㻌
䢢
䢢
䢢
ġ
㻌
㻌
㻌
Instruction Manual
㻌
㻌
(Introduction Part)
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
Network Camera
IPD-DM300
㻌
OUTDOOR USE WARNING
WARNINGؐTO PREVENT FIRE
OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
Thank you very much for choosing Ikegami network camera.㻌
In order to leverage its capability for the maximum extent, please read the “Instruction Manual”
thoroughly.㻌
Safety Precautions (Be sure to follow all the contents.)
To Use the Product Safely
Before start using the product, thoroughly read this “To Use the Product Safely” and the “Instruction
Manual” and use the product correctly. After reading the manuals, keep them at an easily accessible
place.㻌
㻌
Pictorial Indication
In this manual and on the product, there are many pictorial indications used for achieving safe use of the
product and prevention of damages to you, other people, and your assets.㻌
The indications and meanings are as follows. Please thoroughly understand the contents of the safety
part first, and then start reading the main part.㻌
Please understand that some indications may not match to the actual product that you have purchased.
㻌
It indicates the content with possibilities of death or serious injury due to
Warning
negligence to follow the instruction and mishandling.㻌
㻌
Caution
It indicates the content with possibilities of personal injury or physical
damage due to negligence to follow the instruction and mishandling.㻌
㻌
㻌
Examples of Pictorial Indications
The “ᇞ” symbol indicates the contents that require cautions (including danger and
warning).㻌
㻌
The detailed content of the caution is indicated in the triangle (caution of electric shock
in case of the left drawing).㻌
㻌
The “ż” symbol indicates prohibited actions.㻌
The detailed prohibition content is indicated in or near the circle (prohibition of
㻌
disassembly in case of the left drawing).㻌
㻌
The “Ɣ” symbol indicates the mandatory or instructed actions.㻌
The detailed content of instruction is indicated in the black circle (pulling out the power
㻌
plug from the outlet in case of the left drawing).㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
Usage Note
Warning
Ɣ Do not remove the case and rear panel of the device!
There are sections with high voltage inside, which causes electric shock. Consult
㻌
your dealer or sales person for inspection, servicing, and repair of inside of the
device㻚㻌
㻌
㻌
Ɣ Do not put a container filled with water on the device!
If the water is poured inside of the device, fire or electric shock may be caused.㻌
㻌
㻌
Ɣ Do not place a small metal piece on the device!
If the metal piece drops inside of the device, fire or electric shock may be caused.㻌
㻌
㻌
Ɣ Do not use the power supply voltage that is other than the specified voltage!
Fire or electric shock may be caused.㻌
㻌
㻌
Ɣ Do not pour water on the device or do not wet the device!
Fire or electric shock may be caused.㻌
㻌
In particular, pay close attention when the device is operated in the rain, snow, at the
seaside, and waterfront.㻌
㻌
Ɣ Do not insert a foreign object such as a metal piece or a combustible object
from the aperture of the device! Do not drop such foreign object inside the
㻌
device!
㻌
Ɣ Do not damage the power supply cord! Do not process the cord! Do not forcibly
㻌
㻌
㻌
Fire or electric shock may be caused.
bend the cord! Do not twist the cord!
Do not pull the cord! Do not heat up the cord!
The cord may get damaged, causing fire or electric shock.㻌
Ɣ Do not modify the device!
㻌
Fire or electric shock may be caused.㻌
㻌
Ɣ Do not use the device at a place, where water exists, such as in the bathroom or
the shower room!
㻌
Fire or electric shock may be caused.㻌
㻌
Ɣ When the thunder starts rumbling, do not touch the coaxial connector/cable or
the power supply plug!
㻌
Electric shock may be caused.㻌
㻌
Ɣ Do not connect a device, of which consumption power (W) exceeds the
specified value!
Fire may be caused. The power (W) that the AC outlet of this device can supply is
㻌
indicated near the AC outlet or in the Instruction manual.㻌
Installation
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
Warning
㻌
Ɣ Do not install the device on an unstable location!
The device may be dropped or fallen over, causing injury.㻌
㻌
㻌
Ɣ Do not place a heavy object on the power supply cord! Do not place this device on
the power supply cord!
