Page 1
IHSE GmbH
Maybachstrasse 11
88094 Oberteuringen
Germany
[email protected]
www.ihse.de
Tel. +49 7546-9248-0
Fax +49 7546-9248-48
User Manual
Edition: 2011-10-11
Draco major
Model:
K474-UX / CX
Page 2
Draco major
2 2011-10-11
Copyright
© 2011. All rights reserved. This information may not be reproduced in any
manner without the prior written consent of the manufacturer.
Information in this document is subject to change without notice.
Trademarks
All trademark and trade names mentioned in this document are
acknowledged to be the property of their respective owners.
Disclaimer
While every precaution has been taken during preparation of this manual,
the manufacturer assumes no liability for errors or omissions. Neither does
the manufacturer assume any liability for damages resulting from the use
of the information contained herein.
The manufacturer reserves the right to change specifications, functions, or
circuitry of the product without notice.
The manufacturer cannot accept liability for damage due to misuse of the
product or due to any other circumstances outside the manufacturer’s
control (whether environmental or installation related). The manufacturer
shall not be liable for any loss, damage, or injury arising directly, indirectly,
incidentally, or consequently from the use of this product.
Page 3
Contents
2011-10-11 3
Contents
1 About This Manual....................................................................... 7
1.1 Scope.................................................................................. 7
1.2 Validity ................................................................................ 7
1.3 Cautions and Notes ............................................................ 7
1.1 Spellings ............................................................................. 7
2 Safety Instructions....................................................................... 8
3 Description ................................................................................... 9
3.1 Application .......................................................................... 9
3.2 Access Possibilities............................................................. 9
3.3 System Overview .............................................................. 10
3.4 Product Range .................................................................. 11
3.5 Accessories....................................................................... 11
3.6 Device Views .................................................................... 12
3.6.1 Configuration Redundancy.................................. 12
3.6.2 Configuration Standard 1 .................................... 13
3.6.3 Configuration Standard 2 .................................... 14
3.7 Diagnostics and Status ..................................................... 15
3.7.1 Status LEDs........................................................ 15
3.7.2 Status of Console Ports ...................................... 17
3.7.3 Status of the CPU Ports...................................... 21
3.7.4 Network Status.................................................... 24
3.7.5 Firmware Status.................................................. 26
3.8 Trace Function .................................................................. 27
3.9 Flash Memory Status ........................................................ 29
4 Installation .................................................................................. 30
4.1 Package Contents............................................................. 30
4.2 System Setup.................................................................... 31
4.3 Example Applications........................................................ 32
4.3.1 Single-Head Matrix (KVM) .................................. 33
4.3.2 Dual-Head Matrix (KVM)..................................... 34
Page 4
Draco major
4 2011-10-11
4.3.3 Quad-Head Matrix (KVM).................................... 35
4.3.4 Single-Head Matrix (KVM / USB 2.0) .................. 36
4.3.5 Triple-Head-Matrix (KVM / USB 2.0)................... 38
4.3.6 Training System 15............................................. 40
4.3.7 Training System 30............................................. 42
4.3.8 Crosspoint Matrix ................................................ 44
4.3.9 Parallel Operation (Stacking) .............................. 46
4.3.10 Cascading........................................................... 48
5 Configuration.............................................................................. 49
5.1 Command Mode ............................................................... 49
5.2 Control of the Draco major ................................................ 51
5.2.1 Control via OSD .................................................. 51
5.2.2 Control via Java Tool .......................................... 55
5.2.3 Control via LCD Display ...................................... 62
5.2.4 Control via Serial Interface.................................. 66
5.3 System Settings ................................................................ 67
5.3.1 System................................................................ 67
5.3.2 Access ................................................................ 71
5.3.3 Switch ................................................................. 74
5.3.4 Network............................................................... 79
5.3.5 Date and Time .................................................... 82
5.4 User Settings .................................................................... 84
5.4.1 User Properties ................................................... 84
5.4.2 User Matrix.......................................................... 87
5.5 Console Settings............................................................... 89
5.5.1 Console Ports (CON Ports)................................. 89
5.5.2 Console Matrix (CON Matrix) .............................. 93
5.5.3 Mouse and Keyboard .......................................... 95
5.5.4 Touch Screen...................................................... 98
5.5.5 Macro Keys....................................................... 100
5.5.6 Multicast (Follow Me) ........................................ 103
Page 5
Contents
2011-10-11 5
5.6 CPU Settings .................................................................. 106
5.6.1 CPU Ports ......................................................... 106
5.7 Saving and Loading of Configurations ............................ 109
5.7.1 Saving of Configurations in the Matrix .............. 109
5.7.2 Saving of Configurations in a File ..................... 110
5.7.3 Loading of Configurations ................................. 113
5.7.4 Saving and Loading of Configurations
from FTP........................................................... 116
5.8 Firmware Update ............................................................ 118
6 Operation .................................................................................. 120
6.1 Operation by 'Hot Keys'................................................... 120
6.1.1 Direct Switching ................................................ 120
6.1.2 Scan Mode........................................................ 121
6.1.3 Addressing of Main and Sub Matrix .................. 122
6.1.4 Macro Keyboard................................................ 123
6.1.5 Function Keys <F1>–<F12>.............................. 123
6.2 KVM Mode ...................................................................... 124
6.2.1 KVM-List ........................................................... 124
6.2.2 KVM-Switch Function........................................ 126
6.2.3 Follow Me Function (Multicast) ......................... 129
6.3 Crosspoint Mode............................................................. 132
6.3.1 Crosspoint Switch Function (CON Ports).......... 132
6.3.2 Crosspoint Switch Function (CPU Ports) .......... 136
6.4 Serial Interface................................................................ 139
6.5 Power On and Power Down Functions ........................... 140
6.5.1 Restart .............................................................. 140
6.5.2 Reset ................................................................ 141
6.5.3 Power Down...................................................... 141
7 Specifications........................................................................... 142
7.1 Interfaces ........................................................................ 142
7.1.1 RJ45 (Interconnect) .......................................... 142
7.1.2 Fiber SFP Type LC (Interconnect) .................... 142
Page 6
Draco major
6 2011-10-11
7.1.3 RJ45 (Network)................................................. 142
7.1.4 RS-232 (Serial) ................................................. 142
7.2 Interconnect Cable.......................................................... 143
7.2.1 Cat X ................................................................. 143
7.2.2 Fiber.................................................................. 144
7.3 Supported Peripherals .................................................... 146
7.3.1 KVM Extender................................................... 146
7.4 Serial Control .................................................................. 152
7.4.1 Telegram Structure ........................................... 152
7.4.2 Telegrams, Switching Functions ....................... 154
7.5 Connector Pinouts .......................................................... 156
7.6 Power Supply.................................................................. 157
7.7 Environmental Conditions ............................................... 157
7.8 Size................................................................................. 157
7.9 Shipping Weight.............................................................. 157
8 Troubleshooting....................................................................... 158
8.1 External Failure............................................................... 158
8.2 Failure at the Matrix ........................................................ 158
8.3 Blank Screen................................................................... 159
8.4 Video Interference........................................................... 160
9 Technical Support....................................................................161
9.1 Support Checklist............................................................ 161
9.2 Shipping Checklist .......................................................... 161
10 Regulatory and Standards Compliance ................................. 162
10.1 CE Declaration of Conformity.......................................... 162
10.2 North American Regulatory Compliance......................... 163
10.3 WEEE ............................................................................. 163
10.4 RoHS .............................................................................. 163
11 Glossary.................................................................................... 164
11.1 Matrix specific Glossary .................................................. 166
Pos: 1 /806-IHSE/Zu diesem Handbuch/ATB_Zu di esem Handbuch @ 5\mod_1278 573163276_6.doc @ 41510 @ 1222 @ 1
Page 7
About This Manual
2011-10-11 7
1 About This Manual
1.1 Scope
This manual describes how to install your Draco major, how to operate it
and how to perform trouble shooting.
1.2 Validity
This manual is valid for all devices listed on the front page. The product
code is printed on the base of the devices.
1.3 Cautions and Notes
The following symbols are used in this manual:
This symbol indicates an important operating instruction that should be
followed to avoid any potential damage to hardware or property, loss of
data, or personal injury.
