Iiyama PLL400W, PLL320W User Manual

USER MANUAL

ENGLISH

DEUTSCH

FRANCAIS

NEDERLANDS

Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.

SVENSKA

ITALIANO

FCC DECLARATION OF CONFORMITY

Model Number: PLL400W / PLL320W

Trade Name: iiyama

Responsible party: IIYAMA North America, Inc.

Address: 65 West Street Road, Suite 101B, Warminster, PA18974 U.S.A.

Telephone number: 215-682-9050

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for Class B Personal Computers and

ENGLISH

peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the device is operated in a residential environment. This device generates,

uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If you determine the device does cause harmful interference to radio

or television reception (this may be determined by monitoring the interference while turning the device off and

on), you are encouraged to try to correct the interference by one of the following measures:

n Reorient or relocate the receiving antenna.

n Increase the separation between the device and receiver.

n Connect the device into an outlet on a circuit different from that to which the receiver

is connected.

n Consult the dealer or an experienced radio or TV technician for help.

To meet the FCC requirements, you should use a signal cable with ferrite core at both ends.

CAUTION Changes or modifications not expressly approved by iiyama could void the users authority

to operate the device under FCC compliance regulations.

CANADIAN DEPARTMENT OF COMMUNICATIONS COMPLIANCE STATEMENT

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as

set out in the radio interference regulation of the Canadian department of communications.

CE MARKING DECLARATION OF CONFORMITY

This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/

EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.

The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas,

business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.

All places of operation are characterised by their connection to the public low voltage power supply system.

n We reserve the right to change specifications without notice.

n All trademarks used in this user manual are the property of their respective owners.

n As an E

n This manual is printed on recycled paper.

NERGY STA R

energy efficiency.

Partner, iiyama has determined that this product meets the ENERGY STAR® guidelines for

TABLE OF CONTENTS

FOR YOUR SAFETY ................................................................ 1

SAFETY PRECAUTIONS ................................................... 1

SPECIAL NOTES ON LCD MONITORS ............................... 3

CUSTOMER SERVICE ........................................................ 3

CLEANING ......................................................................... 3

BEFORE YOU OPERATE THE MONITOR .................................. 4

FEATURES ......................................................................... 4

CHECKING THE CONTENTS OF THE PACKAGE ............... 4

OPTIONAL PARTS ............................................................. 4

INSTALLATION OF STAND ................................................ 5

CONTROLS AND CONNECTORS ...................................... 6

PREPARING THE REMOTE CONTROL ............................... 7

CONNECTING YOUR MONITOR ........................................ 8

COMPUTER SETTING ......................................................... 9

BASIC OPERATION ............................................................ 10

OPERATING THE MONITOR ..................................................... 12

ADJUSTMENT MENU CONTENTS ...................................... 13

SCREEN ADJUSTMENTS ................................................... 21

POWER MANAGEMENT FEATURE .................................... 23

TROUBLE SHOOTING .............................................................. 24

APPENDIX A ............................................................................. 25

SPECIFICATIONS ............................................................... 25

DIMENSIONS ...................................................................... 26

COMPLIANT TIMING ........................................................... 26

CONNECTOR PIN ASSIGNMENT ........................................ 27

RS-232C INTERFACE ......................................................... 28

APPENDIX B ............................................................................. 28

ENGLISH

FOR YOUR SAFETY

SAFETY PRECAUTIONS

WARNING

STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE

If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor

and contact your dealer or iiyama service center immediately. Further use may be dangerous and

can cause fire or electric shock.

NEVER REMOVE THE CABINET

High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of

fire or electric shock.

ENGLISH

DO NOT PUT ANY OBJECT INTO THE MONITOR

Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug

your monitor immediately and contact your dealer or iiyama service center. Using the monitor with

any object inside may cause fire, electric shock or damage.

INSTALL THE MONITOR ON A FLAT, STABLE SURFACE

The monitor may cause an injury if it falls or is dropped.

DO NOT USE THE MONITOR NEAR WATER

Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric

shock.

OPERATE UNDER THE SPECIFIED POWER SUPPLY

Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will

cause malfunction and may cause fire or electric shock.

PROTECT THE CABLES

Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy

objects on the cables. If damaged, the cables may cause fire or electric shock.

ADVERSE WEATHER CONDITIONS

It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in

power may cause malfunction. It is also advised not to touch the plug in these circumstances as it

may cause electric shock.

1 FOR YOUR SAFETY

CAUTION

INSTALLATION LOCATION

Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky

areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun

shines directly on the monitor.

DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION

The monitor may topple and cause injury if not suitably located. Please also ensure that you do not

place any heavy objects on the monitor, and that all cables are routed such that children may not pull

the cables and possibly cause injury.

MAINTAIN GOOD VENTILATION

Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause

fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.

Ventilation slots on the back of the cabinet will be blocked and the monitor may overheat if the stand

is removed. This may cause fire or damage. Operating the monitor on its back, side, upside down or

on a carpet or any other soft material may also cause damage.

DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR

When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal

cable is disconnected. If you do not disconnect them, it may cause fire or electric shock. It is

recommended that two people are used when moving the monitor.

UNPLUG THE MONITOR

If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid

accidents.

HOLD THE PLUG WHEN DISCONNECTING

To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself

as this may cause fire or electric shock.

DO NOT TOUCH THE PLUG WITH WET HANDS

Pulling or inserting the plug with wet hands may cause electric shock.

DO NOT TURN ON AND OFF THE POWER FREQUENCY

Do not alternate between turning the power ON and OFF frequency as it may cause damage.

ENGLISH

OTHERS

ERGONOMIC RECOMMENDATIONS

To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.

When using the monitor over a prolonged time, a ten minute break every hour is recommended as

looking at the screen continuously can cause eye strain.

FOR YOUR SAFETY 2

SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with LCD monitors and do not indicate a problem.

NOTE

ENGLISH

When you first turn on the LCD monitor, the picture may not fit in the display area

because of the type of computer that is used. In this case, adjust the picture

position to its correct position.

Due to the nature of the backlight, the screen may flicker during initial use. Turn off

the Power Switch and then turn it on again to make sure the flicker disappears.

You may find slightly uneven brightness on the screen depending on the desktop

pattern you use.

Due to the nature of the LCD screen, an afterimage of the previous screen may

remain after switching the image, when the same image is displayed for hours. In

this case, the screen is recovered slowly by changing the image or turning off the

Power Switch for hours. There is the possibility that the previous screen has been

fixed. Pay attention sufficient when you use LCD Monitor.

Contact your dealer or iiyama service center for the backlight replacement when the

screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.

CUSTOMER SERVICE

NOTE

The fluorescent light used in the LCD monitor may have to be periodically replaced.

For the warranty coverage on this component, please check with local iiyama

service center.

If you have to return your unit for service and the original packaging has been

discarded, please contact your dealer or iiyama service center for advice or

replacement packaging.

CLEANING

WARNING

CAUTION

NOTE

CABINET

LCD

SCREEN

3 FOR YOR SAFETY

Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then

wipe the cabinet with a soft dry cloth.

Periodic cleaning with a soft dry cloth is recommended.

Don't use tissue paper etc. because these will damage the LCD screen.

If you drop any materials or liquids such as water into the monitor when cleaning,

unplug the power cable immediately and contact your dealer or iiyama service center.

For safety reasons, turn off the power switch and unplug the monitor before you

clean it. To protect the LCD panel, do not scratch or rub the screen with a hard object.

Never use any of the following strong solvents. These will damage the cabinet and

the LCD screen.

Thinner

Benzine

Abrasive cleaner

Touching the cabinet with any product made from rubber or plastic for a long time

may cause degeneration or loss of paint on the cabinet.

Spray-type cleaner

Wax

Acid or Alkaline solvent

BEFORE YOU OPERATE THE MONITOR

ProLite L320W-B:

The top of the monitor may become hot during use.NOTE

FEATURES

K ProLite L400W-B1X: 39.6” Wide Screen TFT Color LCD Monitor

ProLite L320W-B: 32” Wide Screen TFT Color LCD Monitor

K Supports Resolutions up to 1280 × 1024 (down scale)

K Super Wide Viewing Angle and High Contrast

K Digital Character Smoothing

K Automatic Set-up

K Plug & Play VESA DDC2B Compliant, Windows

K Power Management (E

NERGY STA R

and VESA DPMS Compliant)

95/98/2000/Me/XP Compliant

K Digital Input for Clear Display

CHECKING THE CONTENTS OF THE PACKAGE

The following accessories are included in your package. Check to see if they are enclosed with the

monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama

office.

n Power Cable* n D-SUB Signal Cable MB37

n DVI-D Signal Cable DV66 n RS-232C Cable SR51

n Stand × 2 n Screw for Stand × 4

n Remote Control n AA Dry Battery × 2

n User Manual

ENGLISH

CAUTION

* The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using

a power supply higher than this rating, then a power cable with a rating of 10A/

250V must be used.

However, All guarantees and warranties are void for any problems or damage

caused by a power cable not supplied by iiyama.

