Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes
to read this comprehensive manual carefully
before installing and switching on the monitor.
Please keep this manual in a safe place for
your future reference.
ENGLISH
ENGLISH
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC/EU Directive 2014/30/EU “EMC
Directive”, 2014/35/EU “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU
“RoHS Directive”.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in
residential areas, business and light industrial premises and small-scale enterprises, inside as
well as outside of the buildings. All places of operation are characterised by their connection to
the public low voltage power supply system.
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands
Model No. : PL2483H
ENGLISH
We recommend recycling of used product. Please contact your dealer or iiyama
service center. Recycle information is obtained via the Internet, using the address:
http://www.iiyama.com
You can access the Web page of diff erent countries from there.
We reserve the right to change specifi cations without notice.
All trademarks used in this user manual are the property of their respective owners.
ENGLISH
TABLE OF CONTENTS
FOR YOUR SAFETY ............................................................................1
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the
monitor and contact your dealer or iiyama service center immediately. Further use may be
dangerous and can cause fi re or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fi re or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
any object inside may cause fi re, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fi re or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specifi ed power supply. Use of an incorrect voltage will
cause malfunction and may cause fi re or electric shock.
ENGLISH
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fi re or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
FOR YOUR SAFETY 1
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or
smoky areas as it may cause fi re, electric shock or damage. You should also avoid areas where the
sun shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not
pull the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fi re. To allow adequate air circulation, place the monitor at least 10cm (or 4 inches) from any walls.
ENGLISH
When removing the tilt stand, the ventilation slots on the back side of the monitor can be blocked.
This may overheat the monitor and may cause fire or damage. Make sure to allow enough
ventilation when removing the tilt stand. Operating the monitor on its back, side, upside down or on
a carpet or any other soft material may also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cable is disconnected. If you do not disconnect them, it may cause fi re or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable
itself as this may cause fi re or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may
damage your computer.
CAREFUL! PROTECT YOUR HANDS AND FINGERS
Be careful not to hurt your fi ngers or hands when you change the height or the angle.
Injury can occur if care is not taken to avoid fi nger contact with the displays base when adjusting
the height. (Just for height adjustable model.)
REMARK FOR 24/7 USAGE
This product is not specifi cally designed for 24/7 usage in all environments.
OTHERS
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
2 FOR YOUR SAFETY
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE
When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture position to
the correct position.
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
Due to the nature of the LCD screen, an afterimage of the previous screen may remain
after switching the image, when the same image is displayed for hours. In this case, the
screen can be recovered slowly by changing the image or turning off the Power Switch
for some hours.
CUSTOMER SERVICE
If you have to return your unit for service and the original packaging has been
NOTE
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
CLEANING
If you drop any materials or liquids such as water into the monitor when cleaning,
WARNING
CAUTION
NOTE
unplug the power cable immediately and contact your dealer or iiyama service center.
For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
To protect the LCD panel, do not scratch or rub the screen with a hard object.
Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.
Thinner
Benzine
Abrasive cleaner
Spray-type cleaner
Wax
Acid or Alkaline solvent
ENGLISH
CABINET
LCD
SCREEN
Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
Stains can be removed with a cloth lightly moistened with a mild detergent solvent.
Then wipe the cabinet with a soft dry cloth.
Periodic cleaning with a soft dry cloth is recommended.
Don't use tissue paper etc. because these will damage the LCD screen.
FOR YOUR SAFETY 3
BEFORE YOU OPERATE THE MONITOR
FEATURES
Supports Resolutions up to 1920 × 1080
High Contrast 3000:1 (Typical), Adv. Contrast Function Available / Brightness
250cd/m2 (Typical) / Response Time : 4ms (Gray to Gray)
Blue Light Reducer
Flicker-Free
Digital Character Smoothing
Automatic Set-up
ENGLISH
Stereo Speakers
2 × 2W Stereo Speakers
Plug & Play VESA DDC2B Compliant
Windows
Power Management (VESA DPMS Compliant)
VESA Mounting Standard (100mm×100mm) Compliant
Keyhole for Security Lock
®
7/8.1/10 Compliant
CHECKING THE CONTENTS OF THE PACKAGE
The following accessories are included in your package. Check to see if they are enclosed with
the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional
iiyama offi ce.