This symbol indicates important information to help you make the best use
of this product.
=== Ende der Liste für Textmarke Inhalt ===
1.1 Spellings
You can find the following spellings in the manual:
Spelling Description
<key> Description of a key on the keyboard
<key> + <key> Press keys simultaneously
<key>, <key> Press keys successively
2x <key>
Press key 2x in quick succession
(cf. mouse double click)
Menu item
Description of a menu item in the software
Menu item > Menu item
Select menu items successively
Bold print Description of terms that are used in the
device software
Page 8
Draco major
8 2011-10-11
2 Safety Instructions
To ensure reliable and safe long-term operation of your Draco major
please note the following guidelines:
Installation
Only use the device according to this User Manual. Otherwise the
provided safety can be affected.
Only use in dry, indoor environments.
The Draco major and the power supply units can get warm. Do not
situate them in an enclosed space without any airflow.
Do not place the power supply directly on top of the device.
Do not obscure ventilation holes.
Only use power supplies originally supplied with the product or
manufacturer-approved replacements. Do not use a power supply if it
appears to be defective or has a damaged chassis.
Connect all power supplies to grounded outlets. In each case, ensure
that the ground connection is maintained from the outlet socket
through to the power supply's AC power input.
Do not connect the link interface to any other equipment, particularly
network or telecommunications equipment.
Only connect devices to the serial interface that are sufficiently
secured against short circuit currents and false voltages at the serial
interface.
Take any required ESD precautions.
Repair
Do not attempt to open or repair a power supply unit.
Do not attempt to open or repair the Draco major. There are no user
serviceable parts inside.
Please contact your dealer or manufacturer if there is a fault.
Page 9
Safety Instructions
2011-10-11 9
3 Description
3.1 Application
The Draco major matrix is used to switch from consoles (monitor,
keyboard, mouse, and other peripheral devices) to various sources
(computer, CPU) for establishing a connection.
In a maximum configuration, up to 16 independent consoles can be
switched with up to 32 independent sources.
The Draco major matrix is only specified for the use with extenders that
are able to transmit video, KVM and USB 2.0 signals.
The connection between the matrix and the KVM extenders can only be
made by Cat X or fiber cables.
The matrix serves as a repeater. Thus the matrix can be run in a
maximum distance of 10 km away from the consoles and 10 km away
from the sources.
3.2 Access Possibilities
You have the following possibilities to access the Draco major for
configuration and operation:
Access Option Symbol
OSD
Java tool
LCD display
Serial interface
Page 10
Draco major
10 2011-10-11
3.3 System Overview
A Draco major matrix system consists of a Draco major matrix and one or
more CPU and CON units. The Draco major matrix is connected to the
CPU and CON units by interconnect cables.
The CPU units are connected directly to the source (computer, CPU) by
the provided cables.
Monitor(s), keyboard and mouse are connected to the CON units.
The communication between the Draco major matrix and the CPU and
CON units takes place over the respective interconnect cables.
1
2 3
5
3
6
4
System Overview (exemplary)
1 Source (computer, CPU)
2 CPU Units
3 Interconnect cable
4 Draco major matrix
5 CON Units
6 Console (monitor, keyboard, mouse)
See Chapter 4.3, Page 32 for installation examples.
Page 11
Safety Instructions
2011-10-11 11
3.4 Product Range
Part No. Description
K474-U8/C8 Draco major matrix for 8 users and 8 CPUs
K474-U8/C16
Draco major matrix for 8 users and 16 CPUs
K474-U8/C24
Draco major matrix for 8 users and 24 CPUs
K474-U8/C32
Draco major matrix for 8 users and 32 CPUs
K474-U16/C8 Draco major matrix for 16 users and 8 CPUs
K474-U16/C16 Draco major matrix for 16 users and 16 CPUs
K474-U16/C24 Draco major matrix for 16 users and 24 CPUs
K474-U16/C32 Draco major matrix for 16 users and 32 CPUs
K474-UX/CX
Draco major matrix empty (consisting of a basic
chassis, a basic circuit board, a control board and a
plug-in power supply unit for free configuration)
3.5 Accessories
Part No. Description
474-PSU
Plug-in power supply unit as a replacement or for an
upgrade to a redundant power supply
474-OSD Draco major OSD card
474-DIS Draco major display card
474-C8 Draco major Cat X I/O card
474-M8 Draco major fiber I/O card, Multi-mode
474-S8 Draco major fiber I/O card, Single-mode
474-X8 Draco major I/O card empty, for free configuration
459-1M Multi-mode GBIC for the use in 474-X8
459-1S Single-mode GBIC for the use in 474-X8
474-KEY 16 key macro keyboard
You can find appropriate extenders or other components in Chapter 7.3,
Page 146.
Page 12
Draco major
12 2011-10-11
3.6 Device Views
3.6.1 Configuration Redundancy
123 56874
Rear View
1 I/O module CPU (Cat X)
2 I/O module CPU (fiber)
3 I/O module console (Cat X)
4 I/O module console (fiber)
5 Connect to network (RJ45)
6 Connect to serial interface (D-sub 9-pole)
7 Connect to power supply unit 2 (redundancy)
8 Connect to power supply 1 (standard)
12 3
Front View
1 LCD display
2 Plug-in power supply unit 1 (standard)
3 Plug-in power supply unit 2 (redundancy)
Page 13
Safety Instructions
2011-10-11 13
3.6.2 Configuration Standard 1
123 5674
Rear View
1 I/O module CPU (Cat X)
2 I/O module CPU (fiber)
3 I/O module console (Cat X)
4 I/O module console (fiber)
5 Connect to network (RJ45)
6 Connect to serial interface (D-sub 9-pole)
7 Connect to power supply
12
Front View
1 LCD display
2 Plug-in power supply unit
Page 14
Draco major
14 2011-10-11
3.6.3 Configuration Standard 2
123 6784 5
Rear View
1 I/O module CPU (Cat X)
2 I/O module CPU (fiber)
3 I/O module console (Cat X)
4 I/O module console (fiber)
5 LCD display
6 Connect to network (RJ45)
7 Connect to serial interface (D-sub 9-pole)
8 Connect to power supply
1
Front View
1 Plug-in power supply unit
Page 15
Safety Instructions
2011-10-11 15
3.7 Diagnostics and Status
3.7.1 Status LEDs
The Draco major is fitted with the following LEDs for overall status
indication on every I/O module:
I/O card Cat X
2 1
Rear View
1 Status LED left port
2 Status LED right port
Pos. LED Status Description
Off Port offline
Flashing
Port online, no connection via Cat X
cable
Link Status
(green)
On
Connection via Cat X cable ok,
data traffic active.
Off Port offline
1,2
Link Status
(orange)
Flashing
Port online, no connection via Cat X
cable.
Page 16
Draco major
16 2011-10-11
I/O card fiber
31 24
Rear View
1 Failure LED left port
2 Status LED left port
3 Status LED right port
4 Failure LED right port
Pos. LED Status Description
Off Port offline 1,4
Failure
Status
(red)
Flashing Port online, SFP module failure signal
Off Port offline
On Port online, signal ok
2,3
Link Status
(green)
Flashing Port online, no signal
Page 17
Safety Instructions
2011-10-11 17
3.7.2 Status of Console Ports
All of the connections between the various consoles and CPUs are shown
in this menu.
You have the following possibilities to access the menu:
OSD
1. Select Status > CON Ports in the main menu.
Menu Status – CON Ports
2. Press key <F1> to get to the view CPU Ports.
Page 18
Draco major
18 2011-10-11
The following information is shown in this menu:
Field Description
Black: Number of the CON port
Green: Name of the CON port
K/M: Number of the CPU port with
keyboard and mouse connection
MON: Numbers of the CPU ports with
video connection
Java Tool
Select Status > CON Ports in the task area.
Menu View Status > CON Ports
In this view, video only connections are displayed in orange. Connections
with keyboard and mouse are displayed in red. Finally, full KVM
connections are displayed in green.
Page 19
Safety Instructions
2011-10-11 19
You can select between the following buttons:
Button Function
Reload
Reload status of the CON ports
LCD Display
Select Status > Ports in the main menu.
Output Input
CPU_01 CON_01
CPU_02 n.c.