The cord may get damaged, causing fire or electric shock. If the cord is covered such as
㻌
by a carpet, the cord may be hidden, and a heavy object may be place on the cord.㻌
㻌
Ɣ Do not install the device at where water exists!
Fire or electric shock may be caused.㻌
㻌
㻌
Ɣ Do not connect any device that is other than the specified ones!
Fire or electric shock may be caused.㻌
㻌
㻌
Ɣ When fixing this device, request the work to a specialty constructor!
When fixing this device, it is necessary to take a specified procedure. Otherwise, the
device may be dropped or fallen over, causing fire, electric shock, or injury. In particular , if
㻌
the device is fixed on the wall or to the ceiling, be sure to request the work to a specialty
constructor. In addition, consult your dealer or the sales person for the mounting cost.㻌
㻌
Measures Taken in Abnormal Conditions
Ɣ When there is smoke, strange smell, or unusual sound, turn off the power
immediately and disconnect the power supply plug!
㻌
If the device is continuously used without taking appropriate actions, fire or electric shock
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
may be caused.㻌
Check that the smoke stops and request your dealer or the sales person for the repair.㻌
Never try to repair on your own. It is very dangerous.㻌
Ɣ When water comes inside of the device, turn off the power switch and disconnect
the power supply plug!
If the device is continuously used without taking appropriate actions, fire or electric shock
may be caused.㻌
Contact your dealer or the sales person.㻌
Ɣ When any foreign object comes inside of the device, turn off the power switch and
disconnect the power supply plug!
If the device is continuously used without taking appropriate actions, fire or electric shock
may be caused.㻌
Contact your dealer or the sales person.㻌
Ɣ When the device becomes faulty, turn off the power switch and disconnect the
power supply plug!
If the device is continuously used without taking appropriate actions, fire or electric shock
may be caused.㻌
Request your dealer or the sales person for the repair㻌
Warning
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
Measures Taken in Abnormal Conditions
Ɣ When the device is dropped or when the case is damaged, turn off the power switch and
disconnect the power supply plug!
㻌
If the device is continuously used without taking appropriate actions, fire or electric shock may
be caused.㻌
㻌
Contact your dealer or the sales person.㻌
㻌
Ɣ When the power supply cord is damaged (exposing core wire or broken wire), request
for the replacement!
If the device is continuously used without taking appropriate actions, fire or electric shock may
㻌
be caused.㻌
Request your dealer or the sales person for the replacement.㻌
Warning
Usage Note
Ɣ Do not ride on the device!
㻌
㻌
Ɣ Do not place a heavy object on the device!
㻌
㻌
Ɣ When moving the device, be sure to turn off the power, disconnect the plug, and
remove the connecting cable between equipment!
㻌
㻌
Ɣ If the device is not used for a long time, disconnect the power supply plug from the
outlet for safety purpose!
㻌
Fire may be caused.㻌
㻌
Ɣ Do not look at the sun or the lighting through the lens!
㻌
The device may fall over or get damaged, causing injury.㻌
The device may be unbalanced, and the object on the device may fall, causing injury.㻌
The cord may get damaged, causing fire or electric shock.㻌
The intense light on the eye may cause vision disorder.㻌
Caution
Installation
Ɣ Do not install the device in a location, where is highly humid or much dust exist.
㻌
㻌
Ɣ Do not install the device at a location, where oily smoke or humidity exists, such as on
㻌
㻌
Ɣ Do not block the vent hole of this device!
㻌
Fire or electric shock may be caused.㻌
the kitchen counter or near the humidifier.
Fire or electric shock may be caused.㻌
When the vent hole is blocked, the inside temperature increases, causing fire. Do not use the
device in the following situations.㻌
- Putting the device facing up, horizontally, or upside down. Installing the device to a narrow
place, where is not well ventilated㻌
- Putting the device on the carpet or on the mattress. Covering the device with the tablecloth.
Caution
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
Batteries
㻌
㻌
㻌
㻌
㻌
㻌
㻌
Ɣ Do not locate the power supply cord near the heat generating device!
The cord coating may melt, causing fire or electric shock.㻌
Ɣ When disconnecting the power supply plug, do not pull out by holding the
power supply cord!
The cord may get damaged, causing fire or electric shock.
when disconnecting.
