TABLE OF CONTENTS
SAFETY PRECAUTIONS............................................
1
1
3
3
FOR YOUR SAFETY............................................................
USER MANUAL
Thank you very much for choosing the iiyama Vision Master color monitor.
We recommend that you take a few minutes to read carefully through this brief but
comprehensive manual before installing and switching on the monitor. Please keep
this manual in a safe place for your future reference.
CUSTOMER SERVICE................................................
CLEANING...................................................................
BEFORE YOU OPERATE THE MONITOR..........................
FEATURES..................................................................
OPERATING THE MONITOR................................................
ADJUSTMENT MENU CONTENTS
..............................
POWER MANAGEMENT FEATURE.............................
TROUBLE SHOOTING........................................................
APPENDIX............................................................................
4
4
4
5
5
6
7
CONNECTING YOUR MONITOR.................................
ACCESSORIES...........................................................
14
16
16
17
17
8
9
13
PRESET MODES.........................................................
CONNECTOR PIN ASSIGNMENT.................................
SPECIFICATIONS.......................................................
FOR WINDOWS 95/98/2000/ME/XP USERS...............
LOCATION OF CONTROLS........................................
MA203DT D
DEUTSCH
FRANCAIS
NEDERLANDS
ENGLISH
SVENSKA
ITALIANO
OPTIONAL PARTS.....................................................
ENGLISH
Congratulations!
The display you have just purchased carries the TCO’03
Displays label. This means that your display is designed,
manufactured and tested according to some of the strictest
quality and environmental requirements in the world. This makes
for a high performance product, designed with the user in focus
that also minimizes the impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
• Good visual ergonomics and image quality in order to improve the working environment for the
user and to reduce sight and strain problems. Important parameters are luminance, contrast,
resolution, reflectance, colour rendition and image stability.
Energy
• Energy-saving mode after a certain time – beneficial both for the user and the environment
• Electrical safety
Emissions
• Electromagnetic fields
• Noise emissions
Ecology
• The product must be prepared for recycling and the manufacturer must have a certified
environmental management system such as EMAS or ISO 14 001
• Restrictions on
o chlorinated and brominated flame retardants and polymers
o heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO Development in cooperation
with scientists, experts, users as well as manufacturers all over the world. Since the end of the
1980s TCO has been involved in influencing the development of IT equipment in a more userfriendly direction. Our labelling system started with displays in 1992 and is now requested by
users and IT-manufacturers all over the world.
For more information, please visit
www.tcodevelopment.com
ENGLISH
FCC DECLARATION OF CONFORMITY
Model Number: MA203DT D
Trade Name: iiyama
Responsible party: IIYAMA North America, Inc.
Address: 65 West Street Road, Suite 101B, Warminster, PA 18974 U.S.A.
Telephone number: 215-682-9050
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This equipment may not cause harmful interference, and (2) this equipment must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If you determine the equipment does cause harmful interference to radio or
television reception (this may be determined by monitoring the interference while turning the equipment off
and on), you are encouraged to try to correct the interference by one of the following measures:
n Reorient or relocate the receiving antenna.
n Increase the separation between the equipment and receiver.
n Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
n Consult the dealer or an experienced radio or TV technician for help.
To meet the FCC requirements, the specified signal cables below should be used.
Signal Cable MB38 (Enclosed): 242Z050-01
Signal Cable MB31 (Optional): 242Z017-01
CE MARKING DECLARATION OF CONFORMITY
This Color Data Monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive”,
73/23/EEC “Low Voltage Directive” as amended by Directive 93/68/EEC and 93/42/EEC “Medical Devices
Directive”.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential
areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the
buildings. All places of operation are characterized by their connection to the public low voltage power supply
system.
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
as set out in the radio interference regulation of the Canadian department of communications.
CANADIAN DEPARTMENT OF COMMUNICATIONS COMPLIANCE
STATEMENT
n We reserve the right to change specifications without notice.
n All trademarks used in this user manual are the property of their respective owners.
n As an E
NERGY STA R
®
Partner, iiyama has determined that this product meets the ENERGY STAR® guidelines for
energy efficiency.
CAUTION Changes or modifications not expressly approved by iiyama could void the users authority
to operate the equipment under FCC compliance regulations.
ENGLISH
FOR YOUR SAFETY
SAFETY PRECAUTIONS
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the
monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous
and can cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
any object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use the monitor where water may be splashed or spilt on the monitor as it may cause fire
or electric shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage
will cause malfunction and may cause fire or electric shock.
