Page 1
Model iC50
Charging alarm clock
radio speaker for your
works with
free alarm app
search “iHome Sleep”
Android™ phone and
other device
SMARTDESIGN
for android™
QUESTIONS? Visit www.ihomeaudio.com
Page 2
WELCOME
Thank you for choosing the SmartDesign Series for Android
featuring SmartSlide™ docking to charge your Android device in any
position. This user guide will get you up and running quickly and
provide helpful hints to maximize enjoyment. For more information
about this and other iHome products, please visit
www.ihomeaudio.com Note that details on using iHome apps for
Android with this unit are not covered in this booklet. For
information on using iHome apps for Android, please visit
www.ihomeaudio.com/apps
GETTING STARTED
This unit ships with the following items. Please check to see that all
items are present.
1 iC50 speaker system
2 SmartSlide™ USB to micro USB cable
3 Stereo audio cable w/ 3.5 mm plug ends
4 100-240V Universal AC power adaptor
micro
USB plug
standard
USB plug
12
34
1
Page 3
FEATURES & FUNCTIONS
Device rest
Top panel
SmartSlide™ insert
Connection
compartment
Aux line-in Jack
Mode button
Power On/Off
button
Reverse & Forward
buttons
Snooze/Dimmer button
Back panel
DST Switch
DC Jack
Charging switch
USB port
Sleep button
Alarm button
Volume control buttons
FM antenna
Time set button
Display
Buzzer Volume Indicator
PM Indicator
FM Radio
Indicator
Buzzer/Radio
Indicator
Time Display
Sleep Indicator
Low Backup Battery Indicator
Alarm
Indicator
AUX-In
Indicator
DST Indicator
2
Page 4
CONNECTING TO AC POWER
This unit operates on AC power
using the included 100V-240V
universal AC adaptor for charging
and playing devices .
RESET
Place unit on a stable surface. Plug
the power adaptor into the AC jack
on back of the unit and the other
end into a working wall socket. You
can now charge devices connected
to the USB port.
RESET
TEST
TEST
7.5V 2.5A
BACKUP BATTERY
The iC50 ships with a CR2450 battery installed for backup to provide
continuous alarm operation and clock settings in the event of a power failure.
Remove the pull tab from the battery compartment on the bottom of the unit
before use. If a power failure occurs or the AC cord is accidentally
disconnected, the display backlight will not remain lit, but current time and
alarm time settings will be temporarily maintained. Otherwise, you must reset
the time and alarm settings.
Note: The Battery Low icon is located at the right side of clock display.
When the backup battery is low and needs to be replaced, the Battery
Low icon will flash. To replace, follow steps below:
3
Page 5
BACKUP BATTERY (CONTINUED)
1. Please make sure the AC adaptor is connected. Otherwise all settings
may be lost during battery replacement.
2. Use a Phillips screwdriver to open the backup battery compartment
door located on the bottom of the unit.
3. Remove the exhausted battery. Insert a
new CR2450 battery by easing it under the
tabs in the battery well and pressing down.
Make sure the side marked + is facing up.
Close the compartment door.
4. Close the battery compartment door and
tighten the battery door screw.
Note: Make sure you dispose of battery
properly (see your local regulations).
WARNING: Lithium batteries can explode or cause burns if disassembled,
shorted, recharged, exposed to water, fire, or high temperatures. Do not
place loose batteries in a pocket, purse, or other container containing metal
objects, mix with used or other battery types, or store with hazardous or
combustible materials. Store in cool, dry, ventilated area. Follow applicable
laws and regulations for transport and disposal.
4
Page 6
SMARTSLIDE™ DOCK
This unit features a SmartSlide™ dock insert (patent pending), which allows
you to dock and charge your Android device whether the micro USB port is
located on the left, right or bottom of the Android device.
1. Lift the dock
insert from unit.
3. Place the connector at
the end of the track.
Rotate the connector
(up to 180°) to face
the same
direction as
2. Drop the micro-USB
cable through the
insert.
your device.
5
Page 7
4. Slide the connector
onto the track.
5. Plug in the micro USB
cable and wrap the
cord. (also a good
time to insert the
audio cable, described
on pg. 7)
6. Snap in the docking
insert again. Unit is
now ready to charge
your device.
Charging your Android Device
Make sure your Android device’s firmware is up to date before use
(consult the user manual of your Android device). Carefully dock your
Android device onto the SmartSlide dock. Once the SmartSlide cable is
connected to both your Android device and the unit’s USB port, monitor the
Android device to observe its charging status. If it does not appear to be
charging, move the USB Circuit Switch located in the connection compart-
ment to the other position ( or ) and reconnect the charging device
again. NOTE: unit will only charge while connected to power with AC
adaptor.
6
Page 8
Guide cable through dock
or back of insert to connect
plug to headphone jack on
your Android device
PLAYING MUSIC
LINE-IN JACK
Connect one end of the included stereo 3.5mm audio cable into the
line-in jack located in the connection compartment and the other end
into the headphone jack on your Android
If the headphone jack is on the bottom of the Android device, guide
plug through the SmartSlide. If headphone jack is elsewhere, guide the
audio cable up through the notch in the rear of the docking insert and
connect to your device. Press the Power Button on the unit. Next,
press the Mode Button as needed until the audio icon appears on the
display. Put your audio device in play mode. Press the Volume
Buttons on the unit to adjust listening level. When you are through
TM
phone or other audio device.
listening, stop or pause play on your audio device. In about 3 minutes,
the icon will disappear and the unit will shut off.
TIP: To turn on unit automatically, connect the audio cable to already-
playing Android; the unit will power on when the audio is detected.
7
Page 9
SETTING THE TIME
The unit features a Daylight Saving Time (DST) Button for quickly adjust-
ing the time at the start or end of Daylight Saving Time. Press and release
the DST Button at any time to toggle between On (adds one hour) and Off
(subtracts one hour). When set to On, a DST icon appears on the
display.
1. Press and hold the Time Set Button located on the back of the unit until
the hour flashes in the display.
2. Press the + or – Buttons to set the hour. Make sure you are setting the time
to the correct AM or PM time. The PM indicator appears at the upper left
of the display; there is no AM indicator. NOTE: The time can be set to
standard 12 hour time (AM and PM) or to 24 hour time (sometimes called
“military time”). To toggle between 12 and 24 modes, press and release the
Alarm Button (located on top of the unit) at any time during time
setting mode.
3. Press and release the Time Set Button to confirm the hour setting. The
minutes will begin flashing. Press the + or – Buttons to set the minutes,
then press and release the Time Set Button to confirm the current setting
and exit time setting mode.
SETTING AND USING THE ALARM
SETTING THE ALARM
This unit lets you wake to FM radio or built-in buzzer alarm. The alarm
will sound for 60 minutes or until reset/turned off.
1. Press and hold the Alarm Button until the alarm time display flashes.
2. Press the + or – Buttons to adjust the display to the desired alarm time (hold
for rapid adjustment). Remember to set the correct AM or PM alarm time.
8
Page 10
SETTING AND USING THE ALARM
(CONTINUED)
3. Press the Alarm Button to confirm the alarm time. The wake-to
indicator will flash on the display. Press the + or – Buttons to toggle
between wake to buzzer and wake to radio settings.
Wake to Buzzer: If wake to Buzzer is selected, press the + or – Buttons to
choose HI or LO buzzer alarm volume.
Wake to Radio: If wake to Radio is selected, press the + or – Buttons to select
the desired radio station (press and hold to scan to next clear
station). Press the Alarm Button to confirm radio station
selection. Next, press the + or – Buttons to adjust the wake-up
radio volume (can be set from 5- 40).
4. Press the Alarm Button to exit and confirm alarm settings. An alarm
icon will appear on the display, indicating that the alarm is set and armed.
TIP: Download the FREE iHome Sleep app from the Android Market to enable
your Android music as wake to alarm source!
Reviewing and Resetting the Alarm
Press the Alarm Button at any time to review the current alarm settings.
To toggle the alarm on or off, press the Alarm Button as needed. When
the alarm icon is displayed, the alarm is armed/on.
Press the Power Button or Alarm Button when the alarm is sounding
to reset it to come on again at the same time the next day. Press the
Alarm Button again to turn off/disarm the alarm. The alarm icon will
disappear.
SNOOZE FEATURE
You can interrupt the alarm by pressing the Snooze/Dimmer Button while
the alarm is sounding. The alarm will resume at the end of the set snooze
time. The snooze duration time is adjustable. To change the snooze time
from the default (9 minutes), press and hold the Snooze/Dimmer Button
during normal operation (when alarm is not sounding) until the snooze time
flashes in the display. Press the + or – Buttons to adjust the time between 1 and
29 minutes), then press the Snooze/Dimmer Button to confirm.
9
Page 11
FM RADIO
Fully extend the FM radio antenna on the back of the unit. Do not alter,
strip or attach to other antennas.
Press the Mode Button to access FM radio mode. If off, the unit will
power on. The currently tuned station frequency will appear in the
display.
Press the + or – Buttons to tune to a desired FM radio station; press and hold
to scan rapidly to the next clear station. Press the Volume Buttons on
the unit to adjust listening level. When you are through listening, turn the
unit off by pressing the Power Button.
USING THE RADIO IN OTHER COUNTRIES
Different regions of the world use different FM radio frequency steps and
ranges. You will need to select the one that matches the standards in your
region (USA, EUROPE, JAPAN, AUSTRALIA,or CHINA). The default setting is
USA; if you live in the US, you may skip this section.
1. Make sure the unit is OFF (not playing in any mode). Press and hold the
Mode Button for about 5 seconds until “FM” and the region flashes in the
display. Press the + or – Buttons as needed to set the display to your region:
USA, EU (Europe), JPN (Japan), AUS (Australia), or CHN (China).
2. Press and release the Mode Button again (or no button within 10 seconds)
to exit the radio frequency setting mode. Two beeps will confirm radio
frequency setting.
SLEEP MODE
Sleep mode lets you sleep to the current FM radio station. Press the Mode
Button to access FM radio mode. Press the Sleep Button as needed to
cycle to the desired sleep duration: 120, 90, 60, 30 or 15 minutes or OFF
(turns sleep mode off). Press the Volume Buttons on the unit to
adjust sleep listening level. The unit will revert to normal volume level
when sleep mode ends. Press the Sleep Button during sleep to view the
remaining sleep time; press again to set sleep to next (lower) sleep
duration.
10
Page 12
TROUBLESHOOTING
Symptom Possible reason Solution
Erratic
performance
No sound
Sound distorted
Device doesn’t
charge up
External interference
Volume is too low
Volume is too high
Sound source is distorted
Unit is not connected to
AC power
Move unit away from potential sources of
external interference such as computers,
modems, wireless devices (routers) or
fluorescent light.
Turn volume up on your device
Turn volume down on your device
If the original sound file (MP3) is old or of
poor quality , distortion and noise ar e
easily noticed with high-power speakers.
Try upgrading file from a trusted source
such as iTunes.
Please make sure the unit is connected
to a working power outlet. The unit will
not charge while operating on batteries
Device uses a proprietary
charging protocol
USB cable is not
connected properly
Move the USB Circuit Switch found next
to the USB port to the other position and
monitor the charging status on your
device. If it still does not charge, your
device may require you to use the
charging accessory that came with it.
Check that the USB plug is firmly and
correctly connected to the USB port on
the side of the unit and that the other
end is properly connected to your device
11
Page 13
TROUBLESHOOTING
Symptom Possible reason Solution
Unit won’t turn on
Device does not
respond to the
unit and/or
device is playing
but no sound
comes out
AC adaptor isn't plugged into
a working wall socket or not
plugged into the power jack
on back of the unit
Audio cable and device are
not connected properly
Unit is not properly connected
to power source an/or Power
Button is not ON
Plug the AC adaptor into a
working wall socket and plug the
connector into the supply jack on
the unit. Make sure any associated
wall switch that controls the outlet
the is ON.
Check the volume setting on your
device. Make sure your device is
working properly before
connecting. Check that the audio
cable is firmly connected to both
the line-in jack and to the
headphone/audio out jack on your
device
Make sure the unit is properly
connected to AC power source.
Check that the Power Button is lit
up, indicating the unit is ON.
Unit won’t turn off
This unit uses audio detect
circuitry to enable alarm apps
to function properly. The
power button is disabled
when playing audio from a
device.
To turn off the unit when done
playing audio via the line in jack,
stop or pause play on your audio
device. The unit will power off
automatically in about 3 minutes.
MAINTENANCE
• Place the unit on a level surface away from sources of direct sunlight or
excessive heat.
• Protect your furniture when placing your unit on a natural wood and
lacquered finish. A cloth or other protective material should be placed
between it and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water.