Ɣ Do not plug in or out the power supply cord with a wet hand!
Electric shock may be caused.㻌
Ɣ Do not use a battery other than the specified one!
Due to rapturing or leakage from the battery, fire, injury, or taint of the surrounding
place may be caused.㻌
Ɣ Do not use new batteries and old batteries together!
Due to rapturing or leakage from the battery, fire, injury, or taint of the surrounding
place may be caused.㻌
Ɣ Connect the batteries correctly with the positive and negative polarities in the
correct directions!
When the battery is connected incorrectly, due to rapturing or leakage from the
battery, fire, injury, or taint of the surrounding place may be caused.㻌
Ɣ Do not disassemble or heat up the battery. Do not throw the battery in the fire or
water!
Due to short-circuiting or leakage from the battery, fire, injury, or taint of the
surrounding place may be caused.㻌
Caution
㻌
Be sure to hold the plug
Cleaning
㻌
㻌
㻌
㻌
Ɣ When cleaning the device, turn off the power switch and disconnect the power
supply plug!
Electric shock may be caused.㻌
Ɣ Request the cleaning of inside of the device to your dealer or the sales person
for at least once a year!
If the system is continuously used with the dust being accumulated inside, fire or
breakage may be caused. In particular, it is more effective if the cleaning takes place
before the rainy season with high humidity.㻌
In addition, consult your dealer or the sales person for the cleaning cost.㻌
Caution
㻌
㻌
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance wit h
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
CAUTION;
ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PART
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO
OPERATE THE EQUIPMENT.
㻌
㻌
Instructions for Disposal of Electrical and Electronic Equipment in Private
Households
Disposal of used Electric and Electronic Equipment
(Applicable in the European Union and other European countries with waste recycling,
disposal and collection methods)
This symbol on the product, or in the related documents in the package, indicates
that this product shall not be treated as normal household waste. Instead, it should
be taken to a proper applicable collection point or depot for the recycling of electrical
and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent possible
negative consequences for the environment and human health, which could otherwise caused by
inappropriate handling of this product. The correct recycling of materials will help to conserve
natural resources.
For more detailed information about recycling of this product, please contact your local city authority,
your household waste disposal service or the place where you purchased the product.
The product is intended to be supplied by a Listed Power Unit marked Limited Power Source and
rated output 48Vdc, 0.140A minimum.
The product shall be installed by a qualified service person and the installation shall conform to all
local codes.
The product is to be connected to only PoE networks without routing to the outside plant.
㻌
㻌 㻤
㻌 㻝㻜
㻌 㻝㻣
㻌 㻝㻥㻌
㻌 㻞㻜
Table of Contents
1 Introduction
1.1 Standard Configuration 8
1.2 About the Instruction Manual 8
1.3 Caution on Handling 8
1.4 Disclaimer 9
1.5 Protection of Privacy Information 9
1.6 Cautions of Network Connection 9
1.7 Limiting the Applications of the Device 9
2 Installation
2.1 Names and Functions of Sections 10
3 Connection
3.1 Camera Power Supply 17
3.2 Example of Connection 17
3.3 IP Address 18
3.4 Logging In 18
4 Warranty and After-sales Service
5 Specifications/Exterior
5.1 Specifications 20
5.2 Exterior 21
㻌
1 Introduction
1.1 Standard Configuration
Ɣ Network indoor-type dome camera㻌㻌㻌㻌㻌㻦㻌1 set
Ɣ Instruction Manual – Introduction Part (this manual)㻌 : 1 pc
Ɣ 8-pin terminal block for microphone/alarm㻌㻌 㻌 : 1 pc
Ɣ Monitor output cable㻌㻌㻌㻌㻌㻌㻌㻌: 1 pc
Ɣ Mounting template㻌㻌㻌㻌㻌㻌㻌㻌: 1 set
Ɣ Anchoring screws㻌㻌㻌㻌㻌㻌㻌㻌㻌: 2 pc
Ɣ Screws㻌㻌㻌㻌㻌㻌㻌㻌㻌㻌㻌: 2 pc
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
1.2 About the Instruction Manual
The instruction manual for this device consists of two parts: Introduction Part and Application Part.㻌
This instruction manual explains cautions for handling, installation, and connection.㻌
For the detailed operations and settings of the device, please download the manual from the following
URL.
