Fire Extingui
shing Unit With Hose Reel
IFEX 3000 Impulse Fire Extinguishing Technology
IF 3001/72
Manual
1. Impulse Gun IFEX 3001 Serial-n°:______________
2. Water container IFEX 3072 Fabr.-n°:______________
IFEX Technologies GmbH, Hansestr.18, D-27419 Sittensen
Telephone: +49 (0) 4282 93060 Fax: +49 (0) 4282 93026
Homepage: www.ifextechnologies.com
e-mail: info@ifextechnologies.com
Edition
3012-E-10/01-20.11.12
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Hansestraße 18, 27419 Sittensen
Instructions for Use and Operation
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 2
Table of contents
Safety Regulations ..................................................................................................................... 4
Labelling ................................................................................................................................... 5
Instruction for use and operation ................................................................................................. 6
A. Preparation..................................................................................................................... 6
B. Use and operation ........................................................................................................... 6
C. After use of the IFEX Impulse Gun and trolley ................................................................... 7
Test and filling instructions .......................................................................................................... 7
1. Testing of the equipment .................................................................................................. 8
2. Testing of the IFEX 3001 Impulse Gun .............................................................................. 9
3. Testing of the hose reel .................................................................................................... 9
4. Check the water container and the mounted fittings .......................................................... 10
5. Testing of the water and air pressure hoses including couplings etc. .................................. 10
6. Testing of the container .................................................................................................. 11
7. Filling instruction water and air pressure .......................................................................... 13
Machinery and tools for maintenance ......................................................................................... 14
Technical drawings .................................................................................................................. 15
1. Impulse Gun IFEX 3001, assembly ................................................................................. 15
2. IFEX 3072 Hose reel fire extinguishing unit, complete ....................................................... 16
3. Hose reel, assembly (1) ................................................................................................. 17
4. Hose reel, assembly (2) ................................................................................................. 18
5. Mounting rack with sledge, assembly .............................................................................. 19
6. Top Filling unit and filter, IFEX 3001/72 ........................................................................... 20
Maintenance and test certification .............................................................................................. 21
Appendix A/ Tests ...................................................................................................................... 1
1. Testing the extinguishing agent container (by an expert) ....................................................... 1
2. Testing the air pressure container of the Impulse Gun (by an expert) ..................................... 1
3. Tests according to national regulations for extinguishing agent container 72l ......................... 2
4. Tests according to national regulations for air pressure chamber of Impulse Gun .................... 3
Page | 2
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Hansestraße 18, 27419 Sittensen
Instructions for Use and Operation
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 3
Appendix B/ fitting and maintenance ............................................................................................ 1
1. Introduction ..................................................................................................................... 1
2. Routine maintenance ....................................................................................................... 2
3. Operation of the drum brakes ........................................................................................... 2
4. Brake adjustment ............................................................................................................ 2
5. Rewind problems............................................................................................................. 2
6. Leaky rotating swing joint- 3/4” water................................................................................. 3
Technical drawings .................................................................................................................... 4
1. Sliding skid, support for air cylinders ................................................................................. 4
2. Sliding skid, base frame ................................................................................................... 5
3. Water connection at hose reel .......................................................................................... 6
4. Air connection at hose reel ............................................................................................... 7
In addition: TÜV certificate, declaration of conformity, warranty.
Page | 3
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Instructions for Use and Operation
Instruction Manual
Page | 4
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Safety Regulations
BEFORE USE OF THE IFEX GUN AND HOSE REEL
PLEASE READ THE INSTRUCTION MANUAL
CAREFULLY!
NEVER AIM AT ANIMALS OR HUMAN BEINGS. MINIMUM SAFETY
DISTANCE IS 6 METERS.
BEWARE OF ELECTRICAL UNITS.
USE ONLY UP TO 1000 V;
MINIMUM SAFETY DISTANCE 1 METER.
CAUTION!
IFEX TECHNOLOGIES GMBH IS NOT RESPONSIBLE FOR ANY
DAMAGE TO ANIMALS, HUMAN BEINGS OR MATERIAL CAUSED
BY WRONG OR IRRESPONSIBLE USE
AND OPERATION OF THE IFEX 3000 IMPULSE FIRE
EXTINGUISHING EQUIPMENT.
IFEX 3000 PRODUCTS ARE DESIGNED
FOR FIRE FIGHTING PURPOSES ONLY
Page| 4
Labelling
1.
3.
FIRE EXT INGUISHER
72 LITERS WATER
2 x 34 A
OPEN
CYLINDER
VALVE
RELEASE
TRIGGER
LOCK
2.
4.
OPEN
WATER
VALVE
PULL
TRIGGER TO
OPERATE
GUN
A
Attention
Operation by trained personal only!
Safety distance to human beings 6 meters!
Be careful at electrical devices. Up to 1000V only!
Minimum distance 1 meter.
Follow instructions of manufacturer.
AFTER USE ALWAYS RECHARGE AND KEEP READY FOR OPERATION!
THE FIRE EXTINGUISHER NEEDS TO BE TESTED ONCE A YEAR.
TO BE USED WITH RECOMMENDED FIRE EXTINGUISHER
AGENTS OR ADDITIVES ONLY.
Fire extinguishing agent:
72 Liters Water
Propellant:
IFEX 3000
2x6Liters Compr. air 200 bar
IFEX Technologies GmbH, Hansestr. 18, D-27419 Sittensen, Germany
Telephone: +49(0)4282 93060 Telefax: +49(0)4282 930626
with 36 ml PL-2/94
Temperature range:
N° of approval:
Type:
+5° C bis + 60° C
P 3-6/99
IFEX 3001/72
Page | 5
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Instruction for use and operation
A. Preparation
1. Fill the water cylinder with extinguishing agent as described in para 7.1 of the
filling instructions.
2. Fill the air pressure cylinder with air as described in
Para 7.2 of the filling instructions.
3. The unit will be ready for operation as described in para 8 of the test and
filling instructions.
4. Put on personal safety wear and breathing apparatus as per standard
safety regulations.
Page | 6
B. Use and operation
1. Loose the connections of the gun at the vehicle.
2. Take the IFEX Impulse Gun, and put the strap around the shoulder.
3. Adjust the shoulder strap.
4. Hold the gun upwards at an appr. 30o vertical angle.
5. Check whether the water valve is closed.
6. Unwind the hose from the hose reel. (unlock safety catch)
7. Slowly open the air pressure cylinder valves at both air cylinders.
There will be 6 bar pressure on the water container and the water hose, and
25 bar pressure on the gun.
Note: The pressure gauge at the pressure regulator only shows the approximate
filling pressure of the air cylinder.
8. Further hold the gun upwards at an 30° vertical angle. Open the water valve.
The gun is filled, when small amounts of water spray through the splitted rubber
diaphragm of the gun. Close the water valve. Adjust the safety catch on the gun.
