IEI Technology VTT-1000 User Manual

V

VTT-1000 Vehicle Tracking Terminal

MODEL:

VTT-1000

ehicle Tracking Terminal with Touchscreen

ARM9 400 MHz CPU, USB, Audio, DIO, RS-232,

RoHS Compliant, IP 54 Protection

User Manual

Rev. 2.00 – June 12, 2015

Page i

Date Version Changes

June 12, 2015 2.00 Updated for R20 version

April 14, 2011 1.00 Initial release

VTT-1000 Vehicle Tracking Terminal

Revision

Page ii

VTT-1000 Vehicle Tracking Terminal

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to

improve reliability, design and function and does not represent a commitment on the part

of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

Copyright

reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification

purposes only and may be trademarks and/or registered trademarks of their respective

owners.

Page iii

VTT-1000 Vehicle Tracking Terminal

Table of Contents

1 INTRODUCTION.......................................................................................................... 1

1.1 OVERVIEW.................................................................................................................. 2

1.2 FEATURES................................................................................................................... 2

1.3 FRONT PANEL............................................................................................................. 3

1.4 SIDE PANELS .............................................................................................................. 4

1.5 BOTTOM PANEL.......................................................................................................... 4

1.6 REAR PANEL...............................................................................................................5

1.7 SYSTEM SPECIFICATIONS............................................................................................ 6

1.8 DIMENSIONS............................................................................................................... 8

2 UNPACKING ................................................................................................................. 9

3 INSTALLATION ......................................................................................................... 12

3.1 ANTI-STATIC PRECAUTIONS...................................................................................... 13

3.2 INSTALLATION PRECAUTIONS................................................................................... 13

3.3 INST ALLATION AND CONFIGURATION STEPS............................................................. 14

3.4 SIM CARD INSTALLATION........................................................................................ 14

3.5 MICROSD CARD INSTALLATION................................................................................ 15

3.6 MOUNTING THE SYSTEM (OPTIONAL) ...................................................................... 16

BOTTOM PANEL CONNECTORS ................................................................................. 19

3.7

3.7.1 Digital I/O and RS-232 Connection................................................................. 19

3.7.2 RS-232 Connection .......................................................................................... 20

3.7.3 Power Input Connection.................................................................................. 21

3.7.4 USB Device Connection................................................................................... 21

3.8

POWER-ON PROCEDURE........................................................................................... 22

3.8.1 Installation Checklist....................................................................................... 22

3.8.2 Power-on Procedure ........................................................................................ 23

3.9 SYSTEM MAINTENANCE........................................................................................... 24

3.9.1 Software ........................................................................................................... 24

3.9.2 Hardware ......................................................................................................... 25

4 APPLICA TION TOOLS ............................................................................................. 26

Page iv

VTT-1000 Vehicle Tracking Terminal

INTRODUCTION......................................................................................................... 27

4.1

4.1.1 VTT_UTILS...................................................................................................... 27

4.1.2 Register Utils ................................................................................................... 27

5 SDK ............................................................................................................................... 28

5.1 INTRODUCTION......................................................................................................... 29

5.2 DEMO APPLICATION ................................................................................................. 29

5.3 VTT-1000 API......................................................................................................... 29

5.3.1 Digital I/O API................................................................................................. 30

5.3.2 COM (Serial) Port API.................................................................................... 30

5.3.3 Temperature API .............................................................................................. 31

5.3.4 Programming Key API..................................................................................... 31

5.3.5 E-Compass API................................................................................................ 32

5.3.6 G-Sensor API................................................................................................... 32

6 INTERFACE CONNECTORS................................................................................... 34

6.1

PERIPHERAL INTERFACE CONNECTORS..................................................................... 35

6.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 36

6.2.1 3G Module Connector (CN6)........................................................................... 36

6.2.2 LCD Connector (LCM1).................................................................................. 38

6.2.3 Programmable Button Connector (JP1).......................................................... 39

6.2.4 Speaker Connector (CN5)................................................................................ 39

6.2.5 Operation Mode Selection Jumper (CN1) ....................................................... 39

A REGULATORY COMPLIANCE.............................................................................. 40

B SAFETY PRECAUTIONS......................................................................................... 45

SAFETY PRECAUTIONS............................................................................................. 46

B.1

B.1.1 General Safety Precautions............................................................................. 46

B.1.2 Anti-static Precautions.................................................................................... 47

B.1.3 Product Disposal............................................................................................. 48

B.2 MAINTENANCE AND CLEANING PRECAUTIONS........................................................ 48

B.2.1 Maintenance and Cleaning.............................................................................. 48

B.2.2 Cleaning Tools................................................................................................. 49

C HAZARDOUS MATERIALS DISCLOSURE ......................................................... 50

C.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS

Page v

OHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ....................................... 51

R

VTT-1000 Vehicle Tracking Terminal

Page vi

VTT-1000 Vehicle Tracking Terminal

List of Figures

Figure 1-1: VTT-1000 Panel PC......................................................................................................2

Figure 1-2: Front View....................................................................................................................3

Figure 1-3: Side Panels..................................................................................................................4

Figure 1-4: Bottom Panel...............................................................................................................5

Figure 1-5: Rear View.....................................................................................................................5

Figure 1-6: Dimensions (unit: mm)...............................................................................................8

Figure 3-1: Rubber Cover of Left Panel......................................................................................14

Figure 3-2: SIM Card Installation.................................................................................................15

Figure 3-3: Rubber Cover of Left Panel......................................................................................15