CPU_03 n.c.
CPU_04 n.c.
CPU_05 n.c.
CPU_06 n.c.
CPU_07 n.c.
CPU_08 n.c.
Status Ports
Draco major
Menu Status – Ports (Video)
The menu consists of six pages. The first four pages inform about the set
video connections, the last two pages inform about the set mouse and
keyboard connections.
To open the next page, press the key <Page Down>.
To open the previous page, press the key <Page Up>.
The following information is shown in this menu:
Field Description
Output
Name of CPU port
Input
Name of CON ports connected to the output
signal (Video) of the CPU port.
Page 20
Draco major
20 2011-10-11
Output Input
CON_01 CPU_01
CON_02 n.c.
CON_03 n.c.
CON_04 n.c.
CON_05 n.c.
CON_06 n.c.
CON_07 n.c.
CON_08 n.c.
Status Ports
Draco major
Menu Status – Ports (mouse / keyboard)
The following information is shown in this menu:
Field Description
Output
Name of CON port
Input
Name of CPU port connected to the output signal
(K/M) of the CON port.
Page 21
Safety Instructions
2011-10-11 21
3.7.3 Status of the CPU Ports
All of the connections between the various consoles and CPUs are shown
in this menu.
You have the following possibilities to access the menu:
OSD
1. Select Status > CON Ports in the main menu.
2. Press the key <F1> to switch to CPU Ports.
Menu Status – CPU Ports
Page 22
Draco major
22 2011-10-11
The following information is shown in this menu:
Field Description
Black: Number of the CPU port
Green: Name of the CPU port
K/M: Number of the CON port with
keyboard/mouse connection
MON: Number of the CON port with
video connection
Java Tool
Select Status > CPU Ports in the task area.
Menu Status – CPU Ports
In this view, video only connections are displayed in orange. Connections
with keyboard and mouse are displayed in red. Finally, KVM connections
are displayed in green.
Page 23
Safety Instructions
2011-10-11 23
LCD Display
Select Status > Ports in the main menu.
Output Input
CPU_01 CON_01
CPU_02 n.c.
CPU_03 n.c.
CPU_04 n.c.
CPU_05 n.c.
CPU_06 n.c.
CPU_07 n.c.
CPU_08 n.c.
Status Ports
Draco major
Menu Status – Ports (Video)
The menu consists of six pages. The first four pages inform about the set
video connections, the last two pages inform about the set mouse and
keyboard connections.
To open the next page, press the key <Page Down>.
To open the previous page, press the key <Page Up>.
The following information is shown in this menu:
Field Description
Output
Name of CPU port
Input
Name of CON ports connected to the output
signal (Video) of the CPU port.
Output Input
CON_01 CPU_01
CON_02 n.c.
CON_03 n.c.
CON_04 n.c.
CON_05 n.c.
CON_06 n.c.
CON_07 n.c.
CON_08 n.c.
Status Ports
Draco major
Menu Status – Ports (mouse / keyboard)
Page 24
Draco major
24 2011-10-11
The following information is shown in this menu:
Field Description
Output
Name of CON port
Input
Name of CPU port connected to the output signal
(KM) of the CON port.
3.7.4 Network Status
The current network configuration is shown in this menu.
You have the following possibilities to access the menu:
The following information is shown in this menu:
Field Description
DHCP
Display that shows, if the network settings are set
dynamically (YES or NO).
IP Address
Display of the IP address as entered manually or
set by DHCP
Subnet Mask
Display of the subnet mask as entered manually or
set by DHCP
Gateway
Display of the gateway address as entered
manually or set by DHCP
MAC ID
Display of the MAC address of the matrix
Errors
Number of data packets with errors
Dropped
Number of dropped data packets
Station
Number of data packets for single receivers
Broadcast
Number of data packets for all receivers
Bytes
Number of received/transmitted bytes
Page 25
Safety Instructions
2011-10-11 25
OSD
Select Status > Network in the main menu.
Menu Status – Network
LCD Display
Select Status > Network in the main menu.
DHCP : YES
IP adress : 0.0.0.0
Subnet mask: 255.255.255.0
Gateway : 0.0.0.0
MAC ID : 00:21:5F:01:00:AE
RX TX
Errors : 0 0
Dropped : 0 0
Station : 0 6
Broadcast : 0 0
Bytes : 0 2064
Status Network
Draco major
Menu Status – Network
Page 26
Draco major
26 2011-10-11
3.7.5 Firmware Status
The firmware version of the built-in modules is shown in this menu.
You have the following possibilities to access the menu:
The following information is shown in this menu:
Field Description
Slot
Assignment of single modules by a slot number
Type
Type of module
Firmware
Name of the firmware of a module including
appropriate release date
OSD
Select Status > Firmware in the main menu.
Menu Status – Network
Page 27
Safety Instructions
2011-10-11 27
Java Tool
Select Status > Firmware in the task area.
Menu Status – Firmware
3.8 Trace Function
All of the activities and switching operations of the Draco major are logged
and recorded in this menu.
This function will be used for diagnostic purposes, if there are problems
with the matrix.
You have the following possibility to access the menu:
OSD
Select Status > Trace in the main menu.
Page 28
Draco major
28 2011-10-11
Menu Status – Trace
The following information is shown in this menu:
Field Description
Time
Time specification for the execution of an activity
or a switching operation
Message
Accurate documentation of the execution of an
activity or a switching operation
Page 29
Safety Instructions
2011-10-11 29
3.9 Flash Memory Status
The name and size of the configuration files are shown in this menu.
You have the following possibility to access the menu:
LCD
Select Status > Flash in the main menu.
Filename Size
config.sys 31284 *
default.sys 31284
config01.sys 31284
config02.sys 31284
config03.sys 31284
config04.sys 31284
config05.sys 31284
config06.sys 31284
Status Flash
Draco major
Menu Status – Flash (Page 1)
Filename Size
config07.sys 31284
config08.sys 31284
modul.sys 528 *
dmTools.jar 420492
Status Flash
Draco major
Menu Status – Flash (Page 2)
An asterisk at the end of a line shows a system file that cannot be
changed. All of the other files can be loaded, saved or deleted by FTP
(see Chapter 5.7.4, Page 116).
Page 30
Draco major
30 2011-10-11
4 Installation
4.1 Package Contents
Your extender package contains the following items:
Draco major matrix
1x power cord per built-in power supply unit
1x serial control cable
1x infrared remote control
2x 19" rack mount
User Manual
Java tool
If anything is missing, contact your dealer.
Page 31
Safety Instructions
2011-10-11 31
4.2 System Setup
First time users are recommended to setup the system in the same room
as a test setup. This will allow you to identify and solve any cabling
problems, and experiment with your system more conveniently.
Optimal results can be achieved by the use of identical mice, keyboards
and monitors. This makes a contribution to a smooth and fast switching
without any delay.
1. Switch off all devices.
2. Connect the monitor(s), keyboard and mouse to the CON unit of the
extender. Connect the source (computer, CPU) via provided
connection cables to the CPU unit of the extender. Ensure that the
cables are not strained.
3. Connect the matrix to the extenders via interconnect cables (Cat X or
fiber). Ensure that for the connection with fiber I/O modules all
required ports are equipped with GBICs.
Please assure that your interconnect cables correspond to the
specifications (see Chapter 7.2, Page 143).
4. Connect the 5VDC power supply units to the extenders.
5. If you have a dual access system, please connect the monitor for the
local console with the appropriate female connector at the CPU unit.
To connect a local (USB) keyboard or mouse, please use free USB
ports on your source (computer, CPU) or use a USB hub between
CPU and CPU unit.
6. Power up the system.
7. Log in at the console as administrator (see Chapter 5, Page 49).
8. Confi
gure your system.
Reconfiguration of a CPU or CON Port between DVI/KVM and USB 2.0
function needs a saving of the new configuration and a restart of the
Draco major (see Chapter 6.5.2, Page 141).
Page 32
Draco major
32 2011-10-11
4.3 Example Applications
The Draco major Matrix offers a completely flexible configuration of your
Matrix environment:
A part of the Draco major can be configured as a Single-Head work
station, another part as a Dual-Head or Quad-Head work station. There
are configurations with KVM and USB 2.0 additionally available.