㻌
http://www.ikegami.co.jp/en/products/download/security.html
㻌
1.3 Caution on Handling
Ɣ Do not use this device at a place, where the device may get poured with water, or a humid place.
Ɣ Do not use the device at a hot or cold place, where the ambient temperature becomes lower than
-10°C or higher than +50°C.㻌
Otherwise, the image quality and parts may get affected adversely or the damage to the device may
be caused.㻌
Ɣ When installing the device in the camera housing, pay close attention to the temperature inside of the
housing. In this situation, the temperature inside of the housing is handled as the ambient
temperature of the camera.㻌
Ɣ Never open the camera case. There are precision components inside; therefore, malfunction or
accident may be caused.㻌
Ɣ When conducting the installation work or connecting, be sure to turn off the power.㻌
Ɣ Do not drop or give a strong shock to the camera while transporting the camera.㻌
Ɣ Do not touch the lens mount inside with a hand or a finger.㻌
Ɣ Do not let the camera face the sun.㻌
Ɣ Due to the characteristics of the imaging element, the screen sometimes becomes rough in high
temperature. However, it is normal and not malfunction.㻌
Ɣ To use the focus function of the lens in the best condition, adjust the flange focus (distance from the
lens mounting surface to the imaging surface).㻌
Ɣ Use a lens that corresponds to 3M pixel in order to leverage the performance of this device.㻌
㻌
㻌
㻌
㻌
1.4 Disclaimer
(1) The purpose of this device is to take the video for monitoring. It is not for crime prevention.㻌
(2) We do not bear any responsibility over the following cases.㻌
a. System failure, accident, and trouble caused by the connection with other maker’s equipment㻌
b. Accident and trouble caused by wrong use or negligence㻌
c. Disassembly and repair that are not authorized by Ikegami㻌
d. Abusive use of the monitored video, which was taken with this device, by the third party and
damage and injury caused by such abusive use㻌
e. Loss of the settings㻌
f. Other injuries and damages caused in relation to this device directly or indirectly㻌
㻌
1.5 Protection of Privacy Information
Within video information acquired with this device, the ones that can specify an individual person
are the personal information subject of “Act on the Protection of Personal Information.” Handle
such video information in accordance with the law.㻌
* Refer to the cases corresponding to the personal information specified in “guideline
concerning the Act on Protection of Personal Information relating to economy and industry” from
the Ministry of Economy, Trade and Industry.㻌
㻌
1.6 Cautions of Network Connection
This device is designed to be used by connecting to the network. To protect the system from the
damages specific to the network connection, take the sufficient security measures under the
responsibility of the customer.㻌
The network-specific damages include damages by leakage/outflow of the information acquired by
this device, unauthorized access, and the system stop. The measures include the followings;
however, the customer needs to take other sufficient measures under the customer’s
responsibility.㻌
- Do not place the device at a location, where the cable can be easily replaced.㻌
- Secure the network safety (firewall, etc.).㻌
- Periodically check for the virus on the connected PC.㻌
- Limit the users on the connected PC (setting a password, etc.).㻌
- Control as the authorized information do not leak.㻌
㻌
1.7 Limiting the Applications of the Device
The applications of this device are limited by “VC-1 and AVC/H.264 patent portfolio license relating
to the personal and non-commercial applications.”㻌
Follow this regulation and use this device for the personal applications and applications other than
the commercial uses.㻌
For details, please refer to http://www.mpegla.com㻚㻌
㻌
㻌
2 Installation
2.1 Names and Functions of Sections
䐟㻌
䐡
䐠
䐠
䐣㻌
䐢
䐤㻌
ձ Camera lower case
ղ Fixing screws for the camera upper and lower directions (2 pc)
ճ Internal cover
㻌
մ Fixing screws for the camera housing (2 pc)
յ Camera housing
ն Dome cover
㻌
㻌
㻌
㻌
㻌
㻌
Default
Reset
Video output
Pressing the button for five seconds or longer, the setting returns to
the factory default value.
Pressing the button restarts up the device.
Pressing this button connects the monitor output cable for the video
output signal.