Figure 3-4: microSD Card Installation........................................................................................16

Figure 3-5: Secure Suction Cup and Bracket ............................................................................17

Figure 3-6: Install the Mounting Kit ............................................................................................18

Figure 3-7: Secure the Mounting Kit to the Windshield............................................................18

Figure 3-8: DIO and Serial Communication Cable ....................................................................19

Figure 3-9: Digital I/O and RS-232 Connector Pinouts Location .............................................19

Figure 3-10: RS-232 Cable...........................................................................................................20

Figure 3-11: RS-232 Connector Pinout Locations.....................................................................20

Figure 3-12: D-Sub 9 Connector Pinouts of the RS-232 Cable................................................21

Figure 3-13: Power Input Connector...........................................................................................21

Figure 3-14: Cigarette Lighter Cable...........................................................................................21

Figure 3-15: USB Device Connection.........................................................................................22

Figure 3-16: Power Connector ....................................................................................................23

Figure 3-17: Powering Off............................................................................................................24

Figure 3-18: Updating OS ............................................................................................................25

Figure 4-1: VTT_UTILS Tool ........................................................................................................27

Figure 4-2: Register Utils.............................................................................................................27

Figure 6-1: Main Board Layout Diagram (Front Side)...............................................................35

Figure 6-2: Main Board Layout Diagram (Solder Side).............................................................35

Page vii

VTT-1000 Vehicle Tracking Terminal

List of Tables

Table 1-1: Technical Specifications..............................................................................................7

Table 2-1: Packing List.................................................................................................................11

Table 2-2: Optional Item...............................................................................................................11

Table 3-1: Digital I/O and RS-232 Connector Pinouts...............................................................19

Table 3-2: RS-232 Connector Pinouts ........................................................................................20

Table 6-1: Peripheral Interface Connectors...............................................................................36

Table 6-2: 3G Module Connector (CN6) Pinouts .......................................................................37

Table 6-3: LCD Connector (LCM1) Pinouts................................................................................38

Table 6-4: Programmable Button Connector (JP1) Pinouts.....................................................39

Table 6-5: Speaker Connector (CN5) Pinouts............................................................................39

Table 6-6: Operation Mode Selection Jumper (CN1) Settings .................................................39

Page viii

VTT-1000 Vehicle Tracking Terminal

Chapter

1

1 Introduction

Page 1

1.1 Overview

Figure 1-1: VTT-1000 Panel PC

The VTT-1000 is a 3.5” panel PC designed for in-car use.

VTT-1000 Vehicle Tracking Terminal

At the heart of the system is the Samsung ARM9 processor, offering low power in a

powerful package. The VTT-1000 provides GSM/GPRS communication and is a GPS

ready system. The system also offers a multimedia experience with a 1.5 W speaker.

Other peripherals include one USB mini-B port, digital I/O port, two RS-232 ports and an

audio output.

1.2 Features

There are two models in the VTT-1000. Both models feature the following:

 3.5” TFT LCD touch screen

 Embedded with ARM9 400MHz CPU

 Pre-installed Microsoft Windows CE 6.0

 Built-in GSM/GPRS and antenna

 uBlox MAX-6Q GPS Receiver

 On-board 128 MB DDR2 memory

 IP 54 compliant front panel

 RoHS compliance

Page 2

VTT-1000 Vehicle Tracking Terminal

1.3 Front Panel

The front of the VTT-1000 is a flat panel screen with a plastic frame. The components on

the front panel are list below:

 LED indicators:

o Red: power LED
o Green: GPRS LED
o Blue: GPS LED

 1 x Speaker (1.5 W)

 7 x Programmable buttons

Figure 1-2: Front View

Page 3

1.4 Side Panels

The left panel has a SIM card slot and a microSD card slot. These slots are both protected

by a rubber cover.

The right panel has an optional power switch, a reset button and one audio line-out jack.

The switch and the connector are both protected by a rubber cover.

VTT-1000 Vehicle Tracking Terminal

Figure 1-3: Side Panels

1.5 Bottom Panel

The following are found on the bottom panel.

 1 x 9 V–30 V DC input connector

 1 x USB 2.0 mini-B connector

 1 x RS-232 connector

 1 x Digital I/O and RS-232 connector

Page 4

VTT-1000 Vehicle Tracking Terminal

Figure 1-4: Bottom Panel

1.6 Rear Panel

The rear panel has mounting holes and an external GPS antenna connector.

Figure 1-5: Rear View

Page 5

1.7 System Specifications

The technical specifications for the VTT-1000 systems are listed in Table 1-1.

System
CPU Samsung S3C2416 ARM9 400 MHz
Memory On-board 128 MB 133 MHz DDR2 memory
OS Microsoft Windows Embedded CE 6.0
Storage 256 MB NAND flash memory

1 x microSD card slot

Audio 1 x Speaker (1.5 W)

1 x Audio line-out jack

Digital I/O 2 inputs/ 2 outputs
Display

VTT-1000 Vehicle Tracking Terminal

LCD 3.5” TFT LCD with 4-wire resistive touchscreen
Max. Resolution 320 x 240 (QVGA)
Brightness (cd/m2) 450
Viewing Angle 50/55/60/60 degree
Communication
WWAN Quad-Band GSM 800/850/900/1700/1900/2100 MHz

