Page 1
Draco ultra DisplayPort
490 Series
KVM Extender
User Manual
Edition: 2016-02-29
IHSE GmbH Maybachstraße 11 88094 Oberteuringen Germany
info@ihse.com
www.ihse.com phone: +49 7546-9248-0 fax: +49 7546-9248-48
Page 2
Draco ultra DisplayPort KVM Extender
Copyright
© 2016. All rights reserved. This information may not be reproduced in any
manner without the prior written consent of the manufacturer.
Information in this document is subject to change without notice.
Trademarks
All trademark and trade names mentioned in this document are
acknowledged to be the property of their respective owners.
Disclaimer
While every precaution has been taken during preparation of this manual,
the manufacturer assumes no liability for errors or omissions. The
manufacturer assumes no liability for damages resulting from the use of
the information contained herein.
The manufacturer reserves the right to change specifications, functions, or
circuitry of the product without notice.
The manufacturer cannot accept liability for damage due to misuse of the
product or due to any other circumstances outside the manufacturer’s
control (whether environmental or installation related). The manufacturer
shall not be liable for any loss, damage, or injury arising directly, indirectly,
incidentally, or consequently from the use of this product.
2 2016-02-29
Page 3
Contents
Contents
1 About This Manual ....................................................................... 7
1.1 Scope.................................................................................. 7
1.2 Validity ................................................................................ 7
1.3 Cautions and Notes ............................................................ 7
2 Safety Instructions....................................................................... 8
3 Description ................................................................................... 9
3.1 Application .......................................................................... 9
3.2 System Overview .............................................................. 10
3.3 Product Range .................................................................. 11
3.3.1 Part Numbers ...................................................... 11
3.3.2 Chassis ............................................................... 11
3.3.3 KVM Extender Modules ...................................... 12
3.3.4 Upgrade Modules................................................ 12
3.3.5 USB 2.0 Extender Modules................................. 13
3.3.6 Monitoring Modules............................................. 14
3.4 Accessories Upgrade Kits ................................................. 14
3.5 Accessories....................................................................... 15
3.6 Device Views .................................................................... 16
3.6.1 2-fold Vario Chassis 474-BODY2/2R .................. 16
3.6.2 2-fold Vario Chassis 474-BODY2N ..................... 16
3.6.3 4-fold Vario Chassis 474-BODY4/4R .................. 17
3.6.4 6-fold Vario Chassis 474-BODY6R ..................... 18
3.6.5 6-fold Vario Chassis 474-BODY6BP................... 19
3.6.6 6-fold Vario Chassis 474-BODY6BPF................. 20
3.6.7 21-fold Vario Chassis 474-BODY21R ................. 21
3.6.8 Model L- / R490-BPHC ....................................... 22
3.6.9 Model L- / R490-BPHS / -BPHX.......................... 22
3.6.10 Model L- / R490-BPHCR..................................... 23
3.6.11 Model L- / R490-BPHSR / -BPHXR .................... 23
3.6.12 Model L- / R474-BXH.......................................... 24
2016-02-29 3
Page 4
Draco ultra DisplayPort KVM Extender
3.6.13 Model L- / R474-BXE .......................................... 24
3.6.14 Model L- / R474-BUE.......................................... 24
3.6.15 Model L- / R474-BXE2 ........................................ 25
3.6.16 Model L- / R474-BAX / -BSX............................... 25
3.6.17 Model L- / R474-BAP .......................................... 25
3.6.18 Model L- / R474-BBX .......................................... 26
3.6.19 Model L- / R474-BDX.......................................... 26
3.6.20 Model L- / R474- BXTC and L- / R474-BXUC..... 27
3.6.21 Model L- / R474- BXTS and L- / R474-BXUS ..... 27
3.6.22 Model L- / R474- BXEC....................................... 28
3.6.23 Model L- / R474- BXECR.................................... 28
3.6.24 Model L- / R474-BXES........................................ 29
3.6.25 Model L- / R474- BXESR .................................... 29
3.6.26 Model 474-SNMP................................................ 30
3.7 Status LEDs ...................................................................... 31
3.7.1 Status KVM Extender Module............................. 31
3.7.2 Status Upgrade Module Digital Audio ................. 32
3.7.3 Status Upgrade Module Balanced Audio ............ 33
3.7.4 Status Upgrade Module USB-HID....................... 34
3.7.5 Status Upgrade module USB 2.0 embedded ...... 35
3.7.6 Status Upgrade Module USB 2.0 V1................... 36
3.7.7 Status Upgrade Module USB 2.0 V2................... 37
3.7.8 Status Monitoring Module SNMP ........................ 39
4 Installation .................................................................................. 40
4.1 Package Contents............................................................. 40
4.2 System Setup.................................................................... 42
4.2.1 KVM Extender Setup .......................................... 42
4.2.2 Setup of Upgrade Modules ................................. 43
4.3 Example Applications........................................................ 44
4.4 Overview Upgrade Modules.............................................. 46
5 Configuration.............................................................................. 47
5.1 Transmission Parameters ................................................. 47
4 2016-02-29
Page 5
Contents
5.2 DDC Settings .................................................................... 47
5.3 Command Mode ............................................................... 48
5.4 USB-HID Ghosting............................................................ 50
5.5 Configuration File.............................................................. 51
5.5.1 Parameters for CPU Units................................... 51
5.5.2 Parameters for CON Units .................................. 53
5.5.3 Parameters for CPU und CON Units................... 54
6 Operation .................................................................................... 55
6.1 Download of DDC Information .......................................... 55
6.2 Shared Operation of redundant CPU Units ....................... 55
7 Specifications............................................................................. 57
7.1 Interfaces .......................................................................... 57
7.1.1 DisplayPort.......................................................... 57
7.1.2 USB-HID ............................................................. 57
7.1.3 PS/2 .................................................................... 58
7.1.4 USB 2.0 (transparent) ......................................... 58
7.1.5 RJ45 (Interconnect) ............................................ 59
7.1.6 Fiber SFP Type LC (Interconnect) ...................... 59
