Page 1
LAGAN
HGA4K
GB
GB
Page 2
Page 3
GB
ENGLISH 4
Language
Country
Page 4
Contents
Safety information 4
Product description 5
Daily use 5
Helpful hints and tips 6
Care and cleaning 7
What to do if… 7
Technical data 8
Installation 9
Environment concerns 11
IKEA GUARANTEE 12
Subject to change without notice
Safety information
For your safety and correct operation of
the appliance, read this manual carefully
before installation and use. Always keep these
instructions with the appliance even if you
move or sell it. Users must fully know the operation and safety features of the appliance.
Correct use
• Do not leave the appliance unattended dur-
ing operation.
• The appliance is designed exclusively for
domestic use.
• The appliance must not be used as a work
surface or as a storage surface.
• Do not place or store flammable liquids,
highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium) in
or near the appliance.
• Watch out when connecting electric appli-
ances to sockets nearby. Do not allow connecting leads to come into contact with or to
catch underneath the appliance or hot cookware.
• Do not do repairs yourself to prevent injury
and damage to the appliance. Always contact your local After Sales Service (refer to
the Service chapter).
Child safety
• Only adults can use this appliance. Children
must get supervision to make sure that they
do not play with the appliance.
• Keep all packaging away from children.
There is a risk of suffocation.
• Keep children away from the appliance
when it is on.
General safety
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Ensure there is a continuous air supply while
using the hob, keep air vents in good condition or install a cooker hood with a venting
hose. Improve ventilation by opening a window or increasing the extractor speed.
• This appliance is supplied with safety device
in form of the thermocouple. If after ignition
of the burner or during use flame will go out
and the thermocouple will not be heat up
enough gas supply will be interrupted.
Installation
• Make sure that the appliance is not damaged because of transport. Do not connect
a damaged appliance. If necessary, contact
the After Sales Service (refer to the Service
chapter).
• Only an authorized service engineer can install, connect or repair this appliance. Use
only original spare parts.
• Built-in appliances can only be used after
they are built into suitable built-in units and
work surfaces that meet standards.
• Do not change the specifications or modify
this product. Risk of injury and damage to
the appliance.
Warning! Carefully obey the instructions
for electrical and gas connections.
ENGLISH 4
Page 5
• Do not install the appliance if it is damaged
during the transportation.
Safety during use
• Remove all packaging, stickers and film from
the appliance before the first use.
Warning! Fire hazard! Overheated fats
and oils can ignite very quickly.
• Switch the burners off after each use.
• Risk of burns! Burners and accessible parts
become hot during use. Make sure pots do
not protrude over the edges of the cooktop.
How to avoid damage to the appliance
• To avoid damaging the hob, do not allow
saucepans or frying pans to boil dry.
• Do not use the burners with empty cookware
or without cookware.
• Never line any part of the appliance with
aluminium foil. Never place plastic or any
other material which may melt on the appliance.
Product description
8
9
1
2
7
6
5
4
3
10
1 Auxiliary burner
2 Rapid burner
3 Semi Rapid burner
4 Semi Rapid burner
5 Semi Rapid burner control knob
6 Semi Rapid burner control knob
7 Rapid burner control knob
8 Auxiliary burner control knob
9 Ignition button
10 Removable pan supports
Burner control knob
The burner control knobs are situated on the
right side of the hob.
Symbol Description
there is no gas supply / off position
there is maximum
gas supply
there is minimum gas
supply
Daily use
Ignition of the burner
Always ignite the burner before positioning pots or pans
To ignite the burner:
1. Push the electric ignition button witch is
marked by a little spark
, at the same
time turn the relevant control knob anticlockwise to maximum position
.
ENGLISH 5
Page 6
2. Keep the knob pushed for about 5 sec; this
will allow thermocouple to heat up, and the
safety device to switch off, otherwise the
gas supply would be interrupted.
3. After the flame is regular, adjust it as preferred.
If after a few attempts the burner does not
ignite, check that the crown and its cap
are in correct positions.