GPRS Class 12
GSM 850/900/1800/1900 MHz

GPS u-blox MAX-6Q GPS module supports expandable external antenna
Power
Power Input 9 V ~ 30 V DC input via cigarette lighter power cable
Physical Character
Construction Material ABS + PC plastic front frame
Mounting Suction mount
Dimensions (W x H x D) 128 mm x 89 mm x 32 mm
Operation Temperature -20ºC ~ 50ºC

Page 6

Storage Temperature -30ºC ~ 70ºC
Humidity 5% ~ 85% non-condense
Net weight 177 g
IP level (front panel) IP 54

VTT-1000 Vehicle Tracking Terminal

Drop Survival 1 M
Safety CE/FCC/E-MARK/BSMI
Connectors and Buttons
Antenna Connector 1 x External GPS antenna connector

I/O Ports and Switches 1 x 9 V~ 30 V DC input connector

1 x USB 2.0 mini-B connector
1 x Digital I/O and RS-232 connector
1 x RS-232 connector
1 x Audio line-out jack
1 x microSD slot
1 x SIM card slot
1 x Reset button
1 x Power switch (optional)

Front Panel Buttons 7 x Programmable buttons
Front Panel Indicators Red: power LED

Green: GPRS LED
Blue: GPS LED

Table 1-1: Technical Specifications

Page 7

1.8 Dimensions

The dimensions are shown below.

VTT-1000 Vehicle Tracking Terminal

Page 8

Figure 1-6: Dimensions (unit: mm)

VTT-1000 Vehicle Tracking Terminal

Chapter

2

2 Unpacking

Page 9

To unpack the panel PC, follow the steps below:

VTT-1000 Vehicle Tracking Terminal

WARNING!

The front side LCD screen has a protective plastic cover stuck to the

screen. Only remove the plastic cover after the system has been

properly installed. This ensures the screen is protected during the

installation process.

Step 1: Open the box and lift the VTT-1000 out of the box.

Step 2: Remove the plastic bag from the system.

Step 3: Make sure all the components listed in the packing list are present.

The VTT-1000 is shipped with the following components:

Quantity Item Image

1 VTT-1000 vehicle tracking terminal

1 Cigarette lighter power cable

(P/N: 32002-004600-100-RS)

1 GPS Antenna

(P/N: 32502-000700-100-RS)

Page 10

1 RS-232 cable

(P/N: 32024-002700-100-RS)

VTT-1000 Vehicle Tracking Terminal

Quantity Item Image

1 Serial commnunication cable

(P/N: 32016-000300-100-RS)

1 User manual CD and driver CD

Table 2-1: Packing List

The following is optional item that may be purchased separately.

Item Image

Vehicle mounting bracket with single suction cup

(P/N: VTT-1000-MT01-R10)

Table 2-2: Optional Item

If any of these items are missing or damaged, contact the distributor or sales

representative immediately.

Page 11

VTT-1000 Vehicle Tracking Terminal

Chapter

3

3 Installation

Page 12

VTT-1000 Vehicle Tracking Terminal

3.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the maintenance of the

VTT-1000 may result in permanent damage to the VTT-1000 and

severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the VTT-1000. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the VTT-1000 is accessed internally, or any other electrical

component is handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

 Self-grounding: - Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

 Use an anti-static pad: - When configuring the VTT-1000, place it on an

anti-static pad. This reduces the possibility of ESD damaging the VTT-1000.

3.2 Installation Precautions

When installing the flat panel PC, please follow the precautions listed below:

 Power turned off: When installing the flat panel PC, make sure the power is

off. Failing to turn off the power may cause severe injury to the body and/or

damage to the system.

 Certified Engineers: Only certified engineers should install and modify

onboard functionalities.

 Anti-static Discharge : If a user open the rear panel of the flat panel PC, to

configure the jumpers or plug in added peripheral devices, ground themselves

first and wear an anti-static wristband.

Page 13

VTT-1000 Vehicle Tracking Terminal

3.3 Installation and Configuration Steps

The following installation steps must be followed.

Step 1: Unpack the system

Step 2: Install a 3G SIM card

Step 3: Install a microSD card

Step 4: Connect peripheral devices

Step 5: Mount the system

Step 6: Power up the system Step 0:

3.4 SIM Card Installation

To install the SIM card, follow the instructions below.

Step 1: Open the rubber cover from the left panel of the VTT-1000.

Page 14

Figure 3-1: Rubber Cover of Left Panel

VTT-1000 Vehicle Tracking Terminal

Step 2: Locate the SIM card slot. Insert a SIM card into the slot.

Figure 3-2: SIM Card Installation

Step 3: Close the rubber cover. Step 0:

3.5 microSD Card Installation

To install the microSD card, follow the instructions below.

Step 1: Open the rubber cover from the left panel of the VTT-1000.

Figure 3-3: Rubber Cover of Left Panel

Page 15

Step 2: Locate the microSD card slot. Insert a microSD card into the slot.

Figure 3-4: microSD Card Installation

VTT-1000 Vehicle Tracking Terminal

Step 3: Close the rubber cover. Step 0:

3.6 Mounting the System (Optional)

The VTT-1000 mounting kit can be purchased separately. To mount the system using the

optional mounting kit, please follow the steps below.

Step 1: Attach and secure the suction cup to the mounting bracket as shown in Figure

3-5.

Page 16

VTT-1000 Vehicle Tracking Terminal

Figure 3-5: Secure Suction Cup and Bracket

Step 2: Install the mounting kit to the VTT-1000 from its rear panel (Figure 3-6).

Step 3: Select a suit

dry it.

