TUS3400
Page 1
IEI Technology Corp.
User Manual
Panel PC
MODEL:
TUS3400
Rev. 1.01 – 15 March, 2017
TUS3400
Page 2
Revision
Date Version Changes
17 September, 2013 1.00 Initial release
11 November, 2016 1.01 USB port update
TUS3400
Page 3
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order
to improve reliability, design and function and does not represent a commitment on
the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks
of their respective owners.
TUS3400
Page 4
Table of Contents
1. INTRODUCTION
………………………………………………………………...5
1.1 OVERVIEW……………………………………………………………………….6
1.2 DIMENSIONS…………………………………….……………………………….7
1.3 SPECIFICATIONS………………………………….…………………………….9
2 UNPACKING
………………………………………………………………………11
2.1 UNPACKING…………………………………………………………………….12
2.2 PACKING LIST………………………………………………………………….13
3 INSTALLATION
…………………………………………………………………14
3.1 ANTI-STATIC PRECAUTIONS…………….………………………………….15
3.2 INSTALLATION PRECAUTIONS…………………………………………….15
3.3 PREINSTALLED COMPONENTS…………………………………………….16
3.4 REMOVING THE BACK COVER……………………………………………..17
3.5 REMOVING THE CONSOLE………………………………………………….18
4 SYSTEM MAINTENANCE
……………………………………………………19
4.1 SYSTEM MAINTENANCE INTRODUCTION….……………………………20
4.2 MOTHERBOARD REPLACEMENT………………………………………….20
4.3 BACK COVER REMOVAL…………………………………………………….20
4.4 CONSOLE REPLACEMENT…………………………………………………..21
4.5 SO-DIMM REPLACEMENT…………………………………………………...21
5 SAFETY PRECAUTIONS
……………………………………………………...23
A.1 SAFETY PRECAUTIONS……………………………………….......…………24
A.1.1 General Safety Precautions………………………………………..………...24
A.1.2 Anti-static Precautions……………………………………………..………...25
A.1.3 Product Disposal ……………………………………………………………26
A.2 MAINTENANCE AND CLEANING PRECAUTIONS………………………26
A.2.1 Maintenance and Cleaning..…………………………………………………26
A.2.2 Cleaning Tools…………………………………………………………..…….27
A.2.3 Federal Communication Commission Interference Statement……………28
6 HAZARDOUS MATERIALS DISCLOSURE
…………………...........…...29
B.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS
CERTIFIED AS ROHS COMPLIANT UNDER 2002/95/EC WITHOUT
MERCURY…………………………………………………………………………...30
TUS3400
Page 5
1 Introduction
Chapter
1
TUS3400
Page 6
1.1 Overview
Figure 1-1: TUS3400 Portable Computer
The TUS3400 portable computer provides all the features of a PC. The TUS3400
provides wireless networking for integration into company/facility networks. The
major external device connections include USB 3.0/2.0 and serial port connectors.
Storage options include a 2.5” hard drive, allowing for flexibility in choosing solid
state drives or traditional hard drives. 2 HDMI outputs on the left side allow the
TUS3400 to connect to a second/third screen for duplicating the screen contents or
extending the user interface.
TUS3400
Page 7
1.2 Dimensions
TUS3400
Page 8
TUS3400 Dimensions (mm)
TUS3400
Page 9
1.3 Specifications
The technical specifications for the TUS3400 system are listed in below table.
Model Name TUS3400
MB
SBC Model TRN-HM65-MB
CPU 2nd Generation Intel® Core™i7-3555LE processor
Chipset Intel HM65
RAM 2 x 4G DDR3 1333 SO-DIMM (Support ECC)
Display
LCD Size 15"
Max Resolution 1024x768
Brightness (cd/m2) minimum of 300 nits
Contrast Ratio 500:1
LCD Color 16.2M
Pixel Pitch (mm) 0.297(H) x 0.297(V)
Viewing Angle (H-V) 170(H)/ 170(V)
I/O Port
1x Power DC-JACK Connector
1x RJ-45 Connector For LAN
2x USB3.0 port, 2x USB2.0 port
2 x HDMI connector
1xExt Power Switch connector
1xLine in Jack connector
1x Line out Jack connector
LED
Sleep LED Blue
Charging LED
Bi-color, blue or amber. It is amber when
charging, and blue when fully charged and the power adapter is
connected.
