IER 420RFID 12 User Manual
IER i420
N0L8S2A6 P1
October 2, 2019
PROVISOIRE
PRINTER
USER SAFETY AND START GUIDE
IER i420
User Safety and Start Guide
Ce document est la propriété d'IER et ne doit pas être reproduit ou communiqué sans autorisation écrite
This document is the property of IER and may not be reproduced or communicated without prior written authorization.
Page 2
N0L8S2A6 P1
1. I420-220 PRODUCT TESTED AT 230 V, 50HZ, FOR EC MEASUREMENTS
This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause
radio interference.
This symbol on the equipment indicates the presence of an RFID module
Module
Manufacturer
Model
Frequency
Effective Radiated Power
RFID
Impinj
RS500-EU
865 to 868 MHz
+1.32 dBm
Module
Manufacturer
Model
Frequency
Effective radiated power
RFID
Impinj
RS500-GX
902 to 928 MHz
+23 dBm
PROVISOIRE
COMPLIANCE STATEMENT FOR EUROPEAN USERS
CE marking shows conformity to the following criteria and provisions:
Low Voltage Directive (2014/35/EU)/EN60950-1
EMC Directive (2014/30/EU)/EN55032, EN55024, EN61000-3-2 & EN61000-3-3
The i420-220 version of the equipment may be fitted with radiating modules as indicated in the table here after:
GS MARK STATEMENT
This product has been tested under EN ISO 7779 and has an acoustic level output no higher than 55db (A).
This device is not intended for use at a video workstation in compliance with Bildscharb V.
This device is not intended for use in the direct field of view at visual display workplaces. To avoid incommoding reflections at visual
display workplaces this device must not be placed in the direct field of view.
2. I420-120 PRODUCT TESTED AT 120 V, 60HZ, FOR FCC AND ICES MEASUREMENTS
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
This equipment complies with FCC’s radiation exposure limits set forth for an uncontrolled environment under the following conditions:
1. This equipment should be installed and operated such that a minimum separation distance of 20 cm is maintained between the
radiator (antenna) and user’s/nearby person’s body at all times.
2. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The i420-120 version of the equipment may be fitted with radiating modules as indicated in the table here after:
EMI COMPLIANCE STATEMENT FOR CANADIAN USERS
This Class A digital apparatus complies with Canadian ICES-003.
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to radio and television reception. This digital apparatus does not exceed the
Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications. This equipment is designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Use shielded cables to connect this device to computers.
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the
equipment.
ETAT DE CONFORMITE EMI A L’USAGE DES UTILISATEURS CANADIENS
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Cet équipement produit et utilise l’énergie à radiofréquences et s’il n'est pas installé et utilisé correctement, c’est à dire en accord
strict avec les instructions du fabricant, il risque de provoquer des interférences avec la réception de la radio et de la télévision.
Le présent appareil numérique n’émet pas de bruits radio électriques dépassant les limites applicables aux appareils numériques de
la classe A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
Cet équipement est conçu pour fournir une protection satisfaisante contre de telles interférences dans une installation résidentielle.
Cependant, il n’y a pas de garantie contre les interférences avec les réceptions radio ou télévision, provoquées par la mise en et hors
circuit de l’équipement; aussi, il est demandé à l’utilisateur d’essayer de corriger l’interférence par l’une ou plus des mesures
suivantes:
• Réorienter l’antenne de réception.
• Installer l’ordinateur autre part, par égard pour le récepteur.
• Brancher l’ordinateur dans une prise de courant différente de façon à ce que l’ordinateur et le récepteur soient branchés sur des
circuits différents.
IER i420
User Safety and Start Guide
Ce document est la propriété d'IER et ne doit pas être reproduit ou communiqué sans autorisation écrite
This document is the property of IER and may not be reproduced or communicated without prior written authorization.
Page 3
N0L8S2A6 P1
IC
PROVISOIRE
This equipment complies with RSS102’s radiation exposure limits set forth for an uncontrolled environment under the following
conditions:
1. This equipment should be installed and operated such that a minimum separation distance of 20cm is maintained between the
radiator (antenna) and user’s/nearby person’s body at all times.
2. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Cet équipement est conforme aux limites d’expositions de la CNR102 applicables pour un environnement non contrôlé aux conditions
suivantes :
1. Cet équipement devra être installé et fonctionner de telle manière qu’une distance minimale de séparation de 20 cm soit maintenue
entre la partie rayonnante (l’antenne) et l’utilisateur / les personnes à proximité à tout moment.
2. Cet émetteur ne doit pas être co-localisé ou opérer en conjonction avec toute autre antenne ou émetteur.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
IMPORTANT SAFETY INSTRUCTIONS
Read all of these instructions and save them for later reference.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product.
Slots and openings on the cabinet and the back or bottom are provided for ventilation.
To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. The openings
should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near
or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided.
This product should be operated from the type of power source indicated on the marking label.
If you are not sure of the type of power available, consult your dealer or local power company.
This product is equipped with a three-pronged plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
Do not allow anything to rest on the power cord. Do not locate this product where the cord will be walked on.
If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the
extension cord do not exceed the extension cord ampere rating. Also, make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes for 120V outlet and 7.5 amperes for 220V-240V outlet.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.
Except as explained elsewhere in this manual, don't attempt to service this product yourself. Opening and removing those covers that
are marked "Do Not Remove" may expose you to dangerous voltage points or other risks. Refer all servicing on those compartments
to service personnel.
The mains plug on this equipment must be used to disconnect mains power. Please ensure that the socket outlet is installed near the
equipment and shall be easily accessible.
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating a need for service.
This appliance must be connected to protection earth.
DANSK: Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord.
NORSK: Apparatet må tilkoples jordet stikkontakt.
SVENSKA: Apparaten skall anslutas till jordat uttag.
SUOMALAINEN: Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan.
Loading...