IEI Technology POC-W24C-ULT3, POC-W24C-ULT3-i7/PC/4G, POC-W24C-ULT3-i5/PC/4G, POC-W24C-ULT3-C/PC/4G User Manual
Page 1
POC-W24C-ULT3 FHD Medical Panel PC
MODEL:
POC-W24C-ULT3
24” FHD Medical Panel PC with Intel® Core™ i7-6600U/Core™ i5-6300U/
Celeron® 3855U CPU, 4 GB DDR4 RAM, Wi-Fi 802.11a/b/g/n/ac,
PCAP Touchscreen, 5-Megapixel Camera and Microphone
User Manual
User Manual
Rev. 1.01 - November 28, 2017
Page i
Page 2
POC-W24C-ULT3 FHD Medical Panel PC
Revision
Date Version Changes
November 28, 2017 1.01 Added the 150W/19V power adapter as the power supply option
August 22, 2017 1.00 Initial release
Page ii
Page 3
POC-W24C-ULT3 FHD Medical Panel PC
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
Copyright
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
CONTACT INFORMATION
IEI Integration Corp.
Address:
Phone:
Fax:
No. 29, Zongxing Rd., Xizhi Dist.,
New Taipei City 221, Taiwan
+886-2-8691-6798
+886-2-6616-0028
Web Site:
Sales Email:
www.ieiworld.com
sales@ieiworld.com.tw
Page iii
Page 4
POC-W24C-ULT3 FHD Medical Panel PC
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any directions
or instructions contained therein can help avoid making mistakes.
HOT SURFACE
This symbol indicates a hot surface that should not be touched without
taking care.
OPERATING INSTRUCTION
Follow operating instructions or consult instructions for use.
Page iv
Page 5
POC-W24C-ULT3 FHD Medical Panel PC
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 MODEL VARIATIONS................................................................................................... 3
1.3 FEATURES................................................................................................................... 3
1.4 FRONT PANEL............................................................................................................. 4
1.4.1 Backlit Touch Buttons ........................................................................................ 5
1.5 LEFT PANEL................................................................................................................ 6
1.6 BOTTOM PANEL.......................................................................................................... 7
1.7 REAR PANEL............................................................................................................... 8
1.8 SYSTEM SPECIFICATIONS............................................................................................ 8
1.9 DIMENSIONS............................................................................................................. 12
2 UNPACKING............................................................................................................... 13
2.1 UNPACKING.............................................................................................................. 14
2.2 PACKING LIST........................................................................................................... 15
2.3 OPTIONAL ITEMS...................................................................................................... 16
3 INSTALLATION ......................................................................................................... 19
3.1 ANTI-STATIC PRECAUTIONS...................................................................................... 20
3.2 INSTALLATION PRECAUTIONS................................................................................... 20
3.3 INST ALLATION AND CONFIGURATION STEPS ............................................................. 21
3.4 HDD INSTALLATION................................................................................................. 21
3.5 HANDSET INSTALLATION (OPTIONAL) ...................................................................... 23
3.5.1 Using VoIP Handset......................................................................................... 25
3.6 HANDLE INSTALLATION (OPTIONAL)........................................................................ 29
3.6.1 Barcode Reader Installation............................................................................ 29
3.6.2 Reading Light................................................................................................... 31
3.7 3-IN-1 COMBO READER INSTALLATION (OPTIONAL) ................................................ 32
3.8 USING RFID READER (OPTIONAL)........................................................................... 33
3.9 RS-232/422/485 SERIAL PORT CONNECTION........................................................... 36
3.10 AT/ATX MODE SELECTION.................................................................................... 37
Page v
Page 6
3.10.1 AT Power Mode.............................................................................................. 37
3.10.2 ATX Power Mode........................................................................................... 37
3.11 MOUNTING THE SYSTEM ........................................................................................ 37
3.1 1.1 Wall Mounting................................................................................................ 38
3.1 1.2 Arm Mounting ................................................................................................ 41
3.11.3 Stand Mounting.............................................................................................. 43
3.12 POWERING ON THE SYSTEM................................................................................... 43
3.13 RESET THE SYSTEM................................................................................................ 44
4 BIOS SETUP................................................................................................................ 45
4.1 INTRODUCTION......................................................................................................... 46
4.1.1 Starting Setup................................................................................................... 46
4.1.2 Using Setup...................................................................................................... 46
