– Intense 7.5w medium spot beam powered by 4 D-cell alkaline batteries.
RRCCDDHHRR
RRCCDDSSuuppeerr--88
and lantern grip handles provided.
RRCCDDSSuuppeerr--88RR
Interchangeable pistol and lantern grip handles provided.
Comfortable hand grip for exploration night or day. Quartz halogen lamp and UV-coated
patterned reflector create a magnificient beam with good peripheral coverage. Virtually
indestructible casing.
switch and sliding lock afford easy operation even when wearing a bulky glove. Nickel
plated brass contacts boost the electrical efficiency and corrosion resistance. Waterproof
to 90m (300 feet).
LLeeggeennddaarryyFFlliipp--LLoocckkDDeessiiggnn
makes opening and closing incredibly easy and dependable. Simply flip the locking lever up,
rotate, and the internal spring automatically pushes open the light for easy bulb or battery
–Ultra-intense rechargeable. Penetrating 19w wide beam with blinding center spot.
– Super intense 15w light powered by 8 alkaline D-cells. Interchangeable pistol
Rubber shroud protects the front lens while blocking side reflections. Large rotating
– Blinding 25W intensity powered by industrial grade ni-cad module.
–You will never find the RCD stuck shut. Unique flip-lock lever
replacement. Flip the locking lever down and the RCD seals with ease and confidence.
NNOOTTEE::
Ikelite's black vinyl lanyard is NOT recommended for use with RCD Super-8/8R. The
vinyl lanyard is designed to be broken in an emergency and the weight of the Super-8/8R
may cause the lanyard to break during normal use.
NNoottee::
Please read all instructions before using this product.
• Slide the locking lever out and flip the lever up.
• Rotate the lever counter-clockwise 90° and the internal spring automatically pushes open
the light.
• Lift the body off of the front. The batteries remain housed in the front.
There are two ways to slide the locking lever out: grasp the sides of the lever and pull out
OR use your thumb to apply slight pressure to the top of the lever and slide it out.
• Make sure the on/off switch has been rotated to the off position.
• Place the front assembly face down on a flat surface. Check that the o-ring and sealing surfaces
are clean; make sure the o-ring is positioned properly.
• Place the locking lever in the open position (slide the lever out, flip the lever up, and rotate the
lever counterclockwise).
• Align the handle on the body with the front assembly as referenced. Lower the body on the
front. Proper alignment of the body with the front is extremely important to avoid possible
damage to the internal components.
• To seal the light, simply reverse the opening sequence. Press down slightly on the body and
rotate the lever clockwise. Flip the lever down and slide the lever in to the locked position.
The large rotating switch with sliding lock is easily operated with one hand. We recommend
locking the switch when the light is not in use. Never look into the face of the lite because of its
blinding intensity.
RRCCDDHHaannddHHRR::
Grasp the light in your right hand. To unlock the switch, squeeze your index finger to slide the
switch lock towards the back of the light. Rotate the switch to the right to turn on the light. Use
your thumb to slide the switch lock forward to lock the switch in the off position.
RRCCDDSSuuppeerr--88aannddSSuuppeerr--88RR::
Slide the center switch lock forward to unlock the switch. Rotate the switch 90° to turn on
The RCD H features the high intensity 5.0V lamp producing an incredibly bright penetrating
medium spot beam intended primarily for underwater use. Alkaline batteries provide 7.5-watt
initial intensity and 5-6 hours of high intensity light. Consumer ni-cads reduce the intensity and
burn time.
Make sure the bulb is cool. Remove the batteries to access the bulb holder. Squeeze the ends of
bulb holder and remove. Tip the front up and drop the bulb into your hand. Place the new bulb in
the front and replace the bulb holder (orient it either way).
Ikelite offers two bulbs compatible with the RCD H. The standard bulb provided is the 5.0V
higher intensity halogen bulb IKE4 #0042.55 offering a 5-6 hour burn time and 10-hour life.
It is intended primarily for undewater use.
The optional 5.2V halogen bulb #0042.52 provides a 10-hour burn time and 20-hour life.
It is offered for extended use above water or to almost double the burn time and lamp life.
In an emergency, use a common PR-size 4.8–5.2V bulb.
The RCD Super-8 features the super intense 10V halogen
lamp producing an incredibly bright penetrating medium
spot beam intended primarily for underwater use. Alkaline
batteries provide 15W initial intensity and 6 hours of high
intensity light. Consumer ni-cads reduce the intensity and
burn time.
• Note the polarity markings on the front head assembly.
• The four batteries closest to the handle must be inserted
positive end DOWN; the back four
batteries must be inserted positive end UP.
• For best performance, we recommend Energizer®
alkaline batteries.
Ultra-intense rechargeables. The RCD HR features a penetrating 19W beam while the
Super-8R provides 25W intensity. Both run for 1.25 hours per charge. Industrial grade 5Ah ni-cad
module produces considerably more power than consumer ni-cads. Not intended for extended
use above water.