Storage 1 x 2.5" 1T HDD
Main Module
DVD
1 x Slot-in DVD, 8x SuperDrive DVD +/‐ R DL/DVD +/‐RW, CD‐ RW
WiFi 1 x Wireless LAN 802.11a/b/g/n module by internal Mini PCIe interface
Speaker
2 x stereo speakers + 1 x sub‐woofer (internal speaker)
Console 1 x Keyboard/Trackball Console
Camera module
Up to UXGA resolution (1600X1200) to take still image, support VGA
(640x480) resolution up to 30fps at YUY2 mode
TUS3400
Page 10
Physical
Construction
Material
PC+ABS
Dimension (WxHxD) 388.3*395.6*88.45 (mm)
Weight 6.8kg
Magnetic Latch
a. Magnet size：30mm x 8mm x 6mm.
b. Q'ty : 8pcs (B part*4, C part *4)
c. Open/Close Force : 2.0kgf ~ 2.5kgf.
Environment
Operation
Temperature
0~35°C
Storage
Temperature
0~60°C
Power
Battery SANYO UR18650FK, 11.1V, 5400mah, 3S2P=59.94WH
Power Supply Power adapter: medical grade AC/DC adapter, Output: 19 VDC
OS Windows 7 32bit
Others
Logo Terason, illuminated logo
Flip-down feet
TUS3400
Page 11
2 Unpacking
Chapter
2
TUS3400
Page 12
2.1 Unpacking
To unpack the Portable Computer, follow the steps below:
WARNING!
The front side LCD screen has a protective plastic cover stuck to the
screen. Only remove the plastic cover after the panel PC has been
properly installed. This ensures the screen is protected during the
installation process.
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side
of the external (second) box.
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side
of the internal (first) box.
Step 4: Lift the monitor out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Pull the plastic cover off the portable computer.
Step 7: Make sure all the components listed in the packing list are present. Step 0:
TUS3400
Page 13
2.2 Packing List
The TUS3400 is shipped with the following components:
Quantity Item Remark
1 TUS3400
1 Power Adapter
(P/N: TRN-63040-010120-020-RS)
Packing List
If any of the above items are missing or damaged, contact the distributor or sales
representative immediately.
TUS3400
Page 14
3
Installation
Chapter
3
TUS3400
Page 15
3.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the maintenance may
result in permanent damage to the system and severe injury to the
user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the TUS3400. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever the TUS3400 is accessed internally, or any other
electrical component is handled, the following anti-static precautions are strictly
adhered to.
Wear an anti-static wristband: - Wearing a simple anti-static wristband
can help to prevent ESD from damaging the board.
Self-grounding: - Before handling the board touch any grounded
conducting material. During the time the board is handled, frequently
touch any conducting materials that are connected to the ground.
Use an anti-static pad: - When configuring the TUS3400, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
TUS3400.
Only handle the edges of the PCB: - When handling the PCB, hold the
PCB by the edges.
3.2 Installation Precautions
When installing the portable computer, please follow the precautions listed below:
Power turned off: When installing the portable computer, make sure the
power is off. Failing to turn off the power may cause severe injury to the
body and/or damage to the system.
Certified Engineers: Only certified engineers should install and modify
onboard functionalities.
TUS3400
Page 16
Anti-static Discharge: If a user open the portable computer to configure
the jumpers or plug in added peripheral devices, ground themselves
first and wear and anti-static wristband.
3.3 Preinstalled Components
The following components are all preinstalled.
Motherboard
DDR3 memory module
TFT LCD
System cooling fans
CPU
HDD
Wi-Fi module
Optical disk drive
TUS3400
Page 17
3.4 Removing the Back Cover
Remove all the retention screws on the back cover. Lift the cover up to remove.
