IEI Technology tKINO-AL-N2-R10, tKINO-AL-N1-R10, tKINO-AL-E3-R10, tKINO-AL-E2-R10, tKINO-AL-E1-R10 Quick Installation Manual
Page 1
1
Thin Mini-ITX SBC supports Intel® 14nm Atom™, Pentium® or
Celeron® on-board SoC with DP++, Dual PCIe GbE, USB 3.0, PCIe
Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS
tKINO-AL
Quick Installation Guide
Version 1.0
Jun 20, 2017.
Package List
tKINO-AL package includes the following items:
1 x tKINO-AL single board computer with Heatsink
1 x SATA with power cable kit (P/N: 32801-000100-300-RS )
1 x I/O Shielding
1 x QIG (Quick Installation Guide)
1 x Utility CD
1 x One key recovery CD
© 2016 Copyright by IEI Integration corp.
All rights reserved.
Page 2
2
Specifications
SoC:
Intel® Atom™ E3950 on-board SoC (up to 2.0GHz, quad-core,
2M Cache, TDP=12W )
Intel® Atom™ E3940 on-board SoC (up to 1.8GHz, quad-core,
2M Cache, TDP=9W)
Intel® Atom™ E3930 on-board SoC (up to 1.8GHz, dual-core,
2M Cache, TDP=6W)
Intel® Pentium® N4200 on-board SoC (up to 2.5GHz,
quad-core, 2M Cache, TDP=6W)
Intel® Celeron® N3350 on-board SoC (up to 2.4GHz,
dual-core, 2M Cache, TDP=6W)
BIOS: AMI UEFI BIOS
Memory:
Two 204-pin 1867/1600MHz Dual-channel DDR3L DIMMs
support up to 8GB
Graphics Engine:
Intel® HD Graphics Gen9 Low Power; 18 Execution Units
4K Codec Decode & Encode for HEVC , H.264, VP8, SVC,
MVC
Display Output:
Triple Independent Displays
1 x eDP (up to 4096x2160 @ 60Hz)
2 x DP++ (up to 4096x2160 @ 60Hz)
Ethernet: 2 x PCIe GbE LAN Realtek RTL8111GN-CG
Super I/O: Fintek F81866
External I/O Interfaces:
4 x USB 3.0
Internal I/O Interfaces:
2 x SATA 6G/s with 12/5V SATA power connector (No RAID)
2 x USB 2.0 (2x4 pin, P=2.00)
2 x RS-232/422/485 (2x5 pin, P=2.00)
4 x RS-232 (2x5 pin, P=2.00)
Page 3
3
1 x KB/MS (1x6 pin)
SMBus: 1 x SMBus (1x4 pin)
TPM: 1 x TPM connector (2x10 pin)
Audio:
Realtek ALC269 HD codec
1 x Audio Jacks (Line-out)
1 x Analog audio (2x5 pin)
1 x Speaker (1x4 pin)
Front Panel:
1 x Front panel (2x7 pin, power LED, HDD LED, speaker,
power button, reset button)
LAN LED: 2 x LAN LED (1x2 pin)
Expansion :
1 x PCIe x1
1 x Full/Half-size PCIe Mini slot (1 w/ reserved SIM holder)
1 x M.2 (B Key) (2242)(SATA port1 + USB 2.0 signal)
1 x Micro SD(Optional)
Digital I/O: 1 x 8-bit digital I/O (2x5 pin)
Fan Connector:
1 x CPU smart fan (1x4 pin)
1 x System smart fan (1x4 pin)
Power supply:
12V only DC input as Default
1 x Internal power connector (2x2 pin) (90°) (Co-lay 2 pin
Terminal block)
1 x External DC power Jackc (Ø 5.5mm)
Support AT/ATX mode
ErP/EuP Compliant
Watchdog Timer:
Software programmable supports 1~255 sec. system reset
Operating Temperature: -20°C ~ 70°C
Storage Temperature: -40°C ~ 85°C
Page 4
4
Operation Humidity: 5% ~ 95%, non-condensing
Dimension: 170mm x 170mm
Weight(GW/ NW): 1100g/ 700g
Ordering Information
tKINO-AL-N2-R10:
Thin Mini-ITX SBC supports Intel® 14nm quad-core Pentium® N4200
2.5GHz on-board SoC with DP++, Dual PCIe GbE, USB 3.0, PCIe
Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS
tKINO-AL-N1-R10:
Thin Mini-ITX SBC supports Intel® 14nm dual-core Celeron® N3350
2.4GHz on-board SoC with DP++, Dual PCIe GbE, USB 3.0, PCIe
Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS
tKINO-AL-E3-R10 *:
Thin Mini-ITX SBC supports Intel® 14nm quad-core Atom™ E3950
2.0GHz on-board SoC with DP++, Dual PCIe GbE, USB 3.0, PCIe
Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS
tKINO-AL-E2-R10 *:
Thin Mini-ITX SBC supports Intel® 14nm quad-core Atom™ E3940
1.8GHz on-board SoC with DP++, Dual PCIe GbE, USB 3.0, PCIe
Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS
tKINO-AL-E1-R10 *:
Thin Mini-ITX SBC supports Intel® 14nm dual-core Atom™ E3930
1.8GHz on-board SoC with DP++, Dual PCIe GbE, USB 3.0, PCIe
Mini, M.2, SATA 6Gb/s, COM, Audio and RoHS
32000-070301-RS: Dual-port USB cable, 210mm, P=2.0
32000-023800-RS: PS/2 KB/MS cable, 135mm, P=2.0
32205-002700-100-RS: RS-232 cable, 200mm, P=2.0
Page 5
5
TPM-IN01-R11:
20-pin Infineon TPM module, software management tool, firmware
V3.17
TPM-IN02-R11:
20-pin Infineon TPM2.0 module, software mangement tool, firmware
v5.5
Jumpers setting and connectors
LABEL
FUNCTION
J_CMOS1
Clear CMOS Switch
SW_A/T1
ATX or AT Power Select Switch
ERP1
ERP Mode Select
J_SATA1
M.2 SATA (M2_1) or SATA2 Select
TXE_IV1
Flash Descriptor Override Select
F_PANEL1
Front panel connector
JLAN_LED1, JLAN_LED2
LAN1,LAN2 Active LED Pin header
HDA1
Front Panel Audio Connector
SPK1
Speaker Connector
TRRS1
Audio Jack Microphone/Headphone
TPM1
TPM Pin Header
BT1
RTC Battery connector
CPU_FAN1, SYS_FAN1
Fan Connector
SATA_PWR1, SATA_PWR2
SATA HDD Power Connector
J_SPI1
SPI1 Flash Connector
COM1-6
Serial port connectors
KB/MS1
PS/2 Keyboard & Mouse Connector
J_SMB1
SMBUS Connector
PWR1
DC 12V System Power Input Connector
PWR2
DC 12V System Power Input Connector
EDP1
e-DP Connector for e-DP Panel
USB4-5_1
USB 2.0 Connector
DIO1
Digital I/O Connector
DIMM1
204 PIN DDR3LSO-DIMM Channel A
Page 6
6
DIMM2
204 PIN DDR3L SO-DIMM Channel B
SATA1, SATA2
Standard 7Pin SATA Connector
DP1, DP2
Standard DP++ Port 1 and Port 2
LAN1, LAN2
Standard RJ-45 With LED Connector
SD1
Standard Micro-SD Slot
MPCIE1
Standard Mini-PCIE Slot
PCIE1
Standard PCIE X 1 Slot
SIM1
Micro-SIM Card Slot
USB0-1_1, USB2-3_1
Standard Dual USB 3.0 Connector
TXE_IV1: Flash Descriptor Override Select
PIN NO.
DESCRIPTION
Short 1 - 2
No Override (Normal Operation) (default)
Short 2 - 3
Override
J_SATA1: M.2 SATA (M2_1) or SATA2 Select
PIN NO.
DESCRIPTION
Short A - B
Auto Detect M.2 SATA (default)
Short B - C
M.2 SATA Enable (SATA2 Disable)
ERP1 : ERP Mode Select
PIN NO.
DESCRIPTION
Short 1 - 2
ERP Mode Disabled(Have Standby Power) (default)
Short 2 - 3
ERP Enabled(Can used BIOS Setup to Disabled ERP)
SW_A/T1: ATX or AT Power Select Switch
PIN NO.
DESCRIPTION
Short A - B
ATX Mode (default)
Short B - C
AT Mode
J_CMOS1: Clear CMOS Switch
PIN NO.
DESCRIPTION
Open
Normal Operation (Default)
Push
Clear CMOS Setup
Page 7
7
TRRS1: Audio Jack Microphone/Headphone
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
MIC 2 Right
3
Detect+
4
Detect-
5
Left- 6 GND
SPK1: Speaker Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
L+ 2 L-
3
R- 4 R+
JLAN_LED1/JLAN_LED2: LAN1,LAN2 Active LED Pin header
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
LED+
2
LED-
F_PANEL1: Front panel connector
PIN
DESCRIPTION
PIN
DESCRIPTION
PWR
LED
1
PWR_LED+
2
SPKR+
SPKR
3
NC
4
NC
5
PWR_LED-
6
NC
PWR
BTN
7
PWR_SW+
8
SPKR-
9
PWR_SW-
10
NC
RESET
HDD
LED
11
HDD_LED+
12
RESET_SW+
13
HDD_LED-
14
RESET_SW-
HDA1: Front Panel Audio Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
MIC2-L
2
GND
3
MIC2-R
4
Pre-Sense#
5
HPOUT-R
6
MIC2-JD
7
GND
8
Key
9
HPOUT-L
10
LINE2-JD
Page 8
8
J_SPI1: SPI1 Flash Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+3.3V
4
Clock
2
CS# 5 MOSI
3
MISO 6 GND
SATA_PWR1/SATA_PWR2: SATA HDD Power Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+12V 2 GND
3
GND 4 +5V
CPU_FAN1/SYS_FAN1: Fan Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND 2 12V
3
FAN_IN
4
FANCTL
BT1: RTC Battery connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
RTC Battery+
2
RTC Battery-
TPM1: TPM Pin Header
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
Clock
2
GND
3
LFRAME#
4
Serial IRQ
5
LPC Reset
6
LAD2-
7
LAD3
8
LAD0
9
+3.3V
10
LPC Reset
11
LAD0
12
GND
13
SCL
14
SDA
15
SB3V
16
SERIRQ
17
GND
18
CLKRUN#
19
LPCPD#
20
LDRQ#
Page 9
9
PWR2: DC 12V System Power Input Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND 2 GND
3
+12V +12V
PWR1: DC 12V System Power Input Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+12V 2 GND
3
GND
J_SMB1: SMBUS Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
SMB_CLK
3
SMB_DATA
4
+5V
KB/MS1: PS/2 Keyboard & Mouse Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
4
KB_DATA
2
MS_DATA
5
KB_CLK
3
MS_CLK
6
GND
COM1-6: COM1-2 is RS-232/RS-422/RS-485 & COM3-6 is RS-232
Only.
PIN NO.
RS-232
RS-422
RS-485
1
DCD
TXD422-
TXD485-
3
RXD
TXD422+
TXD485+
5
TXD
RXD422+
7
DTR
RXD422-
9
GND
GND
GND
2
DSR
4
RTS
6
CTS
8
RI
10
GND
GND
GND
Page 10
10
EDP1: e-DP Connector for e-DP Panel
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
NC
21
LCD_VCC
2
H-GND
22
NC
3
LANE3_N
23
LCD_GND
4
LANE3_P
24
LCD_GND
5
H-GND
25
LCD_GND
6
LANE2_N
26
LCD_GND
7
LANE2_P
27
HPD
8
H-GND
28
BKLT_GND
9
LANE1_N
29
BKLT_GND
10
LANE1_P
30
BKLT_GND
11
H-GND
31
BKLT_GND
12
LANE0_N
32
BKLT_ENABLE
13
LANE0_P
33
BKLT_PWM_DIM
14
H-GND
34
NC
15
AUX_CH_P
35
NC
16
AUX_CH_N
36
BKLT_PWR
17
H-GND
37
BKLT_PWR
18
LCD_VCC
38
BKLT_PWR
19
LCD_VCC
39
BKLT_PWR
20
LCD_VCC
40
NC
USB4-5_1: USB 2.0 Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
GND
3
DATA-
4
DATA+
5
DATA+
6
DATA-
7
GND
8
+5V
Page 11
11
DIO1 :Digital I/O Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
+5V
3
D_OUT3
4
D_OUT2
5
D_OUT1
6
D_OUT0
7
D_IN3
8
D_IN2
9
D_IN1
10
D_IN0
Page 12
12
Board Layout: Jumper and Connector Locations
(Unit: mm)
Loading...