4.1.3 Getting Help..................................................................................................... 47
4.1.4 BIOS Menu Bar................................................................................................ 47
POC-W24C-ULT3 FHD Medical Panel PC
4.2 MAIN........................................................................................................................ 48
4.3 ADVANCED............................................................................................................... 49
4.3.1 T rusted Computing........................................................................................... 50
4.3.2 ACPI Settings................................................................................................... 51
4.3.3 F81866 Super IO Configuration...................................................................... 52
4.3.3.1 Serial Port n Configuration....................................................................... 52
4.3.3.1.1 Serial Port 1 Configuration................................................................ 53
4.3.3.1.2 Serial Port 2 Configuration................................................................ 54
4.3.4 F81866 H/W Monitor....................................................................................... 55
4.3.5 RTC Wake Settings........................................................................................... 56
4.3.6 Serial Port Console Redirection...................................................................... 57
4.3.6.1 Console Redirection Settings.................................................................... 58
4.3.6.2 Legacy Console Redirection Settings....................................................... 60
4.3.7 CPU Configuration.......................................................................................... 61
4.3.8 SATA Configuration ......................................................................................... 63
4.3.9 USB Configuration........................................................................................... 65
4.3.10 IEI Feature..................................................................................................... 66
4.4 CHIPSET ................................................................................................................... 67
4.4.1 System Agent (SA) Configuration .................................................................... 67
4.4.1.1 Graphics Configuration............................................................................. 68
Page vi
Page 7
POC-W24C-ULT3 FHD Medical Panel PC
4.4.1.1.1 LCD Control ...................................................................................... 70
4.4.1.2 Memory Configuration ............................................................................. 71
4.4.2 PCH-IO Configuration .................................................................................... 71
4.4.2.1 PCI Express Configuration....................................................................... 72
4.4.2.2 HD Audio Configuration........................................................................... 73
4.5 SECURITY................................................................................................................. 74
4.6 BOOT........................................................................................................................ 75
4.7 SAVE & EXIT............................................................................................................ 77
5 DRIVER INSTALLATION......................................................................................... 79
5.1 AVAILABLE SOFTWARE DRIVERS .............................................................................. 80
5.2 INTEL® CHIPSET DRIVER......................................................................................... 81
5.3 INTEL® GRAPHICS DRIVER ...................................................................................... 82
5.4 AUDIO DRIVER......................................................................................................... 83
5.5 LAN DRIVER ........................................................................................................... 84
5.6 INTEL® MANAGEMENT ENGINE............................................................................... 85
5.7 WIRELESS LAN DRIVER .......................................................................................... 86
5.8 BLUETOOTH DRIVER................................................................................................ 87
5.9 KEYPAD AP.............................................................................................................. 88
5.10 RFID DRIVER (OPTIONAL)..................................................................................... 89
5.11 3-IN-1 COMBO READER DRIVER (OPTIONAL)......................................................... 92
5.11.1 SCR Driver..................................................................................................... 92
5.11.2 MSR Driver .................................................................................................... 96
5.11.3 Fingerprint Reader Driver............................................................................. 99
5.12 BARCODE READER DRIVER (OPTIONAL).............................................................. 101
6 SYSTEM MAINTENANCE ..................................................................................... 103
6.1 SYSTEM MAINTENANCE INTRODUCTION ................................................................ 104
6.2 ANTI-STATIC PRECAUTIONS.................................................................................... 104
6.3 TURN OFF THE POWER............................................................................................ 105
6.4 REMOVING THE COVERS ........................................................................................ 105
6.5 SO-DIMM REPLACEMENT..................................................................................... 106
