Ikegami LCM-971 User Manual

Installation and User’s Gui

de

Please read this manual thoroughly before use and keep for future reference.

INSTRUCTION MANUAL

9.7” LCD VIDEO MONITOR

Model :

LCM-971

- 1 -

Installation and User’s Gui

de

please do not use them.

Warning Statements

* Follow this safety instruction to use the monitor properly and prevent the damages.

* This safety instruction has “ Warning” and “ Caution” as below.

WARNING:

CAUTION:

If the user does not follow this instruction,
it may cause the serious damage to the user.

If the user does not follow this instruction, it may cause the slight
damage to the user or cause some damages to the monitor.

* Keep this user’s guide book for later use.

Never remove the back over and touch
the inside of the monitor. If you need a
service, please contact the service center.

Keep away the monitor from the
direct sunlight and a heating appliance.

Never push objects of any kind into this
product as they may result in a risk of fire
or electric shock.

Connect the power code to the wall
outlet tightly. If the power code or plug are
defective and the wall outlet is not tight,

- 2 -

Installation and User’s Gui

de

How to fix

Warning Statements

Do not install this monitor on the outside
and near water. If may cause damage to
the product, electric shock and fire.

For cleaning do not use liquid cleaners.
Never touch the power plug with wet­hands.

When lightning and thundering, unplug
the monitor from the wall outlet and never
touch it.

Unplug this product from the wall outlet,
when It does not operate for a long time.

When smoking and noising from the
monitor, unplug the product from the wall
outlet and contact a service center.

1. Do not open this product as it contains high voltage inside.

2. It may create an electric shock.

3. It the user disassembles and remove the back cover, it does not make sure

4. To make up for the damages and do a service and exchange the monitor..

- 3 -

Installation and User’s Gui

de

Cautions

Install this monitor some distance
From the wall and do not install unless
Proper ventilation is provided.

The openings must not be blocked by
curtain, rug or other similar surface.

Before carrying the monitor, tum it off and
Unplug the signal cables and the power code
From the wall outlet.

Install this monitor about 50cm far from
the eyes and an angle of 0~15 degrees
below eyes. Too close installation may
cause having weak sight.

For cleaning, unplug the monitor from the Wall
outlet. Do net use the liquid cloth. Use the soft
cloth.

Place this product on a stable place.
If not, it may fall, causing serious
Damages to the monitor and people.

When carrying this monitor, be careful
not to damage the panel and drop it
It may cause some trouble.

Take the power plug out from the wall
outlet. Do not pull the cable. It may snap the
inner wires and cause overheating and fire.

Do not press the LCD panel with hands or the
sharpened material hardly.

Do not use the chemical liquid for cleaning. It
may cause fading and breakage.

- 4 -

Installation and User’s Gui

de

TABLE OF CONTENTS

1.1

Unpacking

……

.....

............................................................

.................

.................

...........

2. OSD SETTING

…

...

............................................................

.................

....................

....

..

..

............................................................

.................

....................

1.3 Main Functional Button

s

……

.....

.....

.......................................................

.................

........

1.2

Part List

……

.....

............................................................

.................

............................

1.4

Connection

……

.....

............................................................

.................

..

........................

6

8-11

13

13

11

1

2

1. INSTALLATION

3. SPECIFICATION

4. APPENDIX

5. TROUBLESHOOTING

6. LIMITED WARRANTY

.................................................................................................................

.............................................................................................................

- 5 -

Installation and User’s Gui

de

INSTALLATION

POWER ADAPTOR

VGA CABLE

1.1 Unpacking

Remove the package cover and place the product on a flat and secure surface or in the installation
location. This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately. Check whether all the following device and
accessories are included with the main system. If any items are missing, notify your Sales or
Customer Service Representative.

1.2 Part List

The following table lists the parts included:

MONITOR USER’S GUIDE EXTERNAL POWER CABLE

- 6 -

Installation and User’s Gui

de

INSTALLATION

1

2

3

4

5

6

7

8

8 8 1 2 3 4 5 6 7

1.3 Main Functional at Front Panel

MENU / EXIT

Activates and exits the OSD.