You can copy your own screen content with the function Follow Me to one
or several monitors, e.g. to a projector for training or presentation
purposes.
In addition to that, you can use the Matrix in every operation mode with
the function Crosspoint Switch.
This function can be used for example to do
the total
or a special
switching operation(s) from a central place that is not possible in standard
operation modes.
In addition to the access by OSD and with a connected keyboard, the
following additional access methods are available:
By the built-in display and the provided infrared remote control
By the Java tool
By the serial interface
A connection to standard media controls is possible.
The following pages show typical and exemplary installations of the Draco
major:
Page 33
Safety Instructions
2011-10-11 33
4.3.1 Single-Head Matrix (KVM)
Up to 16 users can have access to up to 32 CPUs in the Single-Head
operation mode. Though a non-blocking access is given for all users that
means no user can be disturbed by any activity from another user.
1
2 3
5
3
6
4
Single-Head Matrix (KVM)
1 Source (computer, CPU)
2 CPU Unit
3 Interconnect cable
4 Draco major matrix
5 CON Unit
6 Console (monitor, keyboard, and mouse)
If you have a Single-Head console, you can also get access to Dual-Head
or Quad-Head CPUs. However, control will only be given at monitor one.
Page 34
Draco major
34 2011-10-11
4.3.2 Dual-Head Matrix (KVM)
Up to 8 users can have access to up to 16 CPUs in the Dual-Head
operation mode. Though a non-blocking access is given for all users that
means not user can be disturbed by any activity from another user.
1
2 3
3
5
6
4
Quad-Head Matrix (KVM)
1 Dual-Head source (computer, CPU)
2 CPU Unit
3 Interconnect cable
4 Draco major matrix
5 CON Unit
6 Console (2x monitor, keyboard, and mouse)
If you have a Dual-Head console, you can also get access to a SingleHead or Quad-Head CPU. However, the second monitor will remain black,
if you have a Single-Head CPU and if you have a Quad-Head CPU,
control will only be given at monitor one and two.
Page 35
Safety Instructions
2011-10-11 35
4.3.3 Quad-Head Matrix (KVM)
Up to 4 users can have access to up to 8 CPUs in the Dual-Head
operation mode. Though a non-blocking access is given for all users that
means not user can be disturbed by any activity from another user.
1
2 3
3
5
6
4
Quad-Head Matrix (KVM)
1 Quad-Head source (computer, CPU)
2 CPU Unit
3 Interconnect cable
4 Draco major matrix
5 CON Unit
6 Console (4x monitor, keyboard, and mouse)
If you have a Quad-Head console, you can also get access to a SingleHead or Dual-Head CPU.
However, the second, third and fourth monitor will remain dark, if you have
a Single-Head CPU and if you have a Dual-Head CPU, the third and
fourth monitor will stay dark.
Page 36
Draco major
36 2011-10-11
4.3.4 Single-Head Matrix (KVM / USB 2.0)
Up to 8 users with an USB 2.0 link (for USB 2.0 devices such as memory
sticks, printers additionally to keyboard and mouse) can have access to up
to 16 CPUs in the Single-Head KVM/USB operation mode.
Up to 4 USB 2.0 peripheral devices can be connected directly to the CON
unit; more devices can be connected by a standard USB 2.0 hub.
Though a non-blocking access is given for all users that means no user
can be disturbed by any activity from another user.
Single-Head-Matrix (KVM / USB-2.0)
1 Source (computer, CPU)
2 CPU Unit
3 Interconnect cable
4 Draco major matrix
5 CON Unit
6 Console (monitor, keyboard, and mouse)
7 USB 2.0 device
Page 37
Safety Instructions
2011-10-11 37
If you have a Single-Head KVM/USB 2.0 console, you can also get access
to a Triple-Head KVM/USB 2.0 CPU. However, if you have a Single-Head
CPU, the second monitor will remain black and if you have a Quad-Head
CPU, control will only be given at monitor one and two.
However, control will only be given at monitor one. You cannot use the
USB periphery if you try to get access to CPUs without USB 2.0
connection.
Page 38
Draco major
38 2011-10-11
4.3.5 Triple-Head-Matrix (KVM / USB 2.0)
Up to 4 users with an USB 2.0 link (for USB 2.0 devices such as memory
sticks, printers additionally to keyboard and mouse) can have access to up
to 16 CPUs in the Triple-Head KVM/USB operation mode.
Up to 4 USB 2.0 peripheral devices can be connected directly to the CON
unit; more devices can be connected by a normal USB 2.0 hub.
Though a non-blocking access is given for all users that means no user
can be disturbed by any activity from another user.
Triple-Head-Matrix (KVM / USB 2.0)
1 Triple-Head source (computer, CPU)
2 CPU Unit
3 Interconnect cable
4 Draco major matrix
5 CON Unit
6 Console (3x monitor, keyboard, and mouse)
7 USB 2.0 device
Page 39
Safety Instructions
2011-10-11 39
If you have a Triple-Head KVM/USB 2.0 console, you can also get access
to a Single-Head KVM/USB 2.0 CPU. However, the second and third
monitor will remain black.
You cannot use the USB periphery if you try to get access to CPUs
without USB 2.0 connection.
Page 40
Draco major
40 2011-10-11
4.3.6 Training System 15
You can have a flexible access for up to 15 students if you use the
'Training System 15' operation mode. All of the work stations of the
students and of the teacher are connected to the Draco major matrix with
a interconnect cable.
The following functions are possible:
The teacher can get the screen content of every single student and
can take control, if necessary.
The screen content of the teacher can be shown to one, several or all
of the student work stations.
The screen content of every single student can be shown to one,
several or all of the student work stations.
Training System 15
A Students' area
B Teacher's area
Page 41
Safety Instructions
2011-10-11 41
1 Source (computer, CPU)
2 Console (monitor, keyboard, mouse)
3 CPU Unit
4 CON Unit
5 Interconnect cable
6 Draco major matrix
7 Projector (as an option)
The CPU that should be displayed on the respective monitor can be
selected by the OSD or by a macro keyboard with control keys.
If you use the Follow Me function, the screen content of the teacher can
be duplicated to one or more additional monitors (e.g. to a projector) – in
this case, the number of available students will be reduced.
Page 42
Draco major
42 2011-10-11
4.3.7 Training System 30
If you want to use the Draco major matrix with the 'Training System 30'
operation mode, the access is slightly limited, but still comfortable.
The following functions are possible:
The teacher can receive the screen content of every single student,
but he cannot take over control.
The screen content of the teacher can be displayed on an additional
monitor (e.g. a projector).
The screen content of every single student can be displayed on an
additional monitor (e.g. a projector).
Training System 30
A Students' area
B Teacher's area
1 Student's work station (source console)
2 CPU Unit
3 Interconnect cable
4 Draco major matrix
5 CON Unit
6 Projector (optional)
Page 43
Safety Instructions
2011-10-11 43
The CPU displayed on the teacher's monitor and on an additional monitor
can be selected respectively by the OSD or by a control panel with control
keys at any time.
Page 44
Draco major
44 2011-10-11
4.3.8 Crosspoint Matrix
The use of the 'Crosspoint Switch' function allows a flexible performance
of the switching functions. This operation mode is generally used to switch
up to 32 sources (Computer, CPU) and up to 16 consoles.
Reverse Mode
In 'reverse mode', up to 16 sources (computer, CPU) can be switched to
32 consoles.
The switching can be done in a number of different ways:
By the OSD of a console that is connected to the CON port
By a PC and the Java tool
By switching commands in combination with the network connection
By switching commands in combination with the serial connection
1
2 3
5
3
6
4
Crosspoint Matrix
Page 45
Safety Instructions
2011-10-11 45
1 Source (e.g. computer, DVD player and video camera)
2 CPU Unit
3 Interconnect cable
4 Draco major matrix
5 CON Unit
6 Console (e.g. monitor, keyboard, mouse and projector)
Any signal source can be switched to as many displays as required. On
these displays, video can be shown at the same time. In addition to that,
even (optional) audio signals can be disposed.
Page 46
Draco major
46 2011-10-11
4.3.9 Parallel Operation (Stacking)
If you have special configurations, especially at installations with several
monitors per work station or additional support of USB 2.0 transmission
paths, the number of connectable CPUs and consoles can be increased
by a parallel operation (stacking) of several Draco major matrices.
