IEI Technology PPC-F15AA-H81i-P/4G/R-R10, PPC-F15AA-H81i-P/4G/PC-R10, PPC-F15AA-H81i-i3/4G/R-R10, PPC-F15AA-H81i-i3/4G/PC-R10, PPC-F15AA-H81i-i5/4G/R-R10 User Manual
...Page 1
User Manual
PPC-FxxA-H81 Panel PC
PPC-FxxA-H81 Panel PC
MODEL:
PPC-FxxA-H81
Industrial Panel PC for 4th Generation Intel® Core™,
Pentium® or Celeron® CPU, Intel® H81 Chipset, Touchscreen,
Dual PCIe Mini, USB 3.0, SATA 6Gb/s, Dual PCIe GbE,
iRIS-2400, IP 65 Compliant Front Panel and RoHS Compliant
Rev. 1.00 – September 2, 2014
Page i
Page 2
Date Version Changes
September 2, 2014 1.00 Initial release
PPC-FxxA-H81 Panel PC
Revision
Page ii
Page 3
PPC-FxxA-H81 Panel PC
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
Copyright
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page iii
Page 4
PPC-FxxA-H81 Panel PC
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 MODEL VARIATIONS................................................................................................... 3
1.3 FEATURES................................................................................................................... 4
1.4 FRONT PANEL............................................................................................................. 5
1.5 REAR PANEL............................................................................................................... 5
1.6 BOTTOM PANEL..........................................................................................................6
1.7 INTERNAL OVERVIEW................................................................................................. 8
1.8 DIMENSIONS............................................................................................................... 9
1.8.1 PPC-F15A-H81 Dimensions.............................................................................. 9
1.8.2 PPC-F17A-H81 Dimensions............................................................................ 10
1.8.3 PPC-F22A-H81 Dimensions.............................................................................11
1.8.4 PPC-F24A-H81 Dimensions............................................................................ 12
1.9 SPECIFICATIONS ....................................................................................................... 13
2 UNPACKING............................................................................................................... 15
2.1 UNPACKING.............................................................................................................. 16
2.2 PACKING LIST........................................................................................................... 17
2.3 OPTIONAL ITEMS...................................................................................................... 18
3 INSTALLATION ......................................................................................................... 19
3.1 ANTI-STATIC PRECAUTIONS...................................................................................... 20
3.2 INSTALLATION PRECAUTIONS ................................................................................... 20
3.3 PREINSTALLED COMPONENTS................................................................................... 21
3.4 INST ALLATION AND CONFIGURATION STEPS ............................................................. 21
3.5 REMOVING THE BACK COVER .................................................................................. 22
3.6 HDD INSTALLATION................................................................................................. 23
3.6.1 PPC-F15A/F17A-H81 HDD Installation ........................................................ 23
3.6.2 PPC-F22A/F24A-H81 2.5”HDD Installation................................................. 25
3.6.3 PPC-F22A/F24A-H81 3.5”HDD Installation................................................. 27
3.7 MSATA MODULE INSTALLATION.............................................................................. 29
Page iv
Page 5
PPC-FxxA-H81 Panel PC
3.8 IRIS-2400 MODULE INSTALLATION.......................................................................... 32
3.9 AT/ATX MODE SELECTION...................................................................................... 34
3.10 MOUNTING THE SYSTEM ........................................................................................ 34
3.10.1 Wall Mounting................................................................................................ 35
3.10.2 Panel Mounting.............................................................................................. 37
3.10.3 Rack and Cabinet Installation ....................................................................... 41
3.10.4 Arm Mounting ................................................................................................ 44
3.10.5 Stand Mounting.............................................................................................. 45
3.11 EXTERNAL PERIPHERAL DEVICE CONNECTION....................................................... 46
3.11.1 Audio Device Connection...............................................................................46
3.11.2 HDMI Display Device Connection ................................................................ 48
3.11.3 LAN Connection............................................................................................. 49
3.11.4 Serial Device Connection...............................................................................49
3.11.5 USB Device Connection................................................................................. 50
3.1 1.6 VGA Connector Connection........................................................................... 51
3.12 RESET THE SYSTEM................................................................................................ 52
3.13 CLEAR CMOS........................................................................................................ 53
3.14 USB POWER SELECTION ........................................................................................ 53
3.15 IPMI SETUP PROCEDURE ....................................................................................... 54
3.15.1 Managed System Hardware Setup ................................................................. 54
3.15.2 Using the IEI iMAN Web GUI........................................................................ 54
4 SYSTEM MAINTENANCE ....................................................................................... 56
4.1 SYSTEM MAINTENANCE INTRODUCTION .................................................................. 57
4.2 MOTHERBOARD REPLACEMENT ............................................................................... 57
4.3 BACK COVER REMOVAL........................................................................................... 57
4.4 SO-DIMM REPLACEMENT....................................................................................... 58
4.5 SYSTEM COOLING FAN REPLACEMENT..................................................................... 59
4.5.1 Remove the Old System Cooling Fans............................................................. 59
4.5.2 Install the New System Cooling Fans .............................................................. 60
5 BIOS SETUP................................................................................................................ 62
5.1 INTRODUCTION......................................................................................................... 63
5.1.1 Starting Setup...................................................................................................63
5.1.2 Using Setup...................................................................................................... 63
Page v
Page 6
5.1.3 Getting Help.....................................................................................................64
5.1.4 Unable to Reboot after Configuration Changes.............................................. 64
5.1.5 BIOS Menu Bar................................................................................................ 64
5.2 MAIN........................................................................................................................ 66
5.3 ADVANCED ............................................................................................................... 67
5.3.1 ACPI Settings................................................................................................... 68
5.3.2 RTC Wake Settings........................................................................................... 69
5.3.3 CPU Configuration.......................................................................................... 71
5.3.4 SATA Configuration......................................................................................... 73
5.3.5 USB Configuration........................................................................................... 74
5.3.6 F81866 Super IO Configuration...................................................................... 75
5.3.6.1 Serial Port n Configuration....................................................................... 76
5.3.7 iWDD H/W Monitor......................................................................................... 80
5.3.8 Serial Port Console Redirection...................................................................... 82
PPC-FxxA-H81 Panel PC
5.3.8.1 Console Redirection Settings.................................................................... 82
5.3.9 iEi Feature....................................................................................................... 85
5.4 CHIPSET ................................................................................................................... 86
5.4.1 PCH-IO Configuration .................................................................................... 87
5.4.1.1 PCI Express Configuration....................................................................... 89
5.4.1.2 PCH Azalia Configuration........................................................................ 90
5.4.2 System Agent (SA) Configuration .................................................................... 92
5.4.2.1 Graphics Configuration............................................................................. 93
5.4.2.2 Memory Configuration ............................................................................. 95
5.5 BOOT........................................................................................................................ 96
5.6 SECURITY................................................................................................................. 98
5.7 SAVE & EXIT............................................................................................................ 98
6 DRIVER INSTALLATION....................................................................................... 100
6.1 AVAILABLE SOFTWARE DRIVERS ............................................................................ 101
6.2 ST ARTING THE DRIVER PROGRAM .......................................................................... 101
6.3 CHIPSET DRIVER INSTALLATION............................................................................. 102
6.4 VGA DRIVER INSTALLATION.................................................................................. 106
6.5 AUDIO DRIVER INSTALLATION ................................................................................110
6.6 LAN DRIVER INSTALLATION...................................................................................112
6.7 USB 3.0 DRIVER INSTALLATION .............................................................................116
Page vi
Page 7
PPC-FxxA-H81 Panel PC
6.8 RESISTIVE TYPE TOUCHSCREEN DRIVER INSTALLATION .........................................119
6.8.1 Calibrating the Resistive Type Touchscreen................................................... 122
6.9 KEYPAD AP INSTALLATION..................................................................................... 125
7 INTERFACE CONNECTORS................................................................................. 129
7.1 PERIPHERAL INTERFACE CONNECTORS................................................................... 130
7.2 INTERNAL PERIPHERAL CONNECTORS .................................................................... 131
7.2.1 +12V Power Source Connector (CPU12V1)................................................. 133
7.2.2 ATX Power Connector (ATX1)....................................................................... 133
7.2.3 Debug Port (DBG_PORT1)........................................................................... 134
7.2.4 DIO Connector (DIO1).................................................................................. 134
7.2.5 EC Debug Port (LPT_DB1)........................................................................... 135
7.2.6 Fan Connectors (CPU_FAN1/SYS_FAN1/SYS_FAN2) .................................. 135
7.2.7 Front Panel Connector (F_PANEL1)............................................................. 136
7.2.8 I2C Connector (CN5) ..................................................................................... 136
7.2.9 IPMI Active LED Connector (LEDCN1)....................................................... 136
7.2.10 Keyboard and Mouse Connector (KBMS1)................................................. 137
7.2.11 Keypad Connector (HOTKEY_CN1) ........................................................... 137
7.2.12 LAN Active LED Connectors (LED_LAN1/LED_LAN2)............................. 137
7.2.13 LVDS Connector (LVDS1)........................................................................... 138
7.2.14 Panel Power Supply Connector (INVERTER1)........................................... 138
7.2.15 PCIe Mini (MINI_PCIE1) and mSATA (MSATA1) Card Slots.....................139
7.2.16 Resistive Touchscreen Connector (TOUCH1) ............................................. 140
7.2.17 SATA 6Gb/s Connectors (S_ATA1/S_ATA2)................................................. 140
7.2.18 SATA Power Connectors (SATA_PWR1/SATA_PWR2)................................ 141
7.2.19 SMBus Connector (CN1) ............................................................................. 141
7.2.20 SPI Flash Connector (JSPI1)....................................................................... 141
7.2.21 SPI Flash (EC) Connector (JSPI2).............................................................. 142
7.2.22 U3 Firmware Programming Connector (JP1)............................................. 142
7.2.23 USB 2.0 Connector (USB1) ......................................................................... 142
7.3 EXTERNAL INTERFACE PANEL CONNECTORS .......................................................... 143
7.3.1 HDMI Connector (HDMI1)........................................................................... 143
7.3.2 RS-232 Serial Ports (COM1/COM2, COM3/COM4).................................... 144
7.3.3 USB 2.0 Connectors (USB_CON1)................................................................ 144
7.3.4 RJ-45 GbE and USB 2.0 Connectors (LAN2_USB2)..................................... 144
Page vii
Page 8
7.3.5 RJ-45 GbE and USB 3.0 Connectors (LAN1_USB1)..................................... 145
7.3.6 RS-422/485 Serial Port and VGA Connector (COM5/VGA1)....................... 146
7.4 PRECONFIGURED JUMPERS ..................................................................................... 146
7.4.1 Flash Descriptor Security Override Jumper (J_FLASH1)............................ 147
7.4.2 LVDS Panel Resolution Selection Switch (JLCD_SET1) .............................. 147
7.4.3 Panel Voltage Selection Jumper (JLCD_PWR1) ........................................... 148
7.4.4 Touchscreen Selection Jumper (JTOUCH1).................................................. 148
A BIOS CONFIGURATION OPTIONS..................................................................... 149
A.1 BIOS CONFIGURATION OPTIONS........................................................................... 150
B SAFETY PRECAUTIONS....................................................................................... 152
B.1 SAFETY PRECAUTIONS........................................................................................... 153
B.1.1 General Safety Precautions........................................................................... 153
B.1.2 Anti-static Precautions.................................................................................. 154
PPC-FxxA-H81 Panel PC
B.1.3 Product Disposal........................................................................................... 154
B.2 MAINTENANCE AND CLEANING PRECAUTIONS ...................................................... 155
B.2.1 Maintenance and Cleaning............................................................................ 155
B.2.2 Cleaning Tools............................................................................................... 156
C WATCHDOG TIMER .............................................................................................. 157
D HAZARDOUS MATERIALS DISCLOSURE....................................................... 160
D.1 HAZARDOUS MATERI AL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 161
Page viii
Page 9
PPC-FxxA-H81 Panel PC
List of Figures
Figure 1-1: PPC-FxxA-H81 Panel PC ............................................................................................2
Figure 1-2: Front View....................................................................................................................5
Figure 1-3: PPC-F15A-H81 Rear View...........................................................................................6
