IER 400 UHF04 User Manual

USER SAFETY GUIDE

THIS PRODUCT COMES WITH A LITHIUM BATTERY. BATTERY REPLACEMENT MUST IMPERATIVELY
BE PERFORMED BY QUALIFIED MAINTENANCE PERSONNEL. MOREOVER, ONLY IER APPROVED
MODELS MAY BE USED.

DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE
SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED
BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

DO NOT OPEN THE POWER SUPPLY UNIT CASE FOR ANY REASON, SINCE HIGH VOLTAGE MAY BE
PRESENT.
DO NOT REPLACE THE FUSE OF THE POWER SUPPLY UNIT.

The United States Federal Communications Commission (in 47 CFR 15.105) has specified that the following
notice be brought to the attention of users of this product.

: This equipment has been tested and found to comply with the limits for a Class B digital device,

NOTE
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to w hich the re ceiver is conne cted.

- Consult the dealer or an experienced radio/TV technician for help.
In accordance with FCC requirements, changes or modifications not expressly approved by IER

could void the user's authority to operate this product.
Use of a shielded cable is required to comply within Class B limits of Part 15 of FCC Rules.

NORWAY
voltage 230V.

NORWAY & SWEDEN

THIS PRODUCT MUST EXCLUSIVELY BE CONNECTED TO AN ELECTRICAL CIRCUIT THAT IS

- PROVIDED WITH A GROUND FAULT CIRCUIT INTERRUPTER (GFCI) COMPLYING WITH

- CONFORMING WITH THE VOLTAGE CHARACTERISTICS SPECIFIED BY THE NF EN 50160 STANDARD.

The cover(s), and/or door(s) of this product is (are) intended for occasional use and must be normally closed.

: This product is also designed for IT power distribution system with phase-to-phase

: Apparaten skall anslutas till jordat uttag när den ansluts till ett nätverk.

THIS APPLIANCE MUST BE GROUNDED.

IEC 364 AND NFC15-100 REGULATIONS, AND

WARNING

ENGLISH

In compliance with the European Directive 2002/96/CE relative to the management of Waste Electrical and
Electronic Equipment (WEEE) implemented as of August 13, 2005, this product may not be disposed of with
regular household waste. All products concerned by this directive are marked with the above symbol.
The end owner of this product is responsible for either:

• Transferring the product to an authorized treatment facility where the product components, recognized to
present a hazard to the environment and/or public health, will be recycled and recovered properly, or

• Consulting with the manufacturer for appropriate product waste management according to the terms of the
manufacturer.

The information and specifications contained in this document are subject to change without prior notice.

IER 400

N0C4SEA2

OPERATING CONDITIONS AND ELECTRICAL CHARACTERISTICS
Environmental Conditions

Operating Temperature.........................................................................................+5°C (41°F) to 40°C (104°F)

Storage Temperature............................................................................................-20°C (-4 °F) to 60°C (140°F)

Relative Humidity........................................................................................20% to 80%, without condensation

Operating Environment....................................................................................................... Fully enclosed area

(airport lobby, railway station, travel agency, etc.)

Power Requirements

Line Voltage............................................................................................................. Authorized voltage ranges

100-120 Vac / 60 Hz / 1.6 A
200-240 Vac / 50 Hz / 0.8 A

CONNECTION TO THE LINE VOLTAGE / POWER UP
Connecting to the Line Voltage

Connect the AC power cord first to the AC power connector on the IER
product (see illustration opposite) and then to the AC power outlet.

Powering Up Set the power switch to the I position (see illustration opposite).

POWERING DOWN / MAKING THE IER PRODUCT ELECTRICALLY SAFE
Powering Down
Set the power switch to the 0 position (see illustration opposite).

Making the IER Product Electrically Safe

Disconnect the AC power cord from the AC power connector of the IER
product.

IMPORTANT: Visit our website to read and/or download the Installation and User

Documentation corresponding to your IER product:

www.ier.fr