IGC WIPL15B A User Manual

Precautions

Safety Precautions

Do not use the product with wet hands. It may cause malfunction

and there is a risk of electric shock.

Do not leave the product inside the vehicle while a cell phone is

placed on the charger.

Make sure to support rear side with your hand when you press the

home button on your phone.

Cautions for Product

Charging efficiency may vary depending on the characteristics of

cell phones.

Cell phone may not be charged or charging efficiency may be

impaired if the cell phone case is thicker than 5 mm.

Details and figures included in this Manual are subject to change

without prior notice for improving the quality of product.

If you disassemble or attempt to repair the product by yourself,

warranty may be voided.

Product has limited shock resistance, and may break if dropped

or struck.

IGC is not responsible for any injury or loss of user that is caused

by any other means that are not mentioned in this Manual.

Troubleshooting

The following may occur as part of normal operation of the product.

Mild heat can be generated on the cell phone while charging the

battery, but this is naturally caused by the heat generated on the
battery charger.

If you use navigation or watch video clips, your cell phone, it is nor-

mal for your cell phone to get warmer due to overuse of electricity.

The product may not charge if connected to a multi-way cigarette

lighter socket (power distributor), due to an insufficient power
supply.

Verification number MSIP-RMM-igc-WIPL10B

Company name IGC Co.,Ltd.

Model name WIPL10B

Manufacturer IGC Co.,Ltd.

Manufactured date 2015. 02

Manufacturing country Republic of Korea

1644-5287

Service Center

Halla SigmaValley #606
212, 1gongdan-ro, Gumi-si, Gyeongsangbuk-do, Korea

www.wi- pl. com

User’s Manual

Solving heating
problem

Solving charging
problem

Qi standard

Wireless car
charger

Package Components

* Receiver and auxiliary film for attaching magnetic sticker may vary depending on the

type of cell phone.

Product Specifications

Cate gory Speci fications

Size of bat tery charger

Weight of ba ttery charger

Input volta ge/current of bat tery charger

Wireles s charging output

Wireles s charging type

Output volt age of wireless rec eiver

Operation ran ge for wireless charg ing

Weight of cel l phone that can be used
on the cradl e

12 cm x 7 cm x 7 cm

Approx. 140 g

5 V / 2 A (MicroU SB 5Pin)

5 V / 1 A

QI standa rd regulation

5 V / Output curren t: 800 mA

5 - 8 mm

400 g or belo w

Product Characteristics

Wi-Pl has excellent compatibility for which it can be used to

charge most newly launched types of cell phone.

It uses a glass absorption type cradle that can be adhered to any

other suitable surface.

It uses powerful neodymium magnet to hold the phone, making it

convenient for users to attach/detach the product with one hand.

It is applied with location induction technology which makes it

easier to charge the battery in appropriate charging location and
enhance the energy efficiency and solve the problem of overheat.

Product Installation

1 2

The receiver is installed in three different ways depending on the
type of cell phone.

Make sure to check the type of cell phone before installing

product. Refer to our website (www.wi-pl.com) for details.

The receiver is installed in different ways depending on the
type of cell phone. Check the type of cell phone that is most
appropriate for the user and attach the receiver following the
procedures for attaching receiver of each type. If you have
completed attaching the receiver, attach the magnets following
the procedures for attaching the magnetic sticker.

This User’s Manual explains the procedures for attaching the
receiver for two types of cell phone: cell phone in which parts for
wireless charging is not installed and cell phone in which parts for
wireless charging is partially installed.

Attaching receiver on cell phones in which parts
for wireless charging are not installed

It applies to models that do not include parts for wireless charging such
as iPhone.

1 Remove the cover that is

protecting the sticker from
receiver.

2 Align the receiver with the

bottom of the cell phone
following the guideline of receiver.

3 Attach the receiver to cell phone.
4 Connect the receiver jack to the cell phone.

Attaching receiver on cell phones in which parts
for wireless charging are partially installed

Model (example): Samsung Galaxy S5

1 Remove the cover that

is protecting the sticker
on the front side (logo)
of receiver.

2 Open the battery

cover of the cell phone
and adjust the metal
contacts of the receiver
with the metal contacts
inside the cell phone.
Then, attach the
receiver to the battery.

* Location of metal contacts

inside cell phones may vary
depending on the cell phone.

3 While the receiver is

attached to the battery,
remove the large cover
that is protecting the
sticker on the rear side
of the receiver.

4 Close the battery cover

and push the cover
so that the receiver
adheres to the inside of
the cover.

Attaching receiver on cell phones in which parts
for wireless charging are installed

Some of the models (e.g. Nexus series and some types of Nokia) come
equipped with a wireless receiver, and it is not necessary to attach an
extra receiver. Please contact the manufacturer to find out if the product
includes parts for wireless charging.

Attaching magnetic sticker

1 Remove dust and water on the rear side of cell phone case or

the cell phone.

2 Remove the four protecting covers of magnetic sticker.

The design of protecting cover may vary. Remove all protecting
covers.

3 Align the auxiliary film with the rear side of cell phone and

attach the magnetic sticker on the cell phone.

4 Remove the auxiliary film.

Auxiliar y film is designed in the same size with each type of cell

phone. Magnetic sticker on the auxiliary film should be attached
on the designated location for proper charging and high charging
efficiency.

Users can use the case they desire after attaching the receiver.

However, magnetic sticker must be attached on the cover or outside
the case so that they can be seen from outside.

Cases that contains metal component cannot be used as it can

cause malfunction of the product.

Ma gnetic sticker may be detached from the product depending on

the material used on the magnetic surface. Make sure to check the
material used on the surface when attaching the magnetic sticker.
(It is recommended to use the case when it is difficult to attach the
sticker due to the material used on the surface.)

Installation on vehicle

1 Remove the dust or foreign substance from the glass

or dashboard that you wish to attach the cradle (glass
absorption type).

2 Remove the dust protecting film on the bottom side of cradle.
3 Open the lever of the cradle, attach the cradle on the

location where you wish to fix it, and then close the lever.

When you wish to detach and attach the cradle again, wash up the

gel on absorption part with water before attaching it.

Make sure to check if the cradle is attached properly before driving

vehicle.

Install the cradle on the location where it does not interfere with

the driver’s sight.

If the temperature difference between inside/outside is high,

absorption may be deteriorated. Make sure to check again if the
cradle is attached properly.

Charging battery

1 Insert the cigarette jack adapter designed for vehicle into the

cigarette lighter socket on the vehicle.

2 Connect each end of the USB cable to the Wi-Pl, the bottom

socket (2.1 A) of cigarette jack adapter and to the battery
charger.

3 Attach the cell phone on the battery charger. The green light

turns on at the battery charger, and the charging starts.

Upper (1 A) socket can be used for charging with cable.

When the power is applied, blue light turns on at the bottom part of

the battery charger and it turns to charging standby status.

When you do not use the provided parts, power may not be supplied

properly and the battery may not charge.

When the battery is completely charged, remove the charging

cable from the main body.