Power Cable*
Stand-Base*
Safety Guide
CAUTION
4 BEFORE YOU OPERATE THE MONITOR
1
2
1
The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
*
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used. However, all guarantees and warranties are void for any
problems or damage caused by a power cable not supplied by iiyama.
An approved power cord greater or equal to H05VVF, 3G, 0.75mm
used.
2
Accessory for ProLite X2483HSU.
*
3
Accessory for ProLite XB2483HSU.
*
HDMI Cable
Stand*2
Quick Start Guide
USB Cable
Stand-Base with a screw*3
2
must be
INSTALLATION
WARNING
Before installation, make sure the wall, ceiling or desktop arm is strong enough to
hold the necessary weight of the display and the mount.
< WALL MOUNTING >
WARNING
When you use with the wall mounting, in consideration of thickness of the mounting
stage, tighten the M4 Screw with washer which “L” length is 7mm to fasten the
monitor. Using the screw longer than this may cause electric shock or damage
because it may contact with the electrical parts inside the monitor.
L
Mounting Stage
Screw
ENGLISH
Chassis
BEFORE YOU OPERATE THE MONITOR 5
< ROTATING THE DISPLAY >
ProLite XB2483HSU
●
The monitor is designed to be compatible with both landscape and portrait modes.
Video card for portrait display will be required for rotating the image on the screen.
Available
Not Available
Power Indicator
A
ENGLISH
With Stand:
NOTE
ProLite X2483HSU
●
It is designed to be compatible in landscape mode.
Available
A
Landscape
Power Indicator
Portrait
Adjust the monitor’s height before panel rotation.
Attempting to rotate the panel forcibly without adjusting the stand height may cause
damage to the panel or the stand.
Not Available
A
Landscape
Power Indicator
Portrait
A
A
Power Indicator
A
A
A
Power Indicator
6 BEFORE YOU OPERATE THE MONITOR
FITTING AND REMOVAL OF BASE : ProLite XB2483HSU
Put the monitor on a stable surface. The monitor may cause injury or damage if it
CAUTION
<Installation>
falls or is dropped.
Do not give a strong impact to the monitor. It may cause damage.
Unplug the monitor before removal or installation to avoid an electric shock or a
damage.
Stand-Base
Hook
Stand-Base
ENGLISH
Thumb screw for Stand-Base fi xing
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.
Lay the monitor fl at on a table with front face down.
Install the stand-base as shown on above picture.
Use the ‘thumb screw’ provided to secure the base to the monitor.
<Removal>
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.
Lay the monitor fl at on a table with front face down.
Loosen the ‘thumb screw’ to remove the Stand-Base from the monitor.
BEFORE YOU OPERATE THE MONITOR 7
FITTING AND REMOVAL OF BASE : ProLite X2483HSU
Put the monitor on a stable surface. The monitor may cause injury or damage if it
CAUTION
<Installation>
Put a piece of soft cloth on the table beforehand to
prevent the monitor from being scratched. Lay the
monitor fl at on a table with front face down.
ENGLISH
Hold the monitor and install the Stand to the monitor
until it clicks and is secure.
Hold the monitor and install the Stand-Base to the stand
until it clicks and is secure.
falls or is dropped.
Do not give a strong impact to the monitor. It may cause damage.
Unplug the monitor before removal or installation to avoid an electric shock or a
damage.
Stand
Stand-Base
<Removal>
Put a piece of soft cloth on the table beforehand to
prevent the monitor from being scratched. Lay the
monitor fl at on a table with front face down.
Press and hold the hooks inside, and pull the Stand-
Base.
Press the stopper at the top of the stand and pull it to
remove the stand from the monitor.
Stopper
8 BEFORE YOU OPERATE THE MONITOR
Hook
CONTROLS AND CONNECTORS : ProLite XB2483HSU
<Front>
Power Indicator
Blue: Normal operation
NOTE
Orange: Power Management
Power Switch ( )
Menu / Select Button (ENTER)
Scroll Up / Volume Button ( / )
Scroll Down / ECO Mode Button ( / )
Exit Button (EXIT)
Auto Button (INPUT)
Speakers
USB Downstream Connector()
USB Downstream Connector()
USB Upstream Connector()
VGA Connector (D-SUB)
HDMI Connector (HDMI)
DisplayPort Connector (DP)
Keyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
NOTE
without your permission.
