Ikan HF70 Quick Start Guide

www.ikancorp.com | 1.713.272.8822 | [e-mail]

HF70

Helia 70 Watt 4 in. Fresnel Daylight LED Studio Light w/ DMX

Quick Start Guide

What’s Included

1x Helia 70 Watt Fresnel

1x Barn Doors

1x Gel Frame

1x Yoke

1x AC Power Cord

www.ikancorp.com | 1.713.272.8822 | [e-mail]

Getting Started

Thank you for buying the HF150 Fresnel Light from ikan. Please carefully read the instructions and guide before operating the products. The guide includes
product usage and maintenance. When you operate the product, please make sure that you have read the instructions carefully.

All the content of the manual is based on up-to-date information; technical data subject to change without notice.

Safety Instructions

1. Connect the AC power cable to the HF70 light before plugging into the power source. You risk electrocution by not following this instruction.

2. Don’t drag cables with excessive force. Any repairs on the products should be performed by ikan technicians. Users should not remove the power
supply, or else the damage will not be covered under warranty.

3. Be sure that the power is off before connecting and changing the fixture head or disconnecting your cable from the power source. We recommend using
Ikan connecting cables and connectors to avoid electrical shock.

4. The voltage shouldn’t exceed the value in the technical specifications. If the voltage is greater than, or less than the regulated values, it could damage
the product.

Overview

Color temperatures of 5600K (daylight). Ikan developed the HF70 Fresnel Light to handle both these temperatures. The HF70 offers a professional and
customizable LED light source. In addition, the light features separately-cooling ducts for optimizing heat dissipation. Specifically, the HF70 Fresnel Light
offers the following features:

1. The 10-100% brightness incremental adjustment of the 5600K temperature

2. A four-inch diameter Fresnel lens provides even, well-distributed light

3. Ultra-low noise and active cooling technology contribute to excellent thermal stability.

4. The power supply will automatically cut off when the fixture overheats.

5. The bright LCD readout is easy to view, enabling smooth adjustment of functions.

6. Digitally adjustable knob allows you to adjust menu settings quickly and accurately.

7. DMX Channel assignments can be adjusted as needed.

8. AC/DC power supply, AC110VAC-270VAC

Instructions

LED Fresnel housing is made aluminum alloy, which is heavy-duty, lightweight, and easy to transport.
The HF70structure is illustrated on the following page.

www.ikancorp.com | 1.713.272.8822 | [e-mail]

Appearance & Structure - Front

SY

N

C

SET

mode

DC42V

D

M

X

512

SPOT

O

F

F

/O

N

5/8 Receiver: Connecting the lamp with stands or grid mounts
Yoke: Adjustable lighting direction

The pushing claw of barn doors; the holding claw of barn doors:

Pushing Claw

Barn Doors

Yoke

Appearance & Structure - Back

Power switch: Turn on/turn off power
Brightness Knob: Adjusts brightness from 10%-100%

(Press in to Toggle off the LED)

LCD Setting Screen: Displays brightness and color temperature

Color/ Brightness

LCD Setting Screen

+ & - Buttons

Knob

Holding Claw

5/8 Receiver

+&- Buttons: Adjusts the DMX channels
SYNC/DC24V: Possibe future update usuage
Fuse Cap: Fuse Holder with T6.3A 250V fuse
AC 110-220V Power Connector: Connecting with 110-220V power cable
Focusing Knob: Changing the Beam angle of the light from flood to spot

Power Switch

SYNC

DC24V

DMX IN/OUT

Fuse Cap

AC 110-220C

Power Connector

Focusing

Knob

www.ikancorp.com | 1.713.272.8822 | [e-mail]

Installation & Power Supply

N

C

SET

mode

D

M

X

512

SPOT

O

F

F

/O

1. Ensure power is off before installation.

2. Place the light on the Ikan customized stands, release the tension knob on the 5/8” receiver, adjust the light in the desired direction, and then tighten
the tension knob on the 5/8” receiver.

3. When connecting the power cords, plug the AC power cords into the AC120 socket on the rear panel (as shown in the drawing).

DMX 512 Controls

The DMX IN/OUT on the HF70 allows for remote fixture control over the brightness.
The 8Bit DMX allows for use with controllers that use just dimmer controls.
Depending on channel assigned the brightness is controlled on the first fader.

What’s in the box?

Please carry and place the packing box carefully. Check the lighting equipment and accessories upon opening the box. Please contact us if anything is
damaged or missing. Please save the packing materials for replacing and repairing the products in the future.

Notice & Maintenance

1. The HF70 Spotlight working temperature range must be regulated. Overheating and Under-cooling will reduce the LED working life.

2. Products must be placed on a stable, dry, flat surface. Avoid exposure to sunlight and operating in an environment with high humidity or explosive gas.

3. Don’t cover the fan vent. It will shorten the working life of the fixture.

4. Don’t beat, knock or shake the lighting equipment during the operation.

5. If the HF70 isn’t working normally, please contact the Ikan repair department. Please don’t disassemble/re-assemble by yourself.

6. Please place the HF70 in a cool and dry place when you don’t use it for an extended period of time.

www.ikancorp.com | 1.713.272.8822 | [e-mail]

Specifications

Beam Angle

Build Material Aluminum

Control Local Knob Control and DMX In/Out

Cooling System Active Cooling Fan

Dimming

Fixture Size

Fixture Weight

Focusing Rotating Rear Knob

Head Type 5600K

Lens 4” Acrylic Fresnel

Light Source 1 x 70 watt LED

Power Supply 6 ft power cable

- 70 degrees

28

Flicker Free Dimming, Onboard
dimming Knob 10%-100% (minimal
color shift)

x 10 x 6 in.

11

lbs

6.3

Rating AC volts 120volts AC,

50-60Hrz, 40 watts

Yoke: Cast Aluminum with 1 1/8” pin

Optional Accessories

Some other products that work well with the Helia HF70 available from Ikan include:

HD-STND-V2
KCP-703
SW-04

Heavy Duty Light Stand
Stage Clamp w/ 16mm Stud
Safety Wire

www.ikancorp.com | 1.713.272.8822 | [e-mail]

Learn More

More dynamic information at official website: www.ikancorp.com

Support

Contact email: [e-mail]

CONDITIONS OF WARRANTY SERVICE

• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.

• The components and maintenance service fee will be charged if the warranty period is expired.

Free Service will not be Provided in the Following Situations:(*Even if the product is still within the warranty period.)

• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.

• Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.

©2018 ikan Corporation. All rights reserved