Figure 1-4: Bottom View ................................................................................................................7
Figure 1-5: PPC-F15A-H81 Internal Components........................................................................8
Figure 1-6: PPC-F22A-H81 Internal Components........................................................................8
Figure 1-7: PPC-F15A-H81 Dimensions (mm)..............................................................................9
Figure 1-8: PPC-F17A-H81 Dimensions (mm)............................................................................10
Figure 1-9: PPC-F22A-H81 Dimensions (mm)............................................................................11
Figure 1-10: PPC-F24A-H81 Dimensions (mm)..........................................................................12
Figure 3-1: PPC-F15A-H81 Back Cover Retention Screws.......................................................22
Figure 3-2: PPC-F15A/F17A-H81 HDD Bracket Retention Screws...........................................23
Figure 3-3: HDD Retention Screws.............................................................................................24
Figure 3-4: Replacing the PPC-F15A/F17A-H81 HDD Bracket .................................................24
Figure 3-5: PPC-F22A/F24A-H81 HDD Bracket Retention Screws...........................................25
Figure 3-6: Connecting the Hard Drive to the HDD Bracket.....................................................26
Figure 3-7: 2.5” HDD Retention Screws .....................................................................................26
Figure 3-8: Replacing the PPC-F22A/F24A-H81 HDD Bracket .................................................27
Figure 3-9: Connecting the Hard Drive to the HDD Bracket.....................................................28
Figure 3-10: 3.5” HDD Retention Screws ...................................................................................28
Figure 3-11: Replacing the PPC-F22A/F24A-H81 HDD Bracket...............................................29
Figure 3-12: PCIe Mini Card Slot which supports mSATA.......................................................30
Figure 3-13: Removing the Retention Screws...........................................................................30
Figure 3-14: Inserting the PCIe Mini Card into the Slot at an Angle........................................31
Figure 3-15: Securing the PCIe Mini Card..................................................................................32
Figure 3-16: iRIS-2400 Module Slot.............................................................................................33
Figure 3-17: iRIS-2400 Module Installation................................................................................33
Figure 3-18: AT/ATX Mode Selection..........................................................................................34
Figure 3-19: Wall-mounting Bracket...........................................................................................35
Figure 3-20: Mount the Chassis..................................................................................................36
Figure 3-21: Secure the Chassis.................................................................................................37
Page ix
Page 10
Figure 3-22: PPC-F15A-H81 Mounting Bracket Installation .....................................................38
Figure 3-23: PPC-F15A-H81 Panel Cutout Dimensions............................................................38
Figure 3-24: PPC-F17A-H81 Panel Cutout Dimensions............................................................39
Figure 3-25: PPC-F22A-H81 Panel Cutout Dimensions............................................................39
Figure 3-26: PPC-F24A-H81 Panel Cutout Dimensions............................................................40
Figure 3-27: Tighten the Mounting Clamp Screws....................................................................41
Figure 3-28: The Rack/Cabinet Bracket......................................................................................42
Figure 3-29: Secure the Rack/Cabinet Bracket..........................................................................43
Figure 3-30: Install into a Rack/Cabinet .....................................................................................44
Figure 3-31: Arm Mounting Retention Screw Holes..................................................................45
Figure 3-32: Stand Mounting Retention Screw Holes...............................................................46
Figure 3-33: Audio Connector.....................................................................................................47
Figure 3-34: HDMI Connection....................................................................................................48
Figure 3-35: LAN Connection......................................................................................................49
PPC-FxxA-H81 Panel PC
Figure 3-36: RS-232 Serial Device Connector ...........................................................................50
Figure 3-37: USB Device Connection.........................................................................................51
Figure 3-38: VGA Connector .......................................................................................................52
Figure 3-39: Reset Button Location............................................................................................52
Figure 3-40: Clear CMOS Button Location.................................................................................53
Figure 3-41: IEI iMAN Web Address............................................................................................55
Figure 3-42: IEI iMAN Web GUI....................................................................................................55
Figure 4-1: SO-DIMM Module Locations.....................................................................................58
Figure 4-2: SO-DIMM Module Installation...................................................................................59
Figure 4-3: System Cooling Fans Motherboard Connectors ...................................................60
Figure 4-4: System Cooling Fan Retention Screws..................................................................60
Figure 6-1: Drivers..................................................................................................................... 102
Figure 6-2: Chipset Driver Welcome Screen........................................................................... 103
Figure 6-3: Chipset Driver License Agreement...................................................................... 104
Figure 6-4: Chipset Driver Read Me File ................................................................................. 104
Figure 6-5: Chipset Driver Setup Operations ......................................................................... 105
Figure 6-6: Chipset Driver Installation Finish Screen............................................................ 106
Figure 6-7: VGA Driver README FILE..................................................................................... 107
Figure 6-8: VGA Driver Screen................................................................................................. 107
Figure 6-9: VGA Driver Welcome Screen................................................................................ 108
Figure 6-10: VGA Driver License Agreement.......................................................................... 108
Page x
Page 11
PPC-FxxA-H81 Panel PC
Figure 6-11: VGA Driver Readme File Information................................................................. 109
Figure 6-12: VGA Driver Setup Progress................................................................................ 109
Figure 6-13: VGA Driver Installation Finish Screen............................................................... 110
Figure 6-14: Audio Driver Welcome Screen............................................................................ 111
Figure 6-15: Audio Driver Installation...................................................................................... 111
Figure 6-16: Audio Driver Installation Complete.................................................................... 112
Figure 6-17: LAN Driver Welcome Screen .............................................................................. 113
Figure 6-18: LAN Driver License Agreement.......................................................................... 113
Figure 6-19: LAN Driver Setup Options................................................................................... 114
Figure 6-20: LAN Driver Installation ........................................................................................ 115
Figure 6-21: LAN Driver Installation Complete....................................................................... 115
Figure 6-22: USB 3.0 Driver Welcome Screen........................................................................ 116
Figure 6-23: USB 3.0 Driver License Agreement.................................................................... 117
Figure 6-24: USB 3.0 Driver Read Me File............................................................................... 118
Figure 6-25: USB 3.0 Driver Setup Operations....................................................................... 118
Figure 6-26: USB 3.0 Driver Installation Finish Screen ......................................................... 119
Figure 6-27: Welcome Screen .................................................................................................. 120
Figure 6-28: Touchscreen Driver License Agreement........................................................... 120
Figure 6-29: Choose Destination Folder ................................................................................. 121
Figure 6-30: Setup Status ......................................................................................................... 121
Figure 6-31: Select Touch Features......................................................................................... 122
Figure 6-32: Touchscreen Driver Installation Finish Screen ................................................ 122
Figure 6-33: Select Control Panel............................................................................................ 123
Figure 6-34: Touchscreen Control Panel ................................................................................ 123
Figure 6-35: Select Calibration Type ....................................................................................... 124
Figure 6-36: Calibration Window.............................................................................................. 124
Figure 6-37: Keypad AP Welcome Screen.............................................................................. 125
Figure 6-38: Select Installation Folder..................................................................................... 126
Figure 6-39: Confirm Installation ............................................................................................. 126
Figure 6-40: Keypad AP Installation Complete....................................................................... 127
Figure 6-41: Keypad AP Installation Complete....................................................................... 127
Figure 6-42: Keypad AP............................................................................................................ 128
Figure 7-1: Main Board Layout Diagram (Front Side)............................................................ 130
Figure 7-2: Main Board Layout Diagram (Solder Side).......................................................... 131
Page xi
Page 12
PPC-FxxA-H81 Panel PC
List of Tables
Table 1-1: Model Variations...........................................................................................................4
Table 1-2: System Specifications................................................................................................14
Table 2-1: Packing List.................................................................................................................17
Table 2-2: Optional Items.............................................................................................................18
Table 3-1: BIOS Options and Configured USB Ports................................................................53
Table 3-2: USB Power Source Setup..........................................................................................53
Table 5-1: BIOS Navigation Keys................................................................................................64
Table 5-2: BIOS Options and Configured USB Ports................................................................88
Table 7-1: Peripheral Interface Connectors............................................................................ 132
Table 7-2: +12V Power Source Connector ( CPU12V1) Pinouts ........................................... 133
Table 7-3: ATX Power Connector (ATX1) Pinouts.................................................................. 133
Table 7-4: Debug Port (DBG_PORT1) Pinouts........................................................................ 134
Table 7-5: DIO Connector (DIO1) Pinouts ............................................................................... 134
Table 7-6: EC Debug Port (LPT_DB1) Pinouts........................................................................ 135
Table 7-7: Fan Connector Pinouts........................................................................................... 135
Table 7-8: Front Panel Connector (F_PANEL1) Pinouts........................................................ 136
Table 7-9: I2C Connector (CN5) Pinouts.................................................................................. 136
Table 7-10: IPMI Active LED Connector (LEDCN1) Pinouts.................................................. 136
Table 7-11: Keyboard and Mouse Connector (KBMS1) Pinouts........................................... 137
Table 7-12: Keypad Connector (HOTKEY_CN1) Pinouts....................................................... 137
Table 7-13: LAN Active LED Connectors (LED_LAN1/LED_LAN2) Pinouts........................ 137
Table 7-14: LVDS Connector (LVDS1) Pinouts....................................................................... 138
Table 7-15: Panel Power Supply Connector (INVERTER1) Pinouts..................................... 138
Table 7-16: PCIe Mini (MINI_PCIE1) and mSATA (MSATA1) Card Pinouts.......................... 139
Table 7-17: Resistive Touchscreen Connector (TOUCH1) Pinouts...................................... 140
Table 7-18: SATA 6Gb/s Connectors (S_ATA1/S_ATA2) Pinouts ........................................ 140
Table 7-19: SATA Power Connectors (SATA_PWR1/SATA_PWR2) Pinouts....................... 141
Table 7-20: SMBus Connector (CN1) Pinouts......................................................................... 141
Table 7-21: SPI Flash Connector (JSPI1) Pinouts.................................................................. 141
Table 7-22: SPI Flash (EC) Connector (JSPI2) Pinouts.......................................................... 142
Table 7-23: U3 Firmware Programming Connector (JP1) Pinouts ....................................... 142
Page xii
Page 13
PPC-FxxA-H81 Panel PC
Table 7-24: USB 2.0 Connector (USB1) Pinouts..................................................................... 142
Table 7-25: Rear Panel Connectors......................................................................................... 143
Table 7-26: HDMI Connector (HDMI1) Pinouts........................................................................ 144
Table 7-27: RS-232 Serial Port Pinouts ................................................................................... 144
Table 7-28: USB 2.0 Connector (USB_CON1) Pinouts........................................................... 144
Table 7-29: RJ-45 GbE Connector (LAN2_USB2) Pinouts..................................................... 144
Table 7-30: USB 2.0 Connector (LAN2_USB2) Pinouts ......................................................... 145
Table 7-31: RJ-45 GbE Connector (LAN1_USB1) Pinouts..................................................... 145
Table 7-32: USB 3.0 Connector (LAN1_USB1) Pinouts ......................................................... 145
Table 7-33: RS-422/485 Serial Port (COM5) Pinouts .............................................................. 146
Table 7-34: VGA Connector (VGA1) Pinouts .......................................................................... 146
Table 7-35: Preconfigured Jumpers ........................................................................................ 147
Table 7-36: Flash Descriptor Security Override Jumper (J_FLASH1) Settings.................. 147
Table 7-37: LVDS Panel Resolution Selection........................................................................ 147
Table 7-38: Panel Voltage Selection Jumper (JLCD_PWR1) Settings ................................. 148
Table 7-39: Touchscreen Selection Jumper (JTOUCH1) Settings........................................ 148
Page xiii
Page 14
PPC-FxxA-H81 Panel PC
Chapter
1
1 Introduction
Page 1
Page 15
1.1 Overview
Figure 1-1: PPC-FxxA-H81 Panel PC
PPC-FxxA-H81 Panel PC
The PPC-FxxA-H81 is a heavy industrial panel PC with rugged and trendy design which
can be applied in harsh industrial environments and enriches aesthetic experience at the
same time. The PPC-FxxA-H81 not only provides all the features of a PC, but also
combines with resistive/projected capacitive touchscreen for mouse and keyboard free
data input.