One of the Draco major matrices has to be defined as the master matrix,
all of the others have to be configured as slave and the IP address of the
master matrix has to be entered in the field Master IP Address (see
Chapter 5.3.1, Page 67).
T
hey have to be connected to the master matrix by the network connector
(RJ45) of the CPU board. The option Enable LAN Echo has to be
activated at the master matrix (see Chapter 5.3.1, Page 67).
Switching of stacked devices might be delayed by several seconds.
1
2 3 4
6
3
7
5
8
Parallel Operation (Stacking)
Page 47
Safety Instructions
2011-10-11 47
1 Dual-Head source (computer, CPU)
2 CPU Unit
3 Interconnect cable
4 Draco major matrix (Master)
5 Draco major matrix (Slave)
6 Network connection Master / Slave(s)
7 CON Unit
8 Console (2x monitor, keyboard and mouse)
Page 48
Draco major
48 2011-10-11
4.3.10 Cascading
For applications exceeding the number of available ports, the system can
be extended by cascading.
In this case, the Draco major devices are connected by so-called "tie
lines". The tie lines are dynamically configured to support connections in
both directions.
To access cascaded matrices from a console, one of the matrices has to
be configured as sub matrix (see Chapter 5.3.1, Page 67).
1
2 3 34
6
3
7
5
Cascading
1 Source (computer, CPU)
2 CPU Unit
3 Interconnect cable
4 Draco major (sub matrix)
5 Draco major (main matrix)
6 CON Unit
7 Console (monitor, keyboard and mouse)
Page 49
Configuration
2011-10-11 49
5 Configuration
5.1 Command Mode
The Draco major has a Command Mode that allows several functions via
keyboard command during normal use.
To enter Command Mode use a 'Hot Key' sequence and to exit Command
Mode, press <Esc>. While in Command Mode, the LEDs Shift and Scroll
on the console keyboard will flash.
In Command Mode normal keyboard and mouse operation will cease.
Only selected keyboard commands are available.
The following table lists the keyboard commands to enter and to exit
Command Mode and to change the 'Hot Key' sequence:
Function Keyboard Command
Enter Command Mode
(default)
2x <Right Shift> (or 'Hot Key')
Exit Command Mode <Esc>
Change 'Hot Key' sequence
<current 'Hot Key'> + <c>,
<new 'Hot Key' code>, <Enter>
Until 2011-30-09:
<Left Ctrl> + <Left Shift> + <c>,
<'Hot Key' Code>, <Enter>
<Key> + <Key> Press keys simultaneously
<Key>, <Key> Press keys successively
2x <Key> Press key quickly, twice in a row
(similar to a mouse double-click)
The 'Hot Key' sequence to enter Command Mode can be changed. The
following table lists the 'Hot Key' Codes for the available key sequences:
'Hot Key' Code 'Hot Key'
1 <Left Ctrl> + <Left Shift> + <i>
2 2x <Scroll>
3 2x <Left Shift>
4 2x <Left Ctrl>
5 2x <Left Alt>
6 2x <Right Shift>
Page 50
Draco major
50 2011-10-11
'Hot Key' Code 'Hot Key'
7 2x <Right Ctrl>
8 2x <Right Alt>
In a KVM matrix configuration, choose different 'Hot Keys' for the
KVM extender and the Draco U-Switch.
Page 51
Configuration
2011-10-11 51
5.2 Control of the Draco major
5.2.1 Control via OSD
Via On-Screen-Display (OSD) you can do all of the settings for the Draco
major operating system from every single console. The settings are
described in the submenu Configuration. All the other submenus are
described in later chapters.
Entering OSD
1. Open Command Mode with the 'Hot Key' (see Chapter 5.1, Page 49).
2. Press <o> to open OSD. The menu KVM-List is opened as a start
menu.
3. Press <Esc> to enter the main menu.
If the option Listview is not active, KVM Switch view will be shown.
Leaving OSD
Press keys <Shift> + <Esc>.
OSD will be closed without any further change and the currently
selected CPU connection will be established.
Page 52
Draco major
52 2011-10-11
General layout of the OSD screen
Example Main Menu
The general layout of the OSD is structured into three areas:
Upper status area (topmost two text lines)
Working area
Lower status area (lowermost two text lines)
Keyboard control in the OSD
You can navigate within the various screens with the following keys and
key combinations:
Function Keyboard Command
Left cursor - only within an input field or a
switching screen
<Cursor Left>
Right Cursor - only within an input field or a
switching screen
<Cursor Right>
In input fields: Line up (with wrap
around)
In menus: Line up (without wrap
around)
<Cursor Up>
Page 53
Configuration
2011-10-11 53
Function Keyboard Command
In input fields: Line down (with wrap
around)
In menus: Line down (without wrap
around)
<Cursor Down>
Previous page in input masks or status
screens with several pages
<Page Up>
Next page in input masks or status
screens with several pages
<Page Down>
Next field in input masks <Tab>
Previous field in input masks <Left Shift> + <Tab>
Next option in selection fields <+>
Previous option in selection fields <->
(On/Off and No/Yes).
Only if Allow Sharing is active: Switching
and data transfer by save function in the
menu KVM-Switch screen
Switching between selection fields in
selection screens with two conditions,
e. g. between On / Off or between
Y (Yes) / N (No)
If Allow Sharing is active: Data is
additionally saved in the menu KVM-
Switch.
<Space>
In menus with input fields: Save data
In menus: Select menu item
<Enter>
In input fields: Cancel data input
without saving
In selection fields: Return to menu
<Esc>
Menu options in the OSD
The following functions are available:
Button Function
All
Selection of all options
None
Deselection of all options
Cancel
Abort data transfer without saving
Save
Data transfer with saving
Page 54
Draco major
54 2011-10-11
All and None have to be confirmed with Save or rejected with Cancel.
Password request in the OSD
You have to login with administrator rights to set configurations.
Menu Login
You have to login with administrator rights to be able to do configuration
settings. By default, a user with administrator rights is predefined:
Login Password
User
admin
Password
admin
(until 2009-10-20: draco)
This user should be supplied with an own password as fast as possible
(see Chapter 5.4.1, Page 84).
Page 55
Configuration
2011-10-11 55
5.2.2 Control via Java Tool
Requirements
If you want to use the Java Tool, the following requirements have to be
fulfilled:
Computer with an executable Java tool and an installed Java Runtime
Environment (JRE)
Available network connection between the computer and the matrix
Appropriate matrix configuration
Available connection between the Java tool and the matrix
Installation of the Java Tool
The Java-Tool is available in the form of a single executable program file
that does not require a separate installation.
Copy the tool after receiving the file to a directory on your computer.
If you do not have a Java tool, contact your dealer.
Computer Connection to the Matrix
For the connection between computer and matrix, a crossed network
cable is required.
Connect the network cable with the appropriate RJ45 connectors of
both devices.
Start of the Java Tool
Open the Java tool by a double click on the program file or use the
key <Enter> of the keyboard.
Connection to the Matrix
1. Open the Java tool.
2. Select Switch > Connect in the menu bar.
Page 56
Draco major
56 2011-10-11
3. Enter the IP address in the appearing input field according to the
network configuration of the Draco major (see Chapter 5.3.4,
Page 79). In addition to that the user name and password according
to the predefined user properties of the Draco major is requested (see
Chapter 5.4.1, Page 84).
4. Confirm your inputs with the button OK or reject with Cancel.
View Connect
Up to eight connections between the matrix and the Java tool can be
established at the same time due to a limitation of available sockets.
Page 57
Configuration
2011-10-11 57
Menu structure
Example View
The menu structure of the Java tool is subdivided into various sections:
Menu bar (top line)
Toolbar (second line)
Tab bar (third line)
Task area (left menu section)
Working area (right menu section)
Operating Instructions
The operation of the Java tool is intuitive and corresponds to the user
interface of common operating systems.
The Java tool contains its own support function.
In the User Manual of the Draco major is only described, how to find and
open the appropriate menus in the Java tool. For further operations use
the Java tool support function.
The integrated help texts in the working area of the Java tool can be
activated or deactivated by the checkbox in the right upper corner.