䐟 Network video output terminal (RJ-45)㻌
Connect to the HUB compatible with PoE.㻌
䐠 LED㻌
Orange㻌 : It indicates that the data are transmitted/received between networks.
Green㻌 : It indicates the valid connection.
䐡 Block terminal block㻌
It is connected when the microphone/alarm is input.㻌
䐟㻌
䐠 䐡
㻌
㻌
㻌
㻌
㻌
2.2 Camera Installation
2.2.1 Removing the Camera Housing
Refer to the following figure and the procedure.㻌
a. Loosen two screws of the camera housing to remove the camera housing.㻌
b. Pull slowly to remove the internal cover.㻌
㻌
㻌
㻌
Before start removing the dome cover, be su re to turn off the power
Caution
supply first.
This device does not have a power supply switch. Leave the network cable
disconnected, or turn off the PoE HUB power supply.
㻌
2.2.2 Mounting the Camera
㻌
㻌
㻌
㻌
Step 1 Mounting the plastic anchor (supplied)
z By using the mounting template, put a mark at the mounting area for preparation.
㻝㻚 Put the supplied mounting template at the mounting surface. Open two 6-dia (0.2 inch) holes for
the supplied plastic anchor at the specified positions.
㻞㻚 Then, insert the plastic anchors (supplied) at the two holes.㻌
㻌
Step 2. Mounting method
z
After removing the camera housing by taking the previously described procedure, fix the camera to
the plastic anchor through two holes at the lower section of the camera by using the supplied TP4
tap screws (2 sets). Then, insert the network cable, audio, and alarm cable to the rear panel if
necessary.
㻌
㻌
Fix the camera to two anchors by
using the supplied screws (2 pc).㻌
㻌
z When connecting the drop preventing wire (not supplied), attach the one end of the drop preventing
wire to the mounting surface and attach the other end to the safety cord screw of the device.㻌
㻰㼞㼛㼜㻌㼜㼞㼑㼢㼑㼚㼠㼕㼚㼓㻌㼣㼕㼞㼑㻌
㻔㻺㼛㼠㻌㼟㼡㼜㼜㼘㼕㼑㼐㻕㻌
㻿㼍㼒㼑㼠㼥㻌㼏㼛㼞㼐㻌㼟㼏㼞㼑㼣㻌㼛㼒㻌㼠㼔㼑㻌
㼐㼑㼢㼕㼏㼑㻌
㻌
㻌
Depending on the material of the mounting surface, screws and anchors that are
different from the supplied ones may be required. To prevent falling of the device,
Warning
be sure to check that the device is fixed securely with the drop preventing wire
with the strength sufficient enough to keep the total weight of the device.
(Also pay close attention to the finishing process of the wire ends.)
㻌
㻌
㻌
It is necessary to connect one end of the drop preventing wire to the ceiling and
Caution
the other end to the safety cord screw of the device.
㻌
2.2.3 Adjusting the Angle
㻌
㻌
㻌
㻌
㻌
This device consists of three axes for lens positioning, which are the pan, tilt, and horizontal position.
z Pan adjustment (A)
When the camera is attached to the wall or the tilted ceiling, turn the lens table to adjust.㻌
z Tilt adjustment (B)
Loosen the fixing screw for camera up/down direction and change the camera position to fix.㻌
z Horizontal rotation (C)
Rotate the lens section to adjust the angle.㻌
Do not rotate the lens in excess of the rotation limit. Otherwise, the internal cable may be cut by
being twisted.㻌
㻌
Limits for three axes positions:㻌
y
Caution
Pan range: +/-175°
y
Tilt range: 15° to 90°
y
Horizontal rotation range: +/-175°
㻌
㻌
㻌
㻌
㻌
2.2.4 Adjusting Zoom and Focus
z
Adjustment is possible by the GUI menu settings. Please refer to the application part for details.
㻌
㻌
㻌
Manual adjustment is not possible.
Caution
㻌
㻌
If the lens is forcibly moved, please take note that the lens may get broken.
2.2.5 Mounting the Camera Housing
The internal cover and the camera housing can be fixed by tightening two screws for fixing the
housing.㻌
After mounting the device, turn on the power of PoE. When mounting the camera housing, position
as the detachable cover comes to the rear side, so the cable can be fed through.