With the latest Intel® H81 platform, the PPC-FxxA-H81 offers various CPU choices and
equips with SATA 6Gb/s interface, supporting both SATA HDD and SSD. In addition, the
PPC-FxxA-H81 features Intelligent Platform Management Interface 2.0 (IPMI 2.0) that
helps lower the overall costs of server management by enabling users to maximize IT
resource, save time and manage multiple systems. The PPC-FxxA-H81 supports IPMI 2.0
through the optional iRIS-2400 module.
The major external device connections include USB 3.0, USB 2.0, serial port, VGA and
HDMI connectors. Furthermore, the PPC-FxxA-H81 has two full-size/half-size PCIe Mini
card slots, allowing installation of a wide variety of PCIe Mini card solutions, such as a
Wi-Fi module and mSATA module.
Page 2
Page 16
PPC-FxxA-H81 Panel PC
1.2 Model Variations
The model numbers and model variations are listed below.
Model CPU Touchscreen Power Screen
PPC-F15AA-H81i-P/4G/R-R10 Resistive AC input 15”
PPC–F15AA–H81i-P/4G/PC-R10
PPC–F15AA–H81i-i3/4G/R-R10 Resistive AC input 15”
PPC–F15AA–H81i-i3/4G/PC-R10
PPC–F15AA–H81i-i5/4G/R-R10 Resistive AC input 15”
PPC–F15AA–H81i-i5/4G/PC-R10
PPC–F15AD–H81i/R-R10 Resistive DC input 15”
PPC–F15AD–H81i/PC-R10
PPC-F17AA-H81i-P/4G/R-R10 Resistive AC input 17”
PPC–F17AA–H81i-P/4G/PC-R10
PPC–F17AA–H81i-i3/4G/R-R10 Resistive AC input 17”
PPC–F17AA–H81i-i3/4G/PC-R10
PPC–F17AA–H81i-i5/4G/R-R10 Resistive AC input 17”
PPC–F17AA–H81i-i5/4G/PC-R10
Intel® Pentium® G3220
(dual-core, 3.0 GHz,
max. TDP=53 W)
Intel® Core™ i3-4330
(dual-core, 3.5 GHz,
max. TDP=54 W)
Intel® Core™ i5-4570S
(quad -core, up to 3.6 GHz,
max. TDP=65 W)
N/A
Intel® Pentium® G3220
(dual-core, 3.0 GHz,
max. TDP=53 W)
Intel® Core™ i3-4330
(dual-core, 3.5 GHz,
max. TDP=54 W)
Intel® Core™ i5-4570S
(quad-core, up to 3.6 GHz,
max. TDP=65 W)
Projected capacitive
Projected capacitive
Projected capacitive
Projected capacitive DC input 15”
Projected capacitive
Projected capacitive
Projected capacitive
AC input 15”
AC input 15”
AC input 15”
AC input 17”
AC input 17”
AC input 17”
PPC–F17AD–H81i/R-R10 Resistive DC input 17”
N/A
PPC–F17AD–H81i/PC-R10
PPC–F22AA–H81i-P/4G/PC-R10
PPC–F22AA–H81i-i3/4G/PC-R10
PPC–F22AA–H81i-i5/4G/PC-R10
PPC–F22AD–H81i/PC-R10
Intel® Pentium® G3220
(dual-core, 3.0 GHz,
max. TDP=53 W)
Intel® Core™ i3-4330
(dual-core, 3.5 GHz,
max. TDP=54 W)
Intel® Core™ i5-4570S
(quad-core, up to 3.6 GHz,
max. TDP=65 W)
N/A
Projected capacitive DC input 17”
Projected capacitive AC input 21.5”
Projected capacitive AC input 21.5”
Projected capacitive AC input 21.5”
Projected capacitive DC input 21.5”
Page 3
Page 17
PPC-FxxA-H81 Panel PC
Model CPU Touchscreen Power Screen
Intel® Pentium® G3220
PPC–F24AA–H81i-P/4G/PC-R10
PPC–F24AA–H81i-i3/4G/PC-R10
PPC–F24AA–H81i-i5/4G/PC-R10
(dual-core, 3.0 GHz,
max. TDP=53 W)
Intel® Core™ i3-4330
(dual-core, 3.5 GHz,
max. TDP=54 W)
Intel® Core™ i5-4570S
(quad-core, up to 3.6 GHz,
max. TDP=65 W)
Projected capacitive AC input 24”
Projected capacitive AC input 24”
Projected capacitive AC input 24”
PPC–F24AD–H81i/PC-R10
Table 1-1: Model Variations
1.3 Features
Some of the features of the PPC-FxxA-H81 panel PC include:
Supports iRIS remote management solution
Robust aluminum IP 65 compliant front bezel
Aesthetic ultra-thin bezel for seamless panel mount installation
Supports LGA1150 Intel® 4th generation Core™, Pentium® and Celeron®
processors
Intel® H81 chipset
Two 204-pin DDR3 SO-DIMM slots (system max. 16 GB)
Two full-size/half-size PCIe Mini card slots (one supports mSATA SSD)
Supports SATA 6Gb/s interface for both SATA HDD and SSD
Dual video output: HDMI and VGA
N/A
Projected capacitive DC input 24”
Page 4
Optional PCIe Mini 802.11b/g/n wireless module
Rich I/O interfaces, including four RS-232, one RS-422/485, two USB 3.0,
four USB 2.0, line-out and mic-in audio jacks
RoHS compliant
Page 18
PPC-FxxA-H81 Panel PC
1.4 Front Panel
The front side of the PPC-FxxA-H81 (Figure 1-2) is a flat panel LCD screen surrounded
by an aluminum frame.
Figure 1-2: Front View
1.5 Rear Panel
The rear panel has a fan vent, four VESA 100x100 mounting holes and several retention
screw holes. The VESA 100x100 mounting holes are circled in
NOTE:
The PPC-F24A-H81 supports also VESA 100x200 mounting standard.
Figure 1-3.
Page 5
Page 19
Figure 1-3: PPC-F15A-H81 Rear View
1.6 Bottom Panel
PPC-FxxA-H81 Panel PC
The bottom panel has the following interfaces:
1 x Power input connector
1 x Power switch
2 x USB 3.0 connectors
4 x USB 2.0 connectors
1 x Reset button
1 x Clear CMOS button
2 x RJ-45 GbE connectors
4 x RS-232 connectors (COM1, COM2, COM3 and COM4)
1 x RS-422/485 connector (COM5)
1 x Line-out jack
1 x Mic-in jack
1 x VGA connector
1 x HDMI connector
1 x AT/ATX switch
Page 6
Page 20
PPC-FxxA-H81 Panel PC
Figure 1-4: Bottom View
Page 7
Page 21
1.7 Internal Overview
An overview picture of the internal components is shown in 6Figure 1-6 below.
PPC-FxxA-H81 Panel PC
Figure 1-5: PPC-F15A-H81 Internal Components
Figure 1-6: PPC-F22A-H81 Internal Components
Page 8
Page 22
PPC-FxxA-H81 Panel PC
1.8 Dimensions
1.8.1 PPC-F15A-H81 Dimensions
Figure 1-7: PPC-F15A-H81 Dimensions (mm)
Page 9
Page 23
1.8.2 PPC-F17A-H81 Dimensions
PPC-FxxA-H81 Panel PC
Figure 1-8: PPC-F17A-H81 Dimensions (mm)
Page 10
Page 24
PPC-FxxA-H81 Panel PC
1.8.3 PPC-F22A-H81 Dimensions
Figure 1-9: PPC-F22A-H81 Dimensions (mm)
Page 11
Page 25
1.8.4 PPC-F24A-H81 Dimensions
PPC-FxxA-H81 Panel PC
Figure 1-10: PPC-F24A-H81 Dimensions (mm)
Page 12
Page 26
PPC-FxxA-H81 Panel PC
1.9 Specifications
The technical specifications for the PPC-FxxA-H81 system are listed in Table 1-2.
PPC-F15A-H81 PPC-F17A-H81 PPC-F22A-H81 PPC-F24A-H81
LCD Display
Max. Resolution
Brightness
Contrast Ratio
LCD Color
Pixel Pitch (mm)
Viewing Angle (H-V)
Backlight MTBF
SBC Model
CPU Supported
Chipset
Memory
Touchscreen
15” (4:3) 17” (5:4) 21.5” (16:9) 24” (16:9)
1024 (W) x 768 (H) 1280 (W) x 1024 (H) 1920 (W) x 1080 (H) 1920 (W) x 1080 (H)
400 cd/m
700:1 1000:1 1000:1 3000:1
16.2M 16.7M 16.7M 16.7M
0.29 x 0.29 0.26 x 0.26 0.25 x 0.25 0.28 x 0.28
160°/140° 170°/160° 178°/178° 178°/178°
50,000 hours 50,000 hours 30,000 hours 30,000 hours
PPCMB-H81
LGA1150 Intel® 4th generation Core™/Pentium®/Celeron® CPU, supporting
TDP up to 65 W
Intel® H81
Two 204-pin DDR3 SO-DIMM slots (system max. 16 GB)
5-wire resistive type or projected
capacitive type
2
350 cd/m2 250 cd/m2 250 cd/m2
Projected capacitive type
Drive Bay
iRIS Remote
Management Solution
Expansion
Mounting
One 2.5” HDD/SSD drive bay One 2.5”/3.5” HDD/SSD drive bay
iRIS-2400 slot
Two full-size/half-size PCIe Mini card slots (one supports mSATA)
VESA 100 mm x
100 mm
VESA 100 mm x
200 mm
Panel, wall, stand
and arm
VESA 100 mm x 100 mm
Panel, wall, rack, stand and arm
VESA 100 mm x
100 mm
Panel, wall, stand
and arm
Page 13
Page 27
PPC-F15A-H81 PPC-F17A-H81 PPC-F22A-H81 PPC-F24A-H81
PPC-FxxA-H81 Panel PC
Construction
Material
Enclosure Color
I/O Ports, Switches
and Buttons
Aluminum front cover and sheet metal rear cover
Black
2 x USB 3.0
4 x USB 2.0
4 x RS-232 (COM1 ~ COM4)
1 x RS-232/422/485 (COM5)
1 x HDMI connector
1 x VGA connector
2 x RJ-45 GbE connectors (one supports iRIS)
2 x Audio jacks (Line-out and Mic-in)
1 x Power switch
1 x Clear CMOS button
1 x Reset button
1 x AT/ATX switch
Power Supply
Operating
Temperature
(With air flow)
Storage Temperature
Humidity
IP Level
Safety and EMC
Dimensions
(H x W x D) (mm)
Weight (Net/Gross)
Table 1-2: System Specifications
AC input (AA model): ACE-A622A , 220 W
DC input (AD model): ACE-4520C, 250 W
-10ºC ~ 50ºC
-20ºC ~ 60ºC
10% ~ 95%, non-condensing
IP 65 compliant front panel
CE, FCC
303 x 378.5 x
65.7
5.6 kg/8.3 kg 7.5 kg/10.7 kg 10.1 kg/14.4 kg 10.5 kg/14.8 kg
341.4 x 408.4 x
73.8
358.4 x 550.4 x
382 x 600 x 71.7
71.2
Page 14
Page 28
PPC-FxxA-H81 Panel PC
Chapter
2
2 Unpacking
Page 15
Page 29
2.1 Unpacking
To unpack the panel PC, follow the steps below:
WARNING!
The front side LCD screen has a protective plastic cover stuck to the
screen. Only remove the plastic cover after the panel PC has been properly
installed. This ensures the screen is protected during the installation
process.
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
external (second) box.
PPC-FxxA-H81 Panel PC
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
internal (first) box.
Step 4: Lift the monitor out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Pull the plastic cover off the panel PC.
Step 7: Make sure all the components listed in the packing list are present. Step 0:
Page 16
Page 30
PPC-FxxA-H81 Panel PC
2.2 Packing List
The PPC-FxxA-H81 panel PC is shipped with the following components:
Quantity Item Image
1 PPC-FxxA-H81
1 Power cord
(P/N: varies by regions)
1 Screw kit
1
Touch pen (P/N: 43125-0002C0-00-RS)
(resistive type models only)
1 User manual and driver CD
1 One Key Recovery CD
Table 2-1: Packing List
If any of the above items are missing or damaged, contact the distributor or sales
representative immediately.
Page 17
Page 31
2.3 Optional Items
The following items are optional accessories for the PPC-FxxA-H81:
PPC-FxxA-H81 Panel PC
Item
Arm
Panel mounting kit
Rack mounting kit
Stand
Wall mounting kit
Wi-Fi kit
iRIS remote
management module
Table 2-2: Optional Items
PPC-F15A-H81 PPC-F17A-H81 PPC-F22A-H81 PPC-F24A-H81
FRK15-R10 FRK17-R10 N/A
STAND-A19
STAND-B19
ARM-31
FPK-04-R10 FPK-05-R10 FPK-06-R10
STAND-C19
STAND-A26
STAND-A26
WK-190MS-R10
PPC-WL-KIT03-R10
iRIS-2400-R10
Page 18
Page 32
PPC-FxxA-H81 Panel PC
3 Installation
Chapter
3
Page 19
Page 33
3.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the maintenance of the EP
series may result in permanent damage to the EP series and severe
injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the PPC-FxxA-H81. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever the PPC-FxxA-H81 is accessed internally, or any other
electrical component is handled, the following anti-static precautions are strictly adhered
to.
PPC-FxxA-H81 Panel PC
Wear an anti-static wristband: - Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: - Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: - When configuring the PPC-FxxA-H81, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
PPC-FxxA-H81.
Only handle the edges of the PCB: - When handling the PCB, hold the PCB
by the edges.
3.2 Installation Precautions
When installing the panel PC, please follow the precautions listed below:
Power turned off: When installing the panel PC, make sure the power is off.
Failing to turn off the power may cause severe injury to the body and/or
damage to the system.
Page 20
Certified Engineers: Only certified engineers should install and modify
onboard functionalities.
Page 34
PPC-FxxA-H81 Panel PC
Mounting: The PPC-FxxA-H81 is a heavy device. When mounting the system
onto a rack, panel, wall or arm, please make sure that at least two people are
assisting with the procedure.
Anti-static Discharge : If a user open the rear panel of the panel PC, to
configure the jumpers or plug in added peripheral devices, ground themselves
first and wear and anti-static wristband.
3.3 Preinstalled Components
The following components are all preinstalled.
Motherboard
TFT LCD
Touchscreen
Power supply
System cooling fans
Preinstalled OEM customizations may include the following.
CPU
DDR3 memory module
HDD
Wi-Fi module
3.4 Installation and Configuration Steps
The following installation steps must be followed.
Step 1: Unpack the PPC-FxxA-H81.
Step 2: Install HDD, mSATA SSD and iRIS-2400 module.
Step 3: Mount the PPC-FxxA-H81 panel PC.
Step 4: Connect peripheral devices to the bottom panel of the PPC-FxxA-H81.
Step 5: Configure the system.Step 0:
Page 21
Page 35
3.5 Removing the Back Cover
Remove all the retention screws on the back cover. Lift the cover up to remove.
NOTE:
The number of retention screws on the back cover varies by models.
PPC-FxxA-H81 Panel PC
Page 22
Figure 3-1: PPC-F15A-H81 Back Cover Retention Screws
Page 36
PPC-FxxA-H81 Panel PC
3.6 HDD Installation
3.6.1 PPC-F15A/F17A-H81 HDD Installation
To install a 2.5” HDD into the PPC-F15A/F17A-H81, please follow the steps below:
Step 1: Remove the back cover. See Section
63.5.
Step 2: Remove the HDD bracket from the PPC-F15A/F17 A-H81. The HDD bracket is
secured on the panel PC with four retention screws (
6Figure 3-2). Remove the
four retention screws and lift the bracket off the panel PC.
Figure 3-2: PPC-F15A/F17A-H81 HDD Bracket Retention Screws
Step 3: Attach the hard drive to the bracket. To do this, slide the hard drive onto the
bracket until it connects with the SATA connector at the back.
Step 4: Secure the hard drive to the bracket. Secure the hard drive to the bracket with
four retention screws (
Figure 3-3).
Page 23
Page 37
Figure 3-3: HDD Retention Screws
Step 5: Reinstall the HDD bracket into the PPC-FxxA-H81 and fasten the four hard drive
PPC-FxxA-H81 Panel PC
bracket screws (
Figure 3-4: Replacing the PPC-F15A/F17A-H81 HDD Bracket
Figure 3-4).Step 0:
Page 24
Page 38
PPC-FxxA-H81 Panel PC
3.6.2 PPC-F22A/F24A-H81 2.5＂HDD Installation
The PPC-F22A/F24A-H81 allows installation of either a 2.5” or 3.5” HDD. To install a 2.5”
HDD into the PPC-F22A/F24A-H81, please follow the steps below:
Step 1: Remove the back cover. See Section
Step 2: Remove the HDD bracket from the PPC-F22A/F24 A-H81. The HDD bracket is
secured on the panel PC with four retention screws (
four retention screws and lift the bracket off the panel PC.
63.5.
Figure 3-5). Remove the
Figure 3-5: PPC-F22A/F24A-H81 HDD Bracket Retention Screws
Page 25
Page 39
Step 3: Attach the hard drive to the bracket. To do this, slide the hard drive onto the
PPC-FxxA-H81 Panel PC
bracket until it connects with the SATA connector at the back (
Figure 3-6: Connecting the Hard Drive to the HDD Bracket
Step 4: Secure the hard drive to the bracket. Secure the hard drive to the bracket with
four retention screws as shown in
Figure 3-7.
Figure 3-6).
Page 26
Figure 3-7: 2.5” HDD Retention Screws
Step 5: Reinstall the HDD bracket into the PPC-FxxA-H81 and fasten the four hard drive
bracket screws (
Figure 3-8).Step 0:
Page 40
PPC-FxxA-H81 Panel PC
Figure 3-8: Replacing the PPC-F22A/F24A-H81 HDD Bracket
3.6.3 PPC-F22A/F24A-H81 3.5＂HDD Installation
The PPC-F22A/F24A-H81 allows installation of either a 2.5” or 3.5” HDD. To install a 3.5”
HDD into the PPC-F22A/F24A-H81, please follow the steps below:
Step 1: Remove the back cover. See Section
Step 2: Remove the HDD bracket from the PPC-F22A/F24 A-H81. The HDD bracket is
secured on the panel PC with four retention screws (
four retention screws and lift the bracket off the panel PC.
63.5.
Figure 3-5). Remove the
Page 27
Page 41
Step 3: Attach the hard drive to the bracket. To do this, slide the hard drive onto the
PPC-FxxA-H81 Panel PC
bracket until it connects with the SATA connector at the back (
Figure 3-9: Connecting the Hard Drive to the HDD Bracket
Step 4: Secure the hard drive to the bracket. Secure the hard drive to the bracket with
four retention screws as shown in
Figure 3-10.
Figure 3-9).
Page 28
Figure 3-10: 3.5” HDD Retention Screws
Step 5: Reinstall the HDD bracket into the PPC-FxxA-H81 and fasten the four hard drive
bracket screws (
Figure 3-11).Step 0:
Page 42
PPC-FxxA-H81 Panel PC
Figure 3-11: Replacing the PPC-F22A/F24A-H81 HDD Bracket
3.7 mSATA Module Installation
One of the PCIe Mini card slots on the motherboard of the PPC-FxxA-H81 supports
mSATA module. To install an mSATA module, please follow the steps below.
Step 1: Remove the back cover. See Section
Step 2: Locate the PCIe Mini card slot which supports mSATA. The location of the
PCIe Mini card slot is shown in
63.5.
Figure 3-12.