Step 4: Attach the suction cup to the windshield (Figure 3-6). Make

suction cup is against the windshield.

able place on the windshield to mount the VTT-1000, then clean and

sure the lever on the

Page 17

VTT-1000 Vehicle Tracking Terminal

Figure 3-6: Install the Mounting Kit

Step 5: Press the suction cup and flip the lever toward the windshield to secure the

mounting kit (Figure 3-7).

Figure 3-7: Secure the Mounting Kit to the Windshield

Page 18

VTT-1000 Vehicle Tracking Terminal

3.7 Bottom Panel Connectors

This section provides and overview of the connectors on the bottom panel.

3.7.1 Digital I/O and RS-232 Connection

The VTT-1000 right side panel has one 14-pin wafer connector for digital I/O and RS-232
connection. Use the DIO and serial communication cable (Figure 3-8) i

n the package to

connect the VTT-1000 with the vehicle.

Figure 3-8: DIO and Serial Communication Cable

The pinouts for digital I/O and RS-232 connector are listed in the table below.

Figure 3-9: Digital I/O and RS-232 Connector Pinouts Location

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 EXT1_RTS 2 EXT1_TX
3 EXT1_DTR 4 EXT1_RX
5 EXT1_CTS 6 EXT1_DSR
7 EXT1_RI 8 EXT1_DCD
9 B_D0 10 F_CPU_DO0
11 B_D1 12 F_CPU_DO1
13 NC 14 GND

Table 3-1: Digital I/O and RS-232 Connector Pinouts

Page 19

3.7.2 RS-232 Connection

The VTT-1000 has one 8-pin wafer connector for RS-232 connection. Use the RS-232

VTT-1000 Vehicle Tracking Terminal

cable (Figure 3-10) in the packa

ge to connect the VTT-1000 with the vehicle.

Figure 3-10: RS-232 Cable

The pinouts for RS-232 connector of the VTT-1000 are listed in the table below.

Figure 3-11: RS-232 Connector Pinout Locations

Pin Description

1 N/A
2 COM4_RXD
3 N/A
4 COM4_TXD
5 N/A
6 N/A
7 N/A
8 GND

Table 3-2: RS-232 Connector Pinouts

The DB-9 pinouts of the RS-232 cable is shown below.

Page 20

VTT-1000 Vehicle Tracking Terminal

Figure 3-12: D-Sub 9 Connector Pinouts of the RS-232 Cable

3.7.3 Power Input Connection

The VTT-1000 has one 9 V–30 V DC input connector on the bottom panel.

Figure 3-13: Power Input Connector

The VTT-1000 can use DC power from the vehicle. To use DC power, connect the

VTT-1000 to the vehicle cigarette lighter connector through the cigarette lighter cable. See

Figure 3-14.

Figure 3-14: Cigarette Lighter Cable

3.7.4 USB Device Connection

There is one external USB 2.0 mini-B connector. To connect a USB device, please follow

the instructions below.

Page 21

Step 1: Located the USB connector. The location of the USB connector is shown in

Chapter 1.

Step 2: Align the connectors. Align the USB device connector with the connector on

the bottom panel.

VTT-1000 Vehicle Tracking Terminal

Figure 3-15: USB Device Connection

Step 3: Insert the device connector. Once aligned, gently insert the USB device

connector into the onboard connector. Step 0:

3.8 Power-On Procedure

3.8.1 Installation Checklist

WARNING:

Make sure a power supply with the correct input voltage is being fed into

the system. Incorrect voltages applied to the system may cause damage to

the internal electronic components and may also cause injury to the user.

Page 22

To power on the embedded system please make sure of the following:

VTT-1000 Vehicle Tracking Terminal

 The SIM card is installed

 The bottom cover is installed

 All peripheral devices (antenna, serial communications devices etc.) are

connected

 The system is securely mounted

 The power cables are plugged in

3.8.2 Power-on Procedure

To power-on the VTT-1000 please follow the steps below:

Step 1: Connect the cigarette lighter power cable from the VTT-1000 to the vehicle.

Figure 3-16: Power Connector

Step 2: Once the power is connected, the VTT-1000 will automatically turn on. The

power LED on the front panel will turn to red.

Step 3: To turn off the VTT-1000, adjust the power switch to the power off position as

shown in Figure 3-17. Step 0:

Page 23

VTT-1000 Vehicle Tracking Terminal

Figure 3-17: Powering Off

NOTE:

The VTT-1000-T35A/128MB-R20-TIC model can not be powered off by

adjusting the power switch.

3.9 System Maintenance

3.9.1 Software

To update the OS, please follow the steps below.

Step 1: Format a microSD card to FAT32 format

Step 2: Save the following files to the microSD card from the utility CD:

 EBOOT.bin

 logo.bmp (24-bit bitmap with 320x240 resolution, RGB true color)

 NK.bin

Page 24

 STEPLDR.nb0

 update.enable

Step 3: Insert the microSD card into the VTT-1000.

VTT-1000 Vehicle Tracking Terminal

Step 4: Turn on the VTT-1000.

Step 5: The VTT-1000 starts updating OS and the logo image. The red bar on the

screen shows the update progress. (A blue bar shows if the system boot-up in

normal mode).

Figure 3-18: Updating OS

Step 6: A touchscreen calibration is required after the first OS update. After finishing the

touchscreen calibration, remove the microSD card and reboot the VTT-1000.