Cable Hole
Headphone Connector (LINE OUT)
Audio Connector (LINE IN)
AC Connector( : Alternating current) ( )
<Back>
ENGLISH
BEFORE YOU OPERATE THE MONITOR 9
CONTROLS AND CONNECTORS : ProLite X2483HSU
ENGLISH
<Front>
Power Indicator
Blue: Normal operation
NOTE
Orange: Power Management
Power Switch ( )
Menu / Select Button (ENTER)
Scroll Up / Volume Button ( / )
Scroll Down / ECO Mode Button ( / )
Exit Button (EXIT)
Auto Button (INPUT)
Speakers
USB Downstream Connector()
USB Downstream Connector()
USB Upstream Connector()
VGA Connector (D-SUB)
HDMI Connector (HDMI)
DisplayPort Connector (DP)
Keyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
NOTE
without your permission.
Headphone Connector (LINE OUT)
Audio Connector (LINE IN)
AC Connector( : Alternating current) ( )
<Back>
10 BEFORE YOU OPERATE THE MONITOR
CONNECTING YOUR MONITOR : ProLite XB2483HSU
AV Equipment etc.
Power Cable (Accessory)
Audio Cable (Not included)
Computer
VGA Cable (Not included)*
USB Cable (Accessory)
HDMI Cable (Accessory)
DisplayPort Cable (Not included)
Mouse
Keyboard
Ensure that both the computer and the monitor are switched off .
Connect the computer to the monitor with the signal cable.
Connect the monitor to the audio equipment with the Audio Cable for computer when using the
audio features.
Connect the Power Cable to the monitor fi rst and then to the power source.
Turn on your monitor and computer.
NOTE
The signal cables used for connecting the computer and monitor may vary with the
type of computer used. An incorrect connection may cause serious damage to both
the monitor and the computer. The cable supplied with the monitor is for a standard
connector. If a special cable is required please contact your local iiyama dealer or
regional iiyama offi ce.
For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama offi ce for a suitable adaptor.
Make sure you tighten the fi nger screws at each end of the signal cable.
The Class I pluggable equipment Type A must be connected to protective earth.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Excessive sound pressure from ear-/headphones can cause hearing damage/hearing loss.
[Example of Connection]
<Back>
ENGLISH
* VGA cable is not supplied with the monitor. If you use low quality VGA cable, it may cause a result
of electro-magnetic interference. Please contact the iiyama Support Centre in your country if you
wish to connect the monitor via the VGA input.
[ Collect Cables ]
Put the cables through the cable hole to bundle
them.
BEFORE YOU OPERATE THE MONITOR 11
CONNECTING YOUR MONITOR : ProLite X2483HSU
AV Equipment etc.
Power Cable (Accessory)
Audio Cable (Not included)
Computer
VGA Cable (Not included)*
USB Cable (Accessory)
HDMI Cable (Accessory)
DisplayPort Cable (Not included)
Mouse
Keyboard
Ensure that both the computer and the monitor are switched off .
Connect the computer to the monitor with the signal cable.
Connect the monitor to the audio equipment with the Audio Cable for computer when using the
audio features.
Connect the Power Cable to the monitor fi rst and then to the power source.
Turn on your monitor and computer.
NOTE
ENGLISH
The signal cables used for connecting the computer and monitor may vary with the
type of computer used. An incorrect connection may cause serious damage to both
the monitor and the computer. The cable supplied with the monitor is for a standard
connector. If a special cable is required please contact your local iiyama dealer or
regional iiyama offi ce.
For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama offi ce for a suitable adaptor.
Make sure you tighten the fi nger screws at each end of the signal cable.
The Class I pluggable equipment Type A must be connected to protective earth.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Excessive sound pressure from ear-/headphones can cause hearing damage/hearing loss.
[Example of Connection]
<Back>
* VGA cable is not supplied with the monitor. If you use low quality VGA cable, it may cause a result
of electro-magnetic interference. Please contact the iiyama Support Centre in your country if you
wish to connect the monitor via the VGA input.
12 BEFORE YOU OPERATE THE MONITOR
COMPUTER SETTING
Signal Timing
Change to the desired signal timing listed on page 32: COMPLIANT TIMING.
ADJUSTING THE VIEWING ANGLE : ProLite X2483HSU
For optimal viewing it is recommended to look at the full face
of the monitor.
Hold the stand so that the monitor does not topple when you
change the monitor’s angle.
You are able to adjust the monitor’s angle up to 22 ° upward,
5 ° downward.
In order to ensure a healthy and relaxed body position
when using the monitor at visual display workstations, it is
recommended that the adjusted tilt angle should not exceed
10 °. Adjust the monitor’s angle to your own preference.
5°22°
ENGLISH
NOTE
Do not touch the LCD screen when you change
the angle. It may cause damage or break the LCD
screen.
Careful attention is required not to pinch your
fi ngers or hands into the moving part of the stand
when you change the angle.
BEFORE YOU OPERATE THE MONITOR 13
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE : ProLite XB2483HSU
For optimal viewing it is recommended to
position yourself directly opposite to the full face
of the monitor, then adjust the monitor’s height
and angle to your own preference.
Hold the panel so that the monitor does not topple
when you change the monitor’s height or angle.
You are able to adjust the monitor's height up
to 130mm, angle up to 45 ° right and left, 22 °
upward and 5 ° downward.
130mm
NOTE
ENGLISH
Do not touch the LCD screen when you
change the height or the angle. It
may cause damage or break the LCD
screen.
Careful attention is required not to pinch
your fingers or hands into the moving
part of the stand when you change the
height or the angle.
Injury can occur if care is not taken to
avoid fi nger contact with the displays
base when adjusting the height.
Monitor
Stand
45°
45°
14 BEFORE YOU OPERATE THE MONITOR
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the
COMPLIANT TIMING shown on page 32. You are also able to adjust the picture by following the button
operation shown below. For more detailed adjustments, see page 23 for SCREEN ADJUSTMENTS.
Press the ENTER Button to start the On Screen Display
feature. There are additional Menu items which can be
switched by using the
/ Buttons.
Select the Menu item which contains the adjustment icon
relating to the adjustment you want to make. Press the
ENTER Button. Then, use the
/ Buttons to highlight the
desired adjustment icon.
Press the ENTER Button again. Use the / Buttons to
make the appropriate adjustment or setting.
Press the EXIT Button to leave the menu, and the settings
you just made would be automatically saved.
For example, to correct for vertical position, select Menu item of Image Adjust and then press
the ENTER Button. Then, select V.Position by using the
/ Buttons. An adjustment page
appears after you press the ENTER Button.
Main Menu
Picture Adjust
Input Select
Audio Adjust
Color Adjust
Image Adjust
Language
Setup
Display Information
Reset
Auto Adjust
H. Position
V. Position
Clock
Phase
Sharpness
Video Mode Adjust
Image Adjust
Full Screen
Main Menu
Picture Adjust
Input Select
Audio Adjust
Color Adjust
Image Adjust
Language
Setup Menu
Display Information
Reset
50
50
50
4
3
ENGLISH
Then, use the
/ Buttons to change the vertical position settings. The vertical position of the
overall display should be changing accordingly while you are doing this.
Image Adjust
V. Position
50
Press the EXIT Button lastly, it ends, all changes are saved in the memory.
NOTE
When button operations are aborted during adjustment, On-Screen Display disappears when the
time set for the OSD Time Out has passed. Also, press the EXIT button to quickly turn off the OnScreen Display.
Any changes are automatically saved in the memory when the On Screen Display
disappears.
Turning off the power should be avoided while using the Menu.
Adjustments for H. / V. Position, Pixel Clock and Phase are saved for each signal timing. Except for
these adjustments, all other adjustments have only one setting which applies to all signal timings.
OPERATING THE MONITOR 15
ADJUSTMENT MENU CONTENTS
Direct
Direct
Direct
Picture Adjust *
3
Adjustment ItemProblem / Option Button to Press
Contrast *
2
Too dull
Too intense
Brightness *
ENGLISH
Overdrive
1,2,4
Too dark
Too bright
Off / +1 / +2
It will improve the gray level response time of the LCD panel.
A higher level results in a faster response time.
Off
Typical Contrast Ratio
Adv. Contrast
On
Increased Contrast Ratio
Off Normal
ECO Mode
Mode1
Brightness of back-light is reduced.
Brightness of back-light is reduced more than 1.Mode2
Brightness of back-light is reduced more than 2.Mode3
Off
Blue Light Reducer
Mode1
Mode2
Mode3
1
Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
*
bright.
2
Contrast and Brightness adjustments are disabled when Adv. Contrast mode is activated.
