Ikegami LCM-205N, LCM-205MN User Manual

G

G

G

G

20-INCH

TFT-LCD PUBLIC VIEW MONITOR

Model : LCM-205N

INSTRUCTION MANUAL

Please read this manual thoroughly before use, and keep it handy for future reference.

CONTENTS

SAFETY INSTRUCTION…………………………………………………………………….2 - 3

CAUTIONS ………………………………………..……………………………………………..4

FCC RF INTERFERENCE STATEMENT …………………………………………………….5

CONNECTING WITH EXTERNAL EQUIPMENT…………………………………………… 6

REMOTE FUNCTIONS ……………………………………………………………………….. 7

CONTROLS AND FUNCTIONS…………………………………………………………..8 - 18

D-SUB CONNECTOR PIN ASSIGNMENTS ……………………………………………….19

POWER MANAGEMENT……………………………………………………………………..20

SPECIFICATIONS…………………………………………………………………………21 - 25

VESA MOUNT AND CEILING MOUNT HOLE……………………………………………..26

TROUBLE SHOOTING GUIDE. ……………………………………………………………..27

.

This Monitor was
Manufactured by ISO 9001
Certified Factory

INSTRUCTION MANUAL-------------------------------------------------------------------------------------------1

SAFETY INSTRUCTION

1. Read all of these instructions.

2. Save these instructions for later use.

3. Follow all warnings and instructions marked on the product.

4. Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

5. Do not use this product near water.

6. Do not place this product on an unstable cart, stand or table.

The product may fall, causing serious damage to the product.

7. Slots and openings in the cabinet and the back are provided for ventilation: to ensure reliable

operation of the product, these openings must not be blocked by placing the product on a bed,

sofa, rug or other similar surface.

This product should never be placed near or over a heat register.

This product should not be placed in a built-in installation unless proper ventilation is provided.

8. This product should be operated from the type of power source indicated on the marking

label. If you are not sure of the type of power available, consult your dealer or local power

company.

9. This product is equipped with a 3 wire grounding type plug having a third (grounding) pin.

This is a safety feature. If you are unable to insert the plug into the outlet, contact your

electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type

plug.

10. Do not allow anything to rest on the power cord.

Do not locate this product where persons will walk on the cord.

11. If an extension cord is used with this product, make sure that the total of the ampere ratings

on the products plugged into the extension cord do not exceed the extension cord ampere

rating. Also, make sure that the total of all products plugged into the wall outlet does not

exceed 10 amperes.

12. Never push objects of any kind into this product through cabinet slots as they may touch

dangerous voltage points or short out parts that could result in a risk of fire or electric shock.

Never spill any kind of liquid on the product.

13. Do not attempt to service this product yourself, as opening or removing covers may expose

you to dangerous voltage points or other risks.

2 ------------------------------------------------------------------------------------------- INSTRUCTION MANUAL

SAFETY INSTRUCTION

Refer all servicing to service personnel.

14. Unplug this product from the wall outlet and refer servicing to qualified service personnel

under the following conditions.

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the Product does not operate normally when the operating instructions are followed. Adjust

only those controls that are covered by the operating instructions since improper adjustment

of other controls may result in damage and will often require extensive work by a qualified

technician to restore normal operation.

E. If the product has been dropped or the cabinet has been damaged.

F. If the product exhibits a distinct change in performance, indicating a need for service.

CAUTION

The power supply cord is used as the main disconnect device, ensure that the

Socket-outlet is located / installed near the equipment and is easily accessible.

ATTENTIONN

Le cordon d`alimentation est utillsé comme interrupteur général. La prise de

courant doit être située ou installée à proximité du matériel et être facile

d`accès

CAUTION TO SERVICE PERSONNEL

POWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE IN
THIS PRODUCT UNPLUG THIS PRODUCT FROM THE WALL OUTLET
BEFORE REMOVING THE BACK COVER AND SERVICING

EMISSION CHARACTERISTICS TESTED BY SEMKO

THIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITH
THE NATIONAL SPECIFICATIONS SUCH AS SWEDISH MPR 1990. 10.(MPRII)

INSTRUCTION MANUAL ------------------------------------------------------------------------------------------- 3

ඖG

ඖG

ඖG

ඖG

ඖG

ඖG

CAUTION

NEVER REMOVE THE BACK COVER

Removal of the back cover should be carried out only by qualified personnel.

DO NOT USE IN HOSTILE ENVIRONMENTS

To prevent shock or fire hazard, do not expose the unit to rain or moisture.

This unit is designed to be used in the office or home. Do not subject the unit to vibrations,

dust of corrosive gases.

KEEP IN A WELL VENTILATED PLACE

Ventilation holes are provided on the cabinet to prevent the temperature from rising.

Do not cover the unit or place anything on the top of unit.

AVOID HEAT

Avoid placing the unit in direct sunshine or near a heating appliance.

TO ELIMINATE EYE FATIGUE

Do not use the unit against a bright back ground and where sunlight or other light sources will

shine directly on the monitor.

BE CAREFUL OF HEAVY OBJECT

Neither the monitor itself nor any other heavy object should rest on the power cord.

Damage to a power cord can cause fire or electrical shock.G

4 ------------------------------------------------------------------------------------------- INSTRUCTION MANUAL

FCC RF

FCC RF
INTERFERENCE STATEMENT

INTERFERENCE STATEMENT

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio, TV technician for help.

- Only shielded interface cable should be used.

Finally, any changes or modifications to the equipment by the user not expressly approved by

the grantee or manufacturer could void the user’s authority to operate such equipment.

ሪ DOC COMPLIANCE NOTICE

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital

apparatus set out in the radio interference regulation of Canadian Department of

communications.

.

INSTRUCTION MANUAL------------------------------------------------------------------------------------------- 5

G

- BACK PANEL CONTROL

hG

iG

G j

k

lG

m nG

G oG G pG

CONTROLS AND FUNCTIONS

A. POWER ON/OFF ( )

Turns the power ON or OFF. There will be a few seconds delay before the display appears.

The power LED (next to the power switch) lights with green when the power is turned ON.

The power is turned off by pressing the power switch again and the power LED goes Red.

B. POWER LED

Power ON: GREEN

Stand-by: AMBER

Power OFF: RED

C. IR Sensor

Remote controller sensor.

D. SOURCE

Change input Source one by one

(PC, AV1, AV2, S-VIDEO, C-R)

E. MENU

Activates and exits the On Screen Display.

This button can also be used to move previous menu or status.

OSD MENU (MAIN): Input Source, Screen, Audio, OSD, Color, Utility, Exit.

F. DOWN / UP

This button allows user to enter the sub-menu of the activated function

when down key is pressed on the main menu.

8 ------------------------------------------------------------------------------------------- INSTRUCTION MANUAL