The Impulse Gun is ready for use.
Page| 6
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 7
10. Please note:
The Impulse-technology achieves a very high velocity in that water is shot from the gun
at a high speed. This leads to a short but powerful recoil of the gun. In order to minimize
this recoil it is advisory to move the gun forwards while shooting and to bend your
body forwards with your legs in a so-called “walking position”. Always aim slightly below
the aligned target. Pull the trigger evenly and let go immediately after the shot. The air
pressure will be refilled automatically within 3 seconds. Open the water valve and
repeat the extinguishing process as before. The most effective short range is between 1
and 10 meters. The total shot range is 16 meters.
11. When well trained in using the gun and if rapid shooting is required, simply let the
water valve open and shoot when the gun is filled. Use the refilling time to
consider where to place the next shot. For the extinguishing of smaller fires the
gun can be filled with smaller amounts of water simply by opening the water
valve for shorter periods or through a faster shooting sequence.
12. Regular training and exercise with the IFEX 3000 Impulse fire extinguishing equipment
will result in maximum fire extinguishing efficiency, reducing the time needed extinguish
fires and the amount of water used.
C. After use of the IFEX Impulse Gun and trolley
1. Close the water valve and empty the water chamber.
2. Close the air pressure cylinder valve.
3. Empty the gun by pulling the trigger repeatedly until the remaining air has left
the hoses and the gun.
4. Secure the gun by turning of the safety catch at the trigger.
5. Put the gun in the designated holder and fix it with the strap.
6. Use the rewind mechanism to roll the hose back onto the hose reel.
7. Empty the extinguishing agent container from air pressure by opening
the pressure relief valve.
8. Refill the water cylinder with fire extinguishing agent as per para 7.1 and the air
pressure cylinders as per para 7.2 of the filling instruction
Test and filling instructions
Please note carefully:
These test and filling instructions describe the standard rules for testing and maintenance by
the user of the mobile IFEX 3000 Impulse fire fighting equipment. Maintenance should be
carried out as per DIN 14406, part 4, latest edition.
Page | 7
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 8
Before testing of the IFEX 3000 Impulse fire extinguishing equipment:
WARNING!
1. Make sure the air pressure valve is closed.
2. Use the drain valve at the water container to release remaining pressure
3. Make sure there is no remaining pressure in the IFEX Gun or hose. This is done
by triggering the gun repeatedly until the remaining air in the hoses and the gun
is evacuated.
Caution!
Put on the gun according to the user manual as there may be a recoil due to the
remaining air in the gun.
1. Testing of the equipment
To ensure the perfect functioning of the equipment it is required to have it tested
by an expert at least once a year. The periods between testing of the equipment may
need to be reduced if this is required by local regulations.
1.1 Visual testing
Test the equipment's general condition (cleanliness, condition of the fittings, the
hoses, the water container, the pressure containers, the safety equipment, the gun,
the hose connections, the hose reel with safety catch, sledge mounting, the inscriptions
of the air cylinders). Equipment and fittings which are damaged will
need to be replaced immediately.
1.2 Spare parts
Use certified spare parts only. IFEX-original parts are certified.
1.3 Testing of the fire fighting equipment
according to the testing regulations for "IFEX 3072 Impulse fire fighting equipment".
1.4 Preparation
Before use of the fire fighting equipment IFEX 3072 according to the filling
instructions for "IFEX 3072 Impulse fire fighting equipment" as per para 8.0.
Page | 8
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 9
2. Testing of the IFEX 3001 Impulse Gun
Caution - note warning on page 8.
2.1 Disconnect the air pressure and water hose from the gun.
2.2 Check the shoulder strap for damage.
2.3 Check the screws at the front and back strap connections.
2.4 Check the membrane at the barrel end for damage.
(The membrane has 6 incisions from the inside to the outer side, ending appr.
6 mm from the outer side).
2.5 Check the screwed cap on top of the membrane, if necessary tighten it with the
special tool.
2.6 Check the front handle for tightness, if necessary tighten with wrench KS 13.
2.7 Check the water connection at the gun and the water coupling for damage
and cleanliness.
2.8 Check the water valve for external damage and condition of operation of valve.
2.9 Check the stability of the handle at the gun (key KS 3) as the operational
condition of the mechanism for operation.
2.10 Check the air pressure connection at the gun handle for damage and cleanliness.
3. Testing of the hose reel
Caution - note warning on page 8.
3.1 Check the hose reel and hose line for damage and corrosion.
3.2 Check the tightness of the fixing screws (hose reel to sledge).
3.3 Check the tightness of the fixing screws (mounting unit to vehicle).
3.4 Check the rewind mechanism.
3.5 Check the ease with which the hose reel can be turned. If necessary grease where
needed.(see Appendix B „Installation, maintenance of the hose reel“)
3.6 Check the air pressure connection coupling visually.
3.7 Check the hose reel water supply connection visually.
3.8 Check whether the instruction sticker is readable. (inscription as per DIN EN 3 Part 5)
3.9 Maintenance corresponding to Appendix B „Installation, maintenance of the hose reel”.
Page | 9
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
ens before reaching 6,0 bar, or if it fails to open at 6,6 bar you
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 10
4. Check the water container and the mounted fittings
Caution - note warning on page 8.
4.1 Disconnect all water and air hoses from the container, and check the couplings.
4.2 Remove the air pressure bottles from the holders, check straps for damage.
4.3 Check the water container for external damage, scratches in the paint and corrosion.
4.4 Check the water connection and the fittings at the container and the couplings
for damage.
4.5 Check the air pressure connection and the fittings at the container and the
couplings for damage.
4.6 Check the manometer for damage.
4.7 Remove the filling unit from the container by turning the handle anti-clockwise.
4.7.1 Check the filling unit for damage.
4.7.2 Check the screw-in thread and the o-ring sealing for damage.
4.7.3 Check the reducing valve and spindle thread for damage.
4.7.4 Check the safety valve for damage.
4.7.5 Check the safety thread at the handle for tightness (KS13).
4.8 Empty the water container and check the inside visually.
4.9 Check the type plate and instruction sticker for damage and readability.
4.10 Demount the filters (KS 21), and check for damage .(Filters are optional equipment).
4.11 Check the fixing of the water container on the sledge.
Reminder:
1. All couplings, threads and other parts of the extinguishing unit need to be
checked for cleanliness, and cleaned if necessary!
2. All parts which are demounted for testing need to be re-installed expertly.
3. After re-installation of all parts and re-connection of the water connection
the safety valve needs to be checked. Fill the container with water and air
pressure. The valve requires 6 bar +10% tolerance (6,6 bar). If the safety
valve op
will need to exchange it.
5. Testing of the water and air pressure hoses including couplings etc.
Caution- note warning on page 8.