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, or dusty or
smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where
the sun shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not
pull the cables and possibly cause injury.
1 FOR YOUR SAFETY
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as
it may cause electric shock.
ENGLISH
CAUTION
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the cabinet bottom will
be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cables are disconnected. If you do not disconnect them, it may cause fire or electric shock.
It is recommended that two people are used when moving the monitor.
UNPLUG THE MONITOR
The power cable is the disconnect device. If the monitor is not in use for a long period of time it is
recommended that the power cable it is left unplugged to avoid accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable
itself as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
DO NOT PUT FLOPPY DISKS NEAR THE MONITOR
Magnetic data recordings such as on a floppy disk may disappear if they are placed on or near the
monitor as the degauss circuit causes a strong momentary magnetic field.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may
damage your computer.
OTHERS
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24
inches) away from your eyes. When using the monitor over a prolonged time, a ten minute break
every hour is recommended as looking at the screen continuously can cause eye strain.
MAGNETIC FIELD INFLUENCE
Place the monitor away from TV, speaker systems or any other source of strong magnetic fields.
The monitor may be noisy or the screen's output may be distorted as a result of interference from
other appliances.
INTENDED APPLICATION
The monitor can be also used in a medical environment to display video signal from computer or
other system. The monitor is not suitable for use in areas that patients are cared for.
FOR YOUR SAFETY 2
ENGLISH
NOTE
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
n
3 FOR YOUR SAFETY
n
CUSTOMER SERVICE
CLEANING
CABINET
CRT
WARNING
CAUTION
NOTE
Stains can be removed with a cloth lightly moistened with a mild detergent solvent.
Then wipe the cabinet with a soft dry cloth.
Wipe the CRT with an enclosed cleaning cloth to remove smudges (such as
fingerprints). Tough stains can be removed with a cloth lightly moistened with water
or mild detergent diluted by 10%. Make sure to wipe the CRT surface using a sideling
movement.
For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
n
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service
center.
n
The CRT screen is protected by an anti-reflection & anti-static coating. Do not scratch or
rub the screen with a hard object, as this could damage the coating.
n
Never use any of the following strong solvents. These will damage the cabinet and
the CRT.
n
Thinner
Benzine
Abrasive cleaner
Solvent for cleaning glass
Solvent with anti-static agent
Spray-type cleaner
Wax
Acid or Alkaline solvent
Alcohol solvent
OTHERS
UNSUITABLE LOCATION FOR USING THE MONITOR
The monitor is not suitable for use in the presence of a FLAMMABLE ANAESTHETIC MIXTURE WITH
AIR or WITH OXYGEN OR NITROUS OXIDE.
The monitor is not suitable for use in areas that patients are cared for. This encloses a space
within the room 1.83 m (6 feet) beyond the perimeter of the bed (examination table, dental chair,
treatment booth, and the like) in its intended location, and extending vertically 2.29 m (7-1/2 feet)
above the floor.
ENGLISH
BEFORE YOU OPERATE THE MONITOR 4
BEFORE YOU OPERATE THE MONITOR
Crisp, Clear Display for Windows® or Macintosh
Supports Resolutions up to 1920×1440
FEATURES
n
n
ACCESSORIES
Power Management (ENERGY STAR® and VESA DPMS Compliant)
Space Saving, Compact Case Design
Ergonomic Design: TCO ’03 and MPR
33
33
3 Approved
The following accessories should be included in the Vision Master packaging. Please ensure that
all of them are enclosed.
Power Cable *
Cleaning Cloth
u
u
u
u
u
u
Supports Refresh Rate up to 85Hz at 1600×1200u
n Signal Cable MB38 (For D-Sub connection)
CAUTION
* TO USERS IN 120V AREA
The rating of the Power Cable enclosed in 120V area is 10A / 125V. If you are using
a power supply higher than this
rating, then a power cable with a rating of 10A /
250V must be used.
Supports sRGB International Standardu
Medical Standard Compliant
u
Plug & Play VESA DDC2B Compliant (D-Sub Input only)
Windows
®
95/98/2000/Me/XP Compliant
n User Manual
ENGLISH
FOR WINDOWS 95/98/2000/ME/XP USERS
NOTE
For additional information on how to download the driver for your monitor, please
access one of the internet sites noted above.
n
Windows 95/98/2000/Me/XP Monitor Information File for iiyama monitors may be obtained via the
Internet, using the address: http://www.iiyama.com (U.S.A.)
http://www.iiyama.co.uk (U.K.)