6.6 PCIE MINI CARD INSTALLATION ............................................................................ 108
6.7 REINST ALLING THE COVERS................................................................................... 109
7 INTERFACE CONNECTORS..................................................................................110
Page vii
Page 8
7.1 PERIPHERAL INTERFACE CONNECTORS....................................................................111
7.2 INTERNAL PERIPHERAL CONNECTORS .....................................................................112
7.2.1 Audio Connector (AUDIO_OUT1).................................................................113
7.2.2 Audio Out Connector (AMP_OUT1)..............................................................113
7.2.3 Battery Connector (BAT1)..............................................................................113
7.2.4 Debug Connector (DBG_PORT1)..................................................................114
7.2.5 Inverter Connector (INVERTER1)..................................................................114
7.2.6 LVDS Connector (LVDS1)..............................................................................114
7.2.7 MCU Connector (HOTKEY_CN1) .................................................................115
7.2.8 MCU Flash Connector (JP8)..........................................................................116
7.2.9 MCU Flash SPI ROM Connector (MCU_SPI1).............................................116
7.2.10 Microphone Connector (DMIC1).................................................................116
7.2.11 Power Button Connector (PWR_BTN1)........................................................117
7.2.12 Power LED Connector (PW_LED1).............................................................117
POC-W24C-ULT3 FHD Medical Panel PC
7.2.13 RS-232 Serial Port Connector (COM2)........................................................117
7.2.14 SATA Connectors (SATA1 & SATA2) ............................................................118
7.2.15 SPI Flash Connector (JSPI1)........................................................................118
7.2.16 TPM Connector (TPM1)...............................................................................118
7.2.17 USB Connector (BT_USB1)..........................................................................119
7.2.18 USB Connector (CAM_USB1)......................................................................119
7.2.19 USB Connector (RFID_USB1).................................................................... 120
7.2.20 USB Connector (TOUCH_USB1) ................................................................ 120
7.3 EXTERNAL INTERFACE PANEL CONNECTORS.......................................................... 120
7.3.1 GbE Connectors (LAN1 & LAN2) ................................................................. 121
7.3.2 HDMI Output Connector (HDMI_OUT1)..................................................... 121
7.3.3 Power Connector (PWR1) ............................................................................. 122
7.3.4 RS-232/422/485 DB-9 Serial Port (COM1)................................................... 122
7.3.5 USB 2.0 Connectors (USB20_CN1) .............................................................. 122
7.3.6 USB 3.0 Connectors (USB_CON1)................................................................ 123
7.3.7 USB 3.0 Connectors (USB_CON2)................................................................ 123
7.4 PRECONFIGURED JUMPER SETTINGS....................................................................... 124
7.4.1 Flash Descriptor Security Override Jumper (ME_FLASH1)........................ 124
7.4.2 LVDS Panel Voltage Selection Jumper (J_VLVDS1)..................................... 124
7.4.3 LVDS Panel Resolution Selection Jumper (SW1).......................................... 125
7.4.4 PCIe Mini/mSATA Mode Selection (MSATA_CN1) ....................................... 125
Page viii
Page 9
POC-W24C-ULT3 FHD Medical Panel PC
A REGULATORY COMPLIANCE............................................................................ 126
B SAFETY PRECAUTIONS....................................................................................... 131
B.1 SAFETY PRECAUTIONS........................................................................................... 132
B.1.1 General Safety Precautions........................................................................... 132
B.1.2 Anti-static Precautions.................................................................................. 133
B.1.3 Product Disposal........................................................................................... 134
B.1.4 Classification................................................................................................. 135
B.2 MAINTENANCE AND CLEANING PRECAUTIONS...................................................... 135
B.2.1 Maintenance and Cleaning............................................................................ 136
B.2.2 Cleaning Tools............................................................................................... 136
C BIOS MENU OPTIONS........................................................................................... 137
D WATCHDOG TIMER.............................................................................................. 140
E HAZARDOUS MATERIALS DISCLOSURE ....................................................... 143
Page ix
Page 10
POC-W24C-ULT3 FHD Medical Panel PC
List of Figures
Figure 1-1: POC-W24C-ULT3 FHD Medical Panel PC..................................................................2
Figure 1-2: Front View....................................................................................................................4
Figure 1-3: Backlit Touch Buttons................................................................................................5
Figure 1-4: Left View.......................................................................................................................6
Figure 1-5: Bottom Panel...............................................................................................................7