7.1.7 Serial Interface.................................................... 59
7.1.8 Serial Interface RS422 ........................................ 60
7.1.9 Analog Audio Interface........................................ 61
7.1.10 Digital Audio Interface......................................... 62
7.1.11 Balanced Audio Interface.................................... 63
7.2 Interconnect Cable............................................................ 66
7.2.1 Cat X ................................................................... 66
7.2.2 Fiber.................................................................... 67
7.3 Supported Peripherals ...................................................... 68
7.3.1 USB-HID Devices ............................................... 68
7.3.2 USB 2.0 Devices ................................................. 68
7.4 Connector Pinouts ............................................................ 69
7.5 Power Supply.................................................................... 73
7.6 Environmental Conditions ................................................. 74
2016-02-29 5
Page 6
Draco ultra DisplayPort KVM Extender
7.7 Size................................................................................... 74
7.8 Shipping Weight................................................................ 76
8 Troubleshooting......................................................................... 77
8.1 General Failures ............................................................... 77
8.2 Blank Screen..................................................................... 78
8.3 USB-HID ........................................................................... 79
8.4 Serial Connection.............................................................. 80
8.5 Analog Audio..................................................................... 80
8.6 Digital Audio...................................................................... 81
8.7 Upgrade Module USB-HID................................................ 82
8.8 USB 2.0 embedded........................................................... 83
8.9 USB 2.0............................................................................. 84
9 Technical Support ...................................................................... 85
9.1 Support Checklist.............................................................. 85
9.2 Shipping Checklist ............................................................ 85
10 Certificates.................................................................................. 86
10.1 CE Declaration Of Conformity........................................... 86
10.2 North American Regulatory Compliance ........................... 87
10.3 Product Safety ..................................................................87
10.4 WEEE ............................................................................... 88
10.5 RoHS/RoHS 2................................................................... 88
11 Glossary...................................................................................... 89
Pos: 1 /806-IHSE/Zu diesem Handbuch/ATB_Zu diesem Handbuc h @ 5\mod_1278573163276_6. doc @ 41510 @ 1222 @ 1
6 2016-02-29
Page 7
About This Manual
1 About This Manual
1.1 Scope
This manual describes how to install your KVM Extender, how to operate it
and how to perform trouble shooting.
1.2 Validity
This manual is valid for all devices listed on the front page. The product
code is printed on the base of the devices.
1.3 Cautions and Notes
The following symbols are used in this manual:
This symbol indicates an important operating instruction that should be
followed to avoid any potential damage to hardware or property, loss of
data, or personal injury.
This symbol indicates important information to help you make the best use
of this product.
This symbol indicates best practice information to show recommended
and optimal ways to use this product in an efficient way.
Pos: 2 /806-IHSE/Sicherheitshinweise/ATB_Sic herheitshinweise @ 5\m od_1278573321245_6. doc @ 41528 @ 1 @ 1
2016-02-29 7
Page 8
Draco ultra DisplayPort KVM Extender
2 Safety Instructions
To ensure reliable and safe long-term operation of your KVM Extender
please note the following guidelines:
Installation
Only use the device according to this User Manual. Failure to follow
these procedures could result in damage to the equipment or injury to
the user or installer.
Only use in dry, indoor environments.
The KVM Extender and the power supply units can get warm. Do not
install components in an enclosed space without any airflow.
Do not place the power supply directly on top of the device.
Do not obscure ventilation holes.
Only use power supplies originally supplied with the product or
manufacturer-approved replacements. Do not use a power supply if it
appears to be defective or has a damaged chassis.
Connect all power supplies to grounded outlets. In each case, ensure
that the ground connection is maintained from the outlet socket
through to the power supply's AC power input.
Do not connect the link interface to any other equipment, particularly
network or telecommunications equipment.
Take any required ESD precautions.
In order to disconnect the device completely from the electric circuit, all
power cables have to be removed.
Repair
Do not attempt to open or repair a power supply unit.
Do not attempt to open or repair the KVM Extender. There are no
user serviceable parts inside.
Please contact your dealer or manufacturer if there is a fault.
Pos: 3 /806-IHSE/Beschreibung/UEB_Beschreibung @ 5\ mod_1278573379151_6. doc @ 41546 @ 1 @ 1
8 2016-02-29
Page 9
Description
3 Description
Pos: 4 /806-IHSE/Beschreibung/Verwendungszweck/ 474-xx @ 6\mod_1304579 672848_6.doc @ 50785 @ 2 @ 1
3.1 Application
The KVM Extender is used to increase the distance between a source
(computer, CPU) and its console (keyboard, mouse, and other peripheral
devices).
The KVM Extender is designed for use with Cat X (Twisted Pair)
interconnect cables or fiber interconnect cables.
The KVM Extender with Cat X interconnect cables is unsuitable for
connection between buildings where a fiber optic based product should be
used instead.
The KVM Extender with fiber interconnect cables can also be used with
applications in environments which are subject to electromagnetic
interference. Electromagnetic interference can limit the maximum distance
and reliability of operation.
Pos: 5 /806-IHSE/Beschreibung/System-Übersic ht /474-xx @ 6\mod_1304579 735410_6.doc @ 50803 @ 2 @ 1
2016-02-29 9
Page 10
Draco ultra DisplayPort KVM Extender
3.2 System Overview
The KVM Extender consists of at least one CPU module and one
CON module. The various modules are summarized respectively in a
vario chassis (2-fold, 4-fold or 6-fold) at CPU site and CON site (CPU and
CON Unit).
The CPU module is connected directly to the source (computer, CPU)
using the supplied cables.
The CON module is connected to the console (monitor, keyboard and
mouse).
The CPU Unit and the CON modules communicate with each other
through the interconnect cables.
1
2
3
4
5
6
7
System Overview
1 Source (computer, CPU)
2 KVM Extender CPU Unit
3 Interconnect cable
4 KVM Extender CON Unit
5 Console (monitor, keyboard, mouse)
6 Second monitor (option, only with Dual-Head devices)
7 USB-HID devices (option, only with 4x USB-HID devices)
See Chapter 4.3, Page 44 for installation examples.
