Page 1
Tray with Handle(s)
Instruction Manual
9523.61 Tray with Single Handle
9523.62 Tray with Dual Handles
Package Contents
1/4-20 Shoulder Washer (Qty. 2)
12-24 Shoulder Washer (Qty. 2)
12-24 x 1/2”Screw (Qty. 2)
Quick Release Handle
(Qty. 2 with Dual Tray)
CANON A
OLYMPUS
Split Lock Washer
1/4-20 x 1/2”Screw
(Qty. 2)
Tray Inserts
CANON B
3/8-16 Nut
(Qty. 2)
CANON C
SONY A
Panasonic
SONY B
Small Flat Washer
(Qty. 2 with Dual Tray)
Flat Washer (Qty. 2 with Dual Tray)
1/4” Nut (Qty. 2 with Dual Tray)
Front of Tray
Thank you for choosing Ikelite equipment. Please read this instruction
manual completely before attempting to operate or dive with this product.
Page 2
Attaching Handle to the Tray
Insert handle into the tray as shown below. Attach and tighten to tray
using flat washer and 1/4” nut. The handle is removable in the event that
replacement is necessary. The handle is not intended to be removed for
travel. The completed assembly may be removed and replaced easily for
travel.
Quick
Release
Handle
Handle
Guide
Pin
Small Hole
2
Small Flat Washer
Threaded Handle Stem
Flat Washer
Stem Hole
1/4” Nut
Page 3
Canon, Olympus, Panasonic, and Sony Housings
SONY B
SONY A
Panasonic
Match your housing
to the correct tray
CANON A
CANON B
CANON C
insert as shown.
The insert cut-out
should match the
OLYMPUS
SONY A
Panasonic
bottom of the
housing tripod mount base plate,
Tray Inserts
diagram A. Remove protective backing to expose adhesive and attach
insert to recess in the center of the tray, diagram B. Attach tray to
housing through Center Hole using 1/4-20 x 1/2” Screw and Split Lock
Washer, diagram C.
Diagram A
Diagram B
SONY B
SONY A
Panasonic
SONY B
Diagram C
1/4-20 x 1/2”Screw
Split Lock Washer
Front of Tray
Center
Hole
Protective
Backing
1/4-20
Threaded
Mounting
Hole
3
Page 4
Ikelite Housings
Attach tray to Ikelite housing using two 12-24 x 1/2” Screws and
Shoulder Washers for housings with female-threaded mounting systems.
For male-threaded mounting systems with a housing serial number
less than 37,101, order spacer 9523.09. Tighten tray with spacer using
the two 3/8-16 nuts.
12-24 x 1/2”Screw
Shoulder Washer
Housing Mount
Accessory Mounting Points
The bottom of the tray features two 1/4-20 threaded mounting holes for
attachment of a Pro-Video battery pack, diagram B, page 3.
Limited Warranty
This product is warranted against any manufacturing defects for a period
of one (1) year from the original date of purchase. Defective products
should be returned to Ikelite postage paid. Ikelite will, at its sole
discretion, repair or replace such products, and will return to customer
postage paid. All other claims of any nature are not covered. Except as
mentioned above, no other warranty expressed or implied applies to this
Ikelite product.
Ikelite Underwater Systems
Indianapolis, IN 46208 USA
50 West 33rd Street
9523.61.62_Tray_Handle(s)_4-0113
Loading...