Page 58
Draco major
58 2011-10-11
Mouse Control
You can select between the following mouse commands:
Function Mouse Command
Select menu, marking Left mouse button
Open function specific
selection field
Double click left mouse button
Open context specific
selection field
Right mouse button
Keyboard Control
You can select between the following keyboard commands:
Function Keyboard Command
Cursor to the left <Cursor Left>
Cursor to the right <Cursor Right>
Line up <Cursor Up>
Line down <Cursor Down>
Previous page in input or status menus
with more than one page
<Page Up>
Next page in input or status menus with
more than one page
<Page Down>
Next field in input menus <Tab>
Previous field in input menus <Left Shift> + <Tab>
Switching in selection fields between two
conditions (checkmark or not). Öpening of
already marked fields with editing or
selecting possibility.
<Space>
Data saving in menus.
Menu item selection – in menus
<Enter>
Exit from tables
Switching from tables into the next
field
<Ctrl> + <Tab>
Exit from tables
Switching from tables into the
previous field
<Ctrl> + <Left Shift> +
<Tab>
Various functions within the menus in the menu bar can be done with the
provided keyboard commands (e. g. press <Ctrl> + <s> to execute Save)
that are listed to the right of the respective menu item.
Page 59
Configuration
2011-10-11 59
Context Function
The Java tool is equipped with several context functions that support a
user friendly and effective operation of the tool. The context functions are
described in the appropriate chapters.
To execute a context function, use the right mouse button on the
corresponding field and select the desired function.
Sorting Function
The lists and tables in the Java tool are equipped with a sorting function
that allows a fast and smooth search inside.
1. To do an ascending sort, use the left mouse button once to click on
the header of the column that has to be sorted. The sort is displayed
by an arrow that points upwards.
2. To do a descending sort, use the left mouse button twice to click on
the header of the column that has to be sorted. The sort is displayed
by an arrow that points downwards.
3. To remove the sort, use the left mouse button once or twice to click
on the header of the column that is sorted until the displayed arrow
will disappear.
Filter Function
The lists and tables in the Java tool are equipped with a filter function that
allows a fast and smooth search inside.
1. To activate a filter, use the right mouse button to click on the header
of the column that has to be filtered and select Set Filter.
2. Write directly the word or part of a word that has to be filtered into the
header. The filter results are shown immediately.
3. To delete a filter, use the right mouse button to click on the header of
the column that has to be filtered and select Clear Filter.
The filter function is based on the functional principle of common web
search engines.
Page 60
Draco major
60 2011-10-11
Configuration in the Java Tool
Configurations and system settings via Java tool can only be done in
offline mode without a direct connection between matrix and Java tool.
To activate a created configuration in the matrix, proceed as follows:
1. Select File > Upload to in the menu bar. Enter the IP address of the
matrix (see Chapter 5.3.4, Page 79) and the name and password of
the user id
entification and select the storage location of the new
configuration (default or config01-08) in the menu Select
Configuration.
2. Select Switch > Connect in the menu bar and enter the IP address of
the matrix and the name and password of the user identification ein.
3. Select Administration > Activate Configuration in the task area
and select the storage location that has been selected in point 1.
4. Use the button Activate to load the selected configuration in the
matrix. The connection and the open tab will be closed and the matrix
will be restarted.
During the activation of a configuration, the matrix is temporarily not
available.
Page 61
Configuration
2011-10-11 61
Configuration File
The Java tool is equipped with an additional configuration file
(defaults.cfg) by default. This file allows the user to set various
configuration parameters of the Java tool.
The file can be opened and edited by standard text editor programs,
The following configuration parameters can be edited:
Parameter Description
IP Default IP address of the matrix required for
connection
user
Default user name required for connection
sys.dir
Default directory for configuration files
upd.dir
Default directory for update files
dfw.dir
Default directory for the firmware status
dmx.dir
Default directory fort he switching matrix
safemode true: safemode activated
false: safemode deactivated
Page 62
Draco major
62 2011-10-11
5.2.3 Control via LCD Display
In normal operation of the LCD displays the 'Home' screen is shown. In
this view you can find various device information:
IHSE GmbH
Maybachstr. 11
88094 Oberteuringen
Germany
Draco major
07.10.10
F02.09
Fon +49 7546 9248 0
Fax +49 7546 9248 48
www.ihse.de
Start Menu
Press the key <Enter> on the infrared remote control to get from the
'Home' screen into the main menu.
Status
Configuration
Task Status
Menu
Draco major
Menu Main Menu
Navigate with the cursor keys and press the key <Enter> (red) to get
to the respective submenus.
Page 63
Configuration
2011-10-11 63
Infrared Remote Control
The LCD display at the Draco major can be controlled by an infrared
remote control.
The following keys are applicable for the use with the LCD display:
Key Description
Open OSD and select menu.
Open OSD and select menu.
Leave current menu and go back to the
previous menu level.
Exit OSD.
Page 64
Draco major
64 2011-10-11
Key Description
Delete contents in the input field.
Switch between two input fields.
Navigate to the beginning or the end of an
input field.
Scroll page by page in multilateral menu
items.
Navigate within the menu level.
Navigate within the input field.
Set parameters directly by the keypad.
Page 65
Configuration
2011-10-11 65
Key Description
Select between different possibilities in the
selection field.
Page 66
Draco major
66 2011-10-11
5.2.4 Control via Serial Interface
The Draco major comes with widespread functions for an operation via
serial interface (see Chapter 7.4, Page 152). There are telegrams for
S
witching single or all connections available, both unidirectional and
bidirectional. In addition to that, there are telegrams for an overall
definition of the total switching status and for saving and loading such
switching states.
The functionality is consistent with the switching in the Crosspoint Mode
of the OSD (see Chapter 6.3, Page 132).
B
y request, the Draco major optionally provides an echo of all effected
switching operations via serial interface or network interface. That is why
you have the possibility to track the actual configurations of the matrix at
any time and so update your own applications.
Page 67
Configuration
2011-10-11 67
5.3 System Settings
5.3.1 System
You can configure the parameters for the system configuration in this
menu.
You have the following possibilities to access the menu:
You can only set a selection of system parameters in the LCD display, in
contrast to the OSD.
You can select between the following settings:
Field Selection Description
Name
Text
Insert a name of the configuration in
which the current settings should have to
be saved (default: Name).
Device
Text
Insert the name of the matrix that is
shown in the lower left corner of all
menus (default: SWITCH_01).
Info
Text
Additional text field for the description of
the configuration (default: Factory
settings).
Y (Yes) Configuration and remote control of the
sub matrix according to the settings of
the main matrix. No local configuration
opportunity available.
Note: If the matrix is defined as a sub
matrix, the user automatically loses
control in the OSD. Control can be
gained again, if you open the OSD of the
defined sub matrix again by using the
'Hot Key' command <Shift>, <Shift>,
<s>, <o>.
Sub Matrix
N (No)
Function not active (default)
Y (Yes) Starting the matrix after restart or a
switch-on with the default configuration.
Load Default
N (No) Start the matrix after a restart or a
switch-on with the last saved
configuration (default).
Page 68
Draco major
68 2011-10-11
Field Selection Description
Y (Yes) Save the current configuration of the
matrix in the flash memory periodically.
Auto Save
N (No)
Function not active (default)
Y (Yes) Send echoes of all switching commands
done by the matrix.
Enable
COM Echo
N (No)
Function not active (default)
Y (Yes) Reject commands via external interfaces
(RJ45, RS232) during OSD is open.
Lock
COM Ports
N (No)
Function not active (default)
Baud rate
kBaud
Numerical
value
Select a predefined Baud rate for the
serial control (default: 115.2 kBaud).
Y (Yes) Synchronize the slave matrix according
to the settings of the master matrix.
Slave Matrix
N (No)
Function not active (default)
Master IP
Address
Numerical
value
Set the network address of the master
matrix (default: 0.0.0.0).
Page 69
Configuration
2011-10-11 69
OSD
Select Configuration > System in the main menu.
Menu Configuration – System
Page 70
Draco major
70 2011-10-11
Java Tool
Select System > System Data in the task area.
Menu System – System Data
LCD Display
Select Configuration > System in the main menu.
