IKEA UPPLEVA 46, UPPLEVA 32 User Manual [dk]

UPPLEVA 32-46"

Design a nd Qualit y

IKEA of Sw eden

AV 1

adapter

INITIAL SETUP

OPTIONS

SETUP

LOCK

PAP

SOU ND

MEDIA

SMART TV

PICTU RE

Welcome to use the Wizard for Initial Setup !!

Please press [OK] to start the wizard.

WELCOME

SETUP

BACK

EXIT

Enter

Select

Back

Exit

CHANNEL INS TALL

Automatic Search ...

Automatic Update ...

Analogue Manual Scan ...

Antenna Manual Installation ...

Clean Channel L ist ...

OPTIONS

BACK

EXIT

Location Home

Software Update ...

HBBTV mode On

DivX

Timer

Enter

Select

Back

Exit

Figure 1

Figure 3

Registration ...

Deregistra tion ...

Figure 5

Figure 2

SUBTITLE

Subtitle On

Digital Subtitle La nguage English

OPTIONS

BACK

EXIT

Digital Subtitle La nguage 2nd English

Subtitle Type Normal

Select

Back

Exit

Figure 4

...

ENGLISH 4 DANSK 24 SUOMI 44 SVENSKA 64

ENGLISH

Important information Safety

Ensure that your domestic mains supply voltage matches the voltage indicated on

the identication sticker located at the back of your set. Where the mains plug or

an appliance coupler is used as disconnect device, the disconnect device shall remain

readily operable.

On certain models, the light indicator

is located at the side of the TV set. The

absence of a light indication at the front does not mean that the TV set is fully

disconnected from the mains. To disconnect

the TV set completely, the mains plug must

be pulled out.

The TV set’s components are sensitive

to heat. The maximum ambient temperature should not exceed 35º

Celsius. Do not cover the vents at the back or sides of the TV set. Leave sufcient space around it to allow adequate ventilation.

Install the appliance away from any source

of heat (replace, ...) or appliances creating strong magnetic or electric elds.

Moisture in rooms where the set is

installed should not exceed 85% humidity.

Apparatus shall not be exposed to dripping or splashing and no objects

lled with liquids, such as vases, shall

be placed on the apparatus. Moving the set

from a cold place to a warm one can cause condensation on the screen (and on some

components inside the TV set). Let the

condensation evaporate before switching the

TV set on again.

WARNING

To prevent the spread of re, keep candles or other open ames away from this product at all times.

, switch it off completely by removing

time

the plug from the mains power socket.

During thunderstorms, we recommend that you disconnect the TV set from the mains and aerial so that it is not affected by electrical or electromagnetic surges that

could damage it. For this reason, keep the

mains and aerial sockets accessible so they can be disconnected, if necessary.

Unplug the TV set immediately if you notice it giving off a smell of burning or smoke. You must never, under any circumstances,

open the TV set yourself, as you run the risk

of an electric shock in doing so.

TV screen

The TV screen used in this product is made

of glass. Therefore, it can break when the

product is dropped or impacted upon by

other objects.

The TV screen is a very high technology

product, giving you nely detailed pictures.

Occasionally, a few nonactive pixels may

appear on the screen as a xed point of blue, green or red. This does not affect the performance of your product.

Care

Use a glass-cleaning product to clean the screen and a soft cloth and mild detergent

to clean the rest of the set.

Important: Using strong detergents, alcohol-based and abrasive products may

damage the screen.

Dust the vents at the back and sides regularly. Using solvents, abrasive or

alcohol-based products could damage the

TV set. If an object or liquid enters inside

the appliance, unplug it immediately and

have it checked by an authorized engineer.

Never open the appliance yourself since

this may put you at risk or damage the appliance.

The or or the button on the remote control can be used to switch it on and put it into

standby mode.

watching the TV for a lengthy period of

POWER

/ button on the TV set

If you are not going to be

Hanging the TV set on the wall

WARNING: This operation requires two

people.

To ensure a safe installation, observe the following safety notes:

─ Check that the wall can support the

weight of the TV set and wall mount

assembly.

─ Follow the mounting instructions

provided with the wall mount. For certain models, make sure to screw the

hexagonal VESA wall mounting screw

bosses (and screws) provided with the

set into the nuts for the wall mount at

the back of your set before your wall mounting.

─ The TV set must be installed on a

vertical wall.

─ Make sure to use only screws suitable

for the material of the wall.

─ Make sure that the TV set cables are

placed so that there is not danger of

tripping over them.

All other safety instructions about our TV

sets are also applicable here.

This product is designed and manufactured with high quality materials and components

which can be recycled and reused. This

symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste to prevent potential negative consequences for the environment and

human health. Please, dispose of this

equipment at your local community waste

collection/recycling centre. In the European

Union there are separate collection systems

for used electrical and electronic product. Please, help us to conserve the environment

we live in!

Handling the TV set on the table

Before setting up your television set, make

sure that the surface you want to put the

set on can support its weight.

Don’t place the set on an unstable surface

(e.g. moving shelf, very edge of a unit) and make sure that the front of the television

set does not overhang the surface it is

sitting on.

Remote control functions

Most of your TV's functions are available via the menus that appear on the screen. The

remote control supplied with your TV can be used to navigate through the menus and to

congure all the general settings.

Standby / quit standby.

11 12

To switch the remote for TV use.

3. BACK

To return to the previous menu.

To return to the previous channel.

To navigate through the menus. To set functions and change values.

can also be used to open the

corresponding submenu.

5. E X I T/

To exit the menu structure or Teletex t; to stop some functions.

To fast forward or reverse (press and

hold in Media function);and to move

to the previous or next photo, song or video.

7. CH+/-

To change channels.

8. Colour buttons

To select tasks or Teletext pages. The

red but ton can also be used for MHEG

function.