RCD HRSuper8R
#0083.9Charger 110/220V USA plug................ Recharge time: 6 hours14 hours
#0083.91Charger 220V European plug............. Recharge time: 6 hours14 hours
#4063-seriesSmart Charger variable 100-240V, choice of
USA, Euro, Australian plug................. Recharge time: 4 hours5 hours
When using charger #0083.9, place 110/220V selector in appropriate position.
Make sure the bulb is cool. Remove the batteries to access the bulb holder. Squeeze the ends
of bulb holder and remove. Tip the front up and drop the bulb into your hand. Place the new bulb
IKE8 #0042.58 in the front and replace the bulb holder (orient it either way).
In an emergency, use a common PR-size bulb approximating 10V.
Use 4.7V bulb #0040.18 for the RCD HR and 6V bulb #0040.20 for the Super-8R. Make sure the
old bulb is cool. Remove ni-cad module to access the bulb holder. Squeeze the ends of bulb holder
and remove. Insert new bulb in the holder. DO NOT touch the bulb because of the oils on your
fingers; use a soft cloth or tissue when replacing. Light intended primarily for undewater use.
6
IINNTTEERRCCHHAANNGGEEAABBLLEE HHAANNDDLLEES
S
IINNTTEERRCCHHAANNGGIINNGG MMOODDEELLS
S
Only the Super-8 and 8R feature interchangeable handles and both the lantern grip and pistol
grip handles are supplied. To change the handle, access the screw underneath the locking lever by
first sliding the locking lever out and then flip the lever up.
Remove the screw and washer and then slide the handle out of the body. Slide the other handle
into the groove and secure with the screw and washer.
NNOOTTEE::
Ikelite's black vinyl lanyard is NOT recommended for use with RCD Super-8/8R. The vinyl
lanyard is designed to be broken in an emergency and the weight of the Super-8/8R may cause the
lanyard to break during normal use.
RREEPPLLAACCEEMMEENNTT PPAARRTTS
AA--EE99001122..22
AA--EE99001122..1188
AA--EE99001122..8888
AA--EE99001122..9966
AA00550011
BB9900 1122
BB9900 1122..1177
BB9900 1122..8800
BB9900 1122..9955
CC00004422..5555
C0040.18 HR BULB, 4.7V halogen
CC00004422..5588
CC00004422..2200
DD99001122..33
DD99001122..3388
EE00112233
FF99001133
FF99001133..88
00008833..99
00008833..9911
GG99001122..55xx
GG99001122..88xx
00991100
Head assembly complete with bulb: H
Head assembly complete with bulb: HR
Head assembly complete with bulb: Super-8
Head assembly complete with bulb: Super-8R
Rubber shroud: all models
Head with hydrogen absorber: H
Head with hydrogen absorber: HR
Head with hydrogen absorber: Super-8
Head with hydrogen absorber: Super-8R
H BULB, IKE4 5.0V halogen, standard higher intensity
Super-8 BULB, IKE8 10.4V halogen
Super-8R BULB, 6V halogen
Bulb holder/contact bar: H and Super-8
Bulb holder/contact bar: HR and Super-8R
O-ring: all models
Ni-cad battery module: HR
Ni-cad battery module: Super-8R
Charger, USA 110/220V 6-hour
Charger, Euro 220V 6-hour
Body assembly with toggle: note color H and HR
Body assembly with toggle: note color Super-8 and 8R
Hydrogen absorber
S
RRCCDDHHaannddHHRR
The HR front head assembly is modified for the rechargeable light which means it is NOT
interchangeable with the 4-cell alkaline version RCD. Only the body assembly is interchangeable
between the H and HR models.
SSUUPPEERR--88aanndd88RR
The Super-8R front head assembly is modified for the rechargeable light which means it is NOT
interchangeable with the 8-cell alkaline version Super-8. Only the body assembly is interchangeable
between the Super-8 and 8R models.
DO NOT use batteries that have been wet; batteries from a flooded lite should be discarded.
Water could create an internal short circuit at some later date causing a potential explosion. The
normal evolution of all batteries is emitting hydrogen gas. This gas must be absorbed or allowed to
escape to prevent ignition of the entrapped hydrogen/air mixture. We suggest storage of your lite
open to allow any hydrogen/air mixture to escape. A hydrogen absorber has been concealed inside
this lite and should NOT be removed. In case the lite floods, install a new hydrogen absorber in the
spare bulb holder and replace the batteries.
All Ikelite products are warranted against any manufacturing defects for a period of one year
from the date of purchase. Defective products should be returned prepaid to Ikelite. Ikelite will,
at its discretion, repair or replace such products, and will return to customer prepaid. All other
claims, of any nature, including but not limited to bulb failure are not covered. Except as mentioned above, no other warranty expressed or implied, applies to this Ikelite product.
IIKKEELLIITTEEUUNNDDEERRWWAATTEERRSSYYSSTTEEMMSS
50 West 33rd Street
PO Box 88100
Indianapolis, IN 46208 USA
317-923-4523
wwwwww..iikkeelliittee..ccoomm
Email ikelite@ikelite.com
77
1200-06-0707
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.