Menu Configuration – System
Sub Matrix
Slave Matrix
Page 71
Configuration
2011-10-11 71
5.3.2 Access
You can configure the parameters for the access configuration in this
menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field Selection Description
Y (Yes) The user has to login with an user name
and a password once to enter OSD.
Thereafter the user remains logged in
until he explicitly logs out or an Auto
Logout is done.
Enable Login
N (No)
Function not active (default)
Y (Yes) The user can only switch to CPU ports
that are unlocked for him in the User
Matrix.
KVM switching with 'Hot Key' commands
is only possible if the user is logged in.
User Matrix
N (No)
Function not active (default)
Y (Yes) The user can only switch from his
console to CPU ports that are unlocked
in the menu CON Matrix (see
Chapter 5.5.2, Page 93).
CON Matrix
N (No)
Function not active (default)
Y (Yes) If you open the OSD, the console will be
automatically disconnected from the
current CPU. Only effective with Enable
Login or User Matrix.
Note: Only keyboard/mouse connections
will be disconnected, video connections
will be preserved.
Auto
Disconnect
N (No)
Function not active (default)
Page 72
Draco major
72 2011-10-11
Field Selection Description
OSD Timeout
Seconds
Period of inactivity after OSD will be
closed automatically. If you select 0
seconds, there will be no timeout
(default: 0 seconds).
Note: The timer is inactive during OSD is
open.
Auto Logout
Minutes
Period of inactivity after a user is
automatically logged out from the OSD
at this console (default: 0 minutes).
OSD
Select Configuration > System in the main menu.
Menu Configuration – System
Page 73
Configuration
2011-10-11 73
Java Tool
Select System > Access in the task area.
Menu System – Access
LCD Display
Select Configuration > Access in the main menu.
Enable Login : N
User Matrix : N
CON Matrix : N
Auto Disconnect : N
OSD Timeout [sec]: 0
Auto Logout [min]: 0
Configuration Access
Draco major
Cancel Save
Menu Configuration – Access
Page 74
Draco major
74 2011-10-11
5.3.3 Switch
You can configure the parameters for the matrix configuration in this
menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field Selection Description
Y (Yes) The user can switch the video signal
from any CPU to his monitor (observer).
Keyboard/mouse control is not possible.
Note:
Switching with the key <Space> and not
<Enter>.
The operator will not be informed if
further users connect as an observer to
the CPU that is connected to his
console.
Allow Sharing
N (No)
Function not active (default)
Y (Yes) The User can connect to every single
CPU as an operator, even to such ones
that are related to another user. The
previous user is set to observer status.
Note: To share K/M control Force
Connect has to be activated.
Force
Connect
N (No)
Function not active (default)
Y (Yes) Extension of 'Force Connect': If the user
connects to a CPU as an operator that
is already related to another user, the
connection to the previous user will be
completely disconnected.
Note: To share K/M control Force
Disconnect has to be deactivated.
Force
Disconnect
N (No)
Function not active (default)
Page 75
Configuration
2011-10-11 75
Field Selection Description
Y (Yes) After opening the OSD, the user attains
to the mask KVM List. This list only
contains the CPU ports available at this
console (default).
KVM Listview
N (No) Function not active. After opening the
OSD, the user attains to the extended
switching mask KVM-Switch.
Y (Yes) After switching of the CPU port in the
masks KVM-List or KVM-Switch, OSD
will be automatically left and the
connection to the new CPU will be
displayed (default).
KVM Auto
Close
N (No)
Function not active
Y (Yes) After pressing any key a KVM
connection to the first available CPU will
be established.
Note: The option Auto Connect is only
functional, if there is no active
connection to a CPU yet.
Auto Connect
N (No)
Function not active (default)
CON Timeout
Minutes
Period of inactivity until the connection
of the own console to the connected
CPU will be automatically disconnected
(default: 0 minutes).
Y (Yes) Activate request of keyboard control
between two consoles.
Keyboard
Connect
N (No)
Function not active (default)
Y (Yes) Activate request of mouse control
between two consoles.
Mouse
Connect
N (No)
Function not active (default)
Release Time
Seconds
Period of inactivity of a connected
console until keyboard and mouse
control can be requested for further
consoles that are connected to the
same CPU (default: 10 seconds)
Note: Set value '0' for a delay less
transfer in real-time. Only one console
can have keyboard and mouse control
at the same time. The other consoles
that are connected to the same CPU
have a video only status.
Page 76
Draco major
76 2011-10-11
OSD
Select Configuration > System in the main menu.
Menu Configuration – System
Page 77
Configuration
2011-10-11 77
Java Tool
Select System > Switch in the task area.
Menu System – Switch
LCD Display
Select Configuration > Switch 1 or Configuration > Switch 2 in the
main menu.
Allow Sharing : N
Force Connect : N
Force Disconnect : N
KVM Listview : N
KVM Auto Close : N
Configuration Switch 1
Draco major
Cancel Save
Menu Configuration – Switch 1
Page 78
Draco major
78 2011-10-11
Menu Configuration – Switch 2
Page 79
Configuration
2011-10-11 79
5.3.4 Network
You can configure the network parameters in this menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field Selection Description
Y (Yes) Selection whether network settings are
supplied automatically
DHCP
N (No)
Function not active (default)
IP Address
Byte
Input of the IP address in the form
'192.168.1.1' in combination with an
operation without DHCP
Subnet Mask
Byte
Input of the subnet mask in the form
'255.255.255.0' in combination with an
operation without DHCP
Gateway
Byte
Input of the subnet mask in the form
'192.168.1.1' in combination with an
operation without DHCP.
Only modify the network parameters in consultation with your system
administrator. Otherwise unexpected results and failures can occur in
combination with the network.
Page 80
Draco major
80 2011-10-11
OSD
Select Configuration > Network in the main menu.
Menu Configuration – Network
Page 81
Configuration
2011-10-11 81
Java Tool
Select System > Network in the task area..
Menu System – Network
LCD Display
Select Configuration > Network in the main menu.
Menu Configuration – Network
Page 82
Draco major
82 2011-10-11
5.3.5 Date and Time
You can configure date and time in this menu.
You have the following possibilities to access the menu.
You can select between the following settings:
Field Selection Description
Month
1 -12 Select month
Date
1 – 31 Select date
Year
1 – 99 Select year
Day of the
week
1 – 7 Select day of the week
Hours
0 – 23 Select hour
Minutes
0 – 59 Select minute
Seconds
0 – 59 Select second
The date input should be done accordingly to the English notation with the
prefixed month notation.
Page 83
Configuration
2011-10-11 83
OSD
Select Configuration > Date + Time in the main menu.
Menu Configuration – Date + Time
LCD Display
Select Configuration > Date + Time in the main menu.
Menu Configuration – Date + Time
Page 84
Draco major
84 2011-10-11
5.4 User Settings
5.4.1 User Properties
You can configure the various user properties and add new users in this
menu.
You have the following possibilities to access the menu:
You can select between the following settings:
Field Selection Description
Name
Text User name (case sensitivity)
Password
Text User password (case sensitivity)
Y (Yes) User is allowed to login and access via
HTTP.
HTTP
N (No)
Function not active
Y (Yes) User is allowed to login and access via
FTP.
FTP
N (No)
Function not active
Y (Yes) User is allowed to login and access via
Internet (currently not realized).
PPP
N (No)
Function not active
Y (Yes) User is allowed to login and access via
Telnet.
TEL
N (No)
Function not active
Y (Yes) User is 'Power-User' and is allowed to
open crosspoint mode.
POW
N (No)
Function not active
Y (Yes) User is Administrator and is allowed to
do all configurations and settings at the
matrix.
ADM
N (No)
Function not active
Page 85
Configuration
2011-10-11 85
OSD
Select Configuration > User in the main menu.
Menu Configuration – User
Page 86
Draco major
86 2011-10-11
Java Tool
Select User > User Data in the task area.
Menu User – User Data
You can select between the following buttons:
Button Function
Copy User
Copy marked user to clipboard
Paste User
Paste user from clipboard
Delete User
Delete selected user
Page 87
Configuration
2011-10-11 87
5.4.2 User Matrix
In this menu you can unlock a specific selection of CPU ports for every
single user.