27 28 29

9. MUTE

To switch the sound off and back on again.

31 32

10. R EC

To record programme.

11. I PT V

No function.

12. S UBT

To select a subtitle language available

for selected digital TV programme.

13. GUI DE

To toggle the Electronic Programme

Guide on or off (only available for digital channels).

14. 0 -9

To enter channel numbers.

To enter a letter, a digit or a symbol in some functions.

15. DISK MEN U

No function.

16. S OUN D

To select a preset sound mode.

17.

To switch the remote for sound system use.

18. MENU

To access the main menu.

To access or exit the virtual keyboard in smart TV function.

19. OK

To conrm an entry or selection. To freeze/unfreeze the picture in digital TV mode.

25. OPTION

To display the function menu.To perform certain operations. To display the Teletext page in different modes.

26. SOURC E

To select connected devices.

27. EC O

To select desired power saving mode.

28. INFO

To display programme information, if available.

29. CH.LIST

To d ispl ay the channel list.

30. TEXT/MEDIA CENTER

To toggle Teletext on or off.

31. RE PE AT

No function.

32.

To select the picture format.

Note: We recommended you use the full screen mode. Do not use the display mode with black bars on both sides of the picture (such as 4:3) for a prolonged period of time; this may result in permanent damage to the TV screen may be damaged permanently.

20.

To navigate through the menus. To select menu options.

21. SMART TV

To display the smart TV homepage.

22.

To play/pause.

2 3 . V O L +/-

To control the volume.

24. LANG

To select a sound type available for selected Analogue T V programme. To select an audio language available for selected digital TV programme.

Connect the power and antenna

To switch on the TV after connecting the power cord, press or POWER/ .

Note: The location of the power socket varies depending on the TV model.

On some models, you have to turn on the power switch rst.

Cable

Game console, PC

Antenna/Cable

input

Note: Before connecting a PC, set the PC monitor refresh rate to 60Hz.

LAN

AV 1

adapter

VGA

Network connection

AV 2

adapter

VGA

audio in

Game console

Or use an HDMI connection.

DVD player, home theatre system

DVD player/ Home theatre system

CMP

adapter

AUDIO in

adapter

Pr Pb Y R L

OUT

Blu-ray Disc player, headphones, HD game console & HD camcorder

Notes:

─ USB connectors are for data input from

USB storage devices. Only USB 1 port can be connected to your USB memory stick.

─ Exposure to excessive sound levels from

earphones and headphones can result in hearing loss.

─ Number of HDMI may vary. ─ ARC (Audio Return Channel) function is

COMMON

INTERFACE

only supported on HDMI 4 (ARC) port. It is recommended to connect your home theatre to the HDMI ARC connector to send sound from the TV to the sound system via an HDMI cable.

HDMI 1

HDMI 2

HD Camcorder

HDMI 3

USB

Blu-ray Disc player

HD game console

DVD player, cable receiver Note:

Remove the power cord before connecting devices.

CMP

adapter

AUDIO in

adapter

Antenna/Cable

input

Pr Pb Y R L

OUT

Set-top box

Cable

Pr Pb Y R L

OUT

Notes:

─ These illustrations are for reference only.

Your model may differ in appearance or may not include all connections shown.

─ The location of the power socket on the

TV may vary depending on the model.

─ The location and names of the function

buttons and connectors on the TV may vary depending on the model.

DVD recorder

Important:

If the remote control is not used for a long period, remove the batteries and store

them properly. Handle damaged or leaking batteries carefully. If your remote control

has two batteries, do not mix new and old

batteries. Batteries shall not be exposed to excessive heat such as sunshine, re or the like. Danger of explosion if battery is incorrectly replaced. Replace only with the

same or equivalent type recommended by

the manufacturer. Discard used batteries according to manufacturer’s instructions. Refer to your local recycling or waste

disposal rules and contact a local waste

disposal vendor to dispose of used batteries.

If the batteries in your remote control are run down you can use the buttons on

your TV. In TV mode, they have the same

functions as the corresponding buttons on

the remote control. In the menus they have

the following functions:

CH CH VOL VOL MENU/ MENU

OK/

Switch the TV on and off

1. When powered on, the TV will be turned on directly or be in standby mode. If

the TV is in standby mode, press the or POWER/ button on the TV or the

button on the remote control to turn

it on.

2. To put the TV into standby mode, press

the or POWER/ button on the TV or the button on the remote control. The TV remains powered up, but with low

energy consumption.

3. To switch the TV off, unplug the mains plug from the mains outlet.

(*On certain models, you have to turn on

the power switch rst.)

Initial setup

Initial setup involves selecting all the settings required to be able to search for and store all the Analogue and digital

channels you can receive.

Make sure the TV is switched on and follow all the steps below in the order given.

Note: If the channel search retrieved only the analogue channels it could be caused by weak broadcasting signals and therefore is not covered by the manufacturer warranty. Manufacturers cannot be held responsible for the lack of or weak broadcasting signals that can be found in some areas.

The rst time you switch the TV on, the Initial Setup wizard opens, which guides you through the initial setup process. (Refer to Figure 1.) Press OK to start your initial setup.

1. Press / to select your language, then press OK/ to enter the next step.

2. Press / to select your country, then press OK/ to enter the next step.

Note: If you select France, you will have to enter the Password Setting menu here in order to set a password. Use the digit buttons to enter a four-digit number for your password. (0000 is too simple to be set as your password.) Re-enter the same code

to conrm the password. After that, you will

enter the next step automatically. (In this step, you can only press BACK to return to the previous step.)

3. Press / to select your tuner mode Antenna or Cable or Satellite. (Note:

For some models, this option may not be available.)

─ Select Antenna.

• Press OK/ to enter.

• Select Digital & Analogue, Digital or Analogue, then press OK/ .