*
3
Picture Adjust adjustment is disabled when i-Style Color is activated.
*
4
Brightness adjustment is disabled when ECO Mode is activated.
*
Typical
Blue light is reduced.
Blue light is reduced more than Mode1.
Blue light is reduced more than Mode2.
You can skip the Menu items and directly display an option setting screen by using the following
button operations.
ECO Mode : Press the
Blue Light Reducer : Pressing and holding of the EXIT Button for 2-3 seconds when the Menu
Button when the Menu is not displayed.
is not displayed.
16 OPERATING THE MONITOR
Input Select
Direct
Direct
Direct
Direct
Adjustment ItemProblem / Option Button to Press
VGA
HDMI
Input Select
Input source is fi xed, not selected automatically when VGA, HDMI and DisplayPort which
NOTE
are selected.
You can skip the Menu items and directly display an option setting screen by using the following
button operations.
Input Select : Press the INPUT Button when the Menu is not displayed.
DisplayPort
Auto
Select the Analog input.
Select the Digital (HDMI) input.
Select the Digital (DisplayPort) input.
Search for an available input source and select
automatically.
Audio Adjust
ENGLISH
Adjustment ItemProblem / Option Button to Press
Volume
Mute
Mute On and Off are switched as follows by pressing the Button successively.
NOTE
On Off
Digital Audio *
*
Suitable for HDMI/DisplayPort input only.
You can skip the Menu items and directly display an adjustment scale by using the following button
operations.
Volume : Press the Button when the Menu is not displayed.
Too soft
Too loud
Off
On
Return the sound volume to the previous level.
Turn off the sound temporarily.
Select the Line-In input. Line-In
Select the HDMI input. HDMI
Select the DisplayPort input. DisplayPort
OPERATING THE MONITOR 17
Color Adjust
Adjustment ItemProblem / Option Button to Press
Cool *
Normal *
Warm *
User Color *
ENGLISH
i-Style Color *
1
1
1
1
2
Bluish white
Greenish white
Reddish white
Red
Green
Blue
Off
Standard
Game
Cinema
Too weak
Too strong
Return to a state set by color adjustment except
i-Style Color.
For general windows environment and monitor
default setting.
For PC game environment.
For movie and video environment.
SceneryFor displaying outdoor scenery images
Text
For text editing and viewing in a word processing
environment.
*1 Cool, Normal, Warm and User Color adjustments are disabled when i-Style Color or Blue Light
Reducer is activated.
2
*
i-Style Color adjustment is disabled when Blue Light Reducer is activated.
18 OPERATING THE MONITOR
Image Adjust
Direct
Direct
Adjustment ItemProblem / Option Button to Press
Auto Adjust *
H. Position *
V. Position *
2
Clock *
2
Phase *
1,2
2
2
Adjust H. / V. Position, Clock and Phase automatically.
Too left
Too right
Too low
Too high
Too narrow
Too wide
To correct fl ickering text or lines
1 2 3 4 5
You can change the picture quality from 1 to 5
Sharpness
(sharp to soft).
Press the
Button to change the picture quality in
numerical order. Press the
Button to change the
picture quality in reverse numerical order.
Video Mode Adjust
Full Screen
Aspect Ratio
Expansion display
Expansion display of Aspect
*1 For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 23 for
SCREEN ADJUSTMENTS.
2
*
Only Analog input.
ENGLISH
You can skip the Menu items and directly display an option setting screen by using the following
button operations.
Auto Adjust : Pressing and holding of the INPUT Button for 2-3 seconds when the Menu is not
displayed.
OPERATING THE MONITOR 19
Language
ENGLISH
Language
Adjustment ItemProblem / Option Button to Press
English
FrançaisFrench
Deutsch
ItalianoItalian
PolskiPolish
EspañolSpanish
English
German
Nederlands
Ĉesky
Dutch
Czech
Russian
Japanese
Simplifi ed Chinese
Setup
Adjustment ItemProblem / Option Button to Press
OSD Position
OSD Time Out
Opening Logo
Auto Power - Off
NOTE
The Auto Power - Off function is enabled as default setting. Monitor will turn off
automatically after 3 hours without any key operation.
If you prefer to use the monitor over 3 hours continuously, please disable The Auto
Power - Off function.
20 OPERATING THE MONITOR
H.Position
V.Position
You can set the OSD display duration time between
5 and 30 seconds.