You have the following possibilities to access the menu:
The use of the User Matrix can be activated in the system settings (see
Chapter 5.3.1, Page 67). If the option User Matrix is active, all switching
operations require a logged in user at the console. Also switching by
keyboard 'Hot Keys' needs a prior login
OSD
Select Configuration > User Matrix in the main menu.
Unlocked ports are marked in green; all the other ports are marked in
red.
Menu Configuration – User Matrix
Page 88
Draco major
88 2011-10-11
You can select between the following buttons:
Button
Function
All Selection of all CPUs
None Deselection of all CPUs
Cancel Abort data transfer without saving
Save Data transfer with saving
The options All and None have to be confirmed with Save or rejected with
Cancel.
Java Tool
Select User > User Matrix in the task area.
Menu User – User Matrix
You can select between the following buttons:
Button Function
Copy Matrix Copy User Matrix of the selected user to clipboard
Paste Matrix Paste User Matrix from clipboard
Page 89
Configuration
2011-10-11 89
5.5 Console Settings
5.5.1 Console Ports (CON Ports)
The name, type, OSD view and the currently related CPU port for every
single console are shown and can be configured in this menu.
You have the following possibilities to access the menu:
If you want to configure the console ports, you will have to consider the
following notes for a correct selection of the port types:
Single-Head ports and USB 2.0 ports can be switched individually.
Dual-Head ports, Quad-Head ports and also Single-Head/USB 2.0
ports are always switched together.
Only odd ports (#01, 03, 05, etc.) can be configured as Dual-Head
ports or Single-Head/USB 2.0 ports.
Only every fourth port (#01, 05, 09, etc.) can be configured as Quad-
Head port or Triple-Head/USB 2.0 port.
Respectively, only the first CON port can be still switched by 'Hot
Keys'. The other ports behave like 'slaves'.
If you switch to differently configured CPU ports, one or more
monitors can remain dark.
If a user switches from a Quad-Head console to a Single-Head CPU
port, the other three monitors will remain dark.
If a user switches from a Quad-Head console to a Dual-Head CPU
port, two of the four monitors will remain dark.
If a user switches from a '1U' console to a Single-Head CPU port
followed by a '0U' CPU port, the USB port will remain active
If a user switches from a 1U console to a Single-Head CPU port followed
by a 0U CPU port, the USB port will remain active.
The reconfiguration of a CPU or CON port between DVI/KVM and
USB 2.0 funktionality requires a backup of the new configuration by the
option Save and and can only be activated by a subsequent restart of the
Draco major.
Page 90
Draco major
90 2011-10-11
You can select between the following settings:
Field Selection Function
Name
Text
Name of the console connected to this
port
SH
Single-Head port
DH
Dual-Head port
QH
Quad-Head port
0U
USB-2.0 port
1U
Single-Head port with USB 2.0 port
Type
3U
Triple-Head port with USB 2.0 port
VAR OSD embedded to current resolution
(default)
OSD display screen filling:
800
800x600
1024
1024x768
1280
1280x1024
1600
1600x1200
OSD
1920
1920x1200
CPU Port
number
Number of the CPU that is connected to
this console or will be connected after
saving
Page 91
Configuration
2011-10-11 91
OSD
Select Configuration > CON Ports in the main menu.
Menu Configuration – CON Ports
Consider the following notes to configure the OSD:
If you select VAR, the OSD will be embedded in the current screen
resolution. If the monitors have different resolutions, the OSD will be
displayed in different sizes at the various consoles.
If you select a constant resolution, the OSD will be displayed in full
screen. To this the monitor resolution will be changed. This can lead
to a delay regarding video display, both opening and leaving the
OSD.
Page 92
Draco major
92 2011-10-11
Java Tool
Select Console > CON Ports in the task area.
Menu Console – CON Ports
You can select between the following buttons:
Button Function
Copy CON Copy the settings of the selected console to the
clipboard
Paste CON
Paste the console settings from the clipboard
Reset CON Reset settings of the selected console to default
settings
Page 93
Configuration
2011-10-11 93
5.5.2 Console Matrix (CON Matrix)
You can unlock a specific selection of CPU ports for every single console
in this menu.
You have the following possibilities to access the menu:
OSD
Select Configuration > CON Matrix in the main menu.
Unlocked ports are marked in green; all the other ports are marked in
red.
Menu Configuration – CON Matrix
You can select between the following buttons:
Button Function
All Selection of all CPUs
None Deselection of all CPUs
Cancel Abort data transfer without saving
Page 94
Draco major
94 2011-10-11
Button Function
Save Save data transfer
The options All and None have to be confirmed with Save or rejected with
Cancel.
Java Tool
Select Console > CON Matrix in the task area.
Menu Console – CON Matrix
You can select between the following buttons:
Button Function
Copy Matrix Copy the settings of the selected console to the
clipboard.
Paste Matrix
Paste console settings from the clipboard
Page 95
Configuration
2011-10-11 95
5.5.3 Mouse and Keyboard
Mouse and keyboard specific adjustments can be made in this menu.
You can select between the following settings:
Field Selection Description
Hor. Speed 1/x
1-9
Adjustment of the horizontal mouse
speed (default: 4).
Ver. Speed 1/x
1-9
Adjustment of the vertical mouse speed
(default: 5).
Double Click
100-800
Milli-
seconds
Adjustment of the time slot for a double
click (default: 200 ms)
Keyboard
Layout
Region
Set the OSD keyboard layout according
to the used keyboard (default: English
(US)).
Y (Yes) Execute OSD commands with a single
click (relevant with the use of touch
screens to control the OSD).
Single Click
N (No)
Function not active (default)
The mouse and keyboard settings are console specific and can be
separately set for any console.
Page 96
Draco major
96 2011-10-11
OSD
Select Configuration > System in the main menu.
Menu Configuration – System
Page 97
Configuration
2011-10-11 97
Java Tool
Select Console > Keyboard/Mouse in the task area.
Menu Console – Keyboard/Mouse
You can select between the following buttons:
Button Function
Copy K/M Copy keyboard/mouse settings of the selected
console to clipboard.
Paste K/M Paste keyboard/mouse settings of the selected
console from clipboard.
Reset K/M Reset mouse/keyboard settings of the selected
console to default settings.
Page 98
Draco major
98 2011-10-11
5.5.4 Touch Screen
In this menu you can make touch screen specific adjustments. The OSD
of the Draco major supports the control by a touch screen.
You have the following possibility to access the menu:
USB-HID based touch screen protocols are supported.
Support of manufacturer specific protocols by request.
Press key <F1>.
Menu Configuration – Touch
In this mask you can do the calibration of your touch screen for every
single console. For this purpose you are required to click at least two
times at a point at the top left and at the bottom right. After that you will
have the opportunity to check the calibration, to save it or to abort it.
The calibration has to be done for every single touch screen at any
console.
Page 99
Configuration
2011-10-11 99
The control by touch screen corresponds to the mouse control as far as
possible. For a smoothly control of the OSD by a touch screen, the
activation of the mouse/keyboard setting Single Click in the OSD is
recommended (see Chapter 5.5.3, Page 95).
Page 100
Draco major
100 2011-10-11
5.5.5 Macro Keys
The programming of the macro commands for switching can be done in
this menu.
You have the following possibilities to access the menu.
The macros are separately deposited for each console. For the use of the
macros, you need a macro keyboard from the range of accessories that is
connected to one of the USB-HID ports of the appropriate CON unit.
Alternatively, the execution of the macros can also be done by 'Hot Key'
and the function keys <F1>–<F12>.
If keyboard, mouse and a macro keyboard should be used at the same
time, you will have to use an extender with four USB-HID ports or an USB
hub.
You can select between the following settings:
Field Selection Description
Connect P1 to P2 Set bidirectional connection from
console P1 to CPU P2
Connect Video
P1 to P2
Set video connection from console P1
to CPU P2
Disconnect
Disconnect console P1
Open P1
Open configuration file P1
Save
Save current configuration to the matrix
Save As P1 Save current configuration into
configuration file no. P1
Function
(01–08)
Logout
Logout current user
P1
1-16
Number of the console that has to be
connected to a CPU
Number of the configuration file
(default: 0).
P2
1-32
Number of the CPU that has to be
connected to the console
Loading...