Pos: 6 /806-IHSE/Beschreibung/Gerätetypen/490- xx @ 15\mod_14552813471 99_6.doc @ 165580 @ 2333333 @ 1
10 2016-02-29
Page 11
Description
3.3 Product Range
3.3.1 Part Numbers
Part numbers for Connections via Cat X or Fiber Cable
All devices are available in the following versions:
Connection via Cat X cable (x = "C")
Connection via Single-mode fiber cable (x = "S")
High speed connection (3.125 Gbit/s) via Single-mode fiber cable
(x = "X")
Fiber devices can be used with Multi-mode and Single-mode cables (see
Chapter 7.2.2, Page 67).
Part numbers for CPU Unit and CON Unit
The part numbers for the CPU Unit and the CON Unit can be derived from
the part number of the complete device.
CPU Unit: L490
CON Unit: R490
All devices in the K474 series are technically compatible with devices in
the K477 series.
3.3.2 Chassis
Model Description
474-BODY2
474-BODY2R
474-BODY2N
474-BODY4
474-BODY4R
Empty chassis for up to 2 boards, 1x external power
supply unit
Empty chassis for up to 2 boards, 1x external power
supply unit, preparation for redundancy for a second
power supply unit (external)
Empty chassis for up to 2 boards, 1x internal power
supply unit, preparation for redundancy for a second
power supply unit (external)
Empty chassis for up to 4 boards, 1x external power
supply unit
Empty chassis for up to 4 boards, 1x external power
supply unit, preparation for redundancy for a second
power supply unit (external)
2016-02-29 11
Page 12
Draco ultra DisplayPort KVM Extender
Model Description
474-BODY6R
474BODY6BP
474BODY6BPF
474BODY21/4U
Empty chassis for up to 6 boards, 1x internal power
supply unit, preparation for redundancy for a second
power supply unit (external)
Empty chassis for up to 6 boards, active backplane, 2x
internal power supply unit (redundancy)
Empty chassis for up to 6 boards, active backplane, 2x
internal power supply unit (redundancy) with connectors
on rear side
Empty chassis for up to 21 boards, 1x internal power
supply unit, preparation for redundancy for a second
power supply unit (internal)
3.3.3 KVM Extender Modules
Model Description
L490-BPHx
R490-BPHx
L490-BPHxR
R490-BPHxR
Single-Head module for 1x DisplayPort
(up to 4096x2160@60Hz) with 2x USB-HID
Single-Head module for 1x DisplayPort
(up to 4096x2160@60Hz) with 2x USB-HID and
redundant connector for interconnect cables
3.3.4 Upgrade Modules
Model Description
L474-BXH
R474-BXH
L474-BXE
R474-BXE
L474-BXE2
R474-BXE2
L474-BAX
R474-BAX
L474-BBX
R474-BBX
L474-BAP
R474-BAP
Upgrade module with 2x USB-HID
Upgrade module with 2x USB 2.0
Upgrade module with 4x USB 2.0
Upgrade module with Analog Audio / Serial RS232
(bidirectional)
Upgrade module with balanced analog Audio
(unidirectional)
Upgrade module with Analog Audio / Serial RS232
(bidirectional) and PS/2
12 2016-02-29
Page 13
Description
Model Description
L474-BSX
R474-BSX
L474-BXP
R474-BXP
L474-BDX
R474-BDX
L474-BAH
R474-BAH
L474-BUE
R474-BUE
L474-BAE
R474-BAE
L474-BDH
R474-BDH
L474-BDE
R474-BDE
L474-BDD
R474-BDD
L474-BDA
R474-BDA
Upgrade module with Analog Audio / Serial RS422
(bidirectional)
Upgrade module with PS/2 (only available with upgrade
module Analog Audio / Serial)
Upgrade module with Digital Audio (unidirectional)
Upgrade module with Analog Audio / Serial RS232
(bidirectional) and 2x USB-HID
Upgrade module with Analog Audio (bidirectional) and
2x USB 2.0
Upgrade module with Analog Audio / Serial RS232
(bidirectional) and 2x USB 2.0
Upgrade module with Digital Audio (unidirectional) and
2x USB-HID
Upgrade module with Digital Audio (unidirectional) and
2x USB 2.0
Upgrade module with Digital Audio (bidirectional)
Upgrade module with Digital Audio (unidirectional) and
Analog Audio / Serial (bidirectional)
3.3.5 USB 2.0 Extender Modules
Model Description
L474-BXTx
R474-BXTx
L474-BXUx
R474-BXUx
L474-BXEx
R474-BXEx
L474-BXExR
R474-BXExR
USB 2.0 upgrade module with 4x USB 2.0
(based on: ICRON 2100 core)
Note: Replacement product L/R-474-BXUx; not
compatible to replacement product
USB 2.0 upgrade module with 4x USB 2.0
(based on: ICRON 2300 Core)
USB 2.0 upgrade module with 4x USB 2.0, plug and
play (based on: ICRON 2300 Core)
USB 2.0 upgrade module with 4x USB 2.0 and
redundant connector for interconnect cables, plug and
play (based on: ICRON 2300 Core)
2016-02-29 13
Page 14
Draco ultra DisplayPort KVM Extender
Pos: 7 /806-IHSE/Beschreibung/Überwachungsmodu le/474-xx @ 14\mod_141 5202166328_6.doc @ 157997 @ 3 @ 1
3.3.6 Monitoring Modules
Model Description
474-SNMP
SNMP module for monitoring of extenders in the chassis
474-BODY6BP/F and 474-BODY21
Pos: 8 /806-IHSE/Beschreibung/Einbauoptionen/ 474-xx @ 6\mod_13045800 08551_6.doc @ 50839 @ 2 @ 1
3.4 Accessories Upgrade Kits
Model Description
474-2RMK 19"/1U rack mount kit for 2-fold chassis
Pos: 9 /806-IHSE/Beschreibung/Zubehör/474-xx @ 11\ mod_1391589410653_ 6.doc @ 132450 @ 2 @ 1
4742NRMK
474-4RMK 19"/1U rack mount kit for 4-fold chassis
474-6RMK 19"/1U rack mount kit for 6-fold chassis
474-
VPLATE
474-
BRACKET
474-
OPTRED
474-PSU2 Power supply for 2-fold chassis (spare or redundancy)
474-PSU4 Power supply for 4-fold chassis (spare or redundancy)
474-PSU6 Power supply for 6-fold chassis (spare or redundancy)
474-PSU21 Power supply for 6-fold-chassis (spare or redundancy)
474-BLND1 Blind plate 3U/4HP for 2-, 4- and 6-fold chassis
474-BLND2 Blind plate 3U/8HP for 2-, 4- and 6-fold chassis
474-6FAN Fan option for chassis 474-BODY6BP/F
KVM Extenders and the power supply units can get warm and must not be
installed in closed rooms with no air circulation. For rack-mount
installations, at least 0.5 U (height unit) is required above the KVM
Extender for ventilation.