Monitor Drivers are not required in most cases for Macintosh or Unix operating
systems. For further information, please contact your computer dealer first for advice.
n
5 BEFORE YOU OPERATE THE MONITOR
ENGLISH
BEFORE YOU OPERATE THE MONITOR 6
LOCATION OF CONTROLS
A
Power Indicator
B
Stand-by Switch
( : Stand-by Symbol)
C
OPQ Button (OPQ)
= Optimize Picture Quality
Switch OPQ function between ON and OFF
whenever pressing the OPQ Button. Turn
ON the OPQ function to get the optimum
picture quality when displaying DVD or other
moving pictures.
[On screen display] OPQ ON:
OPQ OFF:
The OPQ setting is not saved.
The OPQ function is turned OFF
when turning OFF the Power
Switch. Color temperature is
fixed to the factory preset 9300K
while the OPQ function is active.
D
+ Button
E
– Button
F
Menu Button
G
Input Select Button (VIDEO 1/2)
Select either VIDEO IN 1 or 2 for the signal
input when both of the signal inputs are
connected to a signal source. Switch VIDEO
IN 1 and 2 whenever pressing Input Select
Button for 2-3 seconds.
When only one of the two signal
inputs is connected to the signal
source, automatic signal input
selection occurs only with the initial
turning ON of the Power Switch.
H
AC Connector (AC IN)
I
D-Sub mini 15pin Connector (VIDEO IN 1)
J
D-Sub mini 15pin Connector (VIDEO IN 2)
NOTE
NOTE
ENGLISH
Ensure that both the computer and the monitor are switched off.
CONNECTING YOUR MONITOR
A
B
Connect the computer to the monitor with the signal cable. (See page 17 for CONNECTOR
PIN ASSIGNMENT.)
C
Connect the Power Cable to the monitor first and then to the power supply.
The signal cables used for the connection vary by the type of computers you use. An
incorrect connection may cause serious damage to both the monitor and the computer.
The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a
special cable is required please contact your local iiyama dealer or regional iiyama
office.
Make sure you tighten the finger screws at each end of the signal cable.
n
n
NOTE
For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
n
7 BEFORE YOU OPERATE THE MONITOR
ENGLISH
OPERATING THE MONITOR 8
OPERATING THE MONITOR
To create the best picture, your iiyama Vision Master has been preset at the factory with the signal
timings listed on page 17 in
PRESET MODES. If an incorrect picture appears during the operation,
adjust the image by following the procedure shown below to get the desired picture.
After selecting an item in the Main Menu, the adjustments and settings
are made in the Sub-Menu.
For example, to adjust the horizontal screen size, select
(Screen Control) on the Main Menu by using the +/– Buttons. The
Sub-Menu appears when you press the Menu Button.
B
The On Screen Display disappears in optional setting seconds after you stop pressing the
buttons while performing an adjustment. (See page 11 for OSD Off Timer.)
n
n
NOTE
Select (H-Size) on the Sub-Menu by using the +/– Buttons. An
adjustment scale will turn white when you press the Menu Button.
Use the +/– Buttons to adjust the horizontal screen size. See
ADJUSTMENT MENU CONTENTS on next pages for further information.
C
(
Adjustments for Size, Position, Pin-Cushion and Trapezoid are saved for each signal timing.
Except for these adjustments, all other adjustments such as Color, Parallelogram, Convergence,
Moire and Landing have only one setting which applies to all signal timings.
Main Menu appears on the screen when you press the Menu
Button.
H-Size
Screen Control
-
+
Adjustment icon
Adjustment menu
presently selected
The line shows the
progress of the
adjustment being
made.
|||||||||||||||||||||||||
·························
Screen Control
Menu
RB
FUNC
Adjustment icon
Adjustment menu
presently selected
ENGLISH
ADJUSTMENT MENU CONTENTS
Main Menu Sub-Menu
Too dull
Too intense
Too dark
Too bright
NOTE
Color
Control
Problem / Option Button to Press
Color temperature is adjustable sRGB and between approximately
10000K and 4500K. The factory preset is 9300K.
Color temperature is fixed to the factory preset 9300K while the OPQ
function is active.