Figure 1-6: Rear View.....................................................................................................................8
Figure 1-7: Dimensions (mm)......................................................................................................12
Figure 3-1: Back Cover Retention Screws.................................................................................21
Figure 3-2: HDD Bracket Retention Screws...............................................................................22
Figure 3-3: HDD Installation ........................................................................................................23
Figure 3-4: Handset Holder Retention Screws..........................................................................24
Figure 3-5: Handset Installation..................................................................................................24
Figure 3-6: Handset Driver Folder...............................................................................................25
Figure 3-7: Handset Driver Installation.......................................................................................26
Figure 3-8: Allow API Access......................................................................................................26
Figure 3-9: Manage Program Access to Skype.........................................................................27
Figure 3-10: Handle Installation..................................................................................................29
Figure 3-11: Insert Barcode Reader Set.....................................................................................30
Figure 3-12: Install and Connect Barcode Reader Set..............................................................30
Figure 3-13: Barcode Reader Button..........................................................................................31
Figure 3-14: Reading Light..........................................................................................................31
Figure 3-15: 3-in-1 Combo Reader..............................................................................................32
Figure 3-16: USB Ports on the Left Panel ..................................................................................32
Figure 3-17: Combo Reader Installation ....................................................................................33
Figure 3-18: RFID Program Location..........................................................................................34
Figure 3-19: IRFR-100 Icon ..........................................................................................................34
Figure 3-20: IRFR Screen.............................................................................................................34
Figure 3-21: IRFR – Find Tags.....................................................................................................35
Figure 3-22: IRFR – UIDs..............................................................................................................35
Figure 3-23: AT/ATX Switch Location.........................................................................................37
Figure 3-24: Wall-mounting Bracket...........................................................................................38
Page x
Page 11
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-25: Chassis Support Screws........................................................................................40
Figure 3-26: Secure the Panel PC...............................................................................................40
Figure 3-27: VESA 75 and VESA 100 Mounting Retention Screw Holes.................................42
Figure 3-28: Arm Mounting..........................................................................................................42
Figure 3-29: Power Input Connector...........................................................................................44
Figure 3-30: Reset Button Location............................................................................................44
Figure 5-1: Available Drivers.......................................................................................................80
Figure 5-2: Intel® Chipset Device Software Installation Wizard..............................................81
Figure 5-3: Intel® Graphics Driver Installation Wizard.............................................................82
Figure 5-4: Realtek HD Audio Driver InstallShield Wizard .......................................................83
Figure 5-5: LAN Driver Installation Wizard ................................................................................84
Figure 5-6: Intel® ME Components Installation Wizard............................................................85
Figure 5-7: Wireless LAN InstallShield Wizard..........................................................................86
Figure 5-8: Bluetooth Driver InstallShield Wizard.....................................................................87
Figure 5-9: Keypad AP Setup Wizard .........................................................................................88
Figure 5-10: Keypad AP...............................................................................................................88
Figure 5-11: Device Manager - Update Driver Software............................................................89
Figure 5-12: Update Driver Software Window ...........................................................................90
Figure 5-13: Browse for Driver Software Window.....................................................................90
Figure 5-14: Driver Installation Complete Window ...................................................................91
Figure 5-15: Device Manager Window–RFID Devices...............................................................91
Figure 5-16: Device Manager - Update Driver Software............................................................92