5.1 Water hoses:
a) Water hose from the Impulse-gun to the delta connector.
b) Co-axial water hose (with air pressure hose inside),
both ends, each with a delta connector.
c) Connection of water hose to delta connection in the hose reel
¨ Check the water hoses visually for damage.
¨ Check the couplings at the hoses and the hoses for damage and cleanliness.
Page | 10
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 11
¨ Check delta connector plus screws for damage and cleanliness, and check safety
screw for tightness (key KS3).
5.2 Pressure hoses:
a) Pressure hose from the delta connector to the Impulse-gun.
b) Pressure hose between the two delta connectors (this hose floats in the
water hose).
c) Pressure hoses from the pressure regulators to the hose reel.
d) Pressure hose from the hose reel to the delta connectors (inside the reel).
¨ Check the pressure hoses visually for damage and cleanliness.
¨ Check the couplings at the hoses and the hose swaging sockets for damage and
cleanliness.
CAUTION!
The pressure hose in the water hose can only be checked for function while
in operational condition through triggering of the gun.
5.3 -.Testing of the pressure hose para 5.2 b) between the two delta connectors
The pressure hose between the two delta connectors needs to be demounted
every 5 years. Then remove the air connector piece and pull the air pressure
hose out of the water hose.
¨ Check the hose visually for damage.
¨ Check the connecting pieces, threads and sealings for damage.
6. Testing of the container
The air pressure container needs to be checked for
- national pressure cylinder regulations.
- cylinder valve for damage,
- external damage,
- air pressure of the container checked per test manometer,
- the check-up needs to done as follows:
1. Make sure the cylinder valve is closed:
2. Remove the pressure regulator from the bottle, fit test manometer and slowly open
the valve and read the pressure: IFEX 3072 = 6 l./200 bar, Minimum pressure
180 bar/+20°C, if less, refill.
Page | 11
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Note: The pressure meter at the pressure regulator shows the approximate filling
pressure of the pressure bottle.
6.1 Pressure regulator
Remove the pressure regulator from the pressure bottle valve (if not already done
as per 6.1 )
- Check the manometer glass for damage and cleanliness
- Check the couplings and thread for damage and cleanliness
Note the technical regulations TRB 502, TRB 532 and TRB 700.
Note the technical regulations TRB 502, TRB 532 and TRB 700.
6.2 Testing the fire extinguishing agent container
The fire extinguishing agent container needs to be tested by a competent person
according to Directive 2009/104/EC and national regulations.
Note appendix A, page 1, para 1.1.
Note the technical regulations TRB 502, TRB 532 and TRB 700.
6.3 Testing the air pressure container on the gun
The air pressure container needs to be tested by a competent person according to
Directive 2009/104/EC and national regulations.
Note appendix A, page 1, para 1.2.
Note the technical regulations TRB 502, TRB 532 and TRB 700.
6.4 Maintenance label:
Maintenance dates need to be entered on the label, which should not obstruct
any prints of the manufacturer.
Note DIN 14406-4 latest edition.
Page | 12
The Maintenance/Testing needs to be confirmed on page 20
"Maintenance record" of the manual.
Deficiencies will have to be repaired and faulty or deficient parts exchanged.
Page | 12
Only use original parts, note para 1.1 and 1.2.
After complete examination of the entire IFEX- Fire Extinguishing Unit
return the unit to operability according to page 13.
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 13
7. Filling instruction water and air pressure
7.1 Filling of the water container
a) Fill the container with fresh and clean water through the filling opening
(appr. 60 Liter).
b) Pour 36 ml (+0,05%) PL-2/94 - FC-201F in the container through the
filling opening.
c) Fill the water container with clean water 72 l -5% tolerance (-3,6 l)!
d) Tighten the top filling closure firmly.
7.2 Filling of the air pressure bottle
Check the air pressure level with a test manometer.
- Test as follows:
1. Make sure the cylinder valve is closed.
2. Remove the pressure regulator from the bottle, adjust the test manometer, open
the valve slowly and read the pressure:
IFEX 3072 = 2x6l l/200 bar, Minimum pressure 180 bar/+20°C, if less, refill.
Note: check both air pressure cylinders!
Note:
Should the mobile equipment be used for training, it will suffice to fill
the water container without fire extinguishing agent and with water only.
After training it is important to refill the water container and air pressure
bottles immediately according to para 7.1 and 7.2 , to ensure the
equipment is ready for use.
8. Getting the unit ready for use
8.1 Make sure the water container and the air pressure bottles are filled according to para
7.1 and para 7.2.
8.2 Fit the air pressure bottles to the designated mounting support.
8.3 Screw the pressure regulator to the bottle valves on the air pressure bottles.
8.4 Connect the air pressure hose from the pressure regulator to the water container.
8.5 Connect the water hose (Delta connector) to the water container.
8.6 Connect the air pressure hose (Delta connector) to the pressure regulator.
Page | 13
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 14
8.7 Place the IFEX 3001 Impulse Gun in the holder and secure it with the fixing strap.
8.8 Connect the air pressure hose (Delta connector) to the pressure regulator.
8.9 Connect the air pressure hose to the IFEX 3001 gun.
8.10 Connect the water hose to the IFEX 3001 gun (The water valve needs to be closed).
The fire extinguishing unit is now ready for use!
Machinery and tools for maintenance
The following list of tools is separate from the instructions.
The listed tools are to be used for their specific purposes only.
1. Test pressure gauge 0 bar to 400 bar
2. Double open-end wrench 13 x 15mm
3. Double open end wrench 14 x 17mm
4. Open-end wrench 21mm
5. Open-end wrench 26mm
6. Open-end wrench 27mm
7. Open-end wrench 32mm
8. Open-end wrench 36mm
9. Ring-wrench 8mm
10. Pipe angle wrench 13 x 110mm
11. Hook wrench 60-90 x 5mm
12. Hexagon screwdriver 3mm
(for inner hexagon screw)
13. Grease gun with lubricating grease
Torques:
¨ Front support grip 25 Nm
¨ Pistol grip (SW 3 inner hexagon) 7 Nm
¨ Fastening screws 30 Nm
¨ Ermeto- hose screw joints DN20 -18L 100 Nm
(Co-axial hose)
Page | 14
Technical drawings
1. Impulse Gun IFEX 3001, assembly
11
2
5
16
13
10
12
15
Sheet
1.4301
A2
1.4301
St.
Burst disc with socket wrench
Forward support for shoulder strap
Rear support for shoulder strap
Special wrench for screwed cap
Diaphragm
1000004
1000007
1000021
1000003
13
4
14
18
16
17
Plastic
A2
985
Washer DIN 125
01000017
14
15
Muzzle with split diaphragm
Washer-Teflon
Shoulder strap
Screwed cap
Hexagon nut
01000016
01000014
01000008
111
3
2
11
12
13
Pistol grip w. trigger & locking dev.