1
2
3
4
5
1 Burner cap
2 Burner crown
3 Ignition candle
4 Injector
5 Thermocouple
Warning! Do not keep control knob
pressed for more than 15 seconds.
If the burner does not light after 15 seconds,
release the control knob, turn it into off position
and wait for at least 1 minute before trying to
light the burner again.
Important! In the absence of electricity You
can ignite the burner without electrical device;
in this case approach the burner with a flame,
push the relevant knob down and turn it
counter-clockwise to maximum gas release
position.
Warning! Maintain extreme caution
when using open fire in kitchen
environment. Manufacturer decline any
responsibility in case misuse of the flame.
If the burner accidentally goes out, turn
the control knob to the off position and
wait for at least 1 minute before trying to light
it again.
When switching on the mains, after in-
stallation or a power cut, it is quite normal
for the spark generator to be activated automatically.
Turning the burner off
To put the flame out, turn the knob to the symbol
.
Warning! Always turn the flame down or
switch it off before removing the pans of
the burner.
Helpful hints and tips
Energy savings
• If possible, always place lids on the pans.
• As soon as liquid starts boiling, turn down
the flame to barley keep the liquid simmering.
Use pots and pans with bottom fitting the size
of burner used.
Burner minimum diam-
eter of pots and
pans
maximum di-
ameter pots
and pans
Rapid 180 mm 260 mm
Semirapid
120 mm 220 mm
Auxili-
ary
80 mm 160 mm
ENGLISH 6
Page 7
The bottom of the cookware should be as thick
and flat as possible.
Care and cleaning
Warning! Switch the appliance off and
let it cool down before you clean it.
Warning! For safety reasons, do not
clean the appliance with steam blasters
or high-pressure cleaners.
Warning! Do not use abrasive cleaners,
steel wool pads or acids, they will
damage the appliance.
To remove any food remains wash the enamelled elements, "caps" and "crowns", with
warm soapy water.
Stainless steel elements wash with water, and
then dry with a soft cloth.
This model is equipped with electrical ignition,
it is obtained through ceramic "candle" and
electrode.
Keep them well clean to avoid difficult lightning.
Periodically ask your local Service Centre
to check the conditions of the gas supply
pipe and the pressure adjuster, if it is fitted (this
service is not free of charge).
After cleaning, be sure to wipe dry with a soft
cloth.
What to do if…
Problem Possible cause Remedy
There is no spark when lighting the gas
There is no electrical supply Check that the unit is plugged
in and the electrical supply is
switched on.
Check the house electric in-
stallation fuse.
Burner cap and Crown are
placed uneven
Check the burner cap and
crown have been replaced
correctly, e.g. after cleaning.
The flame is blowing out immediately after lightning
Thermocouple is not heated
enough
After lightning the flame, keep
the knob pushed for about 5
sec.
The gas ring burns unevenly Burner crown is blocked with
food residues
Check the main injector is not
blocked and the burner crown
is clear of food particles.
If there is a fault, first try to find a solution to
the problem yourself. If you cannot find a solution to the problem yourself, contact your
dealer or the After Sales Service.
If you operated the appliance wrongly, or
the installation was not carried out by a
registered engineer, the visit from the customer
service technician or dealer may not take
place free of charge, even during the warranty
period.
ENGLISH 7
Page 8
Technical data
Hob dimensions
width 580 mm
depth 500 mm
built in height 12 mm
Class Appliance: 3
Appliance Category: II2H3+
Appliance gas supply: Natural gas G20 (2H)
20 mbar
This appliance is designed for use with natural
gas but can be converted for use with other
gas type according to table below.