OPTIONAL PARTS

Optional parts as below are available for your LCD monitor. Please contact your local iiyama dealer

or regional iiyama office for them. The Video Adapter enables you to connect the video equipment

to the monitor.

n Video Adapter OVA1-2

BEFORE YOU OPERATE THE MONITOR 4

INSTALLATION OF STAND

CAUTION

The monitor is heavy. Two person handling is recommended.

Install the stand on a stable surface. The monitor may cause injury or damage if it

falls or is dropped.

Do not give a strong impact to the monitor. It may cause damage.

Unplug the monitor before installation to avoid electric shock or damage.n

Install the Stand as shown in the illustration.

Tighten the Screw to fasten the Stand.

ProLite L400W-B1X

ENGLISH

Stand

Screw × 4

ProLite L320W-B

Screw × 4

5 BEFORE YOU OPERATE THE MONITOR

Stand

CONTROLS AND CONNECTORS

<Front>

Power Switch (POWER)

Auto Button (AUTO)

Adjusts Clock, Phase, H-Position and V-Position automatically.

NOTE

n For best results, use the Auto Set-up in conjunction with the test pattern Test.bmp.

(See page 21 for SCREEN ADJUSTMENTS.)

n The screen becomes dark for approximately five seconds during the adjustment.

– / Contrast Button ( – / )

+ / Brightness Button ( + / )

Menu Button (MENU)

Input Button (INPUT)

Remote Sensor

G H Power Indicator

NOTE

Blue: Normal operation

Orange: Power Management

The monitor enters into power management mode which reduces the

power consumption to less than 5W when receiving no horizontal and/or

vertical sync signal.

Optional Video Adapter Slot

DVI-D 24pin Connector (DVI)

D-SUB mini 15pin Connector (D-SUB)

RS-232C Connector (RS-232C)

Handles

AC Connector (AC IN)

Main Power Switch (POWER)

<Back>

BEFORE YOU OPERATE THE MONITOR 6

ENGLISH

Input Button (INPUT)

Auto Button (AUTO)

Adjusts Clock, Phase, H-Position and V-Position

automatically.

NOTE

nFor best results, use the Auto Set-up in conjunction with

the test pattern Test.bmp. (See page 21 for SCREEN

ADJUSTMENTS.)

nThe screen becomes dark for approximately five seconds

during the adjustment.

Zoom + Button ( )

ENGLISH

– Button / Contrast Button ( )

Exit Button (EXIT)

Power Switch (POWER)

Menu Button (MENU)

+ Button / Brightness Button ( )

H I Zoom – Button ( )

PREPARING THE REMOTE CONTROL

To use the remote control, insert the two dry batteries.

CAUTION

Do not use any other batteries other than those specified in this manual for the

Remote Control. Do not insert old and new batteries together in the Remote Control. Make sure that the terminals match the “+” and “–” indications in the battery compartment. Burst batteries or the electrolyte from these batteries may cause stains, fire or injury.

Slide open the battery case lid on the reverse of the remote control as shown in the illustration.

Take care not to mix up the “+” and “–” terminals.

Slide closed the battery case lid.

Push here to slide the battery case lid.

Replace with new batteries when the Remote Control does not work close to the

NOTE

monitor. Use AA dry batteries.

Operate the Remote Control by pointing it toward the Remote Sensor on the monitor.

n n

Other manufacturers remote control will not work with this monitor. Use the provided

Remote Control ONLY.

7 BEFORE YOU OPERATE THE MONITOR

CONNECTING YOUR MONITOR

Ensure that both the computer and the monitor are switched off.

Connect the computer to the monitor with the signal cable. (See page 27 for CONNECTOR PIN

ASSIGNMENT.)

Connect the RS-232C cable to the computer while using the RS-232C control feature. (See page

27 for CONNECTOR PIN ASSIGNMENT.)

Connect the Power Cable to the monitor first and then to the power supply.

NOTE n The signal cables used for connecting the computer and monitor may vary with the type

of computer used. An incorrect connection may cause serious damage to both the

monitor and the computer.

n For connection to Macintosh computers, contact your local iiyama dealer or regional

iiyama office for a suitable adaptor.

n Make sure you tighten the finger screws at each end of the signal cable.

[Example of Connection]

ENGLISH

Computer

RS-232C Cable (Accessory)

D-SUB Signal Cable (Accessory)

DVI-D Signal Cable (Accessory)

Video Adapter OVA1-2 (Optional)

Video Cable(Optional)

S-Video Cable(Not included)

Power Cable(Accessory)

Video equipment

BEFORE YOU OPERATE THE MONITOR 8

+ 25 hidden pages

Iiyama PLL400W, PLL320W User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual