Installation Manual
Wireless Pet-Immune Motion Sensor
Website : www.iget.eu E-mail : sales@iget.eu
SECURITY M3P14
Safety precautions
1. Use the device only and exclusively in accordance with this manual. Failure to follow instructions can lead to fire or damages to the device.
2. For safety reasons protect the device from falling, shortage of electric circuits and high temperatures. If the device or battery suffers from distortion and
cause damage to the device, stop using the device immediately.
3. Keep out of the reach of children. Only adult persons may use the device. Its owner is responsible for using of this device by other persons.
4. There is a battery inside the product. For safety reasons do not approach the product with metal objects, which could cause a short circuit.
5. The product must not be installed and used in hot (more than 40°C) or cold (less than -10°C) environment. At the same time the product must not be
installed and used in humid (more than 90%) or dusty environment, or in the vicinity of fire.
6. Do not expose the product to direct sunlight and heat radiation and do not cover it, i.e. it must have a permanent supply of colder ambient air.
7. Do not expose the product to direct contact with liquids (water); do not use any corrosive cleaning agents for cleaning including alcohol. Use only a dry
cloth.
8. The device must meet the requirements needed to use direct current; using a different power source may cause fire or malfunction.
9. A strong impact can lead to fire or explosion.
10. When using the product make sure that you have dry hands. Otherwise, it can cause damages to the product or electrical accident.
11. Set up the claim for warranty repair of device at your dealer. If you have technical questions or problems, contact your dealer.
12. For household use: The given symbol (crossed-out wheeled bin) on the product or at accompanying documents means that used electrical and electronic
products should not be disposed of with household waste. To ensure proper disposal of the product, hand it over to a designated collection point, where it
will be accepted free of charge. The correct disposal of this product will help to save valuable natural resources and prevent any potential negative impacts
on the environment and human health, which could otherwise be caused by inappropriate disposal of wastes. For more details, please, contact your local
authorities or the nearest collection point. The improper disposal of this waste can be penalized in accordance with national regulations. Information for users
to disposal of electrical and electronic devices (corporate and business use): For proper disposal of electrical and electronic devices, ask for details from your
dealer or distributor. Information for users to disposal of electrical and electronic devices in other countries outside EU: The above mentioned symbol (crossedout wheeled bin) is valid only in the countries of EU. For proper disposal of electrical and electronic devices, ask for details from your authorities or dealer. All is
expressed by the symbol of crossed-out wheeled product bin on packaging or in printed materials.
13. To make a claim it is necessary to know the serial number of product, indicated on the back side of product and the packaging box. Please, keep the box
with serial number carefully for any complaints, you will avoid the unnecessary inconveniences or to be unable to establish a claim.
Make a complaint of the product at your dealer, if not on website www.iget.eu stated otherwise.
Individual parameters, description by figures and design may differ depending on the version and updates. For exact parameters and other product
information visit the website www. iget.eu. Printing errors reserved. The manufacturer and importer have no liability for data loss or other damages arising
howsoever when using Power bank.
Declaration of Conformity:
Company INTELEK spol. s r.o. hereby declares that all SECURITY M3P14(DYG06B) devices are in compliance with essential requirements and other
relevant provisions of Directive 2004/108/EC. The products are intended for sale without limitation in the Czech Republic, Slovakia, Poland, Bulgaria,
Germany, Austria, Belgium, Denmark, Finland, Greece, Netherlands Ireland, Great Britain, Norway, France, Spain, Italy, Hungary, Lithuania, Latvia, Estonia,
Romania and other member countries of EU and in Russia. The warranty period of the product is 24 months, unless stated otherwise. The Declaration of
Conformity can be downloaded from the website www.iget.eu.
Operating Instructions
1. Working principle
The sensor sends trigger signal to the paired main panel when the build-in smoke sensor is triggered.
2. Pairing with main panel by App
①
Scan the QR code printed on the sensor.
②
The pairing result would be confirmed by SMS sent from main panel.
3. Use
The alarm is provided with a test button. Press this until the alarm signal sounds.The signal stops once the button is released.
Test the alarm at least once perweek, and certainly after replacing the battery or after cleaning, with a vacuum cleaner for
example. The alarm must be vacuumed regularly to remove dust particles and to protect it as well as possible. If the alarm fails
to operate correctly, please contact with dealer or manufacturer.
Features
Parameters
Appearance
The M3P14 wireless smoke sensor is an accessory of SECURITY M3 series smart alarm system. By using unique design and MCU
to work with photo-electricity signal, it is dust-proof, pest-proof, anti-optical interference, etc. This product responds well to
the smoke of smoldering and burning. With build-in photoelectric smoke sensor, it will trigger alarm when the smoke density
reaches the alarm threshold.
Installation
Notice
• Open the case and insert the battery.
• Pairing it with main panel before installing.
• Choose a proper position, normally the center of the detection area ceiling is recommended. Please fix the sensor base into
the chosen position with screws. Be sure it is fastened tightly.
• Avoid installing sensor in places with
• stagnating smoke
• heavy dust, heavy water mist or heavy oil mist
• great humidity(>95%)
• high wind speed(>5m/s)
• To ensure the sensitivity, please clean the sensor surface with soft bristled brush every 6 months. Make sure to shut off the
power before cleaning.
• Contact your dealer when there is any problem about the product. DO NOT attempted to repair the sensor personally.
• The sensor can reduce the happening rate of disasters. But there is not guarantee for 100% safe. For your safety, please use
this sensor properly and be vigilant in daily life.
• Working Voltage DC 9V
• Battery 9V (1x 6F22/ 6LR61 Battery)
• Working Current ≤20mA
• Standby Current ≤100 μA
• Alarm Sound ≥ 85dB/3m
• Product Certication BS EN 14604: 2005
• Transmission Distance Without obstacle 100m
• Transmission Frequency 433.29MHz
• Working Temperature -10℃~40
℃
• Humidity ≤90%rh (non-condensing)
• Weight 98.7g (battery not included) 134.5g(battery included)
• Dimension Φ 107mm * Δ 34mm
Test Button & LED Indicator Back Cover
buzzer
Battery replacement instructions
①
Open the case by twisting the back cover
.
②
Replace with 1 x 6LR61/6F22 battery
1 2
Loading...