Type of Gas
Burner
type
Injectors
1/100
mm
Nominal
Power
kW
Nominal Flow g/h
Reduced
Power
kW
by-pass
1/100
mm
G30
28/30
mbar
G31 37
mbar
G20 20
mbar
Rapid
(large)
119 3.0 - - 0.75 42
Semi-
rapid
(medi-
um)
96 2.0 - - 0.45 32
Auxili-
ary
(small)
70 1.0 - - 0.33 28
G30/G31
28-30/37
mbar
Rapid
(large)
86 2.8 204 200 0.75 42
Semi-
rapid
(medi-
um)
71 2.0 145 143 0.45 32
Auxili-
ary
(small)
50 1.0 73 71 0.33 28
Rating Plate
301-560-09
Made In Italy
© Inter IKEA Systems B.V. 1999
21552
PQM
PNC. 949620663 TYPE H6ML40-4/VA/060ce
G20 20 mbar = 8 kW
G31 37mbar = 557 g/h
G30 28-30 mbar = 567 g/h
II2H6+ (GB)
230 V
~
50 Hz
ZO 0051
ENGLISH 8
Page 9
The graphic above represents rating plate of
the appliance (without serial number which is
generated dynamically during the production
process), which is located at its underneath
surface of the casing.
Dear Customer, please apply here aside the
sticker you can find in the dedicate plastic bag
inserted inside the hob packaging. This will allow us to assist you better, by identifying precisely your hob, in case you will need in future
our assistance. Thank you for your help!
Installation
Manufacturer is not responsible for any injury
to persons and pets or damage to property
caused by failure to comply following requirements.
Caution! To proceed with the installation
refer to the assembly instructions.
Warning! Installation process must follow
the laws, ordinances, directives and
standards (electrical safety rules and
regulations, proper recycling in accordance
with the regulations, etc.) in force in the country
of use!
Ensure that the local distribution condi-
tions (nature of the gas and gas pressure)
and the adjustment of the appliance are compatible before proceeding with the installation.
The parameters of adjustment setting for
this appliance are stated on the rating
plate (refer to the Technical data chapter).
Warning! The appliance must be
earthed!
Warning! Risk of injury from electrical
current.
• The electrical mains terminal is live.
• Make electrical mains terminal free of volt-
age.
• Loose and inappropriate plug and socket
connections can make the terminal overheat.
• Have the clamping connections correctly installed.
• Use strain relief clamp on cable.
Important! You must observe the minimum
distances to other appliances and furniture
cabinets or other units according to Assembly
Instruction.
If there is no oven beneath the hob insert a dividing panel at a minimum distance of 20 mm
from the bottom of the hob.
Protect the cut surfaces of the worktop against
moisture using a suitable sealant included in
the product in fitting bag. The sealant seals the
appliance to the work top with no gap. Do not
use silicon sealant between the appliance and
the worktop. Avoid installing the appliance
next to doors and under windows as hot cookware may be knocked off the pan support
when doors and windows are opened.
Only an authorized service engineer can install, connect or repair this appliance. Any gas
installation must be carried out by a GAS SAFE
REGISTER installer. Use only original spare
parts.
Gas Connection
Warning! This appliance is not
connected to a combustion products
evacuation device.
Installation must comply with current local regulation.
ENGLISH 9
Page 10
The connection of the cooktop to the gas pipe
network or gas cylinder must be made by
means of a rigid copper or steel pipe with fittings complying with local regulations, or by
means of a continuous surface stainless steel
hose complying with local regulations.
If you see any abnormalities do not repair
the pipe, contact local After Sales Service
(refer to the Service chapter).
The connection must be installed correctly,
fixed into hob connection pipe. Otherwise it
will cause leakage of gas
Warning! Once the installation is
complete, check the perfect seal of every
pipe fixing. Use soapy water, never flame.
Electrical connection
Before connecting, check that the nominal voltage of the appliance stated on the rating
plate, corresponds to the available supply
voltage. Also, check the power rating of the
appliance and ensure that the wire is suitably
sized to suit the appliance power rating (refer
to the Technical data chapter).
The rating plate is located on the lower casing
of the hob.
The appliance is supplied with a connection
cable. This has to be provided with a proper
plug, able to support the load marked on the
identification plate. To connect the plug to the
cable, follow the recommendation given in following figure.
1
2
Replacement of the connection cable
The replacement of the connection cable requires the specific equipment of a technician.