Return to Menu
Return to Main Menu.
Contrast
Brightness
Color Temp.
COLOR
Reddish white
Bluish white
You can skip the Menu pages and display an adjustment scale directly by using the following
button operations.
l Contrast: Press the +/– Buttons when the Menu is not displayed.
l Brightness: Press the +/– Buttons and then the Menu Button continuously when the
Menu is not displayed.
SWITCHING CONTRAST / BRIGHTNESS ADJUSTMENT
To switch between Contrast and Brightness adjustments, press the Menu Button
within 2 seconds after pressing the +/– Buttons during the direct adjustments above.
NOTE
The On Screen Display disappears approx. 3 seconds after you stop pressing the
buttons while performing the direct adjustment, irrespective of OSD Off Timer setting.
(See page 11 for OSD Off Timer.)
n
Direct
Direct
Direct
n
n
sRGB
Procedure
n To access the sRGB mode, select the Color Temp. function and select 10000K by
pushing the + button. Hold down the + button and sRGB function will be activated.
When this mode is activated the color temperature is approximately 6500K.
n To deactivate the sRGB mode, push the – button while the Color Temp. is selected.
n sRGB is an international standard which defines and unifies the
difference of color appearance between equipment.
n You can not adjust the Contrast and Brightness during sRGB mode
because those settings are locked.
NOTE
n
9 OPERATING THE MONITOR
ENGLISH
OPERATING THE MONITOR 10
Main Menu Sub-Menu
Problem / Option Button to Press
Tilt To correct tilt
Return to Menu
Pin-Cushion
Parallelogram
Return to Main Menu.
To correct distortion
To correct distortion
To correct distortion
To correct distortion
Shape
H-Size
H-Position
V-Size
V-Position
Zoom
Too small
Too large
Too far to the left
Too far to the right
Too small
Too large
Too low
Too high
Return to Menu Return to Main Menu.
Screen
Control
Too small
Too large
Trapezoid
Pin-Balance
ENGLISH
Main Menu Sub-Menu
Problem / Option Button to Press
H-Convergence
H-Moire
Return to Menu Return to Main Menu.
Picture
Quality
To correct misconvergence
for vertical lines
NOTE
To correct vertical
wavy lines
Moiré is the result of interference between the phosphor layout and the
video signal. By changing the horizontal and vertical size, the moiré can be
reduced. You may find the moiré more noticeable depending on the Desktop
Pattern you select. In this case, change the desktop pattern. If moiré is still
noticeable, use this function to reduce the effect. The picture may shake if
extreme moiré correction is performed.
Every time the monitor is switched on,
the monitor is automatically degaussed.
But occasionally the colors change when
moving or swiveling the monitor. In this
case, first try the “Raster Rotation”
adjustment. If the problem persists, select
Degauss.
NOTE
Degauss should not be
repeated continuously.
Wait at least
30 minutes between degaussing
operations. While degaussing, the
picture shakes and a
low sound
occurs but this does not indicate a
problem, it is normal.
Degauss
V-Convergence
To correct misconvergence
for horizontal lines
Top-Left
Top-Right
Bottom-Left
Bottom-Right
To correct
discoloration
To correct
discoloration
To correct
discoloration
To correct
discoloration
Return to Menu Return to Main Menu.
Landing
Raster Rotation
To correct
discoloration
11 OPERATING THE MONITOR
ENGLISH
Sub-Menu
OSD H-Position
OSD V-Position
Function
Deutsch
Français
Nederlands
Svenska
Language
English English
German
French
Dutch
Swedish
Japanese
OSD Off Timer
3 5 15 30 45 sec
You can set the OSD display time to any
one of the above 5 settings.
Japanese
Too far to the left
Too far to the right
Too low
Too high
Main Menu
Problem / Option Button to Press
Return to Menu
Return to Main Menu.
Lockout
All adjustment items except this function
are locked out.
NOTE
Performing this operation resets any adjustment
data made by the user to the factory-preset
frequencies. The following settings made by the
user for signals other than the factory-preset
timings remain unchanged.
H-Size V-Size Pin-Cushion
H-Position V-Position Trapezoid
Factory-preset data is restored.
Any changes are automatically saved in
the memory when the On Screen Display
disappears.
Save Recall
Auto
Turning off the power should be avoided while
using the Menu.
