I-Inc iP-221 User Manual

Important Safety Instruction

1. Readthese instructions thorough

ly and keep this user

manual for future use.

2. Do not use the product near water. Never spill liquid of
any kind of the products. Clean LCD monitor when

power off.Never clean it with liquid cleanness or liquefier.
Better

use clean wet cloth carefully.

. Do not place the product on an unstable cart, stand or
table. Doing so may cause the product to fall, which can
seriously damage it.

4. To ensure reliable operation,never block these ventilation

slots by placing the producton a bed, rug or similar
surface; this product should never be placed near or over

a radiator or heat register; or installed in any enclosure

that prevents proper ventilation.

5. Do not place any object on the

power cord. Do not place

this product where persons could walk on the

power cord.

6. Never push objects of any kind through the ventilation

slots at the back of

the product. Todo so could risk fire or

electronic shock.

7.Do not attempt to service this product by yourself. Opening
or removin

g covers may expose you to dangerous voltage
that could cause fire or electronic shock. Refer all
servicing needs to authorized service personnel.
Unplug this product from the wall outlet and contact

authorized service personnel und

er the following

conditions:
a. When the power cord or plug is damaged or frayed.

b. If a liquid has been spilled into or on the product.
c. If the product has been rained or spilled by water.
d. If the product has been dropped or the cabinet has

been damaged.

If the product does not operate normally when

operating instructions arefollowed, and product shows
to be maintained.

Only under normal condition canthe quality of LCD products
be assured

during operation. Normal condition as following:

Temperature:20 ± 15;

Humidity: 52.5 ± 32.5;
Display image: continuously changing image. (Not freezing
image)
For the LCD products, the phenomenon of image stagnation
may appear when display the freezing image for a certain
long time. All the displayproductsincluding LCD may have
this kind of image stagnation, and this is not a kind of defect.
In order to avoid the phenomenon of image stagnation, we
suggest that the screen protection program be set when
your PC or system is spare.

Special Notice

Connection

1.Turn off computer and unplug power cord.

2.To connect signal cable with 15pin into VGA out hole on
the back of monitor, and to be sure to tighten switches
on both ends of signal cable.

3.Toplug PC and monitor power cord to the nearest socket.

4.Turn on PC and monitor, im age possibility shows successful

Power Switch

Press this button to turn on or off the monitor. Note: It will
not cut off power supply. But to unplug pin from the socket.

PowerIndicator

LEDpower indicator
LED-On Normal;
LED flicker:Power Saving;
LED-Off:Power Off.

OperateExplanation

Your LCD has been adjusted to its optimal status before
shipment. You can also adjust the image in accordance
with the following allustrations and steps.

Reset

Restore to factory settings

Primary

Directory

Secondary
Directory

Description

iP221 LCD MONITOR

USER’S GUIDE

3

7.

8.

The device complies with Parts 15 of the FCC Rule.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference;
(2) this device must accept any interference received,
including interference that may cause undesired operations.

e.

Press the “MENU” button to start the OSD feature.
Click the “ ” or “ ” to select the function to be

adjusted.
Click the “MENU” button to access into the function to
be adjusted.
Click “ ” or “ ” button to change the current setting
of the function
To exit OSD MENU or go back to the previous action
by “AUTO”.

To repeat above steps for changing the setting of the
other function.

Contrast

Press “ ” adjust the Contrast.

OSD Control

Brightness

Press “ ” adjust the Brightness.

For similar screen display resolutions, the screen
resolution can be changed by pressing the “AUTO”
key for 3 seconds to achieve the optimal display
quality.

OSD Menu

Source Resolution and Frequency

installation. If not , please double check all the connections.

2. To avoid monitor damaged, please handle the
centre part of front cover while it installation.

NOTES: 1. To connect signal cable and plug power cord to be

assure monitor safety on process of installation.

Front Panel

Controls

Stand Assembly Instruction

MENU

Press it to open the OSD MENU, to select MENU options
when the OSD MENU is displayed.

Hot key to adjust contrast,
Down selection button

AUTO

Hot key to automatically optimize positions, phase and
clock whenOSD isnot shown.Toexit OSD MENUwhen
OSD is shown.

Power on or off;
LED-On Normal;
LED flicker:Power Saving;
LED-Off:Power Off.

Hot key to adjust brightness
Up selection button

1
2
3

4

5

For similar screen display resolutions, the screen
resolution can be changed by pressing the “AUTO” key
for 3 seconds to achieve the optimal display quality.

OSD H. Pos.

Move the OSD left and right on the screen

OSD V.Pos.

Move the OSD up and down on the screen

OSD
Menu

OSD Timer

Adjust OSD display time setting

Language

Select the language you want

Transparen­cy

Adjust OSD Transparency

Primary

Directory

Secondary
Directory

Description

Contrast

Adjust the contrast of the image

Brightness

Adjust the brightness of the screen

Color

Color Temp

Set up the color Temp. to be 9300K 6500K

5500K

USER red, green, blue to adjust red/green/blue

Auto Adjust

Set up to adjust clock, phase and position automatically

H. Position

Move the image left and right on the screen

V.Position

Move the image up and down on the screen

Clock

Adjust the clock pulse of the image

Phase

Adjust the focus of image

Picture

MONITOR INPUT CONNECTIONS:

3. VGA signal input

1. AC power input

This device complies with requirement of EMC directive
2004/108/EC with regard to Electromagnetic Compatibility,
and 73/23/EEC and 93/68/EEC with regard to Low Voltage
directive.

Max resolution

1920x1080/WUXGA

16.7MroloCyalpsiD

Pixel Pitch

0.248mm x 0.248mm
m (typical)/dc052ssenthgirB

Contrast Ratio

1000:1 (typical)

Response time

5ms (typical)

ViewingAngle

170°(H) / 160°(V) (typical)

Display Area

476.64mm(H)

X 268.11mm

(V)

Sync. Frequency

Horizontal 24kHz-83kHz/Vertical 56Hz-75Hz

Power Supply

AC100-240Volt@60/50Hz

Dimension

511 mm (W) X392 mm (H) X 202 mm (D)

Net Weight

4.4 Kg

2

Power Consumption

30W (typical)

Display Mode

VGA 640x480

SVGA 800x600

XGA 1024x768

WXGA 1360x768

47.712 60.015 85.5

Recycling Information

http://www.i-inc-usa.com/

Others

Signal
Selection

Select D-SUB signal or DVI signal (optional)

Adjust the volume of the audio (optional)

MODE

Select PC GAME MOVIE display mode

Aspect
Ratio

Audio
Volume

Select 16:9 AUTO 4:3 display image

WXGA +1440x900

55.935 59.887 106.5

WXGA +1600x900

60 60 108

WUXGA 1920x1080

67.500 60.000 148.500

D-SUB(VGA)

POWER

DVI

2. DVI signal input