Page 1
HF150-3PT-KIT
Kit with 3x Helia 4” Fresnel with Hard Case
Quick Start Guide
What’s Included
3 x 4” Fresnel Light
3 x Barn Doors
3 x Gel Frame
3 x Power Cord
3 x Light Stand
1 x Light Stand Bag
1 x Rolling Hard Case
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com because we’re filmmakers too
Page 2
Getting Started
Thank you for buying the HF150 Fresnel Light from ikan. Please carefully read the instructions and guide before operating the products. The guide includes
product usage and maintenance. When you operate the product, please make sure that you have read the instructions carefully.
All the content of the manual is based on up-to-date information; technical data subject to change without notice.
Safety Instructions
1. Connect the AC power cable to the HF150 light before plugging into the power source. You risk electrocution by not following this instruction.
2. Don’t drag cables with excessive force. Any repairs on the products should be performed by ikan technicians. Users should not remove the power
supply, or else the damage will not be covered under warranty.
3. Be sure that the power is off before connecting and changing the fixture head or disconnecting your cable from the power source. We recommend using
Ikan connecting cables and connectors to avoid electrical shock.
4. The voltage shouldn’t exceed the value in the technical specifications. If the voltage is greater than, or less than the regulated values, it could damage
the product.
Overview
Benchmark color temperatures for today’s film and TV production are 5600K (daylight) and 3200K (tungsten). Ikan developed the HF150 Fresnel Light
to handle both these temperatures. With patented technologies, the HF150 offers a professional and customizable LED light source. In addition, the light
features separately-cooling ducts for optimizing heat dissipation. Specifically, the HF150 Fresnel Light offers the following features:
1. The 10-100% brightness incremental adjustment of the 3200K-5600K temperature enable fine-tuning your color range.
2. A four-inch diameter Fresnel lens provides even, well-distributed light
3. Ultra-low noise and active cooling technology contribute to excellent thermal stability.
4. The power supply will automatically cut off when the fixture overheats.
5. The bright LCD readout is easy to view, enabling smooth adjustment of functions.
6. Digitally adjustable knob allows you to adjust menu settings quickly and accurately.
7. DMX Channel assignments can be adjusted as needed.
8. AC/DC power supply, AC110VAC-270VAC
Instructions
LED Fresnel housing is made aluminum alloy, which is heavy-duty, lightweight, and easy to transport.
The HF150 structure is illustrated on the following page.
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com because we’re filmmakers too
Page 3
Appearance & Structure - Front
SY
N
C
SET
mode
DC42V
D
M
X
512
SPOT
O
F
F
/O
N
5/8 Receiver: Connecting the lamp with stands or grid mounts
Yoke: Adjustable lighting direction
The pushing claw of barn doors; the holding claw of barn doors:
Pushing Claw
Barn Doors
Yoke
Appearance & Structure - Back
Power switch: Turn on/turn off power
Color Knob: Adjust the color from 3200K-5600K
(Press in to set DMX channel)
Brightness Knob: Adjusts brightness from 10%-100%
(Press in to Toggle off the LED)
LCD Setting Screen: Displays brightness and color temperature
Color/ Brightness
LCD Setting Screen
+ & - Buttons
Knob
Holding Claw
5/8 Receiver
+&- Buttons: Adjusts the DMX channels
SYNC: Not in use.
DC24V: Not in use.
Fuse Cap: Fuse Holder with T6.3A 250V fuse
AC 110-220V Power Connector: Connecting with 110-220V power cable
Focusing Knob: Changing the Beam angle of the light from flood to spot
Power Switch
SYNC
DC24V
DMX IN/OUT
Fuse Cap
AC 110-220C
Power Connector
Focusing
Knob
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com because we’re filmmakers too
Page 4
Installation & Power Supply
N
C
SET
mode
D
M
X
512
SPOT
O
F
F
/O
1. Ensure power is off before installation.
2. Place the light on the Ikan customized stands, release the tension knob on the 5/8” receiver, adjust the light in the desired direction, and then tighten
the tension knob on the 5/8” receiver.
3. When connecting the power cords, plug the AC power cords into the AC120 socket on the rear panel (as shown in the drawing).
DMX 512 Controls
The DMX IN/OUT on the HF150 allows for remote fixture control over the color and brightness.
The 8Bit DMX allows for use with controllers that use just dimmer controls.
Depending on channel assigned the brightness is controlled on the first fader.
The next fader controls the color temperature from 3200K at 0% to 5600K at 100%.
What’s in the box?
Please carry and place the packing box carefully. Check the lighting equipment and accessories upon opening the box. Please contact us if anything is
damaged or missing. Please save the packing materials for replacing and repairing the products in the future.
Notice & Maintenance
1. The HF150 Spotlight working temperature range must be regulated. Overheating and Under-cooling will reduce the LED working life.
2. Products must be placed on a stable, dry, flat surface. Avoid exposure to sunlight and operating in an environment with high humidity or explosive gas.
3. Don’t cover the fan vent. It will shorten the working life of the fixture.
4. Don’t beat, knock or shake the lighting equipment during the operation.
5. If the HF150 isn’t working normally, please contact the Ikan repair department. Please don’t disassemble/re-assemble by yourself.
6. Please place the HF150 in a cool and dry place when you don’t use it for an extended period of time.
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com because we’re filmmakers too
Page 5
Specifications
Beam Angle 20 - 70 degrees
Build Material Aluminum
Control Local Knob Control and DMX In/Out
Cooling System Active Cooling Fan
Diagonal 17”
Dimming Flicker Free Dimming, Onboard
dimming Knob 100%-10% (minimal
color shift)
Fixture Size 19 x 6 x 12 in.
Fixture Weight 10 lbs
Focusing Rotating Rear Knob
Head Type 3200K - 5600K
Lens 4” Acrylic Fresnel
Light Source 1 x 150 watt LED Bi-Color
Power Supply 6 ft power cable
Rating AC volts 120volts AC,
50-60Hrz, 40 watts
Shipping Dimensions 20 x 10 x 10 in.
Shipping Dimensions
(Metric)
Shipping Weight 14 lb
Shipping Weight (Metric) 6.35 kg
Yoke: Cast Aluminum with 1 1/8” pin
50.8 x 25.4 x 25.4 cm
Optional Accessories
Some other products that work well with the Helia HF150 available from Ikan include:
HD-STND-V2
KCP-703
SW-04
Heavy Duty Light Stand
Stage Clamp w/ 16mm Stud
Safety Wire
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com because we’re filmmakers too
Page 6
Learn More
More dynamic information at official website: www.ikancorp.com
Support
Contact email: support@ikancorp.com
CONDITIONS OF WARRANTY SERVICE
• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
• The components and maintenance service fee will be charged if the warranty period is expired.
Free Service will not be Provided in the Following Situations:(*Even if the product is still within the warranty period.)
• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
• Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.
©2018 ikan Corporation. All rights reserved
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com because we’re filmmakers too
Loading...