• Press / to select Scan, then press

OK/ to start the automatic search for all

DVB-T digital and/or analogue channels.

─ Select Cable.

• Press OK/ to enter.

• Select Digital & Analogue, Digital or Analogue, then press OK/ .

• Press / to select Scan, then press

OK/ to directly start your initial setup or

enter below step.

• Select Full if available to search for and store all DVB-C digital and analogue

channels.

• You may select another advanced scan mode if available (for example,

Advanced), then congure proper cable information as described below. Use the

digit buttons to adjust the values for

frequency, symbol rate and network ID;

use / to select a modulation mode.

• Press OK to start initial setup relating to

all DVB-C digital and analogue channels.

Note: For some models, this option may not be available.

─ Select Satellite.

• Press OK/ to enter.

• Press / to select Scan, then press

OK/ to enter the next step to congure

proper information relating to satellite and

antenna.

• Press OK to start initial setup relating to all satellite channels.

Note: To prevent the channel setup process from being interrupted, wait for the message indicating that the setup is complete.

4. Before starting the scanning, you can also select Skip Scan to skip the initial

setup process.

5. During the setup, you can follow the

instructions at the bottom of the screen and return to the previous step by pressing BACK. Or press EXIT to exit or

interrupt the search halfway.

6. Once the automatic search ends, the TV enters the next step automatically. Press / to select your location Shop or Home. Press OK/ to conrm your selection and enter the last step.

─ In this step, you can press OK to exit

the initial setup. The channels are arranged in a preset order. If you wish to skip channels, modify the preset order

or rename channels, select SETUP > Organiser and press OK/ to enter.

─ In this step, you can also press BACK to

return to the previous step.

Automatically install channels

This section describes how to search and

store channels automatically. Instructions are for both analogue and digital channels.

1. Press MENU on the remote control and

select SETUP > Language > Menu Language. Press / to select your

desired menu language.

2. Press BACK to return to SETUP, press

/ to select Country, then press

/ to select your country. The TV

installs and arranges channels according

to your country.

3. Press / to select Tuner Mode, then

press / to select Antenna, Cable or Satellite.

(For some models, this option may not be avialable.)

─ Select Antenna.

• Press / to select Channel Install, and press OK/ to enter.

• Select Automatic Search (Refer to Figure 2.), then press OK/ to display

Automatic Search.

• Press OK to skip the country selection and enter the next step. Or use / to

reselect your country, then press OK to

enter.

• Select Digital & Analogue, Digital or Analogue, then press OK/ to start the

automatic search, which relates to all

DVB-T digital and/or analogue channels.

─ Select Cable.

• Press / to select Channel Install, and press OK/ to enter.

• Select Automatic Search, then press

OK/ to display Automatic Search.

• Press OK to skip the country selection and enter the next step. Or use / to reselect your country, then press OK to

enter.

─ Select Digital & Analogue, then press

OK/ to enter. Select your scan mode

if available and congure proper cable

information in the same way as in Initial setup. Select Scan and press OK/ to start your automatic search relating to

all DVB-C digital and analogue channels.

─ Select Digital, then follow the same

process as above to start your automatic search relating to all DVB-C digital

channels.

─ Select Analogue, then press OK/ to

start your automatic search relating to

all analogue channels.

─ Select Satellite.

Note: For some models, this option may not be available.

• Press / to select Satellite Setup, and press OK/ to enter.

• Press / to select a proper satellite or add new satellites if needed, then press OK to enter and congure proper information relating to satellite and

antenna.

• Select SETUP > Channel Install > Automatic Search, then press

OK/ to enter.

─ Select Country, and use / to reselect

your desired country, if necessary.

─ Select Satellite Tuning, press

OK/ to display the SATELLITE

TUNING menu. Congure the proper information. Select Scan, and press

OK/ to start initial setup relating to all

satellite channels.

Note: For some models, this option may not be available.

4. The search may take a few minutes.

During the process, you can press EXIT

to abort halfway.

5. Once the automatic search ends, press

BACK to return to the previous step or press OK to restart your channel search.

6. After the automatic search, channels are arranged in a preset order. You can skip

channels, modify the preset order or

rename channels.

Use your TV Access channels

Using the digit buttons: press the

corresponding digit buttons to access the

channels.

Using the CH+/- or CH / buttons:

scroll through the channels.

Watch connected devices

Repeatedly press SOURCE on the remote control or OK on the TV to toggle between

TV and other input sources. To resume TV

viewing, press any digit button to enter the channel, while CH+/- will cycle through all

TV channels and other input sources.

Note: Not all models have an OK button on the TV.

4. Press BACK to return to the previous menu.

5. Press EXIT to close the menu.

Note: Some options may not be available for certain signal sources.

Select menu language

You can choose your preferred menu

language following the instructions below.

1. Press MENU to display the main menu.

2. Press / / / to select SETUP, then press OK to enter.

3. Select Language and press OK/ to enter.

4. Select Menu Language and press

/ to select your desired language to

display the menus.

5. Press EXIT to close the menu.

Use more of your TV

Setup your favourite channels

You can create a list of your favourite TV

channels.

1. Press CH.LIST.

2. Press the yellow button to enter

CHANNEL LIST SELECTION. Press

/ to select the favourite list and

press OK to enter.

3. Press the blue button to start editing your favourite list. Press / to scroll

through the channel list and press OK to

select or deselect it.

4. Repeat this procedure to setup other favourite channels.

5. Press CH.LIST/EXIT to exit.

Volume

Volume control: use the VOL / buttons on the TV or VOL+/- buttons on the remote control to increase or decrease the volume.

Sound mute: press the MUTE button to

temporarily mute the sound. Press this

button again or the VOL+ button to restore

it.