Page 29
Page 43
PPC-FxxA-H81 Panel PC
Figure 3-12: PCIe Mini Card Slot which supports mSATA
Step 3: Remove the retention screws. Remove the two retention screws as shown in
Figure 3-13.
Page 30
Figure 3-13: Removing the Retention Screws
Page 44
PPC-FxxA-H81 Panel PC
Step 4: Insert into the socket at an angle. Line up the notch on the card with the notch
on the slot. Slide the PCIe Mini card into the socket at an angle of about 20º
Figure 3-14).
(
Figure 3-14: Inserting the PCIe Mini Card into the Slot at an Angle
Step 5: Secure the PCIe Mini card. Secure the PCIe Mini card with the retention
screws previously removed (
Figure 3-15). Step 0:
Page 31
Page 45
Figure 3-15: Securing the PCIe Mini Card
PPC-FxxA-H81 Panel PC
3.8 iRIS-2400 Module Installation
WARNING:
The iRIS-2400 module slot is designed to install the iRIS-2400 module
only. DO NOT install other modules into the iRIS-2400 module slot.
Doing so may cause damage to the PPC-FxxA-H81.
To install the iRIS-2400 module, please follow the steps below.
Step 1: Remove the back cover. See Section
Step 2: Remove the HDD bracket to expose the iRIS-2400 module slot
(PPC-F15A/F17A-H81 only). Refer to Step 2 in Section
bracket.
The location of the iRIS-2400 module slot is shown in
63.5.
3.6 to remove the HDD
Figure 3-16.
Page 32
Page 46
PPC-FxxA-H81 Panel PC
Figure 3-16: iRIS-2400 Module Slot
Step 3: Align the iRIS-2400 module with the iRIS-2400 module slot. Align the notch
on the module with the notch on the iRIS-2400 module slot (
Figure 3-17).
Figure 3-17: iRIS-2400 Module Installation
Step 4: Insert the iRIS-2400 module. Push the module in at a 20º angle (
Figure 3-17).
Page 33
Page 47
Step 5: Seat the iRIS-2400 module. Gently push downwards and the arms clip into
PPC-FxxA-H81 Panel PC
place (
Figure 3-17).Step 0:
NOTE:
After installing the iRIS-2400 module, use the LAN port with iRIS label
(
Figure 1-4) to establish a network connection. Please refer to
Section
3.12 for IPMI setup procedures.
3.9 AT/ATX Mode Selection
AT and ATX power modes can both be used on the PPC-FxxA-H81 panel PC. The
selection is made through an AT/ATX switch on the I/O interface panel. The switch is
shown below.
Figure 3-18: AT/ATX Mode Selection
3.10 Mounting the System
WARNING!
When mounting the PPC-FxxA-H81 panel PC, it is advisable to have
more than one person help with the installation to prevent accidental
damage to the panel and avoid personal injury.
Page 34
Page 48
PPC-FxxA-H81 Panel PC
The methods of mounting the PPC-FxxA-H81 are:
Wall mounting
Panel mounting
Arm mounting
Stand mounting
Rack mounting
The mounting methods are described in the following sections.
3.10.1 Wall Mounting
To mount the PPC-FxxA-H81 panel PC onto a wall, please follow the steps below.
Step 1: Select the location on the wall for the wall-mounting bracket.
Step 2: Carefully mark the locations of the four bracket screw holes on the wall.
Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention
screws.
Step 4: Align the wall-mounting bracket screw holes with the pilot holes.
Step 5: Secure the mounting bracket to the wall by inserting the retention screws into
the four pilot holes and tightening them (
Figure 3-19).
Figure 3-19: Wall-mounting Bracket
Page 35
Page 49
Step 6: Insert the four monitor mounting screws provided in the wall mounting kit into the
four screw holes on the real panel of the monitor and tighten until the screw
PPC-FxxA-H81 Panel PC
shank is secured against the rear panel (
Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on
the bracket.
Step 8: Carefully insert the screws through the holes and gently pull the monitor
downwards until the monitor rests securely in the slotted holes (
Ensure that all four of the mounting screws fit snuggly into their respective
slotted holes.
Figure 3-20).
Figure 3-20).
NOTE:
In the diagram below the bracket is already installed on the wall.
Page 36
Figure 3-20: Mount the Chassis
Page 50
PPC-FxxA-H81 Panel PC
Step 9: Secure the panel PC with the wall-mounting kit. To do this, stick the protective
cushion to the wall-mounting kit first. Then, put the wall-mounting kit on the top
panel of the panel PC. Carefully mark the location of the wall-mounting kit screw
holes on the wall. Drill a pilot hole at the marked location on the wall. Secure the
wall-mounting kit to the wall by inserting a retention screw into the pilot hole on
the wall (
from the wall-mounting bracket accidentally. Step 0:
6Figure 3-21). This step is to avoid the panel PC being pushed apart
Figure 3-21: Secure the Chassis
3.10.2 Panel Mounting
To mount the PPC-FxxA-H81 panel PC into a panel, please follow the steps below.
Step 1: Install the mounting brackets onto the rear panel (
number of mounting brackets may vary by models.
Figure 3-22). The required
Page 37
Page 51
Figure 3-22: PPC-F15A-H81 Mounting Bracket Installation
Step 2: Select the position on the panel to mount the PPC-FxxA-H81.
PPC-FxxA-H81 Panel PC
Step 3: Cut out a section of the panel that corresponds to the rear panel dimensions of
the PPC-FxxA-H81. The recommended cutout sizes are shown below
6Figure 3-23, 6Figure 3-24, Figure 3-25 and 6Figure 3-26).
(
Figure 3-23: PPC-F15A-H81 Panel Cutout Dimensions
Page 38
Page 52
PPC-FxxA-H81 Panel PC
Figure 3-24: PPC-F17A-H81 Panel Cutout Dimensions
Figure 3-25: PPC-F22A-H81 Panel Cutout Dimensions
Page 39
Page 53
PPC-FxxA-H81 Panel PC
Figure 3-26: PPC-F24A-H81 Panel Cutout Dimensions
Step 4: Slide the PPC-FxxA-H81 through the hole until the aluminum frame is flush
against the panel.
Step 5: Insert the mounting clamps into the mounting brackets and pre-formed holes
along the edges of the PPC-FxxA-H81, behind the aluminum frame
Figure 3-27). The required number of mounting clamps may vary by models.
(
Step 6: Tighten the screws that pass through the mounting clamps until the plastic caps
at the front of all the screws are firmly secured to the panel (
Step 0:
6Figure 3-27).
Page 40
Page 54
PPC-FxxA-H81 Panel PC
Figure 3-27: Tighten the Mounting Clamp Screws
3.10.3 Rack and Cabinet Installation
The PPC-FxxA-H81 flat panel PC can be installed into a cabinet or rack. The installation
procedures are similar to the panel mounting installation. To do this, please follow the
steps below:
NOTE:
When purchasing the cabinet/rack installation bracket, make sure it is
compatible with both the PPC-FxxA-H81 flat panel PC and the
rack/cabinet into which the PPC-FxxA-H81 is installed.
Page 41
Page 55
Step 1: Install the mounting brackets onto the rear panel (Figure 3-22). The required
number of mounting brackets may vary by models.
Step 2: Slide the rear of the PPC-FxxA-H81 flat panel PC through the rack/cabinet
bracket until the aluminum frame is flush against the front of the bracket
Figure 3-28).
(
PPC-FxxA-H81 Panel PC
Figure 3-28: The Rack/Cabinet Bracket
Step 3: Insert the mounting clamps into the mounting brackets and pre-formed holes
along the edges of the PPC-FxxA-H81, behind the aluminum frame
Figure 3-29). The required number of mounting clamps may vary by models.
(
Step 4: Tighten the screws that pass through the mounting clamps until the plastic caps
at the front of all the screws are firmly secured to the bracket (
Figure 3-29).
Page 42
Page 56
PPC-FxxA-H81 Panel PC
Figure 3-29: Secure the Rack/Cabinet Bracket
Step 5: Slide the PPC-FxxA-H81 with the attached rack/cabinet bracket into a rack or
cabinet (
Figure 3-30).
Page 43
Page 57
Figure 3-30: Install into a Rack/Cabinet
PPC-FxxA-H81 Panel PC
Step 6: Once the flat panel PC with the attached rack/cabinet bracket has been properly
inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to
the front of the rack or cabinet (
Figure 3-30).Step 0:
3.10.4 Arm Mounting
The PPC-FxxA-H81 is VESA (Video Electronics Standards Association) compliant and
can be mounted on an arm with a 100 mm interface pad. To mount the PPC-FxxA-H81 on
an arm, please follow the steps below.
Step 1: The arm is a separately purchased item. Please correctly mount the arm onto
the surface it uses as a base. To do this, refer to the installation documentation
that came with the mounting arm.
NOTE:
Page 44
When purchasing the arm please ensure that it is VESA compliant and
that the arm has a 100 mm interface pad. If the mounting arm is not VESA
compliant, it cannot be used to support the PPC-FxxA-H81 panel PC.
Page 58
PPC-FxxA-H81 Panel PC
Step 2: Once the mounting arm has been firmly attached to its surface, lift the
PPC-FxxA-H81 panel PC onto the interface pad of the mounting arm.
Step 3: Align the retention screw holes on the mounting arm interface with those in the
PPC-FxxA-H81 panel PC. The arm mounting retention screw holes of the
PPC-FxxA-H81 panel PC are shown in
Figure 3-31: Arm Mounting Retention Screw Holes
Figure 3-31.
Step 4: Secure the PPC-FxxA-H81 to the interface pad by inserting four retention
screws through the mounting arm interface pad and into the PPC-FxxA-H81
panel PC.
3.10.5 Stand Mounting
To mount the PPC-FxxA-H81 using the stand mounting kit, please follow the steps below.
Step 1: Locate the screw holes on the rear of the PPC-FxxA-H81. This is where the
bracket will be attached.
Step 0:
Page 45
Page 59
Figure 3-32: Stand Mounting Retention Screw Holes
PPC-FxxA-H81 Panel PC
Step 2: Align the bracket with the screw holes.
Step 3: To secure the bracket to the PPC-FxxA-H81, insert the retention screws into the
screw holes and tighten them.Step 0:
3.11 External Peripheral Device Connection
The following external peripheral devices can be connected to the external peripheral
interface connectors on the bottom panel.
Audio devices
RJ-45 Ethernet cable connector
Serial devices
VGA or HDMI display device
USB devices
To install these devices, connect the corresponding cable connector from the actual
device to the corresponding PPC-FxxA-H81 external peripheral interface connector
making sure the pins are properly aligned.
3.11.1 Audio Device Connection
The audio jacks on the external audio connector enable the PPC-FxxA-H81 to be connected
to the speaker or microphone. To install the audio devices, follow the steps below.
Page 46
Page 60
PPC-FxxA-H81 Panel PC
Step 1: Identify the audio plugs. The plugs on your home theater system or speakers
may not match the colors on the rear panel. If audio plugs are plugged into the
wrong jacks, sound quality will be very bad.