01000009
01000012
1
8
7
9
10
High performance valve
Snap on air pressure connection
Front support grip
Water valve
01000040
01000015
1
1
1
1
6
5
3
4
Material
DIN
IF-3001-01
Part List
%
Scale
acc.
Description and type
Water barrel
Air power chamber
Surface
tolerance acc.
Dimension without
Art.-n°
IFEX Code
11
1
2
Hansestraße 18
Qty.
IFEX Technologies GmbH
Item
ASSEMBLY
IF-IG-3000-110
IMPULSE GUN IFEX 3001
IFEX Code:
1302
Name
DIN ISO
Breese
Breese
26.09.01
15.12.
Date
DIN 7168-m
1998
Drawn
Check.
Norm
Germany
D-27419 Sittensen
CAD4-Tetra\H:\HB-3012engl/Blatt15A
IFEX 3000
Technology
Extinguishing
Impulse Fire
Name
Date
Alteration
Index
OPEN CLOSE
3
Water connection
1
release
7
lock
Remark:
Order of spare parts:
Please use part list nos.
6
Gun trigger lock
Air pressure connection
IFEX 3000/1, Impulse Gun-compl.
NATO-STOCK NR.
VersNr. 4210-12-349 8251
13
15
9
12
Page| 15
2. IFEX 3072 Hose reel fire extinguishing unit, complete
16
IF-CO -3 0 0 0 3 0 - 3
Part of Nr. 27055
IF-HR-3 00 0 0 2 -1 0
IF-CO -3 0 0 0 0 7 - 8
IF-SL -3 0 0 00 6 - 6 ?2IF-SL -3 0 0 00 6 - 6 ?
IF-AC -3 00 008 -1 1
IF-RE -3 00 005 -2
IF-CO -3 0 0 0 0 7 -4 .1
IF-AC -3 00 008 -3
IF-SL - 3 0 0 0 0 6 - 5?
IF-H R-30 000 1-4
IF-HR-300001-2
IF-HR-300001-5
IF-HR-300001-1
IF-CY -3 0 0 0 04 -2/ 12
IF-RE -3 00 005 -5 -2
IF-T R -30 00 02-3
Dra wi ng- n °
Bla t t
Ursprung: Pr-17-2
3
7
22
72 li ter water container
Hosereel 55 m wi th rewind ha ndl e - left
Pressure regulator 300/7/25 bar compl.
1812 0
Mounting rack with sledge
Air cylinder 6 liter/200 bar with valve - steel
5400 1
2
Hosereel Equipment- left/55m hose compl. with
sledge, 72 l water container, air pressure bottles,
6500 9
2705 5
65000066
18000063
1
1
1
1
456
1
2
3
10
18
Water hose hose, assy.
Filt e r 3 /4 "
Manometer Ø 41, 0 - 10 bar, G 1/8"
Angle 1/4" i/a
Air pressure unit at hose reel unit
Labeling as per DIN EN3, Teil 5 - e nglish
0° C b i s + 60 ° C
Wasserventil
betätigen
betätigen
Lösch pis tol e
4.
2.
A
WASSER
FEUERLÖ SCHER
A
öffnen
Luftflasche n
1.
Ach tun g!
entsichern
Lösch pis tol e
3.
IFEX 3001/3550
Funktionsbe reich:
Typ :
Nr. der Anerkennung:
Telefon: (04282) 93060 Telefax: (04282) 930626
IFEX GmbH, Hansestrasse 18, D-27419 Sittensen
Tank nach jeder Betätigung neu füllen!
Was s e r
di e mi t de m a n e r k an n t e n M u s t er ü b e r ein s ti mme n .
2 x 6 Liter Druckluft 300 bar
Nur solche Lösch-/ Treib mi ttel und Ersatzteile verwenden,
besonders ge schultes Persona l.
Nicht auf Mensch oder Tier zielen;
Mindesta bstand 6 Meter; be i elektri schen
Löscher mi ndes t ens 1m al i m Jahr auf E insat zbe r eitsch aft üb er p rüfe n.
Einsatz nur du rc h die Feuerw eh r ode r
IFEX 300 0
Trei bmi t tel :
Löschm itte l:
Anlagen nur b is 1000V; Mindestabstand 1 Meter
Hinweise im H andbuch des Herstellers beachten.
Rewin d ha n d le
Ent leerung/
Draining
21
1
1
22
23
Coupl i n g with NR - 1/4 "
CO-axi al ho se 55 m , assy.
Imp u l s Gun 1 l i te r
Plug 1/2" - nickel plated
01001
6505 5
09000035
65000101
121
2
19
18
20
21
Red. pi e ce 1/4 " o u tside - 1/8" in sid e
27000007363000001
17
Air pressure hose, regulator-hose reel, assy.
18000055
6505 6
6505 7
2
1
1
16
13
14
15
Gerade Einschraubverschraubung 3/4" x L22
Air pressure ho se, assy.
6505 9
6505 8
1
1
11
12
Fill i ng un i t c o m pl .
Einstellbare Winkelverschraubung 22 L
650000 88
650000 41
650000 43
1811 0
1
111
2
9
7
8
10
16/17
23
IF-3000
%
Scale
Surface
Descript ion and T ype
regulator, hoses and impulse gun
Dimension without
Art.-n°
IFE X Co d e
Oty,
Pos.
- 55 m Hose co mp l. -
- Rewind handle left side-
H:/CAD4-Tetra/I fx 3072-En gli /B la t t 17
IFEX Cod e :
acc.
1302
Name
DIN IS O
Date
tolerance acc.
DIN 71 68 -m
2001
Germany
Han s e s t ra ß e 18
D-2 7 4 1 9 S it t en sen
IFEX Te ch n o l o g i e s G mbH
IF-3000-130
IFEX 3072 H os eree l Fire E xti ng uis hin g Unit
Breese
Breese
IFEX 30 0 0
26. 09 .
26. 09.
Drawn
Check.
Te c h n ol o g y
Im p ul se Fi r e
Ext i ng ui shi n g
No rm
Name
Date
Alteration
Ind ex
15
Order of spare parts:
Plea se use part l ist nos.
Ersa tzteilbestellung
nur mit Art. Nr.
11
8
9
12
4
Lub rication
Top of sle dge
Remark /emer k ung:
Drum br ake
Sled ge brake
Sled ge
Sledge raising 700 mm
Bear ing
19
Imp u ls Gun
14
"X"
6
Cone for rewinde hand le
13
5
Deta il " X "
IFEX 300 1 Impuls Gun
see IF-3000-130 sheet 16
20
Sto p p er
Pos. 1
Water hose
(Co -axi a l Ho s e)
Air pressure hose
19
Bearing
Sicherun gsw i nkel
Rack
Fa sten ing M 1 0
Page | 16
3. Hose reel, assembly (1)
2
508
595
1
70
IF-HR-30001-4-1
IF-HR-30001-4-2
IF-SL-300006-2-1
127 127127
CO-axial Hose 3/4"+1/4" Assy.