Use TV menus

1. Press MENU to display the main menu. (Refer to Figure 3.)

2. Press / / / to select the desired

item, then press OK to open the

corresponding submenu.

3. In submenus, use / to select menu

options, use / to set functions or

change values. Use OK to activate a setting. Use OK/ to open the corresponding submenu.

Energy Saving

1. Press MENU on the remote control and

select PICTURE > ECO Settings >

Energy Saving.

2. Press / to select desired power

saving mode to achieve the desired

power saving effect.

3. Press EXIT to close the menu.

Shortcut operation: Press ECO on the remote control to select desired power

saving mode directly.

PAP function

To display the pictures from different source

inputs side by side. Note that one window

is for both analogue and digital TV inputs,

the other is for VGA, HDMI and CMP inputs.

(Note: Not available for AV-Scart on both windows.)

1. Press MENU to display the main menu.

2. Select PAP and press OK to enter.

3. Select the PAP option, and press / to turn on/off PAP function.

4. Select TV Position, press / to reposition the TV window.

5. Press / to toggle the focus window.

6. When the focus is on the TV window, the digit buttons and CH+/- work in TV. When the focus is on the other window,

CH+/- switches available external

sources.

Use subtitles

You can enable subtitles for each TV

channel. Subtitles are broadcast via Teletext or DVB-T/DVB-C digital broadcasts. With

digital broadcasts, you have the additional option of selecting a preferred subtitle

language.

Turn on/off subtitles

1. Press MENU on the remote control and select OPTIONS > Subtitle.

2. Press OK/ to enter. (Refer to Figure

4.)

3. Select the Subtitle option, and press

/ to select On/Off to turn on/off

subtitles.

Enable subtitle languages on digital TV channels

1. Press MENU on the remote control and select OPTIONS > Subtitle > Digital

Subtitle Language.

2. Press / to select a subtitle language as your preferred language.

3. Press / to select Digital Subtitle

Language 2nd.

4. Press / to select a secondary subtitle language.

5. Press EXIT to close the menu.

Shortcut operation: Press SUBT on the remote control to directly select a subtitle language available for the selected digital TV

programme.

Select a subtitle type on digital TV channels

1. Press MENU on the remote control and select OPTIONS > Subtitle > Subtitle

Type.

2. Press / to select a subtitle type. You

can select Hearing Impaired to display the hearing impaired subtitles with your

selected language.

Select decoding page language in Teletext

Press MENU on the remote control and selec t OPTIONS > Teletext > Decoding

Page Language. Select a proper type of language in which Teletext will display.

Digital Teletext language

For digital TV channels, your TV could zap

to a service with multiple initial Teletext

pages in different languages. This function

allows you to select an available language as primary language, which relates to different

initial Teletext pages.

Press MENU on the remote control and

selec t OPTIONS > Teletext > Digital Teletext Language. Press / to select.

SPDIF type

Connec t to an audio device through the SPDIF output. Press MENU on the remote control and select OPTIONS > SPDIF

Typ e. Select a proper sound type from the list for digital programmes.

─ If the current programme outputs sound

in Dolby D format, then either PCM or

Dolby D can be selected.

─ If the current programme does not

output sound in Dolby D format, only

PCM can be selected. Otherwise no sound will be output.

─ Select Off to turn off the audio output

from the audio device connected to the

SPDIF output.

Note: The options you may choose depend on the programme you are watching. If you select PCM and the sound is ahead of the picture, you can

select SPDIF Delay from the OPTIONS

menu and press / to adjust the delay time to synchronize the sound with the picture.

T-Link

To search for CEC devices connected to the

HDMI sockets in your TV and enable one-

touch play and one-touch standby between

CEC devices.

Enable or disable T-Link

1. Press MENU on the remote control, then select OPTIONS > T-Link.

2. Press / to select On or Off.

Use one-touch play

One-touch play enables you to press the play button on, for example, your DVD

remote control. This starts playback on your

DVD device and automatically switches your TV to the correct source, displaying DVD

content.

Use system standby

System standby enables you to press the

button on, for example, your TV remote

control. This switches your TV and all connected HDMI devices to standby mode.

Network update

Press MENU on the remote control, then selec t OPTIONS > Network Update. Select On/Of f to enable or disable the

Network update function.

─ When this function is on, the TV will

automatically update channels if your DTV service provider updates his DTV

network.

─ When this function is off, you need to

run the channel search again to get new channels or remove unavailable channels if your DTV service provider adds or removes channels from their

DTV network.

Common interface

Encrypted digital TV channels can be decoded with a common interface module and a card provided by a digital TV service

operator.

The common interface module may enable several digital services, depending on the operator and services you choose (for

example, pay TV). Contact your digital TV

service operator for more information about

services and terms.

Use the common interface module

WARNING: Switch off your TV before

inserting a common interface module.

Be sure to follow the instruction described below. Wrong insertion of a

common interface module may damage both the module and your TV.

1. Following the directions printed on the

common interface module, gently insert the module into the common interface

slot on the TV.

2. Push the module in as far as it will go.

3. Turn on the TV and wait for the common

interface function to be activated. This may take several minutes.

Note: Do not remove the common interface module from the slot. Removing the module will deactivate the digital services.

Access common interface services

After inserting and activating the common interface module, press MENU on the remote control and select OPTIONS >

Common Interface.

This menu option is only available if the common interface module is correctly

inserted and activated. On-screen

applications and content are provided by

your digital TV service operator.

Software update

Press MENU on the remote control and selec t OPTIONS > Software Update.

Press OK/ to enter.

─ Current Version: Checks the current

version of the software.

─ Product Name: Displays the product

name of your TV.

─ Serial Number(if available): Displays

the serial number of your TV.

─ By Network: Enables you to download

and install the latest software version

from the Internet. Make sure to set up a wired or wireless network connection rst, then select By Network and press OK/ to enter. Follow the on-screen instructions to continue.