Figure 5-17: Update Driver Software Window ...........................................................................93
Figure 5-18: Browse for Driver Software Window.....................................................................93
Figure 5-19: Installing Driver Window........................................................................................94
Figure 5-20: Driver Installation Complete Window ...................................................................94
Figure 5-21: Device Manager Window–SCR Device..................................................................95
Figure 5-22: Device Manager - Update Driver Software............................................................96
Figure 5-23: Update Driver Software Window ...........................................................................97
Figure 5-24: Browse for Driver Software Window.....................................................................97
Figure 5-25: Installing Driver Window........................................................................................98
Figure 5-26: Driver Installation Complete Window ...................................................................98
Figure 5-27: Device Manager Window–MSR Device.................................................................99
Figure 5-28: Fingerprint Reader Driver Folder ..........................................................................99
Figure 5-29: Fingerprint Reader Driver InstallShield Wizard ................................................ 100
Page xi
Page 12
Figure 5-30: Barcode Reader Driver Folder............................................................................ 101
Figure 5-31: Barcode Reader Driver Installation.................................................................... 101
Figure 5-32: Device Manager Window–Barcode Reader Device .......................................... 102
Figure 6-1: Back Cover Retention Screws.............................................................................. 105
Figure 6-2: Aluminum Cover Retention Screws..................................................................... 106
Figure 6-3: SO-DIMM Slot Locations ....................................................................................... 107
Figure 6-4: SO-DIMM Installation............................................................................................. 107
Figure 6-5: PCIe Mini Card Slot Location................................................................................ 108
Figure 6-6: PCIe Mini Card Installation.................................................................................... 109
Figure 7-1: Main Board Layout Diagram................................................................................. 111
POC-W24C-ULT3 FHD Medical Panel PC
Page xii
Page 13
POC-W24C-ULT3 FHD Medical Panel PC
List of Tables
Table 1-1: Model Variations...........................................................................................................3
Table 1-2: Touch Button Functions..............................................................................................5
Table 1-3: System Specifications................................................................................................11
Table 3-1: Handset Button Functions.........................................................................................28
Table 3-2: RS-232/422/485 Serial Port Pinouts..........................................................................36
Table 4-1: BIOS Navigation Keys................................................................................................47
Table 7-1: Peripheral Interface Connectors............................................................................ 113
Table 7-2: Audio Connector (AUDIO_OUT1) Pinouts............................................................. 113
Table 7-3: Audio Out Connector (AMP_OUT1) Pinouts......................................................... 113
Table 7-4: Battery Connector (BAT1) Pinouts........................................................................ 113
Table 7-5: Debug Connector (DBG_PORT1) Pinouts............................................................. 114
Table 7-6: Inverter Connector (INVERTER1) Pinouts............................................................. 114
Table 7-7: LVDS Connector (LVDS1) Pinouts......................................................................... 115
Table 7-8: MCU Connector (HOTKEY_CN1) Pinouts.............................................................. 115
Table 7-9: MCU Flash Connector (JP8) Pinouts..................................................................... 116
Table 7-10: MCU Flash SPI ROM Connector (MCU_SPI1) Pinouts....................................... 116
Table 7-11: Microphone Connector (DMIC1) Pinouts ............................................................ 116
Table 7-12: Power Button Connector (PWR_BTN1) Pinouts................................................. 117
Table 7-13: Power LED Connector (PW_LED1) Pinouts........................................................ 117
Table 7-14: RS-232 Serial Port Connector (COM2) Pinouts .................................................. 117
Table 7-15: SATA Connectors (SATA1 & SATA2) Pinouts.................................................... 118
Table 7-16: SPI Flash Connector (JSPI1) Pinouts.................................................................. 118
Table 7-17: TPM Connector (TPM1) Pinouts........................................................................... 119
Table 7-18: USB Connector (BT_USB1) Pinouts.................................................................... 119
Table 7-19: USB Connector (CAM_USB1) Pinouts................................................................. 119
Table 7-20: USB Connector (RFID_USB1) Pinouts ................................................................ 120
Table 7-21: USB Connector (TOUCH_USB1) Pinouts............................................................ 120
Table 7-22: Rear Panel Connectors......................................................................................... 121
