Ikelite Nikon Coolpix P2, Nikon Coolpix P1, 6182.11 Instruction Manual
Digital Housing
instruction manual
for
Nikon
Coolpix
Housing
#6182.11
P1 & P2
Ikelite Digital Housing
Front View
Shutter
Release
Lid
Snap
Zoom
Menu
Play
Delete
Multi
Selector/OK
Lid
Snap
Lens
Port
Back View
Lanyard
Thumb
Rest
On/Off
Mode
instruction manual
#6182.11 for Nikon CoolPix P1 & P2
PPlleeaassee RReeaad
We suggest that you read this instruction booklet throughly
before use. If you are new to underwater photography be sure
to read the General and Photo Tips.
W
have a full understanding of where each camera control is
ocated and what function each control provides.
l
d
e also suggest that you read the camera manual throughly to
Congratulations on your purchase of an Ikelite Digital Camera
Housing. Ikelite has over 40 years of experience in the underwater
photographic and lighting market. Our products are designed and
built in the USA by Ikelite for both the professional and amateur
photographer.
The clear housing permits instant visual inspection of the camera
and all sealing surfaces as well as complete monitoring of controls
and camera LCD screens.
Ikelite Digital Housings are slightly negative in salt water for
stability. This housing has been water pressure tested at the
factory. Housing is pressure tested to 200’ (60m).
PPlleeaassee RReeaadd IIff UUssiinngg aann EEVV--CCoonnttrroolllleer
The EV-Controller used with Ikelite DS Substrobes have two
ser settings. One setting is for strobe selection, the other is for
u
pre-flash or non pre-flash.
EV-Controller should be set to the pre-flash position when used
with this camera.
TThhiiss ccaammeerraa uusseess pprree--ffllaassh
2
r
h
, thus the
3
OOppeenniinngg tthhee HHoouussiinng
Lift
P
ush For ward
Lid Snap Lock
CAMERA / MOUNT
L
id
H
ook
O
' Ring
Mounting Bolt
Mounting
Tray
1. Lid Snaps have a
LLoocck
g
k
.
To open, push Lid Snap Lock
forward and lift as shown.
Keep pressure on the Lid
nap so it does not fly open
S
quickly.
ome lid snaps have a lot of
S
spring tension once they go over center, have a firm grip on the
lid snap. Lid Snaps may be opened one at a time.
IInnssttaalllliinngg tthhee CCaammeerra
a
Remove the back from the housing. The mounting tray for the
amera is secured
c
to the housing
back. Position the
camera on the tray
nd secure it with
a
the mounting bolt
which threads into
the camera’s tripod
socket.
UUssee aa ccooiin
oorr ffllaatt bbllaaddddeed
ssccrreewwddrriivveerr tto
ttiigghhtteenn tthhe
mmoouunnttiinngg bboolltt sso
tthhee ccaammeerraa iiss ffllaat
aaggaaiinnsstt tthhee ttrraayy.
CCAAUUTTIIOONN:
:
n
d
o
e
o
t
.
Some camera tripod socket threads are plastic. The mounting
tray bolt is metal. Do not cross thread or over tighten as you
may damage the camera tripod socket threads.
4
CClloossiinngg tthhee HHoouussiinng
1. Place housing face down in your
g
housing back
lap or on flat surface.
2. Check to see that there is an
o’ring on the housing back and
hat it is clean and in its proper
t
location.
. Guide the back onto the housing.
3
The o’ring should touch the
o’ring
housing all the way around. There
should be an even gap all the way
round between the housing and
a
housing
the housing back.
4. Lift the lid snaps so they are
extended and place the lid snap
housing back
into the hook on the housing
back.
. To close the housing push
5
down on the lid snaps until
even gap
all 4 sides
they snap into place . Lid
snaps on opposite sides of the
housing should be closed at the
same time. Be sure they are down
housing
o’ring
far enough to engage the lock.
DDoouubbllee cchheecck
k
- Once the housing is closed, check the o’ring seal.
Check the gap between the housing back and the housing, it
should be even all the way around.
Look through the clear plastic back at the o’ring. You should see a
darkened area where the o’ring is compressed against the
housing back. If you do not see an even black compression seal
all the way around the back, open the lid snaps, reseat the
housing back and close the lid snaps. Visually check the seal again.
5
CChheecckkiinngg CCoonnttrroolls
s
Once the housing has been closed, push the controls back into
place. Make sure they line up with the camera’s controls.
TTuurrnn CCaammeerraa OOn
n
Turn the camera on and operate each of the housing controls to
get a feel for using the camera in the housing. Take a few
pictures above water with the camera in the housing.
LLuubbrriiccaanntts
s
1. Ikelite provides silicone lubricant with the housing. We recommend
you use only Ikelite lubricant on Ikelite products as some other
brands may cause the o’ring to swell and not seal properly.
2. Use only enough lubricant to lightly cover control shafts and
o’rings. Wipe off any excess lubricant with a clean cloth.
Lubricant is not a sealant, it is used to reduce friction. Excessive
lubricant can collect sand and dirt which may interfere with
proper sealing.
CCAAUUTTIIOON
N
NNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaan
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk.
.
n
6
7
Loading...