In this case, only cable type H05V2V2-F T90
must be used. The cable section must be suitable to the voltage and the working temper-
ature. The yellow/green earth wire
2
must be
approximately 2 cm longer than the brown (or
black) phase wire
1
(previous figure).
The plug has to be fitted in a proper socket. If
connecting the appliance directly to the electric system, it is necessary that you install a
double pole switch between the appliance
and the electricity supply, with a minimum gap
of 3 mm between the switch contacts. The double pole has to be of a type suitable for the
required load in compliance with the current
rules.
The connection cable has to be placed in order
that, in each part, it cannot reach a 90 °C temperature. The blue neutral cable must be connected to the terminal block marked with "N".
The brown (or black) phase cable (fitted in the
terminal block contact marked with "L") must
always be connected to the live phase.
ENGLISH 10
Page 11
Gas setting conversion
This model is designed for use with natu-
ral gas but can be converted for use with
butane or propane gas providing the correct
injectors. The injectors not supplied with the
appliance have to be ordered from After Sales
Service (refer to the Service chapter).
For data concerning injector replacement, see
chapter "Technical data"
Warning! Conversion or replacement
can only be performed by a registered
installer.
To replace injectors:
1. Remove pan support.
2. Remove burner cap and crown.
3. With a socket spanner 7 unscrew and re-
move the injectors, replace them with the
ones required for the type of gas in use.
4. Reassemble the parts, following the same
procedure backwards.
Important! Replace the rating label (placed
near gas supply pipe) with relevant one for the
new type of gas supply before sealing the
appliance. If the appliance is already sealed
please stick it directly on the user manual
booklet after Technical data chapter close to
the rating plate drawing.
You can find this label in package sup-
plied with appliance
If the feeding gas pressure will be differ-
ent or variable, comparing with the required, you must install an appropriate pressure adjuster, which is not supplied with the
product and if needed must be ordered separately from the local After Sales Service (refer
to the Service chapter). The pressure adjuster
must be fitted on gas supply pipe, in compliance with the rules of the force.
The rating plate is located on the lower casing
of the hob.
Adjusting flame level
When hob has been fully installed, it is necessary to check the minimum flame setting:
1. Turn the gas tap to the maximum position
and ignite.
2. Set the gas tap to the minimum flame position then turn the control knob from minimum to maximum several times. If the flame
is unstable or extinguished, follow the procedure further.
3. Re-ignite the burner and set to minimum.
4. Remove the control knob.
5. To adjust, use a thin bladed screwdriver
and turn the adjustment screw until the
flame is steady and does not extinguish,
when the knob is turned from minimum to
maximum, and vice versa (see following
picture).
6. Repeat this procedure for all burners.
7. Reassemble the knobs.
Warning! If the appliance is connected
to liquid gas (G31 propane or G30
butane), the regulation screw must be fastened
as tightly as possible.
IKEA of Sweden AB
SE-34381 Älmhult
Environment concerns
The symbol on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
ENGLISH 11
Page 12
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
Packaging materials
The materials with the symbol
are recyclable. Dispose the packaging in a suitable collection containers to recycle it.
Before disposal of appliance
Warning! Do these steps to dispose the
appliance:
• Pull the mains plug out of the mains socket.
• Cut off the mains cable and discard it.
IKEA GUARANTEE
How long is the IKEA guarantee valid?
This guarantee is valid for five (5) years from
the original date of purchase of Your appliance at IKEA, unless the appliance is named
LAGAN in which case two (2) years of guarantee apply. The original sales receipt is required as proof of purchase. If service work is
carried out under guarantee, this will not extend the guarantee period for the appliance,
Which appliances are not covered by the
IKEA five (5) years guarantee?
The range of appliances named LAGAN and
all appliances purchased in IKEA before 1st of
August 2007
Who will execute the service?
IKEA service provider will provide the service
through its own service operations or authorized service partner network.
What does this guarantee cover?