TUS3400
Page 18
3.5 Removing the Console
Remove all the retention screws on the chassis base. Lift the console up to remove.
TUS3400
Page 19
Chapter
4
4 System Maintenance
TUS3400
Page 20
4.1 System Maintenance Introduction
The following system components may require maintenance.
Motherboard
SO-DIMM module
Wifi module
Cooling fans
HDD
If these components fail, they must be replaced. Please contact the system reseller
or vendor to purchase replacement parts. Replacement instructions for the above
listed components are described below.
4.2 Motherboard Replacement
A user cannot replace a motherboard. If the motherboard fails it must be shipped
back to IEI to be replaced. If the system motherboard has failed, please contact the
system vendor, reseller or an IEI sales person directly.
4.3 Back Cover Removal
WARNING!
Before removing the back cover, make sure all power to the
system has been disconnected. Failing to do so may cause severe
damage to the TUS3400 and injury to the user.
To access the HDD and install ECG, ultrasound module, the back cover must be
removed. To remove the back cover, please refer to Section
599H
599H599H
599H
4 for removal
instructions.
TUS3400
Page 21
4.4 Console Removal
WARNING!
Before removing the console, make sure all power to the system
has been disconnected. Failing to do so may cause severe
damage to the TUS3400 and injury to the user.
WARNING!
Please take antistatic precautions when working with the internal
components. The interior of the TUS3400 contains very sensitive
electronic components. These components are easily damaged
by electrostatic discharge (ESD). Before working with the internal
components, make sure all anti-static precautions described
earlier have been observed.
To access the portable computer internal components, the console must be
removed. To remove the console, please refer to Section
599H
599H599H
599H
3.5 for console removal
instructions.
4.5 SO-DIMM Replacement
Please read the warnings at the beginning of the previous section before attempting
to access any TUS3400 internal components.
To install/replace the SO-DIMM modules, please follow the steps below.
Step 1: Remove the Console (Section
600H
600H600H
600H
3.5).
Step 2: Locate the SO-DIMM module on the motherboard.
Step 3: Release the SO-DIMM module by pulling both the spring retainer clips
outward from the socket.
TUS3400
Page 22
Step 4: Grasp the SO-DIMM module by the edges and carefully pull it out of the
socket.
Step 5: Install the new SO-DIMM module by pushing it into the socket at an angle
(Figure 4-1).
Step 6: Gently push the rear of the SO-DIMM module down (Figure 4-1). The spring
retainer clips clip into place and secure the SO-DIMM module in the
socket.
Figure 4-1: SO-DIMM Module Installation
Step 7: Push the new DIMM module until it engages and the white plastic end clips
TUS3400
Page 23
A Safety Precautions
Chapter
5
TUS3400
Page 24
WARNING:
The precautions outlined in this chapter should be strictly
followed. Failure to follow these precautions may result in
permanent damage to the system.
A.1 Safety Precautions
Please follow the safety precautions outlined in the sections that follow:
A.1.1 General Safety Precautions
Please ensure the following safety precautions are adhered to at all times.
Follow the electrostatic precautions outlined below whenever the EP
series is opened.
Make sure the power is turned off and the power cord is disconnected
whenever the EP series is being installed, moved or modified.
Do not apply voltage levels that exceed the specified voltage range.
Doing so may cause fire and/or an electrical shock.
Electric shocks can occur if the chassis is opened when the system is
running.
Do not drop or insert any objects into the ventilation openings of the
portable computer
If considerable amounts of dust, water, or fluids enter the portable
computer, turn off the power supply immediately, unplug the power cord,
and contact the system vendor.
DO NOT:
o
Drop the portable computer against a hard surface.
o
Strike or exert excessive force onto the LCD panel.
o
Touch any of the LCD panels with a sharp object
o
In a site where the ambient temperature exceeds the rated
temperature
TUS3400
Page 25
A.1.2 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
system may result in permanent damage to the system and severe
injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the TUS3400. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever the TUS3400 is opened and any of the electrical
components are handled, the following anti-static precautions are strictly adhered
to.