3.9.2 Hardware

If the components of the VTT-1000 fail, they must be replaced. Please contact the system

reseller or vendor to purchase the replacement parts.

NOTE:

A user cannot replace a motherboard. If the motherboard fails it must

be shipped back to IEI to be replaced. Please contact the system

vendor, reseller or an IEI sales person directly.

Page 25

VTT-1000 Vehicle Tracking Terminal

Chapter

4

4 Application Tools

Page 26

VTT-1000 Vehicle Tracking Terminal

4.1 Introduction

The following sections introduce two utility tools in the VTT-1000.

4.1.1 VTT_UTILS

The VTT_UTILS tool (VTT_UTILS.exe) enables users to setup applications that will be

launched at the start-up. The user interface of the VTT_UTILS is shown below.

Figure 4-1: VTT_UTILS Tool

4.1.2 Register Utils

The Register Utils (RegUtils.exe) tool enables users to restore or backup the register

settings. The user interface of the RegUtils is shown below.

Figure 4-2: Register Utils

Page 27

VTT-1000 Vehicle Tracking Terminal

Chapter

5

5 SDK

Page 28

VTT-1000 Vehicle Tracking Terminal

5.1 Introduction

The IEI VTT-1000 SDK provides API for programmers to write applications for the system.

Although APIs are designed for programmers, they are ultimately good for users because

they guarantee that all programs using a common API will have similar interfaces. This

makes it easier for users to learn new programs.

Before using the SDK, please remember to install the mini USB driver to the computer.

The mini USB driver is available in the accompanying utility CD.

5.2 Demo Application

IEI provides an application for VTT-1000 demonstration. To run the demo application,

please execute the following EXE file.

 Testing.exe:

o Function: configure DIO, COM port, programming key, temperature,

o Setting file: testing.ini

5.3 VTT -1000 API

The following sections introduce the details of the VTT-1000 APIs.

 VTT1000Dll.dll

o Digital IO API
o G-Sensor API
o Programming Key API
o Temperature API
o E-Compass API

G-Sensor and GPRS

Define 1 is true execute, 0 is false no execute:
autorun=1 (Auto execute test)
log=1 (test and recording)
burn=1 (Loop Test)

o COM API

 CEIcpFleetMangDll.dll

o GPS API

Page 29

5.3.1 Digital I/O API

BOOL DIO_WRITE0(byte* pByteHighOrLow):

 Input : byte*, 1 byte data

 Output : void

 Return : BOOL, true or false

BOOL DIO_WRITE1(byte* pByteHighOrLow):

 Input : byte*, 1 byte data

 Output : void

 Return : BOOL, true or false

BOOL DIO_READ0(byte* pByteHighOrLow):

VTT-1000 Vehicle Tracking Terminal

 Pin 1 read

 Input : void

 Output : byte*, 8 byte array buffer

 Return : BOOL, true or false

BOOL DIO_WRITE1(byte* pByteHighOrLow):

 Pin 2

 Input : void

 Output : byte*, 8 byte array buffer

 Return : BOOL, true or false

5.3.2 COM (Serial) Port API

BOOL COM_Open( int nPort, int nBaud ):

 Input : int, port number

 Input : int, boud rate

Page 30

 Output : void

 Return : BOOL, true or false

VTT-1000 Vehicle Tracking Terminal

　 BOOL COM_Close():

 Input : void

 Input : void

 Output : void

 Return : BOOL, true or false

　 BOOL COM_IsOpened():

 Input : void

 Output : void

 Return : BOOL, true or false

　 int COM_ReadData(byte* pBufData, int iSize ):

 input : int, read length

 output : byte*, byte array data

 return : int, read length

5.3.3 T emperature API

BOOL GetCurrTemperatureValue(DOUBLE* pDblTempValue):

 Input : void

 Output : DOUBLE*, temperature value

 Return : BOOL, true or false

5.3.4 Programming Key API

BOOL GetKeyPadValue(BYTE* pByteKeyNum):

 Return : true if succeed, false if fail

 Output : BYTE* pByteKeyNum

 Input : void

*pByteKeyNum=1:press Key1, *pByteKeyNum=2:press Key2

*pByteKeyNum=3:press Key3, *pByteKeyNum=4:press Key4

*pByteKeyNum=5:press Key5, *pByteKeyNum=6:press Key6

*pByteKeyNum=7:press Key7, *pByteKeyNum=0:failed

Page 31

5.3.5 E-Compass API

BOOL GetCompassModeValue(INT32* pIntModeValue):

 Return : true if succeed, false if fail

 Output : INT32* pIntModeValue

 Input : void

*pIntModeValue=0:continuous mode, *pIntModeValue=1:single mode

*pIntModeValue=2:idle mode, *pIntModeValue=3:sleep mode

*pIntModeValue=-1:failed

BOOL SetCompassModeValue(INT32* pIntModeValue):

 Return : true if succeed, false if fail

 Input : INT32* pIntModeValue

*pIntModeValue=0:continuous mode, *pIntModeValue=1:single mode

VTT-1000 Vehicle Tracking Terminal

*pIntModeValue=2:idle mode, *pIntModeValue=3:sleep mode

*pIntModeValue=-1:failed

BOOL GetCompassStatusValue(INT32* pIntStatusValue):

 Return : true if succeed, false if fail

 Output : INT32* pIntStatusValue

*pIntStatusValue=1 : X,Y,Z data are ready to read.