Note: Connect a USB device to your TV before you start software update.

─ By Channel: Enables you to install the

latest version of the software if available.

Select By Channel and press OK/ to

enter.

─ Use / to select Yes under Auto

Download to automatically download

the latest software if available. After

the software has been downloaded successfully, you will be prompted to

decide if you want to install it right now.

If yes, follow the on-screen instructions

to complete your installation. You can

also select to ignore the installation

here.

• Select No under Auto Download to decline the automatic download.

• Select Manual Download and press

OK/ to start manual scanning the

latest software. Follow the on-screen

instructions to complete. During the scan,

press OK/EXIT to cancel or exit the

process.

Change to Shop or Home mode

1. Press MENU on the remote control and select OPTIONS > Location.

2. Press / to select your location Shop or Home.

3. Press EXIT to exit.

Note: According to the regulation of European Commission 2009/125/EC, in Home mode the TV will be put into standby mode automatically if there is no operation in 4 hours. This feature can be deactivated in OPTIONS menu.

MHEG function

Some digital TV broadcasters offer dedicated digital text or interactive services (for

example, BBC1). These services work like

normal Teletext with the addition of number,

colour and navigation buttons.

1. Press MENU on the remote control and select OPTIONS > Subtitle > Subtitle.

2. Press / to set Subtitle to Off.

Note: MHEG and subtitles are mutually exclusive and cannot coexist on the same screen. If Subtitle is set to On, MHEG will not appear.

3. Press the red button or TEXT on the remote control.

4. Press / / / to select or highlight items.

5. Press OK to conrm or activate.

6. Press one of the colour buttons to select an option.

7. Press TEXT or EXIT to exit.

View photos, play music and watch videos from a USB memory stick

Your TV is tted with a USB connector that

enables you to view photos, listen to music or watch videos stored on a USB storage

device. Supported le formats: Photo JPEG Music MP3 Video AVI, MP4, MPG, MPEG, TS, DIVX,

MKV…

Notes: Some USB keys and USB products like digital cameras or mobile phones are not fully compatible with USB 2.0 standard so they may not work with the TV multimedia player. Not all USB keys or devices are

compatible with the USB function. Not all above formats are supported. The encoding

formats of your les will determine whether

or not they can be used.

When a USB device is detected, it enters the

MEDIA menu directly. (Alternative: Select MEDIA in the main menu and press OK to

enter.)

Photo

To display photos, if available.

1. Select MEDIA > PHOTO, then press OK to enter the main le content browser.

2. In the main le content browser,

use / / / to select a photo or an

inner le folder.

3. Select an inner le folder, press OK to enter a sub le content browser.

4. Use / / to select a photo in either main or sub le content browser, press

MENU to display the photo menu in

folder mode.

─ Sort: Sort folders and photos by

modication Date or Name.

─ Edit: Copy, paste or delete a selected

photo.

─ Parser: You can select Recursive to

display photos from all sub le folders.

5. Select a photo, press OK to watch, and

a slide show begins from the selected

photo. Press to pause the photo if you want to rotate the paused photo. Press

MENU to display the photo menu in the

browser mode. You can play, pause or

rotate the photo, select different play

modes and displaying effects, etc.

6. Press the related buttons on the

remote control to perform the available functions shown on the function bar at

the bottom of the TV screen.

Music

To playback music, if available.

1. Select MEDIA > MUSIC, then press OK to enter the main le content browser.

2. Use / / / to select a song in either main or sub le content browser in the

same way as in photo display function, press MENU to display the music menu

in folder mode.

─ Sort: Sort folders and songs by Name,

Genre, Artist or Album.

─ Edit: Copy, paste or delete a selected

song.

─ Parser: You can select Recursive to

display songs from all sub le folders.

3. Select a song, press OK to play, and automatic playback begins from the selected song. Press MENU to display the music menu in the browser mode.

You can play or pause the song, select

different play modes, etc.

─ Show Lyrics: This option is available for

the songs with lyrics. Select it and use

/ to turn on/off lyrics synchronized

display.

─ Audio Only: Select and press OK to

listen to the music with the screen

turned off. Any key press will turn the screen on.

4. Press the related buttons on the

remote control to perform the available functions shown on the function bar at

the bottom of the TV screen.

Video

To watch videos, if available.

1. Select MEDIA > VIDEO, then press OK to enter the main le content browser.

2. Use / / / to select a video in either main or sub le content browser in the

same way as in photo display function, press MENU to display the video menu

in folder mode.

─ Sort: Sort folders and videos by Type,

modication Date or Name.

─ Edit: Copy, paste or delete a selected

video.

─ Parser: You can select Recursive to

display videos from all sub le folders.

3. Select a video, press OK to watch, and automatic playback begins from the selected video. Press MENU to display the video menu in the browser mode.

You can play or pause the video, select different play modes, screen modes and

preset picture settings, etc.

4. Press the related buttons on the

remote control to perform the available functions shown on the function bar at

the bottom of the TV screen.

DivX video

(* not available for some models)

ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an ofcial DivX Certied® device that plays DivX video. Visit divx.com for more

information and software tools to convert

your les into DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certied® device must be registered in order to play purchased DivX Video-onDemand (VOD) movies.

Obtain your registration code:

• Press MENU on the remote control.

• Select OPTIONS > DivX(R)

Registration.

• Press OK/ and your registration code will be displayed.

Go to vod.divx.com for more information on how to complete your registration.

Deregister your TV:

If you wish to deregister your TV,

• Press MENU on the remote control.

• Select OPTIONS > DivX(R)

Deregistration.

• Press OK/ and a message will guide you.

DivX®, DivX Certied® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.

Time detection

You can detect the time from digital

channels through following operations.