Step 2: Plug the audio plugs into the audio jacks. Plug the audio plugs into the audio
jacks. If the plugs on your speakers are different, an adapter will need to be used
to plug them into the audio jacks. Step 0:
Line Out port (Lime): Connects to a headphone or a speaker.
Microphone (Pink): Connects to a microphone.
Figure 3-33: Audio Connector
NOTE:
If there is no audio device connected to the line-out port, the volume
icon on the Windows notification area displays
When the line-out port is connected with an audio device, the volume
icon will be displayed , allowing the user to adjust the volume and
open a file with audio.
.
Page 47
Page 61
3.11.2 HDMI Display Device Connection
The HDMI connector transmits a digital signal to compatible HDMI display devices such
as a TV or computer screen. To connect the HDMI cable to the PPC-FxxA-H81, follow the
steps below.
PPC-FxxA-H81 Panel PC
Step 1: Locate the HDMI connector. The location is shown in
Step 2: Align the connector. Align the HDMI connector with the HDMI port. Make sure
the orientation of the connector is correct.
Figure 1-4.
Page 48
Figure 3-34: HDMI Connection
Step 3: Insert the HDMI connector. Gently insert the HDMI connector. The connector
should engage with a gentle push. If the connector does not insert easily, check
again that the connector is aligned correctly, and that the connector is being
inserted with the right way up. Step 0:
Page 62
PPC-FxxA-H81 Panel PC
3.11.3 LAN Connection
The RJ-45 LAN connectors allow connections to external networks. To connect the
PPC-FxxA-H81 to a network through the RJ-45 LAN connectors, follow the steps below.
Step 1: Locate the RJ-45 connectors. The locations of the RJ-45 connectors are
shown in
6Figure 1-4.
Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of
the RJ-45 connectors on the PPC-FxxA-H81. See
6Figure 3-35.
Figure 3-35: LAN Connection
Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN
cable RJ-45 connector into the on-board RJ-45 connector.
3.11.4 Serial Device Connection
Follow the steps below to connect a serial device to the DB-9 connector of the
PPC-FxxA-H81.
Step 1: Locate the DB-9 connector. The locations of the DB-9 connectors are shown
7Figure 1-4.
in
Page 49
Page 63
Step 2: Insert the serial connector. Insert the DB-9 connector of a serial device into
PPC-FxxA-H81 Panel PC
the DB-9 connector on the bottom panel. See
Figure 3-36: RS-232 Serial Device Connector
Figure 3-36.
Step 3: Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the connector.
3.11.5 USB Device Connection
To connect a USB device, please follow the instructions below.
Step 1: Located the USB connectors. The locations of the USB connectors are shown
in
Figure 1-4.
Step 2: Align the connectors. Align the USB device connector with one of the USB
connectors on the bottom panel. See
Figure 3-37.
Page 50
Page 64
PPC-FxxA-H81 Panel PC
Figure 3-37: USB Device Connection
Step 3: Insert the device connector. Once aligned, gently insert the USB device
connector into the onboard connector.
3.11.6 VGA Connector Connection
The VGA connector connects to a monitor that accepts VGA video input. To connect the
PPC-FxxA-H81 to a VGA monitor, follow the steps below,
Step 1: Locate the female DB-15 connector. The location of the female DB-15
connector is shown in
Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen
cable with the female DB-15 connector on the external peripheral interface.
Step 3: Insert the VGA connector. Once the connectors are properly aligned, insert the
male connector from the VGA screen into the female connector on the
7Figure 1-4.
PPC-FxxA-H81. See
7Figure 3-38.
Page 51
Page 65
PPC-FxxA-H81 Panel PC
Figure 3-38: VGA Connector
3.12 Reset the System
The reset button enables users to reboot the system when the system is turned on. The
reset button location is shown in
Figure 3-39: Reset Button Location
Figure 3-39. Press the reset button to reboot the system.
Page 52
Page 66
PPC-FxxA-H81 Panel PC
3.13 Clear CMOS
If the PPC-FxxA-H81 fails to boot due to improper BIOS settings, the clear CMOS button
clears the CMOS data and resets the system BIOS information. To do this, push the clear
CMOS button for three seconds, and then restart the system. The clear CMOS button
location is shown in
Figure 3-40.
Figure 3-40: Clear CMOS Button Location
3.14 USB Power Selection
The PPC-FxxA-H81 can select the USB power through the BIOS menu (Chipset Æ
PCH-IO Configuration). Use the USB SW1 Power and the USB SW2 Power BIOS
options to configure the correspondent USB ports (see
to select the USB power source.
Table 3-1) and refer to Table 3-2
BIOS Options Configured USB Ports
KBMS1 (internal keyboard and mouse port)
USB SW1 Power
USB SW2 Power
LAN1_USB1 (external USB 3.0 ports)
LAN2_USB2 (external USB 2.0 ports)
USB1 (internal USB 2.0 ports)
USB_CON1 (external USB 2.0 ports)
Table 3-1: BIOS Options and Configured USB Ports
Options Description
+5V DUAL +5V dual (default)
+5V +5V
Table 3-2: USB Power Source Setup
Please refer to Section 5.4.1 for detailed information.
Page 53
Page 67
3.15 IPMI Setup Procedure
The PPC-FxxA-H81 features Intelligent Platform Management Interface (IPMI) that helps
lower the overall costs of server management by enabling users to maximize IT resources,
save time and manage multiple systems. The PPC-FxxA-H81 supports IPMI 2.0 through
the optional iRIS-2400 module. Follow the steps below to setup IPMI.
3.15.1 Managed System Hardware Setup
The hardware configuration of the managed system (PPC-FxxA-H81) is described below.
PPC-FxxA-H81 Panel PC
Step 1: Install an iRIS-2400 module to the iRIS-2400 module slot (refer to Section
Step 2: Make sure at least one DDR3 DIMM is installed in one of the DIMM sockets. If
multiple DIMMs are installed, all of the DIMMs must be same size, same speed
and same brand to get the best performance.
Step 3: Connect an Ethernet cable to the RJ-45 LAN port with iRIS label (
Figure 1-4).
3.15.2 Using the IEI iMAN Web GUI
To manage a client system from a remote console using IEI iMAN Web GUI, follow the
steps below.
Step 1: Obtain the IP address of the managed system. It is recommended to use the
IPMI Tool on the managed system to obtain the IP address. To use IPMI Tool to
obtain IP address, follow the steps below:
a. Copy the Ipmitool.exe file to a bootable USB flash drive.
3.8).
Page 54
b. Insert the USB flash drive to the PPC-FxxA-H81
c. The PPC-FxxA-H81 boots from the USB flash drive
d. Enter the following command: ipmitool 20 30 02 01 03 00 00
(there is a space between each two-digit number)
e. A serial of number shows. The last four two-digit hexadecimal numbers are
the IP address. Convert the hexadecimal numbers to decimal numbers.
Page 68
PPC-FxxA-H81 Panel PC
Step 2: On the remote management console, open a web browser. Enter the managed
system IP address in the web browser (
Figure 3-41: IEI iMAN Web Address
Step 3: The login page appears in the web browser.
Step 4: Enter the user name and password to login the system. The default login
username and password are:
-Username: admin
-Password: admin
Step 5: Press the login button to login the system.
Step 6: The IEI iMAN Web Interface appears. Step 0:
Figure 3-41).
Figure 3-42: IEI iMAN Web GUI
NOTE:
To understand how to use the IEI iMAN Web GUI, please refer to the
iRIS-2400 Web GUI user manual in the utility CD came with the
PPC-FxxA-H81. The user manual describes each function in detail.
Page 55
Page 69
PPC-FxxA-H81 Panel PC
Chapter
4
4 System Maintenance
Page 56
Page 70
PPC-FxxA-H81 Panel PC
4.1 System Maintenance Introduction
The following system components may require maintenance.
Motherboard
Memory module
Cooling fans
If these components fail, they must be replaced. Please contact the system reseller or
vendor to purchase replacement parts. Replacement instructions for the above listed
components are described below.
4.2 Motherboard Replacement
A user cannot replace a motherboard. If the motherboard fails it must be shipped back to
IEI to be replaced. If the system motherboard has failed, please contact the system vendor,
reseller or an IEI sales person directly.
4.3 Back Cover Removal
WARNING!
Before removing the back cover, make sure all power to the system
has been disconnected. Failing to do so may cause severe damage to
the PPC-FxxA-H81 and injury to the user.
WARNING!
Please take antistatic precautions when working with the internal
components. The interior of the PPC-FxxA-H81 contains very sensitive
electronic components. These components are easily damaged by
electrostatic discharge (ESD). Before working with the internal
components, make sure all anti-static precautions described earlier
have been observed.
Page 57
Page 71
PPC-FxxA-H81 Panel PC
To access the panel PC internal components, the back cover must be removed. To
remove the back cover, please refer to Section
4.4 SO-DIMM Replacement
Please read the warnings at the beginning of the previous section before attempting to
access any PPC-FxxA-H81 internal components.
To install/replace the SO-DIMM modules, please follow the steps below.
Step 1: Remove the back cover (Section
Step 2: Locate the SO-DIMM module on the motherboard.
73.5 for back cover removal instructions.
73.5).
Page 58
Figure 4-1: SO-DIMM Module Locations
Step 3: Push the two handles outwards (
Figure 4-2). The memory module is ejected by
a mechanism in the socket.
Step 4: Grasp the SO-DIMM module by the edges and carefully pull it out of the socket.
Step 5: Align the new SO-DIMM so the notch on the memory lines up with the notch on
the memory socket (
Figure 4-2).
Page 72
PPC-FxxA-H81 Panel PC
Step 6: Once aligned, press down until the SO-DIMM is properly seated. Clip the two
handles into place.
Figure 4-2: SO-DIMM Module Installation
Step 0:
4.5 System Cooling Fan Replacement
If the system cooling fans have been damaged, they must be replaced. To replace the
system cooling fans, please follow the steps below.
4.5.1 Remove the Old System Cooling Fans
Step 1: Remove the back cover (Section 73.5).
Page 59
Page 73
Step 2: Disconnect the system cooling fans from the motherboard (7Figure 4-3).
PPC-FxxA-H81 Panel PC
Figure 4-3: System Cooling Fans Motherboard Connectors
Step 3: Remove the system cooling fan retention screws from the left panel
(
7Figure 4-4).
Figure 4-4: System Cooling Fan Retention Screws
Step 4: Remove the system cooling fans from the chassis. Step 0:
4.5.2 Install the New System Cooling Fans
To install the new system cooling fans, please follow the steps below.
Page 60
Step 1: Insert the system cooling fans into the chassis and attach to the left panel with
the previously removed retention screws.
Page 74
PPC-FxxA-H81 Panel PC
Step 2: Rebundle the new fan wires and tie them to the chassis like the old fan wires.
Step 3: Reconnect the new fan connector to the motherboard.
Step 4: Replace the back cover.Step 0:
Page 61
Page 75
PPC-FxxA-H81 Panel PC
Chapter
5
5 BIOS Setup
Page 62
Page 76
PPC-FxxA-H81 Panel PC
5.1 Introduction
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
NOTE:
Some of the BIOS options may vary throughout the life cycle of the
product and are subject to change without prior notice.
5.1.1 Starting Setup
The UEFI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the D
2. Press the D
message appears on the screen. 0.
If the message disappears before the D
and try again.
ELETE or F2 key as soon as the system is turned on or
ELETE or F2 key when the “Press DELETE or F2 to enter SETUP”
ELETE or F2 key is pressed, restart the computer
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press E
keys are shown in the following table.
Key Function
Up arrow Move to the item above
Down arrow Move to the item below
Left arrow Move to the item on the left hand side
SC to quit. Navigation
Right arrow Move to the item on the right hand side
+ Increase the numeric value or make changes
Page 63
Page 77
Key Function
- Decrease the numeric value or make changes
Page up Move to the next page
Page down Move to the previous page
Esc Main Menu – Quit and do not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu --
Exit current page and return to Main Menu
F1 General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 Load previous values
F3 Load optimized defaults
F4 Save changes and Exit BIOS
PPC-FxxA-H81 Panel PC
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press E
the F1 key again.
5.1.4 Unable to Reboot after Configuration Changes
If the computer cannot boot after changes to the system configuration are made, press the
Clear CMOS button on the bottom panel to clear the CMOS data and reset the system
BIOS information. The location of the CMOS button is shown in
7Figure 1-4.
5.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main – Changes the basic system configuration.
SC or
Page 64
Advanced – Changes the advanced system settings.
Chipset – Changes the chipset settings.
Boot – Changes the system boot configuration.
Page 78
PPC-FxxA-H81 Panel PC
Security – Sets User and Supervisor Passwords.
Save & Exit – Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
Page 65
Page 79
PPC-FxxA-H81 Panel PC
5.2 Main
The Main BIOS menu (7BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
BIOS Information
BIOS Vendor American Megatrends
Core Version 4.6.5.4
Compliancy UEFI 2.3.1; PI 1.2
Project Version H773AR10.ROM
Build Date and Time 07/28/2014 11:53:40
iWDD Vendor iEi
iWDD Version H773ER18.bin
IPMI Module N/A
Processor Information
Name Haswell
Brand String Intel(R) Core(TM) i5-457
Frequency 3200 MHz
Processor ID 306c3
Stepping C0
Number of Processors 4Core(s) / 4Thread(s)
Microcode Revision 16
GT Info GT2 (700 MHz)
IGFX VBIOS Version 2178
Memory RC Version 1.6.2.1
Total Memory 4096 MB (DDR3)
Memory Frequency 1333 MHz
PCH Information
Name LynxPoint
PCH SKU H81
Stepping 05/C2
LAN PHY Revision N/A
ME FW Version 9.1.10.1005
ME Firmware SKU 1.5MB
SPI Clock Frequency
DOFR Support Supported
Read Status Clock Frequnecy 50 MHz
Write Status Clock Frequnecy 50 MHz
Fast Read Status Clock Frequnecy 50 MHz
System Date [Fri 08/08/2014]
System Time [15:10:27]
Access Level Administrator
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Set the Date. Use Tab to
switch between Data
elements.
----------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Page 66
BIOS Menu 1: Main
Page 80
PPC-FxxA-H81 Panel PC
The Main menu has two user configurable fields:
Î System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
Î System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
5.3 Advanced
Use the Advanced menu (7BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING!
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
Page 67
Page 81
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
> ACPI Settings
> RTC Wake Settings
> CPU Configuration
> SATA Configuration
> USB Configuration
> F81866 Super IO Configuration
> iWDD H/M Monitor
> Serial Port Console Redirection
> iEi Feature
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
BIOS Menu 2: Advanced
PPC-FxxA-H81 Panel PC
System ACPI Parameters
----------------------
ÆÅ
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
: Select Screen
5.3.1 ACPI Settings
The ACPI Settings menu (7BIOS Menu 3) configures the Advanced Configuration and
Power Interface (ACPI) options.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
ACPI Settings
ACPI Sleep State [S1 only(CPU Stop C1...]
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Select the ACPI sleep state
the system will enter when
the SUSPEND button is
pressed.
----------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Page 68
BIOS Menu 3: ACPI Settings
Page 82
E
w
PPC-FxxA-H81 Panel PC
Î ACPI Sleep State [S1 only (CPU Stop Clock)]
Use the ACPI Sleep State option to specify the sleep state the system enters when it is
not being used.
Î
S1 only (CPU Stop
Clock)
Î
S3 only (Suspend
to RAM)
DEFAULT
The system enters S1(POS) sleep state. The
system appears off. The CPU is stopped; RAM is
refreshed; the system is running in a low power
mode.
The caches are flushed and the CPU is powered
off. Power to the RAM is maintained. The
computer returns slower to a working state, but
more power is saved.
5.3.2 RTC Wake Settings
The RTC Wake Settings menu (BIOS Menu 4) enables the system to wake at the
specified time.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
Wake system with Fixed Time [Disabled]
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
nable or disable System
ake on alarm event. When
enabled, System will
wake on the
date::hr::min::sec
specified
----------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 4: RTC Wake Settings
Page 69
Page 83
Î Wake system with Fixed Time [Disab led]
Use the Wake system with Fixed Time option to enable or disable the system wake on
alarm event.
PPC-FxxA-H81 Panel PC
Î
Disabled D
Î
Enabled
EFAULT
The real time clock (RTC) cannot generate a wake
event
If selected, the Wake up every day option appears
allowing you to enable to disable the system to wake
every day at the specified time. Besides, the
following options appear with values that can be
selected:
Wake up date
Wake up hour
Wake up minute
Wake up second
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
Page 70
Page 84
N
PPC-FxxA-H81 Panel PC
5.3.3 CPU Configuration
Use the CPU Configuration menu (7BIOS Menu 5) to view detailed CPU specifications
and configure the CPU.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
CPU Configuration
Intel(R) Core(TM) i5-4570S CPU @ 2.90GHz
CPU Signature 306c3
Processor Samily 6
Microcode Patch 16
FSB Speed 100 MHz
Max CPU Speed 2900 MHz
Min CPU Speed 800 MHz
CPU Speed 3200 MHz
Processor Cores 4
Intel HT Technology Supported
Intel VT-x Technology Supported
Intel SMX Technology Supported
64-bit Supported
CPU C3 state Supported
CPU C6 state Supported
CPU C7 state Supported
L1 Data Cache 32 KB x 4
L1 Code Cache 32 KB x 4
L2 Cache 256 KB x 4
L3 Cache 6144 KB
Active Processor Cores [All]
Intel Virtualization Technology [Disabled]
EIST [Enabled]
Intel TXT(LT) Support [Disabled]
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
umber of cores to enable
in each processor package.
----------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 5: CPU Configuration
The CPU Configuration menu (
CPU Signature: Lists the CPU signature value.
Processor Family: Lists the processor family.
Microcode Patch: Lists the microcode patch being used.
FSB Speed: Lists the FSB speed.
Max CPU Speed: Lists the maximum CPU processing speed.
Min CPU Speed: Lists the minimum CPU processing speed.
7BIOS Menu 5) lists the following CPU details:
Page 71
Page 85
CPU Speed: Lists the CPU processing speed.
Processor Cores: Lists the number of the processor core
Intel HT Technology: Indicates if Intel HT Technology is supported by the CPU.
Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the
CPU.
Intel SMX Technology: Indicates if Intel SMX Technology is supported by the
CPU.
64-bit: Indicates if 64-bit system is supported by the CPU.
EIST Technology: Indicates if EIST Technology is supported by the CPU.
CPU C3 state: Indicates if CPU C3 state is supported by the CPU.
CPU C6 state: Indicates if CPU C6 state is supported by the CPU.
CPU C7 state: Indicates if CPU C7 state is supported by the CPU.
L1 Data Cache: Lists the amount of data storage space on the L1 cache.
L1 Code Cache: Lists the amount of code storage space on the L1 cache.
PPC-FxxA-H81 Panel PC
L2 Cache: Lists the amount of storage space on the L2 cache.
L3 Cache: Lists the amount of storage space on the L3 cache.
Î Active Processor Cores [All]
Use the Active Processor Cores BIOS option to enable numbers of cores in the
processor package.
Î
All DEFAULT
Î
1
Î
2
Î
3
Î Intel Virtualization Technology [Disabled]
Use the Intel Virtualization Technology option to enable or disable virtualization on the
system. When combined with third party software, Intel® Virtualization technology allows
Enable all cores in the processor package.
Enable one core in the processor package.
Enable two cores in the processor package.
Enable three cores in the processor package.
Page 72
several OSs to run on the same system at the same time.
Î
Disabled DEFAULT
Î
Enabled
Disables Intel Virtualization Technology.
Enables Intel Virtualization Technology.
Page 86
PPC-FxxA-H81 Panel PC
Î EIST [Enabled]
Use the EIST option to enable or disable the Enhanced Intel® SpeedStep Technology (EIST).
Î
Disabled
Î
Enabled DEFAULT
Disables Enhanced Intel® SpeedStep Technology
Enables Enhanced Intel® SpeedStep Technology
5.3.4 SATA Configuration
Use the SATA Configuration menu (7BIOS Menu 6) to change and/or set the
configuration of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
SATA Controller(s) [Enabled]
SATA Mode Selection [IDE]
SATA1 Port Empty
SATA2 Port Empty
mSATA Port Empty
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Enable or disable SATA
Device.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 6: SATA Configuration
Î SATA Controller(s) [Enabl ed]
Use the SATA Controller(s) option to configure the SATA controller(s).
Î
Enabled DEFAULT
Î
Disabled
Enables the on-board SATA controller(s).
Disables the on-board SATA controller(s).
Page 73
Page 87
d
Î SATA Mode Selection [IDE]
Use the SATA Mode Selection option to determine how SATA devices operate.
PPC-FxxA-H81 Panel PC
Î
IDE DEFAULT
Î
AHCI
Configures SATA devices as AHCI device.
Configures SATA devices as normal IDE device.
5.3.5 USB Configuration
Use the USB Configuration menu (7BIOS Menu 7) to read USB configuration information
and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices:
1 Keyboard, 2 Hubs
Legacy USB Support [Enabled]
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Enables Legacy USB
support. AUTO option
isables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 7: USB Configuration
Î USB Devices
The USB Devices field lists the USB devices that are enabled on the system
Î Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
Page 74
Page 88
PPC-FxxA-H81 Panel PC
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.
Î
Enabled DEFAULT
Î
Disabled
Î
Auto
Legacy USB support enabled
Legacy USB support disabled
Legacy USB support disabled if no USB devices are
connected
5.3.6 F81866 Super IO Configuration
Use the F81866 Super IO Configuration menu (7BIOS Menu 8) to set or change the
configurations for the serial ports.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
F81866 Super IO Configuration
F81866 Super IO Chip F81866
> Serial Port 1 Configuration
> Serial Port 2 Configuration
> Serial Port 3 Configuration
> Serial Port 4 Configuration
> Serial Port 5 Configuration
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Set Parameters of Serial
Port 1 (COMA)
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 8: F81866 Super IO Configuration
Page 75
Page 89
PPC-FxxA-H81 Panel PC
5.3.6.1 Serial Port n Configuration
Use the Serial Port n Configuration menu (7BIOS Menu 9) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
Serial Port n Configuration
Serial Port [Enabled]
Device Settings IO=3F8h; IRQ=4
Change Settings [Auto]
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Enable or Disable Serial
Port (COM)
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 9: Serial Port n Configuration Menu
5.3.6.1.1 Serial Port 1 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Î
Enabled DEFAULT
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto DEFAULT
Disable the serial port
Enable the serial port
The serial port IO port address and interrupt address
are automatically detected.
Page 76
Î
IO=3F8h;
IRQ=4
Serial Port I/O port address is 3F8h and the interrupt
address is IRQ4
Page 90
PPC-FxxA-H81 Panel PC
Î
IO=3F8h;
IRQ=3, 4
Î
IO=2C0h;
IRQ=3, 4
Î
IO=2C8h;
IRQ=3, 4
5.3.6.1.2 Serial Port 2 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Î
Enabled DEFAULT
Serial Port I/O port address is 3F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2C0h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2C8h and the interrupt
address is IRQ3, 4
Disable the serial port
Enable the serial port
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto DEFAULT
Î
IO=2F8h;
IRQ=3
Î
IO=3F8h;
IRQ=3, 4
Î
IO=2F8h;
IRQ=3, 4
Î
IO=2C0h;
IRQ=3, 4
Î
IO=2C8h;
The serial port IO port address and interrupt address
are automatically detected.
Serial Port I/O port address is 2F8h and the interrupt
address is IRQ3
Serial Port I/O port address is 3F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2C0h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2C8h and the interrupt
IRQ=3, 4
address is IRQ3, 4
Page 77
Page 91
5.3.6.1.3 Serial Port 3 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
PPC-FxxA-H81 Panel PC
Î
Disabled
Î
Enabled DEFAULT
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto DEFAULT
Î
Î
Î
IO=2D0h;
IRQ=10
IO=2D0h;
IRQ=10, 11
IO=2E8h;
IRQ=10, 11
Disable the serial port
Enable the serial port
The serial port IO port address and interrupt address
are automatically detected.
Serial Port I/O port address is 2D0h and the interrupt
address is IRQ10
Serial Port I/O port address is 2D0h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2E8h and the interrupt
address is IRQ10, 11
Î
IO=2D8h;
IRQ=10, 11
5.3.6.1.4 Serial Port 4 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Î
Enabled DEFAULT
Page 78
Serial Port I/O port address is 2D8h and the interrupt
address is IRQ10, 11
Disable the serial port
Enable the serial port
Page 92
PPC-FxxA-H81 Panel PC
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto DEFAULT
Î
IO=2E8h;
IRQ=10
Î
IO=3E8h;
IRQ=10, 11
Î
IO=2E8h;
IRQ=10, 11
Î
IO=2D0h;
IRQ=10, 11
Î
IO=2D8h;
IRQ=10, 11
The serial port IO port address and interrupt address
are automatically detected.
Serial Port I/O port address is 2E8h and the interrupt
address is IRQ10
Serial Port I/O port address is 3E8h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2E8h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2D0h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2D8h and the interrupt
address is IRQ10, 11
5.3.6.1.5 Serial Port 5 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Î
Enabled DEFAULT
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Disable the serial port
Enable the serial port
Page 79
Page 93
PPC-FxxA-H81 Panel PC
Î
Auto DEFAULT
Î
IO=2D0h;
IRQ=10
Î
IO=2C0h;
IRQ=10, 11
Î
IO=2C8h;
IRQ=10, 11
Î
IO=2D0h;
IRQ=10, 11
Î
IO=2D8h;
IRQ=10, 11
Î
IO=2E0h;
IRQ=10, 11
The serial port IO port address and interrupt address
are automatically detected.
Serial Port I/O port address is 2D0h and the interrupt
address is IRQ10
Serial Port I/O port address is 2C0h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2C8h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2D0h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2D8h and the interrupt
address is IRQ10, 11
Serial Port I/O port address is 2E0h and the interrupt
address is IRQ10, 11
Î Device Mode [Normal]
The Device Mode option is used to set the Serial Port 5 signaling mode.
Î
RS422/
RS485
5.3.7 iWDD H/W Monitor
The iWDD H/W Monitor menu (7BIOS Menu 10) displays operating temperature and fan
speeds.
Enables serial port RS-422/485 support.
Page 80
Page 94
PPC-FxxA-H81 Panel PC
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
PC Health Status
> Smart Fan Mode Configuration
CPU temperature : +53 C
System temperature : +45 C
CPU_FAN1 Speed : 1908 RPM
SYS_FAN1 Speed : 160 RPM
SYS_FAN2 Speed : 160 RPM
CPU_CORE : +1.415 V
+5V : +5.090 V
+12V : +12.026 V
DDR : +1.508 V
+3.3VSB : +3.311 V
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
BIOS Menu 10: F81866 H/W Monitor
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Î PC Health Status
The following system parameters and values are shown. The system parameters that are
monitored are:
System Temperatures:
o CPU Temperature
o System Temperature
Fan Speeds:
o CPU_Fan1 Speed
o SYS_Fan1 Speed
o SYS_Fan2 Speed
Voltages:
o CPU_CORE
o +5V
o +12V
o DDR
o +3.3VSB
o VBAT
Page 81
Page 95
PPC-FxxA-H81 Panel PC
5.3.8 Serial Port Console Redirection
The Serial Port Console Redirection menu (7BIOS Menu 11) allows the console
redirection options to be configured. Console redirection allows users to maintain a
system remotely by re-directing keyboard input and text output through the serial port.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
COM1
Console Redirection [Disabled]
> Console Redirection Settings
COM2
Console Redirection [Disabled]
> Console Redirection Settings
COM3
Console Redirection [Disabled]
> Console Redirection Settings
COM4
Console Redirection [Disabled]
> Console Redirection Settings
COM7 (BMC) (Disabled)
Console Redirection Settings Port Is Disabled
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Console Redirection
Enable or Disable
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 11: Serial Port Console Redirection
Î Console Redirection [Disabled]
Use Console Redirection option to enable or disable the console redirection function.
Î
Disabled DEFAULT
Î
Enabled
5.3.8.1 Console Redirection Settings
Use the Console Redirection Settings menu (7BIOS Menu 12) to configure console
redirection settings of the specified serial port. This menu appears only when the Console
Redirection is enabled.
Page 82
Disabled the console redirection function
Enabled the console redirection function
Page 96
E
c
PPC-FxxA-H81 Panel PC
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
COM1
Console Redirection Settings
Terminal Type [ANSI]
Bits per second [115200]
Data Bits [8]
Parity [None]
Stop Bits [1]
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
mulation: ANSI: Extended
ASCII char set. VT100:
ASCII char set. VT100+:
Extends VT100 to support
olor, function keys, etc.
VT-UTF8: Uses UTF8
encoding to map Unicode
chars onto 1 or more bytes.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 12: Console Redirection Settings
Î Terminal Type [ANSI]
Use the Terminal Type option to specify the remote terminal type.
Î
VT100
Î
VT100+
Î
VT-UTF8
Î
ANSI DEFAULT
Î Bits per second [115200]
Use the Bits per second option to specify the serial port transmission speed. The speed
must match the other side. Long or noisy lines may require lower speeds.
Î
9600
The target terminal type is VT100
The target terminal type is VT100+
The target terminal type is VT-UTF8
The target terminal type is ANSI
Sets the serial port transmission speed at 9600.
Î
19200
Î
57600
Î
115200 DEFAULT
Sets the serial port transmission speed at 19200.
Sets the serial port transmission speed at 57600.
Sets the serial port transmission speed at 115200.
Page 83
Page 97
Î Data Bits [8]
Use the Data Bits option to specify the number of data bits.
PPC-FxxA-H81 Panel PC
Î
7
Î
8 DEFAULT
Î Parity [None]
Use the Parity option to specify the parity bit that can be sent with the data bits for
detecting the transmission errors.
Î
None DEFAULT
Î
Even
Î
Odd
Î
Mark
Î
Space
Sets the data bits at 7.
Sets the data bits at 8.
No parity bit is sent with the data bits.
The parity bit is 0 if the number of ones in the data
bits is even.
The parity bit is 0 if the number of ones in the data
bits is odd.
The parity bit is always 1. This option does not
provide error detection.
The parity bit is always 0. This option does not
Î Stop Bits [1]
Use the Stop Bits option to specify the number of stop bits used to indicate the end of a
serial data packet. Communication with slow devices may require more than 1 stop bit.
Î
Î
Page 84
1 DEFAULT
2
provide error detection.
Sets the number of stop bits at 1.
Sets the number of stop bits at 2.
Page 98
c
s
PPC-FxxA-H81 Panel PC
5.3.9 iEi Feature
Use the iEi Feature menu (BIOS Menu 12) to configure One Key Recovery function.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
iEi Feature
Auto Recovery Function [Disabled]
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Auto Recovery Function
Reboot and recover
system automatically
within 10 min, when OS
rashes. Please install
Auto Recovery API
ervice before enabling
this function.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 13: iEi Feature
Î Auto Recovery Function [Disabled]
Use the Auto Recovery Function BIOS option to enable or disable the auto recovery
function of the IEI One Key Recovery.
Î
Disabled DEFAULT
Î
Enabled
Auto recovery function disabled
Auto recovery function enabled
Page 85
Page 99
PPC-FxxA-H81 Panel PC
5.4 Chipset
Use the Chipset menu (7BIOS Menu 14) to access the PCH and System Agent (SA)
configuration menus.
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
> PCH-IO Configuration
> System Agent (SA) Configuration
PCH Parameters
---------------------
ÆÅ
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
: Select Screen
Page 86
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
BIOS Menu 14: Chipset
Page 100
S
PPC-FxxA-H81 Panel PC
5.4.1 PCH-IO Configuration
Use the PCH-IO Configuration menu (7BIOS Menu 15) to configure the PCH IO settings.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Chipset
Auto Power Button Function [Disabled (ATX)]
Restore AC Power Loss [Last State]
> PCI Express Configuration
> PCH Azalia Configuration
Power Saving Function(ERP) [Disabled]
USB SW1 Power [+5V DUAL]
USB SW2 Power [+5V DUAL]
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
elect AC power state when
power is re-applied after
a power failure.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 15: PCH-IO Configuration
Î Restore AC Power Loss [Last State]
Use the Restore AC Power Loss BIOS option to specify what state the system returns to
if there is a sudden loss of power to the system.
Î
Power Off
Î
Power On
Î
Last State DEFAULT
Î Power Saving Function(ERP) [Disabled]
Use the Power Saving Function(ERP) option to enable or disable the power saving
function.
The system remains turned off
The system turns on
The system returns to its previous state. If it was on, it
turns itself on. If it was off, it remains off.
Î
Disabled DEFAULT
Î
Enabled
Disables the power saving function.
Enables the power saving function.
Page 87
Loading...