Table 7-23: GbE Connectors (LAN1 & LAN2) Pinouts........................................................... 121
Table 7-24: HDMI Connector (HDMI1) Pinouts........................................................................ 122
Table 7-25: Power Connector (PWR1) Pinouts....................................................................... 122
Page xiii
Page 14
Table 7-26: RS-232/422/485 DB-9 Serial Port (COM1) Pinouts.............................................. 122
Table 7-27: USB 2.0 Connector (USB20_CN1) Pinouts.......................................................... 122
Table 7-28: USB 3.0 Connector (USB_CON12) Pinouts......................................................... 123
Table 7-29: USB 3.0 Connector (USB_CON2) Pinouts........................................................... 123
Table 7-30: Preconfigured Jumpers ........................................................................................ 124
Table 7-31: Flash Descriptor Security Override Jumper (ME_FLASH1) Settings............... 124
Table 7-32: LVDS Voltage Selection Jumper (J_VLVDS1) Settings..................................... 124
Table 7-33: LVDS Resolution Selection Jumper (SW1) Settings.......................................... 125
Table 7-34: PCIe Mini/mSATA Mode Selection (MSATA_CN1) Settings.............................. 125
POC-W24C-ULT3 FHD Medical Panel PC
Page xiv
Page 15
POC-W24C-ULT3 FHD Medical Panel PC
List of BIOS Menus
BIOS Menu 1: Main.......................................................................................................................48
BIOS Menu 2: Advanced..............................................................................................................49
BIOS Menu 3: Trusted Computing..............................................................................................50
BIOS Menu 4: ACPI Settings .......................................................................................................51
BIOS Menu 5: F81866 Super IO Configuration..........................................................................52
BIOS Menu 6: Serial Port n Configuration Menu.......................................................................52
BIOS Menu 7: F81866 H/W Monitor.............................................................................................55
BIOS Menu 8: RTC Wake Settings..............................................................................................56
BIOS Menu 9: Serial Port Console Redirection.........................................................................57
BIOS Menu 10: Console Redirection Settings...........................................................................58
BIOS Menu 11: Legacy Console Redirection Settings .............................................................60
BIOS Menu 12: CPU Configuration.............................................................................................61
BIOS Menu 13: SATA Configuration...........................................................................................63
BIOS Menu 14: USB Configuration.............................................................................................65
BIOS Menu 15: IEI Feature...........................................................................................................66
BIOS Menu 16: Chipset................................................................................................................67
BIOS Menu 17: System Agent (SA) Configuration....................................................................67
BIOS Menu 18: Graphics Configuration.....................................................................................68
BIOS Menu 19: LCD Control........................................................................................................70
BIOS Menu 20: Memory Configuration.......................................................................................71
BIOS Menu 21: PCH-IO Configuration........................................................................................71
BIOS Menu 22: PCI Express Configuration ...............................................................................72
BIOS Menu 23: HD Audio Configuration....................................................................................73
BIOS Menu 24: Security...............................................................................................................74
BIOS Menu 25: Boot.....................................................................................................................75
BIOS Menu 26: Save & Exit..........................................................................................................77
Page xv
Page 16
POC-W24C-ULT3 FHD Medical Panel PC
Chapter
1
1 Introduction
Page 1
Page 17
1.1 Overview
Figure 1-1: POC-W24C-ULT3 FHD Medical Panel PC
POC-W24C-ULT3 FHD Medical Panel PC
th
The POC-W24C-ULT3 is a 6
medical-grade panel PC with a rich variety of functions and peripherals. All
POC-W24C-ULT3 models are designed for easy and simplified integration into
point-of-care (POC) applications. The system comes with 4 GB of preinstalled DDR4
memory and supports a maximum of 32 GB ensuring smooth data throughputs with
reduced bottlenecks and fast system access.
One RS-232/422/485 serial port, four USB 3.0 ports and four USB 2.0 ports provide
simplified connectivity to a variety of external peripheral devices. Wi-Fi 802.11a/b/g/n/ac
high speed wireless and two RJ-45 GbE connectors allow for smooth connection of the
system to an external LAN.
generation Intel® Core™/Celeron® mobile CPU powered
NOTE:
The POC-W24C-ULT3 medical panel PC is intended to be used to display
general purpose medical images. The device shall not be used for diagnosis
Page 2
purpose or life supporting system.
Page 18
POC-W24C-ULT3 FHD Medical Panel PC
1.2 Model Variations
There are three models in the POC-W24C-ULT3 series. All models are preinstalled with
one 4 GB DDR4 memory module and an 802.11a/b/g/n/ac Wi-Fi module. The model
numbers and model variations are listed below.