Off
On
Off
On
OSD is too left
OSD is too right
OSD is too low
OSD is too high
iiyama Logo does not display when the monitor is
turned on.
iiyama Logo displayed when the monitor is turned on.
Auto Power - Off function is turned Off .
Enable the Auto Power - Off function.
Display Information
Display Information
1920x1080 @60Hz
Displays information regarding the current input signal coming from the graphic card in
your computer.
See your graphic card user guide for more information about changing the
NOTE
resolution and refresh.
Reset
ENGLISH
Adjustment ItemProblem / Option Button to Press
Reset All
Return to Menu.
No
Yes
Factory-preset data is restored.
OPERATING THE MONITOR 21
● Lock Mode
<OSD Menu>
1. The OSD lock will be activated by pressing the front button ENTER for about 10 seconds. If you
try to access the OSD by pressing any of the buttons, message "OSD Locked" will appear on the
screen.
2. The OSD lock will be deactivated by pressing the front button ENTER again for about 10 seconds.
<Power Switch>
1. The power switch lock will be activated by pressing the front button for about 10 seconds.
Locking the power switch means that won't be able to turn off the Monitor while the power switch
is locked. If presses the power switch message "Power Button Locked" will appear on the screen.
2. The power switch lock will be deactivated by pressing the front button
seconds.
ENGLISH
again for about 10
22 OPERATING THE MONITOR
SCREEN ADJUSTMENTS
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
The screen adjustments described in this manual are designed to set image position and minimize
fl icker or blur for the particular computer in use.
The monitor is designed to provide the best performance at resolution of 1920 × 1080, but can not
provide the best at resolutions of less than 1920 × 1080 because the picture is automatically stretched
to fi t the full screen. It is recommended to operate at resolution of 1920 × 1080 in normal use.
Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
It is preferable to adjust the image position and frequency with the monitor controls, rather than
the computer software or utilities.
Perform adjustments after a warm-up period of at least thirty minutes.
Additional adjustments may be required after the Auto Adjust depending on the resolution or
signal timing.
The Auto Adjust may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, Pixel Clock
and Phase. The other way is performing each adjustment manually.
Perform the Auto Adjust fi rst when the monitor is connected to a new computer, or resolution is
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after
performing the Auto Adjust, manual adjustments are required. Both adjustments should be made by
using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama.
com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows
®
OS.
ENGLISH
Display the picture at the optimum resolution.
Enter the Test.bmp (screen adjustment pattern) to wallpaper.
NOTE
Consult the appropriate documentation for doing this.
Set the display position to center in the wallpaper setting dialogue box.
[Adjustment pattern]
Zebra pattern
Color bar
Picture frame
OPERATING THE MONITOR 23
Press the AUTO Button. (Auto Adjust)
Adjust the image manually by following procedure below when the screen has a fl icker or
blur, or the picture does not fi t in the display area after performing the Auto Adjust.
Adjust the V.Position so that the top and bottom of the picture frame will fi t to the display
area.
ENGLISH
1) Adjust the H.Position so that the left side of the picture frame will move to the left edge
of the display area.
2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Pixel Clock.
NOTE
When the left side of the picture frame moves apart from the left edge of the display
area during the Pixel Clock adjustment, adjust steps 1) and 2).
Another way to make the Pixel Clock adjustment is to correct the vertical wavy lines
in the zebra pattern.
The picture may fl icker during the Pixel Clock, H.Position and V.Position adjustment.
In case the picture frame is bigger or smaller than the data display area after the
Pixel Clock adjustment, repeat steps from
24 OPERATING THE MONITOR
.
Adjust the Phase to correct horizontal wavy noise, fl icker or blur in the zebra pattern.
NOTE
In case the strong fl icker or blurs remain on a part of the screen, repeat steps
because the Pixel Clock may not be adjusted correctly.
Adjust the H.Position after the Phase adjustment if the horizontal position moves
during the adjustment.
Adjust the Brightness and Color to get the desired picture after you complete the Pixel
Clock and Phase adjustments.
Put back your favorite wallpaper.
and
ENGLISH
OPERATING THE MONITOR 25
POWER MANAGEMENT FEATURE
0 0.5W100%
POWER
CONSUMPTION
Blue
Orange
Power Indicator
NORMAL MODE
POWER MANAGEMENT MODE
The power management feature of this product complies with power saving requirement of VESA
DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor
when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer.