1/4" Air pressure swingjoint (Part at 1)
546
G1/4" Air
3
2
7
5
5
1
1
7
562
Rewind handle
3/4" Water swing joint (Part at 1)
65056
1
1
5
6
G1/8" Connection elbow with Plasticpipe
G1/2" Water Connection
1
1
1
3
4
2
Drawing-n°
Ursprung : H:/CAD4/IFEX/HR-002-5
IP-3100-1
%
Hosereel
Assembly
IF-3000-140E
Scale
IFEX Code:
acc.
1302
Name
DIN ISO
Surface
Description and type
Hosereel compl. with 55 m hose.
Mat. steel sheet red painted,
24V-E-electric rewind
27060
1
1
Dimension without
Art.-n°
IFEX
Code
Qty
IFEX Technologies GmbH
Item
Breese
Date
19.04.
DIN 7168-m
tolerance acc.
1999
Drawn
Check
Norm
Germany
Hansestraße 18
D-27419 Sittensen
H:/CAD-Tetra/Ifx3072-engl/IFX30100E
Technology
IFEX 3000
Impulse Fire
Extinguishing
Name
Date
Alterati on
Index
Greasenippel
6
G3/4"Water
19
190
4x boring Ø10,5
4
=
127 127127=489
3
- Lower (Rewind) position; Drum unbraked
- Middle (Braket) position; The brake is partially applied in order to
control the drum during deployment of the hose.
- Upper (Locked) position; The drum is fully applied. The position should be
selected during transit or when the hose is in use is a positive lock
on the drum is required.
2
1
3
Page | 17
4. Hose reel, assembly (2)
Altern. 9
10
2
IF-SL-300006-5
IF-SL-300006-6
IF-HR-300001-4
IF-SL-300006-2
Air pressure hose from reg. to hose reel compl.
Alt. pressure regulator 25/7bar compl.
8
65100
27151
1
1
9
Air connection
6
7
10
Quick snap on connection air
Pressure regulator 25 bar, ass.
27150
18000031
1
1
876
Adapter ¼" x 1/8"
Water hose ass. Impulse Gun - 510mm
Air pressure hose, ass. Impulse Gun
CO-axial hose 3/4"+1/4" ass.
without parts 4 and 5.
Hose reel (without hose)
Crank handle
70006
65055
70005
27000045
1
1
1
5
4
27000020
1
1
1
3
1
2
Drawing-n°
IF-HR-300001-4
IP-3100-1
%
Scale
acc.
Surface
tolerances acc.
Dimensions without
metal sheet red painted
Description and type
Hose reel complete up to 55 m hose
metal sheet red painted, crank handle left side
Art.-n°
27055
IFEX
Code
1
1
Hansestraße 18
Oty
IFEX Technologies GmbH
Pos.
Hose reel,assambly
IFEX Code:
1302
Name
DIN ISO
Breese
26.10.
Date
DIN 7168-m
Drawn
2001
Check
Germany
D-27419 Sittensen
IF-3000-130-1
IFEX 3000
Technology
Impulse Fire
Extinguishing
Norm
Date Name
Alterat ion
Index
3
1
4
right mirrow image
drawn left
crank handle
Pivot for
Grease nipple
Water connection 3/4
5
Page | 18
5. Mounting rack with sledge, assembly
Air
pressur e
connection
Lubricat i o n
Drum b rake
IF-TR- 3 0 0 0 0 2 -1
IF-HR-3 0 0 001 -2 -1
4
Air cyl. ho ld er ( 2 x 6 l )
Mounting s tra ps f or air cylinde r
View A
2
3/4Fi lter
Wate r c on n e ct ion
Cone for rewind handle
Sladge
Dru m brake
A
Slide bearing
Sladg e br ak e
Sledge racing 700 mm
Sladg e bra ke
Sh a ft for ha ndle
Greas e
6. 0 l/ 200 b ar A ir p r. C y linder (S t.)w . valv e
54001
65006
2
2
1
5
6
7
Hose r eel 55m with r ewi n d han dl e-lef t
27055
1
Drawing-n°
IF-HR-3 00 0 0 1 -1
IF-HR -3 00 001 -2
IF-3000
1:5
IFE X Cod e :
Scale
IFEX 3072 M ounting rack with
sled ge - Assembly
acc.
1302
Name
DIN I SO
Surface
Breese
Description and type
IFE X 307 2 M o u nt i n g r a c k w i th s l adge
72 lt r . w ater c ontainer
IFE X 30 7 2 com p l . H o s ere e l un i t 5 5 m
65009
Dimension without
6500006 6
180000 63
Art. -n°
IFEX Code
1
1
1
Oty
1
2
3
4
Item
Sladg e brak e
Breese06.11.01
Date
12.04.
DIN 7168-m
toleran ces acc .
1999
Dra wn
Norm
Check
Germ an y
Hans es t raße 1 8
D-27419 Sittensen
IFEX Technologies GmbH
Sladge after compl.
Ursp run g : H: / CAD4 /I FE X/ HR/ HR- 00 2-4
IF-3 00 0-1 30
H:/ C A D 4 / Ha n d bu c h 30 7 2 -e n g l /
IFEX 3 0 00
Te ch no l o gy
Im pu l se F i re
Extinguishing
Date Name
Alteration
Index
galvanized
4
Pos. 1
Stopper
5
4
Cyl ind er
Air pre ss u re
6
2
7
Sc r e w M8
Water cylinder
fastening
3
Sid e vi ew
bar
8
72
XX
XXXX
IFEX
CYLI NDER 30 72
TEST P RES S. 1 0. 4 bar
Baujahr
zul. Betr.- Über
Inhalt
Fabr.- Nr.
Baum .
TYP
Bearing
Protec tion
angle
Screw
M8 Grund-
gestel l
Befestig ung
3
49
Page | 19
6. Top Filling unit and filter, IFEX 3001/72
1. Top filling unit assy.
1.6
1.2
1.1
1.5
Body made of brass
1.4
R 2"
1.3
Remark
Order of spare parts:
Please use pa rt list n°.
1.5
1
1
1.4
1.3
1
1.2
1
1.1
1
IFEX Code
Oty.
Pos.
IFEX Te chn o log ies GmbH
Hansestraße 18
D-27419 Sittensen
Germany
18000032
18000041
09000013
18000040
09000033
Art.- n°
Dimensions with out
tolerance s acc.
DIN 71 68-m
1996
Drawn
Check
Norm
Alter ation
Inde x
Date
Name
Handle for top f ill ing unit, aluminium
O-Ring seal Ø53x5
Scew for handle SW13
Quic k coupling with relief valve
Safety valve 1/4"-6 bar
Description and type
Surface
acc.