NOTE
Manual
Every time the adjustment is performed,
“Save the changes?” appears on the
screen. Select “Yes” to save the
adjustment data. Select “No” to cancel
the adjustment data so that
the screen
returns to the former condition.
Reset
On
Off Lockout is canceled.
OPERATING THE MONITOR 12
ENGLISH
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not used, during the night and weekends,
to avoid unnecessary power consumption.
NOTE
POWER MANAGEMENT FEATURE
Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the
monitor enters into Power Management Mode which reduces the power consumption to less
than 5W. The screen becomes dark, and the power indicator turns to orange. From Power
Management Mode, the image reappears in 10 seconds when either the keyboard or the mouse
are touched again.
The power management feature of this product complies with every power saving requirement of
E
NERGY STAR
®
and VESA DPMS. When activated, it automatically reduces unnecessary power
consumption of the monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a power management step the monitor takes as described below. The power management
function, including any timer settings is configured by the operating system. Check your operating
system manual for information on how this can be configured.
n
0 5 W 100%
POWER
CONSUMPTION
Green
Orange
Power Indicator
NORMAL MODE
POWER MANAGEMENT MODE
Main Menu Sub-Menu
Option
Help
Information
Help
Off
On
The online balloon help is off.
Every time you select the sub-menu icon,
the online balloon help appears to
indicate the menu contents or adjustment
procedure.
The model name, serial number, current
signal input, and scan rates are displayed
in the function.
Return to Menu
Return to Main Menu.
13 OPERATING THE MONITOR
ENGLISH
The screen
position is not in
the center.
The signal timing of the computer is within the specification of the
monitor.
The screen is
too bright or too
dark.
The screen is
shaking.
Check if there are any sources of strong magnetic fields such as TV,
speakers, etc. nearby.
If yes, remove them from the area of the monitor or change the position/
direction of the monitor to avoid magnetic field interference.
The power voltage is within the specification of the monitor.
The signal timing of the computer is within the specification of the monitor.
Moiré correction is working properly.
C
D
E
The video output level of the computer is within the specification of the
monitor.
The screen may be too bright due to the video output level difference of
the computer. In this case, adjust the Contrast.
TROUBLE SHOOTING
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
1.
Perform the adjustments described in OPERATING THE MONITOR, depending on the problem
you have.
2. Consult the following charts if you cannot find an appropriate adjustment item in OPERATING
THE MONITOR or if the problem persists.
If you are experiencing a problem which is not described below or you cannot correct the
problem, discontinue using the monitor and contact your dealer or iiyama service center for
further assistance.
3.
Problem Check
The picture does
not appear.
(Power indicator
does not light up.)
The Power Cable is firmly seated in the socket.
The Power Switch is turned ON.
The AC socket is live. Please check with another piece of equipment.
o
o
o
(Power indicator
is orange.)
The screen is not
synchronized.
The Signal Cable is properly connected.
The signal timing of the computer is within the specification of the monitor.
The video output level of the computer is within the specification of the
monitor.
A
B
(Power indicator
is green.)
If the monitor is in power management mode, touch the keyboard or the
mouse.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specification of the monitor.
The monitor selects the correct signal input. Press the Input Select
Button once to check.
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
If the blank screen saver is in active mode, touch the keyboard or the mouse.
Increase the Contrast and/or Brightness.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specification of the monitor.
TROUBLE SHOOTING 14
ENGLISH
15 TROUBLE SHOOTING
Normal phenomenon on ‘Diamondtron NF-CRT’ monitors
Misalignment of Aperture Grille
Due to the nature of the Diamondtron NF-CRT, in rare cases, a misalignment of the aperture grille
may happen by the shock or vibration caused during transportation. If a black vertical line appears
on the screen, apply a light shock to the side of the monitor with your hand. If the problem persists,
follow the procedure below.
Display a full white picture and inspect the problem area.
Display a high-white picture that covers the problem area to shoot a strong electron beam.
Leave it for a while, until the problem disappears.
Damper Wires
The two faint horizontal lines that may be visible on the screen are actually the shadows of steel
wires called
Damper Wires. All Diamondtron NF-CRT based monitors have these wires for structural
reasons.