19"/1U rack mount kit for 2-fold chassis with internal PSU
Fastening strips for screw or snap on for 2-, 4- and 6-fold
chassis
Mounting bracket with screws for 2-, 4- and 6-fold chassis
Retrofitting for redundant power supply option (without
power supply) for 2- and 4-fold chassis
14 2016-02-29
Page 15
Description
3.5 Accessories
Model Description
026-2A Serial cable 1.8 m (RS232)
247-U1 USB cable 1.8 m (Type A to B)
260-5G International power supply unit 100...240VAC / 5VDC / 3 A
260-5U International power supply unit 100...240VAC / 5VDC / 4 A
436-AA VGA cable 1.8 m (VGA to DVI-I)
436-ID DVI-D cable 1.8 m (DVI-D)
445-2H DVI-D splitter cable
436-HD HDMI cable 1.8 m
436-DP DisplayPort cable 1.8 m
455-CK Stereo jack cable 1.6 m (3.5 mm Stereo)
455-CR RCA cable 2.5 m (Cinch male connector)
455-CT TOSLINK cable 1.8 m (F05 male connector)
455-CX Mini-XLR cable 1.8 m (3 pole)
474-
IECLOCK
Pos: 10 /806-IHSE/Beschreibung/Geräteansichte n/UEB_Geräteansic hten @ 5\mod_1278573737 808_6.doc @ 41654 @ 2 @ 1
IEC connection cable for power supply, lockable
2016-02-29 15
Page 16
Draco ultra DisplayPort KVM Extender
3.6 Device Views
Pos: 11 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/2-fac h Vario-Gehäuse 474-BODY2/ 2R @ 6\mod_130458028056 6_6.doc @ 50858 @ 3 @ 1
3.6.1 2-fold Vario Chassis 474-BODY2/2R
CPU and CON Unit
3
1
4
2
Rear View
1 Slot for modules #1
2 Connect to 5VDC power supply (standard)
3 Slot for modules #2
4 Connect to 5VDC power supply (redundancy, optional)
Pos: 12 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/2-fac h Vario-Gehäuse 474-BODY2 N @ 8\mod_1348578478411_6. doc @ 69380 @ 3 @ 1
3.6.2 2-fold Vario Chassis 474-BODY2N
CPU and CON Unit
4
2
Rear View
1 Slot for modules #1
2 Connect to power supply (standard)
3 Slot for modules #2
4 Connect to 5VDC power supply (redundancy)
The 2-fold vario chassis with an internal power supply is not equipped with
a fuse on its primary side. Therefore the protection against excessive
currents has to be provided by the electrical installation of the building.
Pos: 13 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/4-fac h Vario-Gehäuse 474-BODY4/ 4R @ 6\mod_130458035909 8_6.doc @ 50876 @ 3 @ 1
3
1
16 2016-02-29
Page 17
Description
3.6.3 4-fold Vario Chassis 474-BODY4/4R
CPU and CON Unit
Rear View
1 Slot for modules #3
2 Slot for modules #1
3 Connect to 5VDC power supply (standard)
4 Slot for modules #4
5 Slot for modules #2
6 Connect to 5VDC power supply (redundancy, optional)
For operation with three KVM Extender CON modules and a USB 2.0
CON module in a 4-fold vario chassis, two power supplies are necessary.
In this case, redundancy is inapplicable.
Pos: 14 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/6-fac h Vario-Gehäuse 474-BODY6 R @ 6\mod_1304580442488_6. doc @ 50894 @ 3 @ 1
4
1
5
2
6
3
2016-02-29 17
Page 18
Draco ultra DisplayPort KVM Extender
3.6.4 6-fold Vario Chassis 474-BODY6R
CPU and CON Unit
Rear View
1 Slot for modules #5
2 Slot for modules #3
3 Slot for modules #1
4 Connect to power supply (standard)
5 Connect to 5VDC power supply (standard)
6 Slot for modules #6
7 Slot for modules #4
8 Slot for modules #2
For operation with KVM Extender modules in a 6-fold vario chassis, two
power supplies are necessary. In this case, redundancy is inapplicable.
The 6-fold vario chassis is not equipped with a fuse on its primary side.
Therefore the protection against excessive currents has to be provided by
the electrical installation of the building.