1. Press MENU on the remote control and

select OPTIONS >Timer > Clock > Auto Synchronization.

2. Press / to select On.

Assign a channel decoder

Decoders that decode analogue channels

can be connected to the AV connector.

Assign the TV channel as a channel to be

decoded. Then assign the connection where the decoder is connected.

1. Press MENU on the remote control and select SETUP > Decode.

2. Press OK/ to enter the list.

3. Press / to select the channel to decode.

4. Press OK to select or unselect the channel.

5. Press BACK to return to the previous menu.

Diagnostics on digital TV channels

1. Press MENU on the remote control and select SETUP > Diagnostics.

2. Press OK/ to display some signal information on the current digital channel, such as signal strength,

frequency, etc.

Time Shift

Allows you to pause, rewind and forward

in a programme. The rst time you use this function, make sure to connect a USB memory stick.

Note: Due to specic country requirements,

the Time Shift function is not available for Finland.

1. Press MENU on the remote control and select SETUP > Time Shift.

2. Press / to select On to switch on the Time Shift function, then press EXIT to

close the menu.

3. Press OPTION on the remote control

and select Time Shift, then press OK to

conrm.

4. Follow the directions on the screen to do the setup.

5. After the disk setup is done, press

OPTION and select Time Shift.

6. Press OK to display the Time Shift menu.

─ Press the button to pause the picture

and begin the Time Shift.

─ Press the button to play the recorded

part.

─ When the Time Shift menu disappears

and only the timing of the Time Shift remains on the screen, you can press the button or OK to access the Time

Shift menu.

─ Press the button to fast backward or

the button to fast forward.

─ Press the button to quit the Time Shift

function.

Notes:

─ Before you connect the USB memory

stick to the TV, make sure you have backed up the data in the device to avoid the risk of losing important data due to unforeseen malfunction.

─ We recommend you use a USB device

with free capacity above 1GB and disk speed faster than 5.0MB/sec.

─ The bigger the le size for Time Shift,

the longer the recording time.

─ If you change the channel in Time Shift

mode, a message prompts you to select Yes or No. You can select Yes to exit the Time Shift function and execute the channel change.

Reset shop

Allows you to reset the TV to factory default

settings.

1. Press MENU on the remote control and select SETUP, then press OK to conrm.

2. Select Reset Shop and press OK/ to enter.

3. Use the digit buttons to enter the password.

4. Press / to select OK and press OK to conrm.

5. The Initial Setup menu appears. Follow the related instructions.

Customising the input settings

Allows you to congure your TV for external

input devices, such as a set-top box, Blu-

Ray player, computer or game console.

1. Press MENU on the remote control and select SETUP > Input Settings.

2. Press OK/ to enter Input Settings.

3. Press / to select the port the input device is connected to.

4. Press / to select the type of device. Press / to assign a name to the device.

5. Press BACK to return to the SETUP

menu.

After conguring, the selected source label

will be displayed after the name of the related connector in the source list when pressing SOURCE on the remote control or

OK on the TV.

Use Electronic programme guide

EPG is an on-screen guide that displays scheduled TV programmes. You can

navigate, select, view and record

programmes.

1. Press GUIDE on the remote control, the

Now and Next EPG menu will appear, which allows you to get information about the current or next programme

playing on each channel. Navigate

through the different programmes using the navigation buttons on the remote

control.

2. Use the colour buttons to view the

8 Days EPG.

─ Prev Day (Red): List the previous day’s

EPG.

─ Next Day (Green): List the next day’s

EPG.

─ View Detail (Yellow): Display the

description of this programme if

available.

─ Type Filter (Blue): Programme guide

lter for digital TV programmes.

• Press the blue button to display the programmes’ type and subtype lists.

• Navigate through the different types and subtypes using the navigation buttons on

the remote control.

• Select one or more types, which you want to highlight from the Type list, press

OK to select (or deselect). A checkmark

will appear to the left of the type when

selected. When you select a type, all its subtypes will be selected accordingly.

• Also, you can select some desired subtypes without selecting any type rst.

• Press the blue button to exit the type and subtype list.

• After ltering, all your desired digital TV programmes will be highlighted.

─ Add Schedule (Option): Press OPTION

on the remote control to bring up the Schedule List menu. For details on scheduled recording, refer to the

Schedule List section.

3. Press GUIDE/EXIT to exit the EPG and switch to the selected channel.

PVR(Personal Video Recorder)

Allows you to record your favourite TV

programme. Before you use the function, connect a USB-memory stick to the set rst.

Note: Due to specic country requirements,

the PVR function is not available for Finland.

1. Press OPTION on the remote control and select QUICK ACCESS > PVR.

2. Press OK/ to enter.

Shortcut operation: Press REC on the remote control to enter the PVR menu directly.

3. Press:

─ the REC button to start recording, the

record le is put into a PVR folder in

MEDIA > VIDEO;

─ the button to stop recording manually;

if the recording duration nishes, the recording will stop automatically.

─ / / / to adjust the recording

duration.

4. When recording, PVR mini pane will

also show on the screen to indicate the

recording progress.

5. To watch the recorded programme, exit PVR mode rst and go to MEDIA > VIDEO. Select the folder PVR, then select the related record le. Press OK to play. (It is the same if you record a digital radio programme).

Notes:

─ When CI+ card is used, PVR function will

be disabled.

─ Only available for digital channels. ─ Only supports USB memory device of

FAT32 format.

─ Before you connect the USB memory

stick to the TV, make sure you have backed up the data in the device to avoid the risk of losing important data due to unforeseen malfunction.

─ The bigger the USB-memory stick

memory size for the PVR function, the longer the recording time.

─ If you want to change channel or signal

source during recording, store the recording data before changing the channel or source.