A
B
ENGLISH
22" (20.0" / 51cm viewable), Aperture Grille pitch: 0.24mm,
Diamondtron NF-CRT, 90 degree deflection,
Short persistence phosphor, Anti-reflection & Anti-static coating
CRT
300MHz dot clock
Right / Left: 45 degrees each, Up: 15 degrees, Forward: 5 degrees
TTL, Positive or Negative
Separate sync:
Composite sync:
10 maximum
Factory-presets:
User defined settings:
7
493 × 487 × 479mm / 19.4 × 19.2 × 18.9" (W × H × D), 28kg / 61.7lbs
Operating:
Humidity
Storage/Transport: Temperature -20 to 60°C / -4 to 140°F
Humidity
Analog: 0.7Vp-p (Standard), 75W, Positive
0 to 35°C / 32 to 95°F
Sync Frequency
Video Bandwidth
Input Connector
Plug & Play
Input Sync Signal
Input Video Signal
Standard Screen Size
Number of Signal
Storage
Power Source
Power Consumption
Dimensions, Net Weight
Environmental
Considerations
10 to 80% (No condensation)
5 to 90% (No condensation)
Approvals
TCO ’03, CE, TÜV-GS (EN60950*) / TÜV-GM (EN60601-1*) /
MPR3(prEN50279) / ISO 9241-3/ISO 9241-7/ISO 9241-8, PTB, FCC-B,
UL/C-UL (UL60950, UL2601-1), DHHS, Department of Health (Canada)
* Protection Class: Class 1, EMC Class: Class B, Group 1
D-Sub mini 15pin × 2
VESA DDC2B™
1280 × 1024 at 85HzRecommended Resolution
100-230V , 50/60Hz, 1.85-0.8A ( : Alternating Current Symbol)
140W maximum in normal use
Power management mode: 5W maximum
TTL, Positive or Negative
493mm/19.4"
406mm/16.0"
304mm/12.0"
435.7mm/17.2"
487mm/19.2"
479mm/18.9"
APPENDIX 16
SPECIFICATIONS
APPENDIX
Tilt-Swivel Angle
0.3Vp-p, NegativeSync on green:
Altitude limitations Not more than 12,000m
Temperature
Altitude limitations
Not more than 3,000m
Horizontal: 30.0-117.0kHz, Vertical: 50-180Hz
395mm W × 295mm H / 15.6" W × 11.6" H
ENGLISH
CONNECTOR PIN ASSIGNMENT
PRESET MODES
The following chart indicates the Factory Preset Modes.
Additional adjustments may be required to the factory-presets, because the signal
timings vary depending on the type of graphics board you use.
NOTE
17 APPENDIX
Positive
Positive
Positive
Negative
Negative
1280×1024 @85Hz
1024×768 @85Hz
800×600 @85Hz
640×480 @85Hz
640×480 @60Hz
85.0Hz
68.68kHz
Sync Polarity
Vertical
Frequency
Horizontal
Frequency
VESA Timing Name
Positive
43.27kHz Negative
53.67kHz 85.1Hz Positive
85.0Hz
91.15kHz 85.0Hz Positive
PositivePositive85.0Hz 106.25kHz
1600×1200 @85Hz
H
V
31.47kHz 59.9Hz Negative2
3
4
5
6
7
Positive640×400 @70Hz 31.47kHz 70.0Hz Negative1
n D-Sub mini 15pin
Connector
9
Input Signal
* Compliant to VESA DDC.
Input Signal
3
Red video
Green video / Sync on green
8
Pin
1
2
4
5
6
7
Pin
Blue video
Green video ground
Blue video ground
10
11
12
Data line (SDA) *
13
Ground
Ground
H-Sync / HV-Sync
V-Sync
14
Red video ground
Clock line (SCL) *
15
CLASSIFICATION MARK
WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL HAZARDS ONLY
IN ACCORDANCE WITH UL 2601-1 <43RB>
WITH RESPECT TO ELECTRIC SHOCK, FIRE MECHANICAL
AND OTHER SPECIFIED HAZARDS ONLY
IN ACCORDANCE WITH CAN/CSA C22.2 NO. 601.1,
MEDICAL EQUIPMENT CERTIFIED FOR CANADA <43RB>
IIYAMA CORPORATION
710-1 Kitaowaribe, Nagano-shi 381-0014 Japan
Part No. 870Z257A01
This manual is printed on recycled paper.
Dieses Handbuch ist auf Recyclingpapier gedruckt.
Ce manuel est imprimé sur du papier recyclé.
Deze handleiding is op kringlooppapier gedrukt.
Handboken har tryckts på returpapper.
Questo manuale è stampato su carta riciclata.
Loading...