DIN ISO 1302
Date
05.08.
IFE X 300 0
Impulse Fire
Extinguishing
Technology
Name
Bree se
IF-TR-300021-4A
IF-TR-300002-3B
IF-BP-300002- 3B
Drawing-n°
Scale
IFEX Code:
%
IF-3 000
IFEX 3035 und 3050 Trolley ,
IFEX 3072 Skid
Instruction for test and refilling
1. Top filling unit
IF-3000-130
Page | 20
IFEX
Technologies
GmbH
Hansestr. 18
27419 Sittensen
Extinguisher test date:
Maintenance and test certification
IFEX 3000 IMPULSE FIRE EXTINGUISHING
TECHNOLOGY
Maintenance record for
IFEX 3001/72
Fire Extinguishing Equipment
Maintenance record
Expert:
Nr.: IF3000-110
Page: 21
Date: 15.11.12
Maintenance record
Extinguisher test date:
Expert:
Maintenance record
Extinguisher test date:
Expert:
Page | 21
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Appendix A
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 1
Appendix A/ Tests
1. Testing the extinguishing agent container (by an expert)
The air pressure cylinder needs to be checked by an expert as per directive 2009/104/EC:
· external check – every 2 years
· internal check – every 5 years
· pressure test – every 10 years
Reduce the pressure in the container and emty the container completely. Disconnect all
fittings except the air pressure fitting and close the connections. Remove the safety valve
from the filling unit and close the connections. Fill the container with water through the
filling opening and close the filling unit. Fill the container with 10,4 bar through the air
pressure connector. Check the pressure by a test manometer. The pressure must be held
for 10 minutes. Emty the container and remount the fittings after testing.
Enter results of test in maintenance record Appendix A page 2.
2. Testing the air pressure container of the Impulse Gun (by an expert)
The air pressure container needs to be checked by an expert as per directive
2009/104/EC:
· external check – every 2 years
· Pressure test – every 10 years
Remove the bursting disc or safety valve and close the opening with a cylinder screw.
Connect the air pressure hose from the pressure source via a pressure regulator. The
pressure regulator must supply a secondary pressure of 60 bar to the air pressure
coupling of the gun. Put the Gun in a water basin, slowly open the valve at the pressure
source, observe the manometer and close the valve as soon as the pressure is 60 bar.
This pressure must be held for 30 seconds. After testing re-install the bursting disc or
safety valve.
(TÜV-bursting test at 03.02.96, Pall=45 bar, V= 0,8l, P
P
Wert = 60,0 bar)
Test
= 58,5bar),TÜV agreed rounded
Test
Appendix A Page | 1
(TÜV= German Technical inspection authority)
Enter results of test in maintenance record Appendix A page 3.
3. Tests according to national regulations for extinguishing agent container 72l
User
Invoice address
Place of use
Test certification as per
directive 2009/104/EC
Extinguishing agent container IFEX 3012
- Out of order
Cert. pressure: 13,0 bar
- Inside test
- Pressure test with water
- other test
Test pressure:
- Reg. every 10 years
19 bar
Type Nr.: IFEX 3072 Skid
Serial-Nr.: ___________
Constr. date: _____________
Type approv.: / TÜV
Volume: 72 Liter
Use: Fire exting. agent container
Test result
Deficiencies:
no
minor
major
dangerous deficienies
Notes:
Futher use is:
No problem.
No problem, if faults are adjusted.
(Place)
Expert
,Date
Not advisible.
We will notify the appropriate
authority.
Next regular inside test _____________
Next regular pressure test _____________
IFEX 3000 Impulse Fire Extinguishing Technology
Nr.: IF3000-110
IFEX
Technologies
GmbH
Hansestr. 18
D-27419 Sittensen
Extinguishing Agent Contai ner 72 Liter
Directive 2009/104/EC
Appendix A
Page: 2
Date:22.11.12
Appendix A Page | 2
4. Tests according to national regulations for air pressure chamber of Impulse Gun
User
Invoice address
Place of use
Test certification as per
directive 2009/104/EC
Extinguishing agent container IFEX 3012
- Out of order
Cert. pressure: 45,0 bar
- Inside test
- Pressure test with water
- other test
Test result
Deficiencies:
Test pressure:
no
60 bar
- Reg. every 10 years
minor
Type Nr.: IFEX 3001
Serial-Nr.: ___________
Constr. date: _____________
Type approv./ TÜV:07/95/0016
Volume: 0,8 Liter
Use: Fire exting. agent container
major
dangerous deficienies
Notes:
Futher use is:
No problem.
No problem, if faults are adjusted.
Not advisible.
We will notify the appropriate
authority.
(Place)
Expert
IFEX
Technologies
GmbH
Hansestr. 18
D-27419 Sittensen
,date
Next regular inside test _____________
Next regular pressure test _____________
IFEX 3000 Impulse Fire Extinguishing Technology
Directive 2009/104/EC
Gun Air Power Chamber
Nr.: IF3000-110
Appendix A
Page: 3
Date:22.11.12
Appendix A Page | 3
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Appendix B
Instructions for Use and Operation
Instruction Manual
Page | 1
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Appendix B/ fitting and maintenance
1. Introduction
Part „B” provides information for the operation of the reel, maintenance and basic repairs, as
well as spare parts. Regular maintenance assures ease of use of the unit. Should you have
any further questions, please contact your local IFEX dealer or IFEX Technologies GmbH in
Sittensen, Germany. This manual refers to the manual rewind hose reel as a part of the IFEX
3072 fire extinguishing unit. The fire extinguishing unit IFEX 3072 consists of the following
main components: sliding skid frame with a basic frame with sliding skid plus air cylinders
mounted with:
- Hose reel with 55m hose.
- extinguishing agent container 72 litre content.
- 2 air cylinders; 6 l/200 bar
- Air pressure hose unit consisting of 2 pressure regulators and hoses.
- Co-axial hose unit 55 m.
- IFEX 3001 Impulse Gun.
Refer to components of the IFEX 3072 Fire Extinguishing Unit manual page 16.
Mounting the IFEX 3072 unit
The skid with the mounted components can be raised onto the front of the vehicle where it
can be mounted.
Hose reel
The hose reel is powder coated /colour red RAL 3000 according to BS 381C538. The hose
reel with the other components on the sliding skid is supplied by IFEX Technologies GmbH
ready fitted.
The hose reel is the first component mounted on the skid in the direction of the extraction.
The rewind device is usually on the left side, the brake is on the right front side (custom
made skids with right side rewind devices can be supplied on order).
The grease nipple for the bearing is on the right on left front side of the reel.
Please note
The fire extinguishing unit with sliding skid can be removed from the
Appendix B Page | 1
vehicle for a more detailed maintenance. Refer to manual page 16.