─ The TV cannot play les normally if

the parameters of the le exceed the limitations of the system, the le format is not supported, the le is damaged, or the le cannot be decoded.

─ Do not disconnect the USB memory stick

when the system is reading a le or

transmitting data, otherwise the system or the device may be damaged.

Schedule List

This function is used to perform scheduled

recording.

1. Press OPTION on the remote control

and select QUICK ACCESS > Schedule List.

2. Press OK to display the Schedule List.

3. To add a schedule into your schedule list, press the red button rst to display

Schedule List. Then,

─ Channel Number: use / to select

the channel number.

─ Start Date: use the digit buttons to set

the recording date.

─ Start Time: set the starting time of the

recording.

─ Stop Time: set the stopping time of the

recording.

─ Schedule Type:

• Set Reminder to be reminded that you

can switch to the scheduled programme

when the time you have set comes. When

time is out and you do not execute any operation, the dialog box will disappear

and no further operation will be executed.

• Set Record to check if you really want

to start your scheduled recording when

the time you have set comes. When

time is out and you do not execute any operation, scheduled recording will start

automatically.

─ Repeat Type: set different repeat

modes for the recording.

4. Press / / / to select Add, then

press OK to add the schedule you set

into your schedule list.

5. Press the red button to repeat above procedures to add another schedule.

6. If you wish to edit or delete a schedule, select it and press OK to enter.

7. Press EXIT to close the menu.

Network connection

You can set up your TV so that it can access

the Internet through your local area network (LAN) using a wired or wireless connection.

Connecting to a wired network

You can attach your TV to your LAN using

cable in three ways:

• You can attach your TV to your LAN by

connecting the LAN port on your TV to an external modem using a Cat 5 cable.

• You can attach your TV to your LAN by connecting the LAN port on your TV to an IP Sharer, which is connected to an external modem. Use Cat 5 cable for the connection.

• Depending on how your network is congured, you may be able to attach your TV to your LAN by connecting the LAN port on your TV directly to a network wall outlet using a Cat 5 cable. Note that

the wall outlet is attached to a modem or

router elsewhere in your house.

Select SETUP > Network > Settings > Interface, then select Ethernet to connect

to a wired network.

Connecting to a wireless network

To connect your TV to your network

wirelessly, you need a wireless router or

modem and a WIFI-adapter, you will have to

buy one separately. Connect WIFI-adapter to your TV’s USB 1 port.

1. Select SETUP > Network > Settings

> Interface, then select Wireless to

connect to a wireless network.

2. Select Wireless Setting and press

OK/ to enter.

3. Connection Methods: You can setup the wireless network connection three ways.

─ Scan

• Select Wireless Setting > Scan, then

press OK/ , the TV will scan all access

points within range. The access points found by the TV will be displayed.

• Select an available access point, then press OK/ to connect the TV.

Notes:

─ If you select a protected access point,

you will have to enter the corresponding password. Press OK on the remote control to display the virtual keyboard to enable you to enter the password.

─ This TV has a memory function of

available access point, which enables your TV to be connected to the network even if you switch on the TV after power off.

─ Manual

Select Wireless Setting > Manual, then press OK/ , you will be prompted to enter the correct SSID of an available

wireless router to set up the connection.

─ Auto

If your AP supports WPS (Wi-Fi Protected Setup), you can connect to the network via PIN (Personal Identication Number) or PBC (Push Button Conguration). WPS will automatically congure the SSID and WPA key in either mode.

Select Wireless Setting > Auto, then press OK/ to enter.

• PIN: Select PIN and press OK/ to enter. Generate a random PIN code. Make sure this code is installed on the AP. (For the procedures, refer to your router manual.) Press OK/ again to set up the connection.

• PBC: If your router has a PBC push

button, select PBC, then press OK/ to

enter. Press the PBC push button on your

router within 2 minutes after you press

OK/ again. Your TV will automatically

acquire all the network setting values it

needs and connect to your network.

Network setup

1. Press MENU on the remote control and

select SETUP > Network > Settings > Internet Connection. Press / to select On. Wait until the connection is

automatically established.

2. Select SETUP > Network > Settings

> Connection Test, then press OK/

to check the Internet connectivity. If it does not work, follow below steps to make sure of the connectivity.

3. Select SETUP > Network > Settings

> IP Setting, then press OK/ to enter the IP Setting menu.

─ Set Address Type to Auto, it will

acquire and enter the needed IP address automatically.

─ You can follow below steps to enter your

IP address manually.

• Set Address Type to Manual, then press to go to the rst entry eld.

• Enter the IP Address, Subnet Mask,

Default Gateway, Primary DNS and Secondary DNS values. Use the digit

buttons to enter numbers and the arrow

buttons to move from one entry eld to another.

─ After setting, select Setup > Network

> Settings > Connection test to check

the Internet connectivity again.

4. Select SETUP > Network > Settings

> Information, then press OK/ to display the information on current connection, such as Interface, Address

type, IP address, etc.

Browse PC through Share & See

If you have photos, videos or music les

stored on a computer connected through a

home network, you can play your les on your TV.

Connecting to your PC

Make sure to set up a wired or wireless connection from your TV to a router rst. Then connect your PC to your router either through a network cable or wirelessly. Also make sure SETUP > Network >

Settings > Internet Connection is On

and your computer reware won’t block the connection.

Enabling Share & See function

Select SETUP > Network > Applications

> Share & See, and set it to On.

Follow the steps in turn specied hereafter.

Adding media from your PC for sharing

Install a Share & See media server on your

PC. The simple and familiar server you may install is Microsoft Windows Media Player 11. Allow your TV to share the designated les on your PC.

1. Open the Microsoft Windows Media Player 11.

─ Select Library > Media sharing. ─ Check the checkbox Share my media

to.

─ Select the icon of the TV connected to

your PC.