Pos: 15 /806-IHSE/Beschreibung/Geräteansichte n/481-xx/6-fac h Vario-Gehäuse 474-BODY6B P @ 9\mod_1367827188730_6. doc @ 71694 @ 3 @ 1
6
1
7
2
8
3
5
4
18 2016-02-29
Page 19
Description
3.6.5 6-fold Vario Chassis 474-BODY6BP
CPU and CON Unit
Front View
1 Connect to power supply 1
2 Connect to power supply 2 (redundancy)
3 Grounding
Rear View
1 Slot for modules #5
2 Slot for modules #3
3 Slot for modules #1
4 Slot for modules #6
5 Slot for modules #4
6 Slot for modules #2
Pos: 16 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/6-fac h Vario-Gehäuse 474-BODY6B PF @ 11\mod_1392644763729 _6.doc @ 132650 @ 3 @ 1
123
45
1
2
6
3
2016-02-29 19
Page 20
Draco ultra DisplayPort KVM Extender
3.6.6 6-fold Vario Chassis 474-BODY6BPF
CPU and CON Unit
67
8
Pos: 17 /806-IHSE/zz_Layout/Seitenumbruch @ 8\ mod_1348581820516_0.doc @ 69462 @ @ 1
1
2
Rear View
1 Slot for modules #5
2 Slot for modules #3
3 Slot for modules #1
4 Connect to power supply 1
5 Connect to power supply 2 (redundancy)
6 Slot for modules #6
7 Slot for modules #4
8 Slot for modules #2
3
4 5
20 2016-02-29
Page 21
Description
Pos: 18 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/21-fac h Vario-Gehäuse 474-BODY 21R @ 8\mod_1348579151346_ 6.doc @ 69400 @ 3 @ 1
3.6.7 21-fold Vario Chassis 474-BODY21R
CPU and CON Unit
Pos: 19 /806-IHSE/zz_Layout/Seitenumbruch @ 8\ mod_1348581820516_0.doc @ 69462 @ @ 1
1
Rear View
1 Slots for modules #1 - #21
2
1
Front View
1 Connect to power supply 2
2 Locking for power supply 2 (redundancy)
3 Locking for power supply 1 (standard)
4 Connect to power supply 1
3
4
2016-02-29 21
Page 22
Draco ultra DisplayPort KVM Extender
Pos: 20 /806-IHSE/Beschreibung/Geräteansichte n/490-xx/Typ L- / R490-BPHC @ 15\mod_1455282894 076_6.doc @ 165614 @ 3 @ 1
3.6.8 Model L- / R490-BPHC
CPU Module CON Module
2 341
Rear View Rear View
1 Service port
2 Connect to interconnect cable
3 To CPU: USB-HID
4 To CPU: DisplayPort
Pos: 21 /806-IHSE/Beschreibung/Geräteansichte n/490-xx/Typ L- / R490-BPHS / -BPHX @ 15\mod_1455283 096578_6.doc @ 165647 @ 3 @ 1
1 Service port
2 Connect to interconnect cable
3 Connect to USB-HID devices
4 Connect to DisplayPort monitor
3.6.9 Model L- / R490-BPHS / -BPHX
CPU Module CON Module
Pos: 22 /806-IHSE/zz_Layout/Seitenumbruch @ 8\ mod_1348581820516_0.doc @ 69462 @ @ 1
2 341
Rear View Rear View
1 Service port
2 Connect to interconnect cable
3 To CPU: USB-HID
4 To CPU: DisplayPort
1 Service port
2 Connect to interconnect cable
3 Connect to USB-HID devices
4 Connect to DisplayPort monitor
23 41
23 41
22 2016-02-29
Page 23
Description
Pos: 23 /806-IHSE/Beschreibung/Geräteansichte n/490-xx/Typ L- / R490-BPHCR @ 15\mod_1455283184 105_6.doc @ 165680 @ 3 @ 1
3.6.10 Model L- / R490-BPHCR
CPU Module CON Module
34 521
Rear View Rear View
1 Service port
2 Connect to interconnect cable 1
3 Connect to interconnect cable 2
4 To CPU: USB-HID
5 To CPU: DisplayPort
Pos: 24 /806-IHSE/Beschreibung/Geräteansichte n/490-xx/Typ L- / R490-BPHSR / -BPHXR @ 15\mod_1455283 468708_6.doc @ 165713 @ 3 @ 1
1 Service port
2 Connect to interconnect cable 1
3 Connect to interconnect cable 2
4 Connect to USB-HID devices
5 Connect to DisplayPort monitor
3.6.11 Model L- / R490-BPHSR / -BPHXR
CPU Module CON Module
Pos: 25 /806-IHSE/zz_Layout/Seitenumbruch @ 8\ mod_1348581820516_0.doc @ 69462 @ @ 1
34 521
Rear View Rear View
1 Service port
2 Connect to interconnect cable 1
3 Connect to interconnect cable 2
4 To CPU: USB-HID
5 To CPU: DisplayPort
1 Service port
2 Connect to interconnect cable 1
3 Connect to interconnect cable 2
4 Connect to USB-HID devices
5 Connect to DisplayPort monitor
34 521
34 521
2016-02-29 23
Page 24
Draco ultra DisplayPort KVM Extender
Pos: 26 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/Typ L- / R474-BXH @ 6\mod_13045835076 45_6.doc @ 50984 @ 3 @ 1
3.6.12 Model L- / R474-BXH
CPU Module CON Module
1
Rear View Rear View
1 To CPU: USB-HID 1 Connect to USB-HID devices
Pos: 27 /806-IHSE/Beschreibung/Geräteansichten/ 474-xx/Typ L- / R474-BXE @ 7\mod_1331 798896275_6.doc @ 58110 @ 3 @ 1
3.6.13 Model L- / R474-BXE
CPU Module CON Module
1
Rear View Rear View
1 To CPU: USB 2.0 1 Connect to USB 2.0 devices
Pos: 28 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/Typ L- / R474-BUE @ 7\mod_13317990387 17_6.doc @ 58130 @ 3 @ 1
3.6.14 Model L- / R474-BUE
CPU Module CON Module
1
Rear View Rear View
1 To CPU: USB 2.0 1 Audio IN
When using USB audio within a KVM matrix, instant switching is not
possible due to the deregistration and registration process of the USB.