(See the following figure.)㻌
㻌
㻌
㻌
㻌
㻹㼛㼐㼑㼘㻌㻌㻵㻺㻾㻙㻝㻜㻜㻤㻼
R
(
)
(
)
r
3 Connection
3.1 Camera Power Supply
This device can be connected to the network device that is compatible with the PoE standard
(IEEE802.3af compatible). Therefore, the power supply work for the camera is not necessary.
Connect the PoE power supply system (HUB, etc.) and the Ethernet cable (category 5 or higher) to
the network terminal.㻌
㻌
This device does not have a power supply switch. Pull out and insert the network cable or turn
on and off the power of the PoE power supply system.
[Important]㻌
Ɣ The maximum length of the Ethernet cable is 100m.㻌
Ɣ To reconnect the Ethernet cable, wait for a while.㻌
When the cable is connected immediately, there are cases that the power is not supplied from
the PoE power supply system.㻌
㻌
㻌
3.2 Example of Connection
Example of connection between this device and the network recorder (NVR)㻌
㻌
㻌
ġ IPD-DM300
㻌
㻌
㻌
ġ IPD-DM300
㻌
㻌
㻌
㻌
㻌
㻌
Ethernet cable
Category 5 or higher
IN
Ethernet cable
Category 5 or higher
-1008P or INR-1016P
HDMI monito
㻌 㻌
㻌
㻌
㻌
㻌
㻌
3.3 IP Address
When the IP camera is used, setting of the IP address is necessary.㻌
In this device, DHCP is valid by the default setting. When the DHCP server is provided in the
network, the IP address is automatically acquired. Therefore, it is not necessary to change the IP
address of the camera. When the DHCP server is not provided in the network, the default setting of
the camera is as follows.㻌
IP Address
Subnet mask
: 192.168.1.100
: 255.255.255.0
3.4 Logging In
㻝㻚 Start up the browser (Internet Explorer, etc.) and in the address bar, enter the IP address of the
network camera to change the setting.㻌
㻞㻚 Enter the user name and the password.㻌
User name
Password㻌:admin
㻟㻚 Click OK.㻌
㻌
:admin
4 Warranty and After-sales Service
㻌
This product is delivered with the warranty certificate (in this manual). Please receive the warranty
certificate at the time of purchase.㻌
Fill in the specified items and check the written items. Then keep in a safe place.㻌
Ɣ The warranty period is one year from the date of purchase. (However, it excludes consumables.)㻌
According to the warranty certificate,
certificate for the details.㻌
Ɣ For repairs after the end of warranty period, consult
functions can be kept working by being repaired, the product can be repaired with consideration
upon a request from the customer.㻌
Ɣ Before requesting the repair, please take some time and review the instruction manual. Check the
contents and tell us of the model name, purchased date, and status of the trouble as detailed as
possible.㻌
Ɣ For other details regarding the after-sale service, consult
㻌
* Be sure to conduct the maintenance inspections always at early timings.㻌
㻌
your dealer will repair the product. See the warranty
your dealer or the sales person. If the
your dealer or the sales person.㻌
5 Specifications/Exterior
5.1 Specifications
(1) Imaging element㻌㻌㻌㻌1/3 type CMOS sensor㻌