*pIntStatusValue=2 : Not all for of the x,y,z data have been read

*pIntStatusValue=-1:failed

BOOL GetCompassData(UINT32* pIntX, UINT32* pIntY, UINT32* pIntZ):

 Return : true if succeed, false if fail

 Output : UINT32* pIntX, UINT32* pIntY, UINT32* pIntZ

X,Y,Z axis integer data, range from 63488 to 2047(0xF800 to 0x07FF)

5.3.6 G-Sensor API

Page 32

BOOL GetGSensorData(UINT32* pIntX, UINT32* pIntY, UINT32* pIntZ):

 Return : true if succeed, false if fail

VTT-1000 Vehicle Tracking Terminal

 Output : UINT32* pIntX, UINT32* pIntY, UINT32* pIntZ

X,Y,Z axis integer data

Page 33

VTT-1000 Vehicle Tracking Terminal

Chapter

6

6 Interface Connectors

Page 34

VTT-1000 Vehicle Tracking Terminal

6.1 Peripheral Interface Connectors

The motherboard of the VTT-1000 comes with a number of peripheral interface
connectors and configuration jumpers. The connector locations are shown in Figure 6-1
and Figure 6-2. The Pin 1 locations of the on-board connectors are also indicated in the

diagrams below. The connector pinouts for these connectors are listed in the following

sections.

Figure 6-1: Main Board Layout Diagram (Front Side)

Figure 6-2: Main Board Layout Diagram (Solder Side)

Page 35

VTT-1000 Vehicle Tracking Terminal

6.2 Internal Peripheral Connectors

Internal peripheral connectors are found on the motherboard and are only accessible

when the motherboard is outside of the chassis. The table below shows a list of the

peripheral interface connectors on the VTT-1000 motherboard. Pinouts of these

connectors can be found in the following sections.

Connector Type Label

3G antenna connector

(located on the 3G module)

3G module connector 50-pin connector CN6

Debug connector 3-pin wafer CN4

Function buttons (F1–F4)

GPS antenna connector 3-pin coaxial ANT1

LCD connector 54-pin FPC LCM1

Programmable button

connector (F5–F7)

Speaker connector 2-pinwafer CN5

Operation mode selection 6-pin header CN1

3-pin coaxial ANT2

Tact switch K_SW1,

K_SW2,

K_SW3,

K_SW4

8-pin wafer JP1

Table 6-1: Peripheral Interface Connectors

6.2.1 3G Module Connector (CN6)

WARNING:

A 3G module is connected to this connector when shipped. This

connector is designed only for the preinstalled 3G module. Installing

other device into this connector may result in damage to the system.

Page 36

VTT-1000 Vehicle Tracking Terminal

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 3G_3P8V 26 SIM_CLK
2 3G_3P8V 27 SIM_VCC
3 3G_3P8V 28 SIM_CIO
4 3G_3P8V 29 SIM_RST
5 3G_3P8V 30 SIM_VCC
6 GND 31 N/A
7 N/A 32 N/A
8 N/A 33 N/A
9 N/A 34 N/A
10 N/A 35 N/A
11 N/A 36 N/A
12 N/A 37 N/A
13 N/A 38 SYNC
14 N/A 39 N/A
15 M_EMER_OFF 40 N/A
16 GPIO-IGT 41 N/A
17 3G_1V8 42 N/A
18 N/A 43 DN1
19 N/A 44 DP1
20 N/A 45 VUSB1
21 N/A 46 GND
22 N/A 47 GND
23 N/A 48 GND
24 N/A 49 GND
25 N/A 50 GND

Table 6-2: 3G Module Connector (CN6) Pinouts

Page 37

6.2.2 LCD Connector (LCM1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 VLED- 28 VD1_16
2 VLED- 29 VD1_17
3 VLED+ 30 VD1_18
4 VLED+ 31 VD1_19
5 N/A 32 VD1_20
6 CPU_nRST 33 VD1_21
7 N/A 34 VD1_22
8 TSXP 35 VD1_23
9 TSYM 36 RGB_HSYNC_1
10 TSXM 37 RGB_VSYNC_1
11 TSYP 38 LCD_DCLK

VTT-1000 Vehicle Tracking Terminal

12 VD1_0 39 N/A
13 VD1_1 40 N/A
14 VD1_2 41 VCC_3P3V
15 VD1_3 42 VCC_3P3V
16 VD1_4 43 LCD_LEND
17 VD1_5 44 N/A
18 VD1_6 45 N/A
19 VD1_7 46 N/A
20 VD1_8 47 N/A
21 VD1_9 48 N/A
22 VD1_10 49 SPCLK
23 VD1_11 50 SPDAT
24 VD1_12 51 N/A
25 VD1_13 52 LCD_VDEN
26 VD1_14 53 GND
27 VD1_15 54 GND

Page 38

Table 6-3: LCD Connector (LCM1) Pinouts

VTT-1000 Vehicle Tracking Terminal

6.2.3 Programmable Button Connector (JP1)

PIN NO. DESCRIPTION

1 GND
2 N/A
3 KEY 7
4 KEY 6
5 KEY 5
6 MIC2P
7 MICBIAS2
8 VCC_3P3V

Table 6-4: Programmable Button Connector (JP1) Pinouts

6.2.4 Speaker Connector (CN5)

PIN NO. DESCRIPTION

1 SPK_P
2 SPK_N

Table 6-5: Speaker Connector (CN5) Pinouts

6.2.5 Operation Mode Selection Jumper (CN1)

Setting DESCRIPTION

Short 1-2

Short 3-4, 5-6 Boot the system via NAND (Default)

Boot the system via microSD card (please use
this setting for updating firmware).