Pos: 29 /806-IHSE/Beschreibung/Geräteansichten/ 474-xx/Typ L- / R474-BXE2 @ 15\mo d_1455283659481_6.doc @ 165746 @ 3 @ 1
1
1
1
2 3
2 Audio OUT
3 Connect to USB 2.0 devices
24 2016-02-29
Page 25
Description
3.6.15 Model L- / R474-BXE2
CPU Module CON Module
Rear View Rear View
1 To CPU: USB 2.0 1 Connect to USB 2.0 devices
2 Connect to USB 2.0 devices
Pos: 30 /806-IHSE/Beschreibung/Geräteansichten/ 474-xx/Typ L- / R474-BAX / - BSX @ 6\mod_1304583540285_6.doc @ 51002 @ 3 @ 1
3.6.16 Model L- / R474-BAX / -BSX
CPU Module CON Module
1
3
2
Rear View Rear View
1 Connect to serial (D-Sub 9)
2 Audio IN
3 Audio OUT
Pos: 31 /806-IHSE/Beschreibung/Geräteansichten/ 474-xx/Typ L- / R474-BAP @ 9\mod_1362 472648439_6.doc @ 71250 @ 3 @ 1
1 Connect to serial (D-Sub 9)
2 Audio IN
3 Audio OUT
3.6.17 Model L- / R474-BAP
CPU Module CON Module
123
1
3
2
45
123
45
Rear View Rear View
1 Connect to serial (D-Sub 9)
2 Audio IN
3 Audio OUT
4 To CPU: PS/2 mouse
5 To CPU: PS/2 keyboard
Pos: 32 /806-IHSE/Beschreibung/Geräteansichten/ 474-xx/Typ L- / R474-BBX @ 15\mod_144 6714315133_6.doc @ 164690 @ 3 @ 1
1 Connect to serial (D-Sub 9)
2 Audio IN
3 Audio OUT
4 Connect to PS/2 mouse
5 Connect to PS/2 keyboard
2016-02-29 25
Page 26
Draco ultra DisplayPort KVM Extender
3.6.18 Model L- / R474-BBX
CPU Module CON Module
Rear View Rear View
1 Switch for phantom power
2 Audio IN #1
3 Audio IN #2
1 Audio OUT #1
2 Audio OUT #2
3 Not in use
4 Dip switch for pre-amplification
The CPU module with balanced audio can be also used on top of an
extender CON Unit. It depends on the purpose of use.
Pos: 33 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/Typ L- / R474-BDX @ 6\mod_13045835778 01_6.doc @ 51020 @ 3 @ 1
3.6.19 Model L- / R474-BDX
CPU Module CON Module
1
3
2
1
3
2
Rear View Rear View
1 S/PDIF input (RCA)
2 AES/EBU input (Mini-XLR)
3 S/PDIF input (TOSLINK)
Pos: 34 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/Typ L- / R474-BXTC @ 6\mod_13045837845 82_6.doc @ 51110 @ 3 @ 1
1 S/PDIF output (RCA)
2 AES/EBU output (Mini-XLR)
3 S/PDIF output (TOSLINK)
26 2016-02-29
Page 27
Description
3.6.20 Model L- / R474- BXTC and L- / R474-BXUC
CPU Module CON Module
12
3
12
3
Rear View Rear View
1 Service port
2 Connect to interconnect cable
3 To CPU: USB 2.0
Pos: 35 /806-IHSE/Beschreibung/Geräteansichte n/474-xx/Typ L- / R474-BXTS @ 6\mod_1304583818 676_6.doc @ 51128 @ 3 @ 1
1 Service port
2 Connect to interconnect cable
3 Connect to USB 2.0 devices
3.6.21 Model L- / R474- BXTS and L- / R474-BXUS
CPU Module CON Module
Rear View Rear View
1 Service port
2 Connect to interconnect cable
3 To CPU: USB 2.0
Pos: 36 /806-IHSE/Beschreibung/Geräteansichten/ 474-xx/Typ L- / R474-BXEC @ 15\mod _1455283814085_6.doc @ 165779 @ 3 @ 1
12
3
12
1 Service port
2 Connect to interconnect cable
3 Connect to USB 2.0 devices
3
4
4
2016-02-29 27
Page 28
Draco ultra DisplayPort KVM Extender
3.6.22 Model L- / R474- BXEC
CPU Module CON Module
Rear View Rear View
1 Service port
2 Connect to interconnect cable
3 To CPU: USB 2.0
Pos: 37 /806-IHSE/Beschreibung/Geräteansichten/ 474-xx/Typ L- / R474-BXECR @ 15\mod _1455283906953_6.doc @ 165812 @ 3 @ 1
3.6.23 Model L- / R474- BXECR
CPU Module CON Module
Rear View Rear View
1 Service port
2 Connect to interconnect cable 1
3 Connect to interconnect cable 2
4 To CPU: USB 2.0
Pos: 38 /806-IHSE/Beschreibung/Geräteansichten/ 474-xx/Typ L- / R474-BXES @ 15\mod_14 55284047251_6.doc @ 165845 @ 3 @ 1
1 Service port
2 Connect to interconnect cable
3 Connect to USB 2.0 devices
4 Connect to USB 2.0 devices
1 Service port
2 Connect to interconnect cable 1
3 Connect to interconnect cable 2
4 Connect to USB 2.0 devices
5 Connect to USB 2.0 devices
28 2016-02-29
Page 29
Description
3.6.24 Model L- / R474-BXES
CPU Module CON Module
Rear View Rear View
1 Service port
2 Connect to interconnect cable
3 To CPU: USB 2.0
Pos: 39 /806-IHSE/Beschreibung/Geräteansichten/ 474-xx/Typ L- / R474-BXESR @ 15\mo d_1455284111121_6.doc @ 165878 @ 3 @ 1
3.6.25 Model L- / R474- BXESR
CPU Module CON Module
Rear View Rear View
1 Service port
2 Connect to interconnect cable 1
3 Connect to interconnect cable 2
4 To CPU: USB 2.0
Only one USB 2.0 CON module may be installed per chassis.
Pos: 40 /806-IHSE/Beschreibung/Geräteansichte n/483-xx/Typ 474-S NMP @ 13\mod_1412172938631 _6.doc @ 151898 @ 3 @ 1
1 Service port
2 Connect to interconnect cable
3 Connect to USB 2.0 devices
4 Connect to USB 2.0 devices
1 Service port
2 Connect to interconnect cable 1
3 Connect to interconnect cable 2
4 Connect to USB 2.0 devices
5 Connect to USB 2.0 devices
2016-02-29 29
Page 30
Draco ultra DisplayPort KVM Extender
3.6.26 Model 474-SNMP
Control Unit
Pos: 41 /806-IHSE/zz_Layout/Seitenumbruch @ 8\ mod_1348581820516_0.doc @ 69462 @ @ 1
1
2
Rear View
1 Connect to serial (D-Sub 9)
2 Connect to network (RJ45)
The 474-SNMP module can be only used with the chassis 474BODY6BP/F and 474-BODY21 with a production date later than
March 2014.
