IFM Electronic AC1391, AC1392 Operating Instructions Manual

Operating instructions
AS-i controller
e
AC1391 AC1392
7390920/00 12/2011
UK
2
1 Preliminary note ��������������������������������������������������������������������������������������������������� 3
1�1 Notes on this document ��������������������������������������������������������������������������������� 3 1�2 Symbols used ������������������������������������������������������������������������������������������������3
2 Safety instructions �����������������������������������������������������������������������������������������������3
2�1 General ���������������������������������������������������������������������������������������������������������� 3 2�2 Installation and connection ����������������������������������������������������������������������������3 2�3 Tampering with the device �����������������������������������������������������������������������������4
3 Functions and features ����������������������������������������������������������������������������������������4
3�1 Programming interface RS232C ��������������������������������������������������������������������4 3�2 Ethernet Programming Interface �������������������������������������������������������������������4
4 Installation������������������������������������������������������������������������������������������������������������4
5 Electrical connection �������������������������������������������������������������������������������������������� 5
6 Operating and display elements ��������������������������������������������������������������������������6
6�1 LED indicators and pin connection ����������������������������������������������������������������6
6�1�1 LEDs ����������������������������������������������������������������������������������������������������� 7 6�1�2 Diagnostic LEDs �����������������������������������������������������������������������������������7 6�1�3 Status LEDs on the network connection �����������������������������������������������7
6�2 Contrast setting ���������������������������������������������������������������������������������������������8
7 Operation ������������������������������������������������������������������������������������������������������������� 8
8 Menu overview�����������������������������������������������������������������������������������������������������9
8�1 Password ������������������������������������������������������������������������������������������������������� 9 8�2 Menu navigation ������������������������������������������������������������������������������������������10
9 Technical data ���������������������������������������������������������������������������������������������������� 13
9�1 Data sheets �������������������������������������������������������������������������������������������������13 9�2 Programming manual ����������������������������������������������������������������������������������13
10 Maintenance, repair and disposal �������������������������������������������������������������������� 14
11 Approvals/standards ����������������������������������������������������������������������������������������14
12 Scale drawing ��������������������������������������������������������������������������������������������������14
3
UK
1 Preliminary note
1.1 Notes on this document
This document applies to devices of the type "AS-i controller
e
" (art� no�: AC1391 / AC1392)� It is part of the device and contains information about the correct handling of the product�
This document is intended for qualified electricians� These specialists are people who are qualified by their training and their experience to see and to avoid possible hazards that may be caused during operation of the device�
► Read this document before using the device� ► Keep this document during the service life of the device�
1.2 Symbols used
Instructions > Reaction, result […] Designation of pushbuttons, buttons or indications Cross-reference
Important note Non-compliance can result in malfunction or interference�
Information Supplementary note
2 Safety instructions
2.1 General
► Observe these operating instructions� ► Adhere to the warning notes on the product�
Non-observance of the instructions, operation which is not in accordance with use as prescribed below, wrong installation or incorrect handling can affect the safety of operators and machinery�
2.2 Installation and connection
The device must only be installed, connected and put into operation by a qualified electrician as the safe function of the device and machinery is only guaranteed when installation is correctly carried out�The installation and connection must comply with the applicable national and international standards� Responsibility lies with the person installing the device�
4
2.3 Tampering with the device
Tampering with the device is not allowed and will lead to an exclusion of liability and warranty� Tampering with the device can affect the safety of operators and machinery�
► Do not open the device� ► Do not insert any objects into the device� ► Prevent metal foreign bodies from penetrating�
3 Functions and features
• The controllere integrates one or two AS-i masters (AC1391 / AC1392, both
in accordance with the AS-i version 3�0), a mini controller and two EtherCAT interface ports�
• It controls the exchange of data to the sensor / actuator level�
• It processes the peripheral data in the integrated processor (signal
preprocessing)�
• It works as stand-alone controller with exchange of data to the PC
(visualisation)�
• It communicates with the superior control level (EtherCAT)�
3.1 Programming interface RS232C
• Baud rate 4800 to 115,200 baud
• Max� distance between controller
e
and PC: 20 m
• Potential separation from the controller
e
power supply
• Programming cable E70320 for connection to PC required
3.2 Ethernet Programming Interface
• EtherCAT
• RJ45, twisted pair
4 Installation
Fix the controllere onto a 35 mm DIN rail which has an electrically safe ground connection� The protection rating of the unit is IP 20, therefore it should be mounted in a protected location (e�g� control cabinet)�
5
UK
Ensure a condensation-free environment� Avoid excessive dust, vibration and shock� The air circulation through the vents must not be impeded�
Avoid installation in direct vicinity of frequency inverters�
5 Electrical connection
Disconnect the installation from power� Connect the unit as indicated on the terminals�
Never connect the minus potentials to each other or the minus potentials to the FE connection�
Ensure an electrically save ground connection between AS-i controller
e
(terminal FE) and ground of the unit�
Supply the controller
e
with a 24 V DC voltage (20���30V PELV), e�g� from the 24 V
power supply DN3011 from ifm electronic� The connection is made to the terminals +24 V and 0 V�
Loading...
+ 9 hidden pages