Model CPU
POC-W24C-ULT3-i7/PC/4G
POC-W24C-ULT3-i5/PC/4G
POC-W24C-ULT3-C/PC/4G
Table 1-1: Model Variations
1.3 Features
The POC-W24C-ULT3 features are listed below:
24” fanless FHD medical-grade panel PC
Anti-bacteria cover
Projected capacitive type touchscreen
Intel® Core™ i7-6600U/i5-6300U or Intel® Celeron® 3855U processor
Preinstalled with 4 GB of DDR4 memory (system max. 32 GB)
Two GbE RJ-45 connectors and Wi-Fi 802.11a/b/g/n/ac high speed wireless
Two internal 3 W speakers
Intel® Core™ i7-6600U
Intel® Core™ i5-6300U
Intel® Celeron® 3855U
Four USB 3.0 ports and four USB 2.0 ports
12 V ~ 28 V wide range DC power input
One RS-232/422/485 DB-9 connector
IP 65 compliant front panel
Optional Mifare RFID reader
Optional 3-in-1 card reader (supports magnetic stripe card, smart card and
fingerprint)
Optional VoIP phone handset
Optional handle module with 1D/2D barcode scanner and reading light
Page 3
Page 19
1.4 Front Panel
The front side of the POC-W24C-ULT3 is a flat-bezel panel with a TFT LCD screen
POC-W24C-ULT3 FHD Medical Panel PC
surrounded by a PC+ABS plastic frame (
Figure 1-2).
Page 4
Figure 1-2: Front View
Page 20
POC-W24C-ULT3 FHD Medical Panel PC
1.4.1 Backlit Touch Buttons
The front panel of the POC-W24C-ULT3 contains several backlit touch buttons that control
audio volume, LCD brightness and some other system components.
Figure 1-3: Backlit Touch Buttons
The following table describes the function of each button.
Button Function
LCD on/off
(the touch buttons blink when the LCD is turned off)
−: Brightness down or lock/unlock OSD (with function key)
(minimum brightness: 5%)
+: Brightness up (maximum brightness: 100%)
−: Volume down
+: Volume up
Touch lock for cleaning: long-press for 3 seconds to lock or
unlock the touch function of the screen. The touch buttons
blink when the touch function is locked. The lock will be
automatically disabled after 2 minutes.
Lock or unlock the touch buttons: long-press for 3 seconds
to lock or unlock the touch buttons. The touch buttons blink
when the touch buttons are locked.
Power on: long-press for 3 seconds. All touch buttons blink
3 times, and the system starts to boot.
Power off: long-press for 3 seconds. All touch buttons blink
3 times, and the system starts to shut down.
Note: Press the touch button for at least one second to activate it.
Table 1-2: Touch Button Functions
Page 5
Page 21
1.5 Left Panel
The left side panel has the power button, two USB 2.0 ports which are protected by a
waterproof cover and the IEI E-Window for I/O interface expansion by installing a PCIe
Mini card.
POC-W24C-ULT3 FHD Medical Panel PC
Page 6
Figure 1-4: Left View
Page 22
POC-W24C-ULT3 FHD Medical Panel PC
1.6 Bottom Panel
The bottom panel of the POC-W24C-ULT3 has the following connectors and switches
(
Figure 1-5):
1 x 12 V ~ 28 V DC input power jack
1 x RS-232/422/485 DB-9 connector
1 x Barcode reader RJ-11 connector
2 x GbE RJ-45 connectors
4 x USB 3.0 connectors
2 x USB 2.0 connectors
1 x HDMI output connector
1 x AT/ATX switch
1 x Reset button
Figure 1-5: Bottom Panel
Page 7
Page 23
1.7 Rear Panel
The rear panel contains two 3 W speakers, the camera cover on/off switch and the
POC-W24C-ULT3 FHD Medical Panel PC
retention screw holes that support VESA 75/100 mounting (
panel has several screw holes for installing the optional items, such as the 3-in-1 reader.
For detailed information on installation of the optional items, please refer to Chapter 3.
Figure 1-6). Besides, the rear
Figure 1-6: Rear View
1.8 System Specifications
The technical specifications for the POC-W24C-ULT3 systems are listed in Table 1-3.
LCD and Touchscreen
24"
1920 (W) x 1080 (H)
250
1000:1
Page 8
LCD Size
Max. Resolution
Brightness (cd/m2)
Contrast Ratio
Page 24
POC-W24C-ULT3 FHD Medical Panel PC
LCD Color
Pixel Pitch (mm)
Viewing Angle (H-V)
Backlight MTBF
Touