Ikelite Olympus D-230, 6138 Instructional Manual
Ikelite Digital Housing
Shutter Release
S
hutter Lock
Lens Port
Housing
Latch
Lock
Accessory
Shoe
Locking Latch
A
ccessory Shoe
S
hutter Button
T
humb Rest
Tray Mounting Shoes
L
atch
M
onitor
OK
Arrow Pad
Lock
Push back on
Lock and Rotate
the Latch open
Hinge
Hook
Latch
Hinge
Shutter
Release Arm
Foam Spacer
Foam Spacer
Camera
instruction manual
#6138 for Olympus D-230
Congratulations on your purchase of an Ikelite Digital Camera
Housing. Ikelite has over 30 years of experience in the underwater
photographic and lighting market. Our products are designed and
built in the USA by Ikelite for both the professional and amateur
photographer.
The clear housing permits instant visual inspection of the camera
and all sealing surfaces as well as complete monitoring of controls
and camera LCD screens.
This housing has been water pressure tested at the factory.
Housing is pressure tested to 125’ (38m).
OOppeenniinngg tthhee HHoouussiinng
g
Push back on the lock and lift the latch. Unhook the latch from the
front of the housing. The two halves of the housing will now swing
open.
HHoouussiinngg FFrroonnt
HHoouussiinngg BBaacck
2
IInnssttaalllliinngg tthhee CCaammeerra
Slide the camera’s Lens Barrier OPEN, this turns the camera ON.
NNOOTTEE:
:
There is no provision in the housing for sliding the Lens
Barrier once the camera is in the housing.
a
t
k
g
OOppeenniinngg tthhee HHoouussiinng
3
With the housing face down place the right edge of the camera
into the housing as far forward as possible and against the foam
spacer on the right. Gently push the left edge of the camera into
the housing with the base of the camera against the bottom of the
housing. The top foam spacer and the front rubber spacers hold the
camera in position.
IInnssttaalllliinngg tthhee CCaammeerra
a
4
Hook latch
over front
Push latch to
closed/locked position
Hinge
CClloossiinngg tthhee HHoouussiinng
Once the camera is firmly installed in the front half of the housing,
the housing can be closed. Check that the o’ring is properly located
when closing the housing. Place the Latch over the Hook on the
ront of the camera and push the Latch closed as shown below. The
f
red lock should protrude through the opening in the Latch and
nap into place locking the Latch.
s
g
CClloossiinngg tthhee HHoouussiinng
g
CChheecckkiinngg tthhee IInnssttaallllaattiioon
The nice thing about digital cameras is that you can practice
taking pictures and it does not cost anything. You can just
review your pictures to see that everything is working and then
delete them. If the housing is new it is a good idea to take a few
ictures above water to get familiar with the housing and the
p
controls.
BBeeffoorree eenntteerriinngg tthhee wwaatteerr cchheecckk :
1. The camera’s Lens Barrier is fully open and the camera is ON
2. The o’ring is sealed properly
3. The housing controls are aligned properly
CCAAUUTTIIOONN:
SShhuutttteerr RReelleeaasse
The camera's shutter release button operates in two stages.
When depressed halfway it activates the camera's exposure
eter and focus. When depressed fully it takes the picture. This
m
half stop of the shutter release is more easily felt when using
he camera out of the housing. But with some practice you can
t
feel the half stop when the camera is in the housing. The
camera's shutter release requires only minimal pressure to
activate. With the additional leverage of the housing’s shutter
release control you can put undue force on the camera's shutter
release button. This can result in damage to the camera.
Some digital cameras have a noticeable lag time between when
you push the shutter release button and when the camera starts
to do something. It is human nature to push harder when the
camera
the camera
of the shutter release. It only requires a very light touch.
e
does not instantly respond. Take several pictures with
in the housing, paying special attention to the feel
n
:
:
5
LLuubbrriiccaanntts
1. Ikelite provides silicone lubricant with the housing.
We recommend that you use only Ikelite lubricant on Ikelite
products as some other brands may cause the o’ring to swell
and not seal properly.
2. Use only enough lubricant to lightly coat the o’ring. Wipe off
any excess lubricant with a clean cloth. Lubricant is not a
sealant, it is used to reduce friction.
Excessive lubricant can collect sand and dirt which may
interfere with proper sealing.
CCAAUUTTIIOON
s
N
NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaan
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk.
.
6
MMaaiinntteennaanncce
The Ikelite Digital Housing should be given the same care and
attention as your other photographic equipment. In addition to
normal maintenance we recommend that the housing be returned
to Ikelite periodically to be checked and pressure tested.
DDoo NNoot
1.
for prolonged periods. Heat may damage the camera.
DDoo NNoot
2.
Keep the back o’ring clean and lightly lubricated. To lubricate remove
3.
the o’ring from the back. Put a small amount of lkelite lubricant on
your fingers. Draw the o’ring through your fingers to apply a light
n
coating of lubricant. Only apply enough lubricant to make the o’ring
feel slick.
will help to keep the o’ring from drying out and will help to show
a dark sealing line when the housing back is properly sealed.
4. Keep the area where the o’ring fits and the sealing surface
of the housing clean.
5. Rinse the housing exterior thoroughly in fresh water after each
salt water use. Dry with a soft cloth. Dry lens port to eliminate
water spotting.
After several uses in salt water soak the housing in a mild soap
solution, rinse and dry before storage. When storing the housing,
remove the back o’ring, lightly lubricate and place in a plastic bag.
Place the plastic bag with o’ring inside the housing for safe keeping.
CCAAUUTTIIOON
NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann ccaauussee tthhe
ppllaassttiicc hhoouussiinngg ttoo ccrraacckk.
e
t
leave the camera and housing in direct sunlight
t
ship the camera in the housing.
DDoo NNoott ssttrreettcchh tthhee oo’’rriinng
g
. This light coating of lubricant
N
.
e
7
8
Loading...