The guarantee covers faults of the appliance,
which have been caused by faulty construction
or material faults from the date of purchase
from IKEA. This guarantee applies to domestic
use only. The exceptions are specified under
the headline “What is not covered under this
guarantee?” Within the guarantee period, the
costs to remedy the fault e.g. repairs, parts, labour and travel will be covered, provided that
the appliance is accessible for repair without
special expenditure. On these conditions the
EU guidelines (Nr. 99/44/EG) and the respective local regulations are applicable. Replaced
parts become the property of IKEA.
What will IKEA do to correct the problem?
IKEA appointed service provider will examine
the product and decide, at its sole discretion,
if it is covered under this guarantee. If considered covered, IKEA service provider or its authorized service partner through its own service operations, will then, at its sole discretion,
either repair the defective product or replace
it with the same or a comparable product.
What is not covered under this guarantee?
• Normal wear and tear.
• Deliberate or negligent damage, damage
caused by failure to observe operating instructions, incorrect installation or by connection to the wrong voltage, damage
caused by chemical or electro-chemical reaction, rust, corrosion or water damage including but not limited to damage caused by
excessive lime in the water supply, damage
caused by abnormal environmental conditions.
• Consumable parts including batteries and
lamps.
• Non-functional and decorative parts which
do not affect normal use of the appliance,
including any scratches and possible color
differences.
• Accidental damage caused by foreign objects or substances and cleaning or unblocking of filters, drainage systems or soap
drawers.
ENGLISH 12
Page 13
• Damage to the following parts: ceramic
glass, accessories, crockery and cutlery baskets, feed and drainage pipes, seals, lamps
and lamp covers, screens, knobs, casings
and parts of casings. Unless such damages
can be proved to have been caused by production faults.
• Cases where no fault could be found during
a technician’s visit.
• Repairs not carried out by our appointed
service providers and/or an authorized
service contractual partner or where nonoriginal parts have been used.
• Repairs caused by installation which is faulty
or not according to specification.
• The use of the appliance in a non-domestic
environment i.e. professional use.
• Transportation damages. If a customer
transports the product to their home or other
address, IKEA is not liable for any damage
that may occur during transport. However,
if IKEA delivers the product to the customer's
delivery address, then damage to the product that occurs during this delivery will be
covered by this guarantee.
• Cost for carrying out the initial installation of
the IKEA appliance. However, if an IKEA
service provider or its authorized service
partner repairs or replaces the appliance
under the terms of this guarantee, the service provider or its authorized service partner
will re-install the repaired appliance or install the replacement, if necessary.
This restriction do not apply to fault-free work
carried out by a qualified specialist using our
original parts in order to adapt the appliance
to the technical safety specifications of another
EU country.
How country law applies
The IKEA guarantee gives You specific legal
rights, which covers or exceed local demands.
However these conditions do not limit in any
way consumer rights described in the local
legislation
Area of validity
For appliances which are purchased in one EU
country and taken to another EU country, the
services will be provided in the framework of
the guarantee conditions normal in the new
country. An obligation to carry out services in
the framework of the guarantee exists only if
the appliance complies and is installed in accordance with:
• the technical specifications of the country in
which the guarantee claim is made;
• the Assembly Instructions and User Manual
Safety Information;
The dedicated After Sales Service for IKEA
appliances:
Please do not hesitate to contact IKEA After
Sales Service to:
1. make a service request under this guaran-
tee;
2. ask for clarification on installation of the
IKEA appliance in the dedicated IKEA
kitchen furniture. The service won’t provide
clarifications related to:
– the overall IKEA kitchen installation;
– connections to electricity (if machine
comes without plug and cable), to water
and to gas since they have to be executed by an authorized service engineer.
3. ask for clarification on user manual con-
tents and specifications of the IKEA appli-
ance.
To ensure that we provide you with the best
assistance, please read carefully the Assembly
Instructions and/or the User Manual section of
this booklet before contacting us.
How to reach us if You need our service
Please refer to the last page of this manual for
the full list of IKEA appointed contacts and relative national phone numbers.