30 2016-02-29
Page 31
Description
Pos: 42 /806-IHSE/Beschreibung/Diagnose LEDs/ UEB_Diagnose_LEDs @ 6\mod_1304 584004723_6.doc @ 51146 @ 2 @ 1
3.7 Status LEDs
Pos: 43 /806-IHSE/Beschreibung/Diagnose LEDs/490- xx/490-xx Diagnose KV M-Extender-Modul @ 15\ mod_1455285196917_6. doc @ 165912 @ 3 @ 1
3.7.1 Status KVM Extender Module
The KVM Extender module is fitted with a multi color LED on both sides
for overall status indication and with two further LEDs on the back side for
indication of the connection status.
CPU Module CON Module
435621
56
4321
Rear View Rear View
LED 1 and 2: Connection Status Link 1
LED 3 and 4: Connection Status Link 2
Pos. LED Status Description
Failure LED
(green)
Status LED
(green)
Off Connection available 1, 3
On or
Flashing
Connection failure (flashing for about
20 s following a connection failure)
Flashing No connection via interconnect cable 2, 4
On Connection available
LED 5: USB and Video Status Link 1
LED 6: USB and Video Status Link 2
LED color Description
Red
Device ready
Violet
Green /
Connection and USB signal (interconnect) available
Connection and video signal available
light blue
flashing
Light Blue
Connection, USB and video signal available
(operating status)
435621
564321
2016-02-29 31
Page 32
Draco ultra DisplayPort KVM Extender
3.7.2 Status Upgrade Module Digital Audio
The upgrade module digital audio is fitted with a further multi-color LED on
the rear side for indication of the connection status:
CPU Module CON Module
Rear View Rear View
LED 1: Digital Audio Status
LED color Description
Red No signal
Light Blue
Violet
Blue
Green CON Unit: Signal available
Pos: 45 /806-IHSE/Beschreibung/Diagnose LEDs/474- xx/Diagnose Zusatz modul Symmetrisches Au dio @ 15\mod_1446716773 734_6.doc @ 164756 @ 3 @ 1
1
1
Static: CPU Unit: S/PDIF signal (RCA) available
Flashing: CPU Unit: Digital noise
Static: CPU Unit: AES/EBU signal (Mini-XLR)
available
Flashing: CPU Unit: Digital noise
Static: CPU Unit: S/PDIF signal (TOSLINK)
available
Flashing: CPU Unit: Digital noise
32 2016-02-29
Page 33
Description
3.7.3 Status Upgrade Module Balanced Audio
The upgrade module balanced audio is fitted with two LEDs on the rear
side for indication of the connection status:
CPU Module CON Module
Rear View Rear View
Pos. LED Status Description
1, 2 Status LED
Pos: 46 /806-IHSE/Beschreibung/Diagnose LEDs/474- xx/Diagnose Zusatz modul USB-HID @ 6\mod_130458 4220145_6.doc @ 51219 @ 3 @ 1
Green Signal available
Orange Signal level too high
Off No signal
2016-02-29 33
Page 34
Draco ultra DisplayPort KVM Extender
3.7.4 Status Upgrade Module USB-HID
The upgrade module USB-HID is fitted with three further LEDs on the rear
side for indication of the connection status:
CPU Module CON Module
Rear View Rear View
Pos. LED Status Description
1, 2
3
Pos: 47 /806-IHSE/Beschreibung/Diagnose LEDs/474- xx/Diagnose Zusatz modul USB 2.0 embedded @ 7\mod _1331803265129_6.doc @ 58231 @ 3 @ 1
1
23
Device LED
(orange)
Status LED
(orange)
23
1
Off
No USB-HID device or not supported
USB device connected
Flashing
USB-HID device active
fast
On
USB-HID device ready or KVM
Extender in command mode
Off No power supply voltage
CPU Unit: KVM Extender in
command mode or no connection
CON Unit: Keyboard in command
mode
Flashing
slowly
Flashing
CON Unit: KVM Extender in command
mode or no connection
Operating status
fast
34 2016-02-29
Page 35
Description
3.7.5 Status Upgrade module USB 2.0 embedded
The upgrade module USB 2.0 embedded is fitted with three further LEDs
on the rear side for indication of the connection status:
CPU Module CON Module
Rear View Rear View
Pos. LED Status Description
2
3
Pos: 48 /806-IHSE/Beschreibung/Diagnose LEDs/474- xx/Diagnose Zusatz modul USB 2.0 V1 @ 6\mod_13045842 54816_6.doc @ 51237 @ 3 @ 1
1
23
Status LED
(green)
Status LED
(green)
Status LED
(green)
Off No USB 2.0 device connected 1
Flashing
slowly
Off
Flashing
slowly
On
Off
On
23
1
USB 2.0 device connected
No connection to source (computer,
CPU) available
Connection to source (computer,
CPU) available
No USB 2.0 device connected
Connection to source (computer,
CPU) available
USB 2.0 device(s) connected
No connection between CON and CPU
module
Connection between CON and CPU
module available
2016-02-29 35
Page 36
Draco ultra DisplayPort KVM Extender
3.7.6 Status Upgrade Module USB 2.0 V1
The upgrade module USB 2.0 is fitted with a multi color LED on both sides
for overall status indication and with two further LEDs on the back side for
indication of the connection status.