SOURCE / ▽▽▽▽

Select input source, and move the OSD menu.

AUTO / △△△△

Move the OSD menu and auto adjustment of RGB source.

◁◁◁◁ / VOL

Decrease the level of volume and move the previous menu.
Enable Key lock On/Off control while it is pushing for 3 second.

▷▷▷▷ / SELECT

Increase the level of volume and select the OSD menu.

/ POWER

Turns the power ON or OFF. There will be a few seconds delay before the display appears.
The power LED(next to the power switch) lights with green when the power is turned ON.
The power is turned off by pressing the power switch again and the power LED goes Red.

LED LAMP
Power ON Indicator

SPEAKERS

- 7 -

Installation and User’s Gui

de

1

2

3

4

5

6

7

8

9

10

11

1.4 Connection at Back Panel

1. HDMI Input

2. AV1 Input

Composite signal input for AV 1.

3. AV1 Output

Video Looping output for AV 1.

4. AV2 Input

Composite signal input for AV2.

5. AV2 Output

Video Looping output for AV 2.

- 8 -

6,7. AUDIO1 IN

Stereo audio signal input.
This input for AV1 and S-VIDEO.

8. S-Video Input

Y/C separated signal input.

9. PC AUDIO Input

10 RGB Input

11. DC 12V Input

Installation and User’s Gui

de

O

SD (On Screen Display) SETTING

AV1, AV2, S

-

VIDEO

■ A. INPUT Select

Inputs can be set to AV1, AV2, S-VIDEO, HDMI and PC mode.

1. Press the SOURCE button and then ▲/▼ Button to move the source

2. Press the ▶ button to select the source.

3. Press the MENU/EXIT Button to exit the INPUT menu.

■ B. MENU SELECTION

1. Press the MENU/EXIT key to access the main menu.

2. Use the  and  arrow key to highlight a selection.

3. Press the ►/SELECT key to select an item.

4. Use the  and  arrow key to highlight a selection.

5. Use the ◀ and  arrow key to adjust the setting on a selected item.

■ C. PICTURE MENU on OSD

C. 1 INPUT SOURCE (AV1, AV2, S-VIDEO, HDMI)

- OSD Menu is working on after it connects the source signal.

HDMI

- 9 -

Installation and User’s Gui

de

1. Press the MENU/EXIT Button and then ◀ / ▶ Button to select the PICTURE menu.

2. Press the ▲ or ▼ Button and then button to select the Button to select the adjustment item you

need.

3. Press the ◀ or ▶ Button to active the item.

Ex) if you select the BRIGHTNESS, then the below picture appears on the bottom screen.

4. Press the MENU/EXIT button to move to the previous menu.

C.2 INPUT SOURCE (PC Mode only)

5. Press the MENU/EXIT Button and then ◀ / ▶ Button to select the PICTURE menu.

6. Press the ▲ or ▼ Button and then button to select the Button to select the adjustment item you

need.

7. Press the ◀ or ▶ Button to activate the function.

Ex) if you select the BRIGHTNESS, then the below picture appears on the bottom screen.

8. ‘Auto’ function is adjusting the location of screen by receiving the sync signal from PC.

Ex) Resolution change.

9. ‘Color Auto’ is adjusting the optimum color coordination automatically.

■ D. VOLUME MENU on OSD (AV1, AV2, S-VIDEO, PC, HDMI)

1. Press the ▶/Enter button for adjusting the volume up and down.

- 10 -

Installation and User’s Gui

de

■ E. SYSTEM MENU on OSD (AV1, AV2, S-VIDEO, HDMI)

AV1, AV2, S-VIDEO, HDMI

PC (VGA)

1. Press the MENU/EXIT Button and then ◀ / ▶ Button to select on the SYSTEM menu.

2. Press the ▲ or ▼ Button and then button to select the Button to select the adjustment item you

need.

3. Press the ◀ or ▶ Button to active the item.

Press the MENU/EXIT button to move to the previous menu

■ F. FUNCTIONS MENU on OSD (PC Mode only)

1. Press the MENU/EXIT Button and then ◀ / ▶ Button to select the FUNCTION menu.

2. Press the ▲ or ▼ Button and then button to select the Button to select the adjustment item you

need.

3. Press the ◀ or ▶ Button to active the item.

4. Press the MENU/EXIT button to move to the previous menu.

- 11 -

Installation and User’s Gui

de

■ G. HOT KEY Function Definition

OSD KEY Function

MENU / EXIT OSD ON/OFF, Exit

MODE/DOWN Source Change, Menu down

VOL+/RIGHT Volume menu On / Volume Up

VOL-/LEFT Volume Down

AUTO/UP Auto Adjust, Menu up

POWER POWER ON / OFF

SPECIFICATION

VIDEO

Screen Size 9.7”

Pixel Type Active Matrix TFT

Panel Resolution

1024 x 768 @60Hz

Pixel Pitch 0.192mm x 0.192mm

Brightness

300 cd/㎡

Contrast Ratio 600 : 1

Aspect Ratio

Viewing Angle (H/V)

Display Color

Response Time

4 : 3

178°/178°

262,244 colors (6 bit)

< 35ms

Video System NTSC / PAL / SECAM

Frequency (H) 30 ~ 61KHz

Frequency (V) 55 ~ 75Hz

Panel Lamp Life 10,000hours

Power Source DC12V adapter (Auto Switching)

- 12 -

Installation and User’s Gui

de

APPENDIX

1. D-SUB Connector PIN Assignment

2. HDMI

Type

A PIN Assignment

PIN NO. PIN Name

1

2

3

4

5

6

7

8

RED VIDEO 9 NC

GREEN VIDEO 10 SIGNAL CABLE DETECT

BLUE VIDEO 11 GROUND

GROUND 12 SDA (for DDC)

GROUND 13 H-SYNC

RED GROUND 14 V-SYNC

GREEN GROUND 15 SCL (for DDC)

BLUE GROUND

PIN NO. PIN Name

1

2

TMDS Data2+ 11 TMDS Clock Shield

TMDS Data2 Shield 12 TMDS Clock-

PIN NO.

PIN NO. PIN Name

PIN Name

3

4

5

6

7

8

9

10 TMDS Clock+

TMDS Data2- 13 CEC

TMDS Data1+ 14 Reserved (HDMI 1.0-1.3c), HEC Data -

TMDS Data1 Shield 15 SCL (PC serial Clock for DDC)

TMDS Data1- 16 SDA (PC serial Clock for DDC)

TMDS Data0+ 17 DDC/CEC/HEC Ground

TMDS Data0 Shield

TMDS Data0-

18

19

+5V Power (max 50 mA)

Hot Plug Detect (All Versions) and HEC Data +

(Optional, HDMI 1.4+ with Ethernet)

- 13 -

Installation and User’s Gui

de

TROUBLESHOOTING

*

When

the

followin

g

troubles

are

occurred,

follow

the

trouble

shooting

b

efore

contacting

Limited Warranty

service center.

Troubleshooting Troubleshooting Tip

The screen doesn’t show up

1. Make sure if the power supply is connected property

2.

Turn on the power.

3. Select the input signal right for the connected port.

a

The screen is too light or to dark

The screen size is not fit for the PC
signal

The screen color shows strange in
the PC signal

Control the BRIGHTNESS

Press the AUTO key among keys in the front.
(It is used only in the PC signal)

In the FUNCTION menu of OSD menu, perform the AUTO­ADJUST.

All products carry a limited warranty from ship date against defects in materials and
workmanship. We are not liable for improper installation that results in damage to mounts,
adapters, display equipment or personal injury.

- 14 -

Installation and User’s Gui

de

Ikegami Electronics (U.S.A.), Inc.

37 Brook Avenue, Maywood , NJ 07607-1195

Phone:[phone] , Fax :[phone]

- 15 -