(2) Scanning method㻌㻌 㻌 Progressive scan㻌
(3) Synchronizing method㻌㻌 Internal synchronization: Crystal-lock㻌
(4) Analog video output㻌㻌 㻌㻌㻌 VBS 1.0 Vp-p/75ȍ (for angle adjustment)㻌
(5) S/N ratio㻌㻌㻌㻌㻌50 dB (p-p/rms) or higher㻌
(6) Lowest object illuminance㻌㻌 (Color)㻌 2.00Lx/F1.2㻌 (Electron sensitivity OFF, VBS output 50%)㻌
㻌㻌㻌㻌㻌㻌㻌㻌㻌
(7) WDR function㻌㻌㻌㻌Yes㻌
(8) AGC㻌㻌㻌㻌㻌㻌Yes㻌
(9) Electron sensitivity㻌㻌 㻌 Yes, Switching between ON/OFF㻌
(10)
Switching between day and night
(11) Automatic iris function㻌㻌 Corresponding to DC iris㻌
(12) DETAIL correction㻌㻌 㻌 Yes㻌
(13) White balance㻌㻌㻌㻌ATW/Manual selection㻌
(14) Privacy mask㻌㻌㻌㻌Yes (setting possible up to the max. of 4 sections)㻌
(15) Noise reduction㻌㻌㻌㻌Yes (level adjustment possible)㻌
(16) Camera ID㻌㻌㻌㻌㻌Yes㻌
(17) Video setting㻌㻌㻌㻌Two-pattern setting possible㻌
- Compression method㻌㻌 H.264 or MJPEG㻌
- Image size㻌㻌㻌㻌
- Frame rate㻌㻌㻌㻌Max. 30 fps㻌
- Bit rate (H.264)㻌㻌 㻌 256 Kbps to 12 Mbps (Only H.264 is valid)㻌
- Image setting (MJPEG)㻌 Yes (Only MJPEG is valid)㻌
- Transmission mode㻌㻌 H.264: CBR / MJPEG: VBR㻌
(18) Motion detection㻌㻌㻌㻌Yes (mask setting possible)㻌
(19) Audio function㻌㻌㻌㻌Yes (one line)㻌
- Input level㻌㻌㻌㻌-20 dB㻌
- Input impedance㻌㻌 㻌 2 kȍ㻌
(20) Network㻌㻌㻌㻌㻌Ethernet 10Base-T/100Base-TX㻌
(21) Protocol㻌 TCP, UDP, RTP/RTCP/RTSP, HTTP, HTTPS, FTP, NTP, ICMP,
(22) Built-in lens㻌
- Focusing distance (f)㻌㻌 3.0 to 9.0 mm
-
Maximum aperture ratio (F)㻌1.2
- Angle (H)㻌㻌㻌㻌㻌28.0° to 78.0°
(23) Dome cover㻌㻌㻌㻌㻌Smoke
(24) Power supply㻌㻌㻌㻌PoE (IEEE 802.3af) CLASS 0㻌
(25) Power consumption㻌㻌 㻌 Approx. 4.5W㻌
(26) Operating ambient Within -10 to + 50°C/30 to 90 %RH (no condensation)㻌
temperature/humidity㻌㻌 㻌
(Black and white)㻌0.25Lx/F1.2㻌(Electron sensitivity OFF, VBS output 25%)
㻌 Corresponding to True Day/Night, Switching between auto/manual㻌
1920 x 1080/1280 x 960/1280 x 720/640 x 480/640 x 360/320 x 240/320 x 176
IGMP, IPv4, ARP, DHCP, DNS㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
(27) Exterior dimension (Dia. x H)㻌 125 dia. x 106 mm (projection section excluded)
(28) Mass㻌㻌㻌㻌㻌㻌Approx. 520g㻌
(29) Input/output connector㻌㻌 - ETHERNET㻌㻌㻦㻌RJ-45 (Auto-MDI/MDIX)㻌
㻌㻌㻌㻌㻌㻌㻌㻌- VIDEO OUT㻌㻌: Connector output (for angle adjustment)㻌
(BNC output possible by using the attached
monitor output cable)㻌
㻌㻌㻌㻌㻌㻌㻌㻌- MIC/ALARM㻌㻌 : 8P block terminal block㻌
㻌
㻌
5.2 Exterior
㻌
㼁㼚㼕㼠㻦㻌㼙㼙㻌
<< Memo >>㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
㻌
ڦ
ڦ
ڦ
Ikegami Electronics (U.S.A.), Inc.
37 Brook Avenue, Maywood, N.J. 07607, U.S.A.
Phone: (201) 368-9171, FAX (201) 569-1626
www.ikegami.com
Ikegami Electronics (Europe) GmbH
Ikegami Strasse 1, D-41460 Neuss, Germany
Phone: 02131-123-0, FAX 02131-102820
www.ikegami.de
Ikegami Electronics U.K. Office:
Unit E1, Cologne Court, Brooklands Close,
Windmill Road, Sunbury-on-Thames,
Middlesex, TW16 7EB, U.K.
Phone: 01932-769700 FAX 01-92-769710
www.ikegami.co.uk
or
㻌
㻌
TCB004645-01
Ikegami Tsushinki Co., Ltd.
Loading...