of the scene and get closer to your subject which results in clearer images and more vivid color. Can be installed or removed underwater for maximum versatility. (Note: some housings may require an adapter, see instructions.)

##00113322..5599

##66444411..4411

##66444411..8811

##66442200

SSuubbssttrroobbee PPaacckkaaggeess aavvaaiillaabbllee

Ikelite Ball Arm Systems are provided with these packages

#3944.45 SubStrobe DS51 with Sync Cord & Strobe Arm #3944.51 SubStrobe DS51 with Sync Cord & Ball Socket Arm #3944.75 SubStrobe DS125 with Sync Cord & Ball Socket Arm

MMaaiinntteennaanncce

The Ikelite Digital Housing should be given the same care and attention as your other photographic equipment. In addition to

ormal maintenance we recommend that the housing be returned

n to Ikelite periodically to be checked and pressure tested.

leave the camera and housing in direct sunlight for

DDoo NNoot prolonged periods. Heat may damage the camera. DDoo NNoott

ship the camera in the housing.

3. Before using the housing, always check the tightness of the sseett ssccrreeww Check each

in each control knob.

ccoonnttrrooll ggllaanndd

to make sure they are tight. There

is a slight chance that either could vibrate loose during travel.

. Keep the back o’ring clean and lightly lubricated. To lubricate

remove the o’ring from the back. Put a small amount of lkelite lubricant on your fingers. Draw the o’ring through your fingers to apply a light coating of lubricant. Only apply enough lubricant to make the o’ring feel slick.

DDoo NNoott ssttrreettcchh tthhee oo’’rriinngg This light coating of lubricant will help to keep the o’ring from drying out and will help to show a dark sealing line when the housing back is properly sealed.

5. Keep the area where the o’ring fits and the sealing surface of the housing clean.

6. Rinse the housing exterior in fresh water after each salt water use. Dry with a soft cloth. Dry lens port to eliminate spotting. After several uses in salt water soak the housing in a mild soap solution, rinse and dry before storage. When storing the housing, remove the back o’ring, lightly lubricate and place in a plastic bag. Place the plastic bag with o’ring inside the housing for safe keeping.

CCAAUUTTIIOONN

NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaan ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk.

CCoonnttrrooll MMaaiinntteennaanncce

Ikelite controls are designed to provide years of reliable service with minimal maintenance.

1. Push button controls require no maintenance other than rinsing in fresh water after saltwater use. If a push button control becomes difficult to push or if it sticks when depressed, soak the housing in luke warm fresh water. After a few minutes operate the push button. If this does not correct the problem, return the housing to Ikelite for maintenance.

2. Some of the controls have long shafts. These controls can be

lubricate shaft

housing

pull out to expose shaft

pulled out, exposing the shaft (see drawing). To lubricate the control, gently pull on the knob until the stainless steel shaft is exposed. Lightly lubricate the shaft, then move the shaft in and out several times. This will lubricate the x’ring in the Ikelite control gland. This should be done before using the housing after a prolonged storage period, or once a week when the housing is in use.

3. Some of the controls have a short shaft and cannot be pulled out exposing the shaft for lubrication. In the unlikely event one of these controls sticks or becomes difficult to operate you can remove the control from the housing and lubricate it, or return the housing to Ikelite for maintenance. To remove the control, loosen the set screw in the knob (allen wrench required); remove the knob. If there is salt or dirt build-up on the exposed control shaft, clean the shaft. Open the housing and gently slide the control shaft out of the control gland. Clean and lightly lubricate the shaft, including the end of the shaft. Slide the shaft back into the control gland and gently slide it back and forth a few times without fully removing the shaft from the gland. Replace the knob, NOTE the flat area on the shaft, the set screw in the knob should tighten down against the flat area on the control so the knob does not turn on the shaft.

control shaft

Flat

Tighten set screw down

against this area when

replacing the knob.

housing

Lubricate end of shaft before reinserting into gland

gland

Loosen set screw (allen wrench required)

GGeenneerraall TTiippss

1. Due to the power required to operate the camera, flash, and LCD screen it is a good idea to start each dive with a fresh set of batteries.

2. Some cameras reset their flash to AUTO when the camera is turned on. If you prefer another setting be sure to select it.

3. As soon as you enter the water, take a moment and check the housing to see that it is properly sealed.

4. Next, check to see if there are any bubbles on the face of the lens port. If there are, take your finger and remove them. If there are bubbles on the lens port they can produce soft focus spots in your photographs.

5. If you use the housing Zoom control, make sure to move it back to the center position. If the housing Zoom control is pushing the camera zoom lever to either side the camera will not function.

PPhhoottoo TTiippss

1. The number one rule in underwater photography is eliminate as much water between camera and subject as possible. Get as close as you can to the subject, then use the zoom. If you are using flash, subjects beyond 6 feet (1.8m)will not have much color.

2. Digital cameras have a slight lag time between when you press the shutter release button and the camera actually takes the picture. Hold the camera steady a second or two after pressing the shutter release button.

3. Do not shoot down on subjects as they will quite often blend into the background and be difficult to see in the photograph. Shoot subjects straight on or shoot up at a slight angle using the blue water as a contrasting background.

PPhhoottoo TTiippss CCoonntt.

4. Underwater flash is used to restore the warmer colors filtered out by the water as well as to illuminate the subject. When photographing underwater, set the camera to use flash on every shot. If the camera’s flash is set to AUTO and the sun is behind your subject, the camera may see enough light that it does not fire the flash. With the sun behind the subject the subject is shaded (dark) and needs flash for a good exposure.

5. Since opinions vary on what is the correct exposure you may want to adjust your camera for what you like exposure wise. Many cameras allow you to adjust both available light and flash exposure with an EV control.

6. Many photographers transfer their images to the computer where they can fine tune the appearance of the image. Many of the image manipulation programs make you think you can magically correct any image taken and make a good picture. One thing to remember when using image manipulation programs, if the image is overexposed much of the color is missing. If the color is missing you cannot adjust it. If images are underexposed some color and detail may be there, it is just dark and you can adjust it to some degree. So if you error in exposure it is better to have the image slightly underexposed than over exposed.

NNootteess::

____________________________________________________________________

NNootteess::

____________________________________________________________________

_________________________________________________________________ .

IIkkeelliittee LLiimmiitteedd WWaarrrraannttyy

All Ikelite products are warranted against any manufacturing defects for a period of one year from the date of purchase. Defective products should be returned prepaid to Ikelite. Ikelite will, at its discretion, repair or replace such products, and will return to customer prepaid. All other claims, of any nature, including but not limited to bulb failure are not covered. Except as mentioned above, no other warranty expressed or implied, applies to this Ikelite product.

RReettuurrnniinngg PPrroodduuccttss ffoorr SSeerrvviiccee

Ikelite is most interested in preforming any service to assure that all products perform as intended. For repair or service, return the product to the address below with your name, address, phone number and a brief description of the problem. Evidence of purchase date must be provided to obtain warranty service.

____________________________________________________________________

_________________________________________________________________ .

IIkkeelliittee UUnnddeerrwwaatteerr SSyysstteemmss

5500 WW 3333rrdd SSttrreeeett

IInnddiiaannaappoolliiss,, IINN 4466220088 UUSSAA

331177--992233--44552233

eemmaaiill:: iikkeelliittee@@iikkeelliittee..ccoomm

wwwwww..iikkeelliittee..ccoomm

DDiiggiittaall 66114400..0055--0011--00880077

Ikelite S5 IS User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual