Iget SECURITY M3P13 Installation Manual
Installation manual
Wireless Keypad
Website : www.iget.eu E-mail : sales@iget.eu
Support: www.iget.eu/helpdesk
SECURITY M3P13
program password
123123
program password
123123
Advanced Operations
Use to quit settings without saving.
Please disarm from keypad before any advanced operation.
Enter Setting Menu
enter:
123123
Arm Button
Operate Password
operate password
123456
operate password
123456 please input
please input
successfully
successfully
wireless Coding
address
Factory setting
setting
RF Coding
Coding
system time set
xx/xx/xx 12:00
Please know exactly what you are doing when processing the operations below. It could cause errors
or erase settings which make keypad stop working.
Change Operate Password
Change Program Password
Select Operate Password
Select Program Password
Enter New Password
Enter New Password
Done
Done
①
Pair the keypad with the main panel
②
Pair the main panel with the keypad
Time Setting
Factory Reset
Change Wireless Control Address
Pair the keypad with the main panel first, then pair the main panel with the keypad.
After that, the main panel and the keypad could synchronize the status with each other.
Working with the Main Panel
Advanced Operations
Launch APP iGET SECURITY
Select RF Coding and
press confirm .
Select System Time Set.
Select Program Password
This setting is used by engineers for maintenance.
Changing it might cause errors to your keypad.
We just show you the menu but hide the details for your safety.
When screen shows like this,
trigger SOS from App.
Use and to set one by one,
Use and to adjust the time,
Press to confirm settings.
Restoring Settings
with a Long Beep
Keypad would show some
codes when receive any SOS
signal from main panel.
Done.
Done.
Pairing finished.
Scan the QRCode printed on the
keypad
Rename the Keypad
Done
RF Coding
Coding
system time set
xx/xx/xx/ xx:xx
factory setting
restore
4cf70c000
Normal code
xx/xx/xx/ xx:xx
restore
factory settings
00000000
Trigger remote
successfully
20141129/150
us
successfully
Error
Repeated code
Hint:
“Error Repeated Code” means the main panel
has been paired with this keypad before.
wireless Coding
address
Caution: For professional use ONLY.
Reset will cause communication failure between keypad and main panel.
1 2 3
Features
Parameters
Appearance Front
The iGET SECURITY M3P13 wireless keypad is an accessory of iGET SECURITY M3 series smart alar m system. It enables
convenient operations to arm/disarm/home arm/trigger SOS. It can control the main panel actively and receive command
from main panel. Password control and tamper alarm function make it safe and reliable.
• Working Voltage DC 5V
• Battery 500mAh 3.7V Rechargeable Li Battery
• Battery Standby Time 12-20hours
• Working Current 16.5mA
• Charging Current 200mA
• Standby Current 11mA
• Transmission Distance Without obstacle 80m
• Transmission Frequency 433.29MHz
• Working Temperature 0℃~50
℃
• Humidity ≤90%rh (non-condensing)
• Weight 117.6g
• Dimension 134.0 * 87.4 * 14.7 mm L*W*H
1. Screen
POWER: RED
It lights on when the keypad is power on; and
lights off when it’s power off.
SIGNAL: BLUE
It flashes when the keypad receives wireless
signal.
ALARM: RED
It flashes quickly when it receives alarm signal
from alarm control panel or the SOS alarm is
triggered by the keypad itself.
2. LED Indicators
In standby status, it displays
the keypad state and system
time.
Arm
Home Arm
Right
Disarm
SOS
Comfirm
Left
Up
Down
Back/ Clear
Power Switch
Groove Approach
Power Connection
Before Operating
Anti-tamper Switch
Please make sure the panel and the keypad have been paired with each other. If not, please check hereinafter
“Advanced Operations”—“Working with the Main Panel”.
To operate this keypad, you should always key in the operate password before ARM, DISARM, etc.
To set this keypad, you should always key in the program password before any advanced settings.
Operate Password: For Daily Use
Operate Password: For Maintenance and Settings
Appearance Back
enter:
123456
enter:
123123
ARM
Pairing
DISARM
Reset
......
......
Daily Operations
Advanced Settings
Default Operate Password
Default Program Password Menu Select
Daily Operation
After successful operation, there will be a long beep, and the screen will display “SYSTEM ARMED “ with flash per every second.
If the main panel is armed by remote controller or other method but not the keypad,
the screen will display “SYSTEM ARMED” without flash.
After successful operation, there will be a long beep, and the screen will display
“SYSTEM DISARMED “ with flash per every second.
If the main panel is disarmed by remote controller or other method but not the
keypad, the screen will display “SYSTEM DISARMED” without flash.
After successful operation, there will be a long beep, the ALARM indicator will be on
and keep flashing, and the screen will keep display the previous status.
After successful operation, there will be a long beep, and the screen will display “HOME ARM “
with flash per every second.
If the main panel is home armed by remote controller or other method but not the keypad,
the screen will display “HOME ARM” without flash.
Arm
Disarm
SOS
Home Arm
enter:
123456
enter:
123456
enter:
123456
enter:
123456
Arm Button
Disarm Button
SOS Button
Home Arm Button
Operate Password
Operate Password
Operate Password
Operate Password
System armed
02/10/14 17: 04
System DISarmed
02/10/14 17: 04
HOME ARM
02/10/14 17: 04
Loading...