─ Select Allow to allow the TV to access

your PC, and select OK to enable your allowing.

Note: Use the Settings button to customize your desired settings.

─ Select Library > Add to Library. ─ Select your personal folders or folders

of other users that you can access for

sharing.

─ Select Add and press OK to enable your

adding.

Share & See application

Select MEDIA in the main menu and press OK to enter media center. Then you can

view photos, listen to music or watch videos,

which are stored on your PC.

Smart TV

Allows you to enjoy internet applications

(Apps), specially adapted internet websites for your TV. You can control the Apps with the TV remote control.

WARNING:

• Congure the network settings before using Smart TV.

• Slow responses and/or interruptions

may occur, depending on your network conditions.

• If you experience a problem using an application, please contact the content

provider.

• According to circumstances of the contents provider, an application's updates or the application itself may be

discontinued.

• Depending on your country's regulations,

some applications may have limited

service or not be supported.

Access Smart TV Applications (Apps)

1. Select SMART TV in the main menu and

press OK to display the smart TV home

page.

Shortcut operation: Press SMART TV on the remote control to display the smart TV

home page directly.

1. Use / / / to select an App and press OK to enter.

HbbT V

Some broadcasters of digital channels offer interactive HbbTV (Hybrid Broadcast

Broadband TV). With HbbTV, broadcasters combine their normal TV programme with all kinds of information or entertainment. You can browse this information interactively.

To fully enjoy HbbTV, you need to connect

your TV to the internet.

Note: You cannot download les to your TV

with this feature.

Access HbbTV

When you tune to a TV channel that offers

HbbTV, press the red button to open the interactive pages. Then use / / / to navigate the HbbTV pages and press OK to

conrm.

Contact IKEA

If you have any questions regarding your

new UPPLEVA TV or Sound System or need

service or support, contact IKEA Customer

Service at www.IKEA.com.

To be sure we can give you the best possible assistance, please read the manual carefully

before contacting us. And have the article

number for your purchase at hand when you

call. You’ll nd this 8-digit article number on your receipt or on the back of your UPPLEVA TV or Sound System.

Notes for password in Parental Control Lock function:

─ The default password is 1234. You can

change it to a new one.

─ The super password is 0423. If you

forget your code, enter the super password to override any existing codes.

Screen resolution:

─ 1920X1080

DANSK

Vigtige oplysninger Sikkerhed

Sørg for at kontrollere, at spændingen på

lysnettet stemmer overens med den

spænding, som er angivet på identikationspladen bag på tv'et. Når netstikket eller en apparatkontakt bruges som afbryderenhed, skal denne enhed altid være funktionsdygtig.

På nogle modeller sidder lysindikatoren på siden af tv'et. Manglende lysindikation foran betyder ikke, at tv'et er frakoblet lysnettet helt. For at frakoble tv'et helt skal netstikket trækkes ud.

Tv-komponenterne er følsomme over for varme. Den maksimale omgivende temperatur må ikke overstige 35º. Ventilationsåbningerne bag på og på siderne af tv'et må ikke tildækkes. Sørg for, at der er plads nok omkring tv'et til at sikre tilstrækkelig ventilation. Installer ikke tv'et i nærheden af varmekilder (brændeovn osv.) eller apparater, der skaber kraftige magnetiske eller elektriske felter.

Fugtigheden i det rum, hvor tv'et installeres, må ikke overstige en luftfugtighed på 85%.

Apparatet må ikke udsættes for dryp

eller stænk, og genstande fyldt med væske, må ikke placeres på apparatet. Hvis

tv'et yttes fra et koldt til et varmt sted, kan der dannes kondens på skærmen (og på nogle komponenter inde i tv'et). Lad kondensen fordampe, før du tænder for tv'et igen.

ADVARSEL!

For at undgå, at ild spreder sig, skal stearinlys og åben ild altid holdes væk fra tv'et.

bølger, som kan beskadige det. Der skal derfor være nem adgang til lysnet- og antennestik, så de kan afbrydes, hvis det er nødvendigt.

Tag straks stikket til tv'et ud, hvis du

bemærker, at det lugter brændt eller afgiver røg. Du må aldrig under nogen

omstændigheder selv åbne for tv'et, da du risikerer at få elektrisk stød.

Tv-skærm

Tv-skærmen på dette produkt er fremstillet af glas og kan derfor gå i stykker, hvis du

taber det, eller det bliver udsat for stød fra

andre genstande.

Tv-skærmen er et højteknologisk produkt, som giver dig billeder med ne detaljer. Af og til kan nogle få ikke-aktive pixels optræde på skærmen som et fast blåt, grønt eller rødt punkt. Det påvirker ikke produktets ydeevne.

Pleje

Brug et glasrengøringsmiddel til rengøring

af skærmen samt en blød klud og et mildt

rengøringsmiddel til rengøring af resten af

tv'et.

Vigtigt! Brug af stærke opløsningsmidler, slibemidler eller alkoholbaserede produkter kan beskadige skærmen.

Støv jævnligt ventilationsåbningerne af bagpå og på siderne. Brug af opløsningsmidler, slibemidler eller alkoholbaserede produkter kan beskadige tv'et. Hvis en genstand eller væske trænger ind i tv'et, så tag straks stikket ud, og få en autoriseret tekniker til at undersøge det. Åbn aldrig selv tv'et, da du udsætter dig for fare og kan risikere at beskadige det.

Knappen , knappen eller knappen på fjernbetjeningen kan bruges til at tænde og sætte tv'et på standby.

længere tid

stikket ud af stikkontakten.

Det tilrådes at koble tv'et og antennen fra lysnettet under tordenvejr, så det ikke påvirkes af elektriske eller magnetiske

Hvis du ikke skal se tv i

, så sluk det helt ved at tage

POWER

/ på tv'et

+ 60 hidden pages