Table 6-6: Operation Mode Selection Jumper (CN1) Settings

Page 39

VTT-1000 Vehicle Tracking Terminal

Appendix

A

A Regulatory Compliance

Page 40

VTT-1000 Vehicle Tracking Terminal

DECLARATION OF CONFORMITY

This equipment is in conformity with the following EU directives:

 EMC Directive 2004/108/EC

 Low-Voltage Directive 2006/95/EC

 RoHS II Directive 2011/65/EU

 Ecodesign Directive 2009/125/EC

If the user modifies and/or install other devices in the equipment, the CE conformity

declaration may no longer apply.

If this equipment has telecommunications functionality, it also complies with the

requirements of the R&TTE Directive 1999/5/EC.

English

IEI Integration Corp declares that this equipment is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

Български [Bulgarian]

IEI Integration Corp. декларира, че този оборудване е в съответствие със

съществените изисквания и другите приложими правила на Директива

1999/5/ЕС.

Česky [Czech]

IEI Integration Corp tímto prohlašuje, že tento zařízení je ve shodě se základními

požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk [Danish]

IEI Integration Corp erklærer herved, at følgende udstyr overholder de væsentlige

krav og øvrige relevante krav i direktiv 1999/5/EF.

Deutsch [German]

IEI Integration Corp, erklärt dieses Gerät entspricht den grundlegenden

Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.

Eesti [Estonian]

IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 1999/5/EÜ

põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Page 41

Español [Spanish]

IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y

cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Ελληνική [Greek]

IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ

ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ

1999/5/ΕΚ.

Français [French]

IEI Integration Corp déclare que l'appareil est conforme aux exigences essentielles et

aux autres dispositions pertinentes de la directive 1999/5/CE.

Italiano [Italian]

IEI Integration Corp dichiara che questo apparecchio è conforme ai requisiti essenziali

ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Latviski [Latvian]

VTT-1000 Vehicle Tracking Terminal

IEI Integration Corp deklarē, ka iekārta atbilst būtiskajām prasībām un citiem ar to

saistītajiem noteikumiem Direktīvas 1999/5/EK.

Lietuvių [Lithuanian]

IEI Integration Corp deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas

1999/5/EB Direktyvos nuostatas.

Nederlands [Dutch]

IEI Integration Corp dat het toestel toestel in overeenstemming is met de essentiële

eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Malti [Maltese]

IEI Integration Corp jiddikjara li dan prodott jikkonforma mal-ħtiġijiet essenzjali u ma

provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Magyar [Hungarian]

IEI Integration Corp nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ

követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski [Polish]

IEI Integration Corp oświadcza, że wyrobu jest zgodny z zasadniczymi wymogami

Page 42

oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

Português [Portuguese]

IEI Integration Corp declara que este equipamento está conforme com os requisitos

essenciais e outras disposições da Directiva 1999/5/CE.

VTT-1000 Vehicle Tracking Terminal

Româna [Romanian]

IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele

esenţiale şi cu celelalte prevederi relevante ale Directivei 1999/5/CE.

Slovensko [Slovenian]

IEI Integration Corp izjavlja, da je ta opreme v skladu z bistvenimi zahtevami in

ostalimi relevantnimi določili direktive 1999/5/ES.

Slovensky [Slovak]

IEI Integration Corp týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a

všetky príslušné ustanovenia Smernice 1999/5/ES.

Suomi [Finnish]

IEI Integration Corp vakuuttaa täten että laitteet on direktiivin 1999/5/EY oleellisten

vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Svenska [Swedish]

IEI Integration Corp förklarar att denna utrustningstyp står I överensstämmelse med

de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av

direktiv 1999/5/EG.

Page 43

FCC WARNING

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

 This device may not cause harmful interference, and

 This device must accept any interference received, including interference that

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in

VTT-1000 Vehicle Tracking Terminal

may cause undesired operation.

a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Page 44

VTT-1000 Vehicle Tracking Terminal

B Safety Precautions

Appendix

B

Page 45

VTT-1000 Vehicle Tracking Terminal

WARNING:

The precautions outlined in this chapter should be strictly followed.

Failure to follow these precautions may result in permanent damage to

the VTT-1000.

WARNING:

This is Class A Product. In domestic environment this product may

cause radio interference in which case the user may be required to

take adequate measures.

B.1 Safety Precautions

Please follow the safety precautions outlined in the sections that follow:

B.1.1 General Safety Precautions

Please ensure the following safety precautions are adhered to at all times.

 Follow the electrostatic precautions outlined below whenever the

VTT-1000 is opened.

 Make sure the power is turned off and the power cord is disco nnected

whenever the VTT-1000 is being installed, moved or modified.

 Do not apply voltage levels that exceed the specified voltage range.

Doing so may cause fire and/or an electrical shock.

 Electric shocks can occur if the VTT-1000 chassis is opened when the

VTT-1000 is running.

 Do not drop or insert any objects into the ventilation openings of the

VTT-1000.

Page 46

 If considerable amounts of dust, water, or fluids enter the VTT-1000, turn

off the power supply immediately, unplug the power cord, and contact the

VTT-1000 vendor.