Wear an anti-static wristband: Wearing a simple anti-static wristband
can help to prevent ESD from damaging any electrical component.
Self-grounding: Before handling any electrical component, touch any
grounded conducting material. During the time the electrical component
is handled, frequently touch any conducting materials that are
connected to the ground.
Use an anti-static pad: When configuring or working with an electrical
component, place it on an antic-static pad. This reduces the possibility
of ESD damage.
Only handle the edges of the electrical component: When handling the
electrical component, hold the electrical component by its edges.
TUS3400
Page 26
A.1.3 Product Disposal
CAUTION:
Risk of explosion if battery is replaced by and incorrect type. Only
certified engineers should replace the on-board battery.
Dispose of used batteries according to instructions and local
regulations.
Outside the European Union - If you wish to dispose of used electrical
and electronic products outside the European Union, please contact
your local authority so as to comply with the correct disposal method.
Within the European Union:
EU-wide legislation, as implemented in each Member State, requires
that waste electrical and electronic products carrying the mark (left)
must be disposed of separately from normal household waste. This
includes monitors and electrical accessories, such as signal cables
or power cords. When you need to dispose of your display products,
please follow the guidance of your local authority, or ask the shop where you
purchased the product. The mark on electrical and electronic products only applies
to the current European Union Member States.
Please follow the national guidelines for electrical and electronic product disposal.
A.2 Maintenance and Cleaning Precautions
When maintaining or cleaning the TUS3400, please follow the guidelines below.
A.2.1 Maintenance and Cleaning
Prior to cleaning any part or component of the TUS3400, please read the details
below.
Except for the LCD panel, never spray or squirt liquids directly onto any
TUS3400
Page 27
other components. To clean the LCD panel, gently wipe it with a piece of
soft dry cloth or a slightly moistened cloth.
The interior of the TUS3400 does not require cleaning. Keep fluids away
from the EP series interior.
Be cautious of all small removable components when vacuuming the
TUS3400.
Turn the TUS3400 off before cleaning it.
Never drop any objects or liquids through the openings of the TUS3400.
Be cautious of any possible allergic reactions to solvents or chemicals
used when cleaning the TUS3400.
Avoid eating, drinking and smoking within vicinity of the TUS3400.
A.2.2 Cleaning Tools
Some components in the TUS3400 may only be cleaned using a product specifically
designed for the purpose. In such case, the product will be explicitly mentioned in
the cleaning tips. Below is a list of items to use when cleaning the TUS3400.
Cloth – Although paper towels or tissues can be used, a soft, clean
piece of cloth is recommended when cleaning the TUS3400.
Water or rubbing alcohol – A cloth moistened with water or rubbing
alcohol can be used to clean TUS3400.
Using solvents – The use of solvents is not recommended when
cleaning the TUS3400 as they may damage the plastic parts.
Vacuum cleaner – Using a vacuum specifically designed for computers
is one of the best methods of cleaning the TUS3400. Dust and dirt can
restrict the airflow in the TUS3400 and cause its circuitry to corrode.
Cotton swabs - Cotton swaps moistened with rubbing alcohol or water
are excellent tools for wiping hard to reach areas.
Foam swabs - Whenever possible, it is best to use lint free swabs such
as foam swabs for cleaning.
A.2.3 Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
TUS3400
Page 28
device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide
reasonable protection against harmful interference when the equipment is operate din a
commercial environment. This equipment generates, uses, and can radiate
radiofrequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Note: The country code selection is for non-US model only and is not available to all US
model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation
channels only.
TUS3400
Page 29
B Hazardous Materials
Disclosure
Chapter
6
TUS3400
Page 30
B.1 Hazardous Material Disclosure Table for IPB Products
Certified as RoHS Compliant Under 2002/95/EC Without Mercury
The details provided in this appendix are to ensure that the product is compliant
with the Peoples Republic of China (China) RoHS standards. The table below
acknowledges the presences of small quantities of certain materials in the product,
and is applicable to China RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally
Friendly Use Period” (EFUP). This is an estimate of the number of years that these
substances would “not leak out or undergo abrupt change.” This product may
contain replaceable sub-assemblies/components which have a shorter EFUP such
as batteries and lamps. These components will be separately marked.
Please refer to the table on the next page.
TUS3400
Page 31
Part Name Toxic or Hazardous Substances and Elements
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(CR(VI))
Polybrominated
Biphenyls
(PBB)
Polybrominated
Diphenyl Ethers
(PBDE)
Housing
X
O O O O
X
Display X
O O O O
X
Printed Circuit
Board
X
O O O O
X
Metal Fasteners X
O O O O
O
Cable Assembly X
O O O O
X
Fan Assembly X
O O O O
X
Power Supply
Assemblies
X
O O O O
X
Battery O
O O O O O
O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is
below the limit requirement in SJ/T11363-2006
X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for
this part is above the limit requirement in SJ/T11363-2006
TUS3400
Page 32
此附件旨在确保本产品符合中国
此附件旨在确保本产品符合中国此附件旨在确保本产品符合中国
此附件旨在确保本产品符合中国 RoHS 标准
标准标准
标准。。。。以下表格标示此产品中某有毒物质的含量符
以下表格标示此产品中某有毒物质的含量符以下表格标示此产品中某有毒物质的含量符
以下表格标示此产品中某有毒物质的含量符
合中国
合中国合中国
合中国 RoHS 标准规定的限量要求
标准规定的限量要求标准规定的限量要求
标准规定的限量要求。
。。
。
本产品上会附有
本产品上会附有本产品上会附有
本产品上会附有”环境友好使用期限
环境友好使用期限环境友好使用期限
环境友好使用期限”的标签
的标签的标签
的标签，，，，此期限是估算这些物质
此期限是估算这些物质此期限是估算这些物质
此期限是估算这些物质”不会有泄漏或突变
不会有泄漏或突变不会有泄漏或突变
不会有泄漏或突变”
的年限
的年限的年限
的年限。。。。本产品可能包含有较短的环境友好使用期限的可替换元件
本产品可能包含有较短的环境友好使用期限的可替换元件本产品可能包含有较短的环境友好使用期限的可替换元件
本产品可能包含有较短的环境友好使用期限的可替换元件，，，，像是电池或灯管
像是电池或灯管像是电池或灯管
像是电池或灯管，，，，这这这这
些元件将会单独标示出来
些元件将会单独标示出来些元件将会单独标示出来
些元件将会单独标示出来。
。。
。
部件名称
部件名称部件名称
部件名称
有毒有害物质或元素
有毒有害物质或元素有毒有害物质或元素
有毒有害物质或元素
铅铅铅铅
(Pb)
汞汞汞汞
(Hg)
镉镉镉镉
(Cd)
六价铬
六价铬六价铬
六价铬
(CR(VI))
多溴联苯
多溴联苯多溴联苯
多溴联苯
(PBB)
多溴二苯醚
多溴二苯醚多溴二苯醚
多溴二苯醚
(PBDE)
壳体
壳体壳体
壳体
X
O O O O
X
显示
显示显示
显示
X
O O O O
X
印刷电路板
印刷电路板印刷电路板
印刷电路板
X
O O O O
X
金属螺帽
金属螺帽金属螺帽
金属螺帽
X
O O O O
O
电缆组装
电缆组装电缆组装
电缆组装
X
O O O O
X
风扇组装
风扇组装风扇组装
风扇组装
X
O O O O
X
电力供应组装
电力供应组装电力供应组装
电力供应组装
X
O O
O
O
X
电池
电池电池
电池
O
O O O O O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在
表示该有毒有害物质在该部件所有物质材料中的含量均在表示该有毒有害物质在该部件所有物质材料中的含量均在
表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下
标准规定的限量要求以下标准规定的限量要求以下
标准规定的限量要求以下。
。。
。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
表示该有毒有害物质至少在该部件的某一均质材料中的含量超出表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求
标准规定的限量要求标准规定的限量要求
标准规定的限量要求。
。。
。
Loading...