CPU Module CON Module
Rear View Rear View
Pos. LED Status Description
LED 3: USB 2.0 Status
LED color Description
Red
Green
Green /
light blue
flashing
Light blue
Pos: 49 /806-IHSE/Beschreibung/Diagnose LEDs/474- xx/Diagnose Zusatz modul USB 2.0 V2 @ 15\mod_1455286 194876_6.doc @ 16594 5 @ 3 @ 1
12
3
3
12
Failure LED
(green)
Status LED
(green)
12
12
3
3
Off Connection available 1
On or
Flashing
Connection failure (flashing for about
20 s following a connection failure)
Off No connection via interconnect cable 2
On Connection available
Device ready
Only connection available, no USB 2.0 signal
Connection available, no USB 2.0 device
connected
Connection and USB 2.0 signal available
(operating status)
36 2016-02-29
Page 37
Description
3.7.7 Status Upgrade Module USB 2.0 V2
The upgrade module USB 2.0 is fitted with a multi color LED on both sides
for overall status indication and with two further LEDs on the back side for
indication of the connection status.
CPU Module CON Module
Rear View Rear View
Pos. LED Status Description
7
9
Failure LED
(green)
Status LED
(green)
Status LED
(green)
Status LED
(green)
Status LED
(green)
Off Connection available 1, 4
On or
Flashing
Off No connection via interconnect cable 2, 5
On Connection available
Off No USB 2.0 device connected 6
Flashing
slowly
Off
Flashing
slowly
On
Off
On
Connection failure (flashing for about
20 s following a connection failure)
USB 2.0 device connected
No connection to source (computer,
CPU) available
Connection to source (computer,
CPU) available
No USB 2.0 device connected
Connection to source (computer,
CPU) available
USB 2.0 device(s) connected
No connection between CON and CPU
module
Connection between CON and CPU
module available
2016-02-29 37
Page 38
Draco ultra DisplayPort KVM Extender
LED 3: USB 2.0 Status
LED color Description
Red
Violet
Green
Light Blue
Blue
Pos: 50 /806-IHSE/Beschreibung/Diagnose LEDs/483- xx/Diagnose Überwac hungsmodul SNMP @ 13\mod_14 12177197177_6.doc @ 151963 @ 3 @ 1
Device ready, no Matrix connection
Connection to Matrix available
USB 1.1 connection available
USB 2.0 connection available
Debug mode
38 2016-02-29
Page 39
Description
3.7.8 Status Monitoring Module SNMP
The monitoring module SNMP is fitted with a multi color LED on both
sides for overall status indication and with two further LEDs for indication
of the network status:
123 4
Rear View
Status LEDs of the SNMP board
Pos. LED Status Description
Status 1
1
Status 2
4
Due to variations in LED type "white" might also appear as light purple or
light blue.
Status LEDs of the network port
White SNMP board is in registration process
Blue
flashing
Red
Registration of the SNMP board has
started
Registration in progress
flashing
Green
Operating condition
flashing
Green SNMP board de-registered
White SNMP board is in registration process
Status Description
White SNMP board is in registration process
Pos. LED Status Description
Link status
(orange)
Off Port not activated 2
Flashing
Port activated, no connection via
network cable
Link status
(green)
Off Port not activated 3
Flashing
Port activated, no connection via
network cable
Pos: 51 /806-IHSE/Installation/UEB_Installa tion @ 5\mod_1278574971589 _6.doc @ 41768 @ 1 @ 1
2016-02-29 39
Page 40
Draco ultra DisplayPort KVM Extender
4 Installation
Pos: 52 /806-IHSE/Installation/Lieferumfang pr üfen/490-xx @ 15\mod_14 55286954026_6.doc @ 165978 @ 2 @ 1
4.1 Package Contents
Your extender package contains the following items:
KVM Extender:
KVM Extender pair (CPU Unit and CON Unit) in the vario chassis
1x (redundancy 2x) 5VDC international power supply unit per KVM
Extender unit
1x (redundancy 2x) country-specific power cord
Quick Setup
DisplayPort video cable (1.8 m, DisplayPort male-to-male)
USB cable (1.8 m, type A to type B)
Additional content for upgrade module Analog Audio / Serial:
Serial cable (1.8 m, D-Sub 9 male connector)
Stereo jack cable (1.6 m, 3.5 mm male connector)
Additional content for upgrade module Digital Audio:
RCA cable (2.5 m, Cinch male connector)
TOSLINK cable (1.8 m, F05 male connector)
Additional content for upgrade module USB-HID:
USB cable (1.8 m, USB type A to type B)
40 2016-02-29
Page 41
Installation
Additional content for upgrade module PS/2:
2x PS/2 cable (1.8 m, 6-pole connector)
Additional content for upgrade module USB 2.0 embedded:
USB cable (1.8 m, USB type A to type B)
Additional content for upgrade module USB 2.0:
USB cable (1.8 m, USB type A to type B)
If anything is missing, contact your dealer.
Pos: 53 /806-IHSE/Installation/System anschließ en/474-xx @ 6\mod_130 4584542160_6.doc @ 51273 @ 233 @ 1
2016-02-29 41
Page 42
Draco ultra DisplayPort KVM Extender
4.2 System Setup
First time users are recommended to setup the system with the CPU Unit
and the CON Unit in the same room as a test setup. This will allow you to
identify and solve any cabling problems, and experiment with your system
more conveniently.
Please verify that interconnect cables, interfaces, and handling of the
4.2.1 KVM Extender Setup
devices comply with the requirements (see Chapter 7, Page 57).
1. Switch off all devices.
CON Unit Installation
2. Connect your monitor(s), keyboard and mouse to the CON Unit.
3. Connect the CON Unit with the interconnect cable(s).
4. Connect the 5VDC power supply to the CON Unit.
CPU Unit Installation
5. Connect the source (computer, CPU) to the CPU Unit with the
supplied cables. Please ensure the cables are not strained.
6. Connect the CPU Unit to the interconnect cable(s).
7. Connect the 5VDC power supply to the CPU Unit.
8. Power up the system.
To power up the system, the following sequence is recommended:
Monitor – CON Unit – CPU Unit – source.
The basic module with VGA / DVI-I input is connected as above. For a
complete and detailed description of the setup and configuration of the
VGA option, see the manual of the Media- / DVI-Converter K238-5V
(Download
).
42 2016-02-29
Loading...