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Appendix B
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
Instruction Manual
Page | 2
2. Routine maintenance
Every 6 months: (regular operating conditions). Lubricate the drum bearings and the spindle
of the rewind mechanism with general purpose grease through the grease nipples. Release
the brake and check the reel for easy rotation.
3. Operation of the drum brakes
a) Lower (rewind) position:
The drum is unbraked.
This position should be selected when the hose is being rewound.
b) Middle (braked) position:
The brake is partially applied. This position will allow a control of the drum during
unwind of the hose. This position will prevent the drum from rocking excessively when
the pressure is turned on and off.
c) Upper (locked) position:
The brake is fully applied. This position should be selected during transit or when the
hose is in use if a positive lock on the drum is required.
4. Brake adjustment
Move the brake lever to the lower rewind bottom position.
Apply pressure to the end of the brake rod. Sufficient pressure must be applied to
compress the spring and move the nut on the end of the rod clear of the brake shoe, so
that the nut can be rotated. Rotate the nut (clockwise when viewed from the back of the
reel to increase braking and anti-clockwise to decrease braking). The adjustments should
be made a little at a time. After each adjustment, move the brake lever to the braked
(middle) position and test the effectiveness of the brake. Repeat the operation until the
desired effect is achieved.
5. Rewind problems
If it should be difficult to rewind the hose to the reel, check the following:
Check that the hand wind brake is released. The brake should be in the lower (rewind)
position. Check that the drum bearings are lubricated, apply grease to the nipples.
If the drum is still tight, it is probably because the frame is mounted with a „twist“ in it. Try
loosening the bolts which fasten the reel down and if necessary put a packing piece
under one corner of the frame when re-tightening.
If the reel has been damaged during operation or otherwise, please contact your local
IFEX dealer or IFEX Technologies GmbH Sittensen, Germany.
Appendix B Page | 2
IFEX Technologies GmbH IFEX 3000 Impulse Fire Fighting Technology N°: IF3000-130
Appendix B
Instructions for Use and Operation
Hansestraße 18, 27419 Sittensen
Type IFEX 3072 Fire Extinguishing Unit with hose reel Date: 30.11.12
6. Leaky rotating swing joint- 3/4” water
When the reel is properly installed and maintained the rotating swing joint will have a
long life. Premature wear can occur if the joint is subjected to external strain from the
inlet connection. The connecting pipe must be flexible and should be fitted without
exerting any force on the rotating joint.
If the rotating joint should leak, replace the seals.
A self contained rotating swing joint is fitted externally. It can be serviced in-situ and can
be replaced without dismantling the hose reel.
6.1. Replacement of the rotating swing joint- 3/4” seal
Refer to IF-HR-300001-4-1.
Instruction Manual
Page | 3
Please note the caution notice: Manual
test and filling instructions Nr. IF3000-130 page 7.
Equipment needed: - external circlip pliers
- plug-Ø 2 mm, setting 7 - 20 mm
Seal: - two nitril seals Nr. 0216.00T
Procedure: Empty co-axial hose. Disconnect the water hose from the rotating swing joint.
Remove the circlip and the washer from the end of the hose fitting and pull off the sleeve.
Remove the seals from the socket (pick them out with a sharp tool, but take care not to
scratch the bottom of the groove where the seals fits).
Wipe all the parts clean, fit new seals into the grooves and the socket to the hose fitting.
Fit the washer and re-mount the circlip. Fit the water hose to the rotating swing joint.
If leakage still occurs after replacing the seals, it is possible that the rotating joint is worn
and may need to be replaced. In this case please contact your local IFEX dealer or IFEX
Technologies GmbH Sittensen, Germany.
Appendix B Page | 3
Technical drawings
1. Sliding skid, support for air cylinders
3. Support for air cylinder
A - A
Ø5,2
R75
70
20
welding
3.1
50
3.6
3.2
5 x 45°
Ø10
A
3.7
welding
85
180
40
A
3.3
3.4
60
5
46
3.5
405
tack-welding
5
110
140
After completion
coating with
colour RAL 3000
weight: 4,2 kg
4
3,7
2
3,6
2
3.5
3.4
4
2
3.3
3.2
2
3.1
1
3
1
IFEX Code
Oty.
Pos.
IFEX Technologies GmbH
Hansestraße 18
D-27419 Sittensen
Germany
18000052
65000001
Art.-n°.
Drawn
General
tolerance acc.
ISO 2768 mK
1999
Check
Norm
countersink screw M5x15 with nut ss AISI 316
mounting strap for air cylinders compl.
sheet metal 40 x160 x 3
sheet metal 60 x 50 x 5
sheet metal 40 x 5 x 400 lg.
pipe 139,7 x 4,5 x 50
sheet metal 485 x 140 x 50
support for air cylinder, complete
Description and type
Surface
acc.
DIN ISO
1302
Date
12.04.
Name
Breese
455
485
DIN 965/985
IF-TR-300002-1
IF-HR-300001-2-1
Dawing-n°
Scale
IFEX Code:
%
IF-3000
IFEX 3072 Sliding skid
Support for air cylinders
Index
Alteration
Date
Name
IFEX 3000
Impulse Fire
Extinguishing
Technology
IF-HR-300001-2-1
Skid Att. B page 4 HR-002-1
Page 4
Appendix B Seite | 4
2. Sliding skid, base frame
B - B
1.7
1.6
35
15
Drawing-N°
DIN 965/985
ø15
ø17
1.5.2
1.5.1
40
Part 1.5
40
40
120
580
1.8
Ø 10
Part 1.8
90
20
Ø17
34
50
1.5.2
II
1.5.3
15
60
34
Srews M6x 12
Shaft
Skid slide bearing
Roller bearing Ø15 xØ35 x 11
Securing angle 50 x 50 x 5 x 120 long
Countersink screw M8x15 with nut
1
1.8
1.9
Plate 40 x 35 x 12
Locking bolt for skid
65000157
2
2
2
2
228
1.5
1.6
1.7
1.5.1
1.5.2
1.5.3
IF-HR-30000-1-2-2
IF-3000
%
Scale
IFEX Code:
acc.
1302
DIN ISO
Flat steel50 x 60 x 5
Flat steel 30 x 25 x 8
65000156
2
2
1.4
1.3
Surface
Description and type
Plate 470 x 70 x 4
Plate 1135 x 140 x 4
Skid, base frame
tolera nce a cc.
DIN 7168-m
Dimension without
Art.-n°
65000156
IFEX Code
1
2
2
1.2
Hansestraße 18
D-27419 Sittensen
Oty.
IFEX Technologies GmbH
1
1.1
Pos.
Page 5
HR-002-2
IFEX 3072 Sliding skid
base frame
IF-HR-300001-2-2
Skid Appendix A Page 5
Name
Breese
Date
12.04.
1999
Drawn
GERMANY
Technol ogy
IFEX 3000
Impulse Fire
Extinguishing
Norm
Check .