ENGLISH 13
Page 14
Important! In order to provide You with a
quicker service, we recommend that You use
the specific phone numbers listed at the end of
this manual. Always refer to the numbers listed
in the booklet of the specific appliance You
need an assistance for. Before calling us,
assure that You have to hand the IKEA article
number (8 digit code) for the appliance of
which you need our assistance.
Important! SAVE THE SALES RECEIPT! It is
Your proof of purchase and required for the
guarantee to apply. Note that the receipt
reports also the IKEA article name and number
(8 digit code) for each of the appliances you
have purchased.
Do You need extra help?
For any additional questions not related to After Sales of your appliances, please contact
our nearest IKEA store call centre. We recommend you read the appliance documentation
carefully before contacting us.
ENGLISH 14
Page 15
Country Phone number Call Fee Opening time
België
070 246016
Binnenlandse gesprekskosten 8 tot 20 Weekdagen
Belgique Tarif des appels nationaux 8 à 20. En semaine
България 0700 10 218 Такса за повикване от страната От 9 до 18 ч в работни дни
Česká republika 246 019721 Cena za místní hovor 8 až 20 v pracovních dnech
Danmark 70 15 09 09 Landstakst
man.-fre. 09.00-20.00
lør. 09.00-16.00
1 søndag pr. måned, normalt første
søndag i måneden
Deutschland 01803-334532
(0,09 € / Min.*) * aus dem Festnetz
der DTAG; Mobilfunkpreise
abweichend
8 bis 20 Werktage
Ελλάδα 211 176 8276 Υπεραστική κλήση 8 έως 20 κατά τις εργάσιμες ημέρες
España 91 1875537 Tarifa de llamadas nacionales De 8 a 20 en días laborables
France 0170 36 02 05 Tarif des appels nationaux 9 à 21. En semaine
Ireland 0 14845915 National call rate 8 till 20 Weekdays
Ísland 5880503 Innanlandsgjald fyrir síma 9 til 18. Virka daga
Italia 02 00620818
Tariffa applicata alle chiamate
nazionali
dalle 8 alle 20 nei giorni feriali
Κυπρος 22 030 529 Υπεραστική κλήση 8 έως 20 κατά τις εργάσιμες ημέρες
Magyarország 061 998 0549 Belföldi díjszabás Hétköznap 8 és 10 óra között
Nederland
0900 235 45 32
and/or
0900 BEL IKEA
"0,10 EUR/min (niet lokaal)
Incl. BTW"
ma-vr 9.00-21.00
zat 9.00-20.00
zon 9.00-18.00
Norge 815 22052 Takst innland 8 til 20 ukedager
Österreich 0810 300486 zum Ortstarif 8 bis 20 Werktage
Polska 012 297 8787 Stawka wg taryfy krajowej Od 8 do 20 w dni robocze
Portugal 211557985 Chamada Nacional
9 às 21. Dias de Semana
*excepto feriados
România 0212121224 Tarif apel naţional 8 - 20 în zilele lucrătoare
Россия 8 495 6662929
Действующие телефонные
тарифы
с 8 до 20 по рабочим дням
Время московское
Schweiz
031 5500 324
Tarif für Anrufe im Bundesgebiet 8 bis 20 Werktage
Suisse Tarif des appels nationaux 8 à 20. En semaine
Svizzera
Tariffa applicata alle chiamate
nazionali
dalle 8 alle 20 nei giorni feriali
Slovensko (02) 3300 2554 Cena vnútroštátneho hovoru 8 až 20 v pracovných dňoch
Suomi 0207 85 1000 Kotimaan puhelun hinta arkipäivisin 8.00-20.00
Sverige 0775 700 500 lokalsamtal (lokal taxa)
mån-fre 8.30-20.00
lör-sön 9.30-18.00
Türkiye 212 244 0769 Ulusal arama ücreti Hafta içi saat 09:00'dan 18:00'a kadar
Україна 044 586 2078 Міжміськи дзвінки платні 9 - 21 В робочі дні
United Kingdom 020 3347 0044 National call rate 9 till 21. Weekdays
15
Page 16
© Inter IKEA Systems B.V. 2008 AA-401627-1
397109501-B-092009
Loading...