There is a power management step the monitor takes as described below. The power management
function, including any timer settings is confi gured by the operating system. Check your operating
system manual for information on how this can be confi gured.
Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off , the
monitor enters into Power Management Mode which reduces the power consumption to less
than 0.5W. The screen becomes dark, and the power indicator turns to orange. From Power
ENGLISH
Management Mode, the image reappears in several seconds when either the keyboard or the
mouse are touched again.
NOTE
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly.
26 OPERATING THE MONITOR
TROUBLE SHOOTING
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem
you have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot fi nd an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
3. If you are experiencing a problem which is not described below or you cannot correct the
problem, discontinue using the monitor and contact your dealer or iiyama service center for further
assistance.
ProblemCheck
The picture does
not appear.
The Power Cable is fi rmly seated in the socket.
(Power indicator
does not light up.)
(Power indicator
is blue.)
(Power indicator
is orange.)
The screen is not
synchronized.
The screen
position is not in
the center.
The Power Switch is turned ON.
The AC socket is live. Please check with another piece of equipment.
If the blank screen saver is in active mode, touch the keyboard or the
mouse.
Increase the Contrast and/or Brightness.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specifi cation of the monitor.
If the monitor is in power management mode, touch the keyboard or the
mouse.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specifi cation of the monitor.
The Signal Cable is properly connected.
The signal timing of the computer is within the specifi cation of the monitor.
The video output level of the computer is within the specifi cation of the
monitor.
The signal timing of the computer is within the specifi cation of the monitor.
ENGLISH
The screen is too
bright or too dark.
The video output level of the computer is within the specifi cation of the
monitor.
TROUBLE SHOOTING 27
ProblemCheck
The screen is
shaking.
No sound.
The sound is too
loud or too quiet.
ENGLISH
A strange noise is
heard.
The power voltage is within the specifi cation of the monitor.
The signal timing of the computer is within the specifi cation of the monitor.
The audio equipment (computer etc.) is ON.
The Audio Cable is properly connected.
The Volume is turned up.
The Mute is OFF.
The audio output level of the audio equipment is within the specifi cation of
the monitor.
The audio output level of the audio equipment is within the specifi cation of
the monitor.
The Audio Cable is properly connected.
RECYCLING INFORMATION
For better environment protection please don't dispose your monitor.
Please visit our web site: www.iiyama.com for monitor recycling.
28 TROUBLE SHOOTING / RECYCLING INFORMATION
APPENDIX
Design and specifi cations are subject to change without prior notice.
Connector shape
Input Audio Connectorø 3.5mm mini jack (Stereo)
Input Audio Signal1.0Vrms maximum
Headphone Connectorø 3.5mm mini jack (Stereo)
Speakers2W × 2 (Stereo speakers)
Maximum Screen Size527.0mm W × 296.5mm H / 20.7" W × 11.7" H
Power Source100-240VAC, 50/60Hz, 1.5A
Pixel pitch0.275mm H × 0.275mm V
Brightness250cd/m2 (Typical)
Contrast ratio3000 : 1 (Typical), Adv. Contrast Function Available
Viewable angleRight / Left : 89 ° each, Up / Down : 89 ° each (Typical)
Response time4ms (Gray to Gray)
5 to 35°C / 41 to 95°F
10 to 80% (No condensation)
-20 to 60°C / -4 to 140°F
5 to 85% (No condensation)
ENGLISH
NOTE
*
Audio/USB equipment is not connected.
APPENDIX 29
SPECIFICATIONS : ProLite X2483HSU
Size Category24"
Panel technology
SizeDiagonal: 23.8" (60.5cm)
LCD
Panel
Pixel pitch0.275mm H × 0.275mm V
Brightness250cd/m
Contrast ratio3000 : 1 (Typical), Adv. Contrast Function Available
Viewable angleRight / Left : 89 ° each, Up / Down : 89 ° each (Typical)
Connector shape
Input Audio Connectorø 3.5mm mini jack (Stereo)
Input Audio Signal1.0Vrms maximum
Headphone Connectorø 3.5mm mini jack (Stereo)
Speakers2W × 2 (Stereo speakers)
Maximum Screen Size527.0mm W × 296.5mm H / 20.7" W × 11.7" H
Power Source100-240VAC, 50/60Hz, 1.5A