Stronger cleaning agents, such as Benzene, thinner or similar materials
can damage the surface of the unit.
12
Page 14
IMPORTANT SAFETY TIPS
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in
potential electrical shock or fire hazards. Please read all safety and operating
instructions carefully before installation and use, and keep these instructions
handy for future reference. Take special note of all warnings listed in these
instructions and on the unit.
1. Water and Moistur e – The unit should not be used near water. For example:
near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a
wet basement.
2. Ventilation – The unit should be situated so that its location or position does
not interfere with its proper ventilation. For example, it should not be
situated on a bed, sofa, rug or similar surface that may block ventilation
openings. Also, it should not be placed in a built-in installation, such as a
bookcase or cabinet, which may impede the flow of air through the
ventilation openings.
3. Heat – The unit should be situated away from heat sources such as
radiators, heat registers, stoves or other appliances (including amplifiers)
that produce heat.
4. Power Sources – The unit should be connected to a power supply only of
the type described in the operating instructions or as marked on the
appliance.
5. Power-Cable Protection – Power supply cables should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them. It is always best to have a clear area from where the cable
exits the unit to where it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the
Maintenance section of this manual for cleaning instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall
and liquids are not spilled into any openings or vents located on the
product.
8. Attachments – Do not use attachments not recommended by the product
manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall
socket and disconnect the antenna or cable system during a lightning
storm or when it is left unattended and unused for long periods of time. This
will prevent damage to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified
service personnel when:
A. the power supply cable or plug has been damaged.
B. objects have fallen into or liquid has been spilled into the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E. the unit exhibits a marked change in performance or does not operate
normally.
13
Page 15
IMPORTANT SAFETY TIPS(CONTINUE)
12. Periods of Non use – If the unit is to be left unused for an extended period
of time, such as a month or longer, the power cable should be unplugged
from the unit to prevent damage or corrosion.
13. Servicing – The user should not attempt to service the unit beyond those
methods described in the user’s operating instructions. Service methods
not covered in the operating instructions should be referred to qualified
service personnel.
14. Magnetic Interference: This product’s speakers contain powerful magnets
which could cause interference or damage to sensitive equipment such as
hard drives, CRT televisions and monitors, as well as medical, scientific,
and navigational devices. Keep this unit away from these products at all
times.
A GUIDE TO PRODUCT SAFETY
This device complies with Part 15 of the FCC Rules, operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
• Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable pr otection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
14
Page 16
LIMITED 1 YEAR WARRANTY
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies),
warrants this product to be free from defects in workmanship and materials, under normal use and
conditions, for a period of 1 Year from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store
where it was originally purchased. Should this fail to resolve the matter and service still be required
by reason of any defect or malfunction during the warranty period, SDI Technologies will repair or, at
its discretion, replace this product without char ge (except for a $10.00 charge for handling, packing,
return UPS/postage, and insurance). This decision is subject to verification of the defect or
malfunction upon delivery of this product to the Factory Service Center listed below. The product
must include proof of purchase, including date of purchase. The fee for service without proof of
purchase is $20.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh
ones, as exhausted or defective batteries are the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of
purchase, if within the warranty period.
3. Enclose a check or money order payable to the order of SDI T echnologies, for the sum of $10.00
($20.00 without proof of purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Dr.
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It
does not cover (i) products which have been damaged by negligence or willful actions, misuse or
accident, or which have been modified or repaired by unauthorized persons; (ii) cracked or broken
cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape
cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service Center and its
return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the
product other than to the original purchaser. In no event will SDI Technologies or any of its affiliates,
contractors, resellers, their officers, directors, shareholders, members or agents be liable to you or
any third party for any consequential or incidental damages, any lost profits, actual, exemplary or
punitive damages. (Some states do not allow limitations on implied warranties or exclusion of
consequential damages, so these restrictions may not apply to you.) This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
Your acknowledgment and agreement to fully and completely abide by the above mentioned
disclaimer of warranty is contractually binding to you upon your transfer of currency (money order,
cashier's check, or credit card) for purchase of your SDI Technologies product.
Questions? Visit www.ihomeaudio.com Toll Free Customer Service: 1-800-288-2792
©SDI Technologies 2012 All rights Reserved
iC50-02072012-A Printed in China
Loading...