VTT-1000 Vehicle Tracking Terminal

 DO NOT:

o Drop the VTT-1000 against a hard surface.
o Strike or exert excessive force onto the LCD panel.
o Touch any of the LCD panels with a sharp object
o In a site where the ambient temperature exceeds the rated temperature

B.1.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the VTT-1000

may result in permanent damage to the VTT-1000 and severe injury to

the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the VTT-1000. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the VTT-1000 is opened and any of the electrical components are

handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-static wristband can

help to prevent ESD from damaging any electrical component.

 Self-grounding: Before handling any electrical component, touch any

grounded conducting material. During the time the electrical component is

handled, frequently touch any conducting materials that are connected to the

ground.

 Use an anti-static pad: When configuring or working with an electrical

component, place it on an antic-static pad. This reduces the possibility of ESD

damage.

 Only handle the edges of the electrical component: When handling the

electrical component, hold the electrical component by its edges.

Page 47

VTT-1000 Vehicle Tracking Terminal

B.1.3 Product Disposal

CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Only

certified engineers should replace the on-board battery.

Dispose of used batteries according to instructions and local

regulations.

 Outside the European Union - If you wish to dispose of used electrical and

electronic products outside the European Union, please contact your local

authority so as to comply with the correct disposal method.

 Within the European Union:

EU-wide legislation, as implemented in each Member State, requires that

waste electrical and electronic products carrying the mark (left) must be

disposed of separately from normal household waste. This includes

monitors and electrical accessories, such as signal cables or power cords.

When you need to dispose of your display products, please follow the

guidance of your local authority, or ask the shop where you purchased the product. The

mark on electrical and electronic products only applies to the current European Union

Member States.

Please follow the national guidelines for electrical and electronic product disposal.

B.2 Maintenance and Cleaning Precautions

When maintaining or cleaning the VTT-1000, please follow the guidelines below.

B.2.1 Maintenance and Cleaning

Page 48

Prior to cleaning any part or component of the VTT-1000, please read the details below.

VTT-1000 Vehicle Tracking Terminal

 Except for the LCD panel, never spray or squirt liquids directly onto any other

components. To clean the LCD panel, gently wipe it with a piece of soft dry

cloth or a slightly moistened cloth.

 The interior of the VTT-1000 does not require cleaning. Keep fluids away from

the VTT-1000 interior.

 Be cautious of all small removable components when vacuuming the

VTT-1000.

 Turn the VTT-1000 off before cleaning the VTT-1000.

 Never drop any objects or liquids through the openings of the VTT-1000.

 Be cautious of any possible allergic reactions to solvents or chemicals used

when cleaning the VTT-1000.

 Avoid eating, drinking and smoking within vicinity of the VTT-1000.

B.2.2 Cleaning Tools

Some components in the VTT-1000 may only be cleaned using a product specifically

designed for the purpose. In such case, the product will be explicitly mentioned in the
cleaning tips. Below is a list of items to use when cleaning the VTT-1000.

 Cloth – Although paper towels or tissues can be used, a soft, clean piece of

cloth is recommended when cleaning the VTT-1000.

 Water or rubbing alcohol – A cloth moistened with water or rubbing alcohol

can be used to clean the VTT-1000.

 Using solvents – The use of solvents is not recommended when cleaning the

VTT-1000 as they may damage the plastic parts.

 Vacuum cleaner – Using a vacuum specifically designed for computers is

one of the best methods of cleaning the VTT-1000. Dust and dirt can restrict

the airflow in the VTT-1000 and cause its circuitry to corrode.

 Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are

excellent tools for wiping hard to reach areas.

 Foam swabs - Whenever possible, it is best to use lint free swabs such as

foam swabs for cleaning.

Page 49

VTT-1000 Vehicle Tracking Terminal

Appendix

C

C Hazardous Materials

Disclosure

Page 50

VTT-1000 Vehicle Tracking Terminal

C.1 Hazardous Materials Disclosure Table for IPB Products

Certified as RoHS Compliant Under 2002/95/EC Without
Mercury

The details provided in this appendix are to ensure that the product is compliant with the

Peoples Republic of China (China) RoHS standards. The table below acknowledges the

presences of small quantities of certain materials in the product, and is applicable to China

RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly

Use Period” (EFUP). This is an estimate of the number of years that these substances

would “not leak out or undergo abrupt change.” This product may contain replaceable

sub-assemblies/components which have a shorter EFUP such as batteries and lamps.

These components will be separately marked.

Please refer to the table on the next page.

Page 51

Toxic or Hazardous Substances and Elements Part Name

VTT-1000 Vehicle Tracking Terminal

Housing
Display
Printed Circuit

Board
Metal

Fasteners
Cable

Assembly
Fan Assembly
Power Supply

Assemblies

Lead
(Pb)

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

Mercury
(Hg)

Cadmium
(Cd)

Hexavalent
Chromium
(CR(VI))

Polybrominated
Biphenyls
(PBB)

Polybrominated
Diphenyl
Ethers
(PBDE)

Battery

O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is

below the limit requirement in SJ/T11363-2006

X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for

this part is above the limit requirement in SJ/T11363-2006

O O O O O O

Page 52

VTT-1000 Vehicle Tracking Terminal

此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符

合中国 RoHS 标准规定的限量要求。

本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的

年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元

件将会单独标示出来。

部件名称

壳体
显示
印刷电路板
金属螺帽
电缆组装
风扇组装
电力供应组装
电池

O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。

有毒有害物质或元素
铅

(Pb)

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

O O O O O O

汞
(Hg)

镉
(Cd)

六价铬
(CR(VI))

多溴联苯
(PBB)

多溴二苯
醚

(PBDE)

Page 53