Name
Date
Alteration
Index
Part 1.3
Ø 7
to weld
1.6
610
540
470
70
II
305
A
1.5
135
60
140
35
70
galvanized
After completation
B
1.1
1.3
" X "
1.2
25
" X "
30
335
1.4
1.4
1.7
B
1135
395
edging line
1135
A - A
t = 4 mm
1 - Skid, base frame
1.2
II
70
Ø10 Drills for M8 fixing screws
1.8
1.9
All drills Ø10
500
II
Ø10
sagging from underneath
90
334
35
20
560
230
49
A
edging line
1.1 sheet metal bevor edging
Appendix B Page |5
3. Water connection at hose reel
71
KS 36
G3/4"
48
75
G3/4"
1
Appendix B Page | 6
1
1
IFEX
Oty.
Pos.
Index
Code
IFEX Technologies GmbH
Hansestraße 18
D-27419 Sittensen
Germany
Alteration Date
FPC.109
Art.-n°
Name
Circlip
Description and Type
General
tolerance acc.
ISO 2768 mk
1999
Drawn
Check.
Norm
Date
19.04.
Surface
DIN ISO
1302
Name
Bre
IFEX 3000
Impulse Fire
Extinguishing
Technology
acc
Drawing-n°
1:1
Scale
IFEX Code:
IF-3072
3/4" Water connection
at hose reel
(belongs to scope of reel supply)
3/4" Swing joint - water conn. at hose reel
IF-HR-30001-4-1
Skid Appendix B Page 7
HR-002-6
7
4. Air connection at hose reel
Circlip
74.5
G1/4"
35
G1/4"
KS 28
Art. N°: 7512.00.M-1/4
IFEX Technologies GmbH
Hansestraße 18
D-27419 Sittensen
Germany
General
tolerance acc.
ISO 2768 mk
Date
1999
Drawn
19.04.
Check
Norm
Index
Alteration
Date
Name
Appendix B Page |
Surface
acc.
DIN ISO
1302
Name
Bre
IFEX 3000
Impulse Fire
Extinguishing
Technology
Scale
IFEX Code:
1:1
IF-HR-3072
1/4" Swingjoint - Air conn. at hosereel
(belongs to scope of reel supply)
IF-HR-30001-4-2
Skid Appendix B Page 8
HR-002-7
be submitted immediately following discovery of the fault to the sales partner or to IFEX
warranty claim. In this respect it is always sufficient for the affected product to fulfill the test requireme
new reconditioned parts. If
Warranty
________
_____________________________________________________________________________________________________
IFEX Technologies GmbH grants a warranty for the product purchased by the customer for a period of 24
months after purchasing.
The following information details the terms of the warranty offered by IFEX Technologies GmbH. You are
entitled to make a claim under this warranty in the event of any manufacturing or material defects on the
product you have purchased. The warranty provided is based on a voluntary obligation of IFEX Technologies
GmbH as the manufacturer. It only applies to end customers. No warranty rights other than those expressed
herein, whether given by IFEX Technologies sales partners or third parties, can be asserted against IFEX
Technologies GmbH.
The warranty begins on the day of purchase stated in the invoice. Please note that warranty claims can only be
processed if accompanied by the original invoice in combination with the approval certificate of the product.
Therefore, always keep the invoice and the approval certificate together with the warranty documents.
The invoice must show the type of the product and the serial number.
Warranty claims must
Technologies GmbH.
Please check the availability of the sales partner in the documents given to you by the sales partner. IFEX
Technologies GmbH is available by phone: +49 (0) 4282/ 9306-0, by fax: +49 (0) 4282/ 9306-26 or by e-mail at
info@ifextechnologies.com.
After consulting IFEX Technologies GmbH the customer should return the defective product to IFEX
Technologies GmbH.
In the event of a warranty claim IFEX Technologies GmbH will pay the costs for the resulting labour and any
required materials or replacement parts.
The costs of the transport to and from IFEX Technologies GmbH will be accounted separately, without the
common additional charges net/ net.
The warranty is limited to restoring the performance features and condition of the original product prior to the
nts in
accordance with the IFEX Technologies specifications for the original product. The warranty is fulfilled at the
discretion of IFEX Technologies GmbH either by repairing or replacing the defective device. In cases of material
and/ or processing defects, defective parts shall be replaced with new or as necessary, the complete product should be exchanged for an identical product or an alternative product offering
the same level of functionality. The value of the warranty service is always limited to the value of the defective
product.
The defective parts removed or replaced from a product during the course of warranty action shall become the
property of IFEX Technologies GmbH.
Genuine IFEX Technologies parts installed under warranty in an IFEX Technologies product are only covered
by the remaining duration of the warranty of the overall device.
Warranty exclusions
Defects caused by improper use are excluded from the warranty. Improper use of the equipment is taken to be
The warranty is rendered null and void if:
Limitation of liability
warranty conditions are excluded. This also applies in particular with regard to claims
to compensation for
Applicable law
with the said laws.
any operation of the product under conditions which do not meet the terms of proper use described in the
operating manual or documentation of the product.
The warranty also does not cover the following points:
Wearing parts and consumable materials
Diagnosis and rectification of defects caused by improper use or improper maintenance of the
device by the customer or third parties. Improper actions include operations that are not
compatible with the instructions contained in the product manual.
Force majeure (lightning strike, floods, war etc.)
Dirt, seals or stickers
Any other circumstances for which IFEX Technologies cannot be held responsible.
IFEX Technologies products are operated or fitted with parts, components or peripherals which
have not been approved for that purpose by IFEX Technologies GmbH.
The device is covered with irremovable seals, stickers or similar.
The original warranty sticker at IFEX Technologies products is damaged or removed
respectively if manipulations at those stickers are apparently.
Services/ repairs or other changes to the product are carried out by persons who have not been
authorized by IFEX Technologies GmbH to carry out such work.
This clause is not valid if the customer can prove that any defects were neither caused by nor arose as a
consequence of such events.
Any claims of the party entitled to the warranty which exceed the scope of terms expressly mentioned in these
subsequent damages, loss of profits, data losses or information losses or damages following of the inoperability
or missing of the product due to maintenance or repair.
The warranty is subject to the applicable laws in the country of purchase and is to be interpreted in agreement
Rev. 001/ 01 2011
LOSS OF GUARANTEE!
IFEX 30002/72
FIRE EXTINGUISHING UNIT WITH
HOSE REEL
ATTENTION!
ANY UNAUTHORIZED ALTERATION TO
THE EQUIPMENT WOULD RESULT IN
LOSS OF APPROVAL AS WELL IN
IFEX Technologies GmbH, Hansestr.18, D-27419 Sittensen
Telephone: +49 (0) 4282 93060 Fax: +49 (0) 4282 93026
Homepage: www.ifextechnologies.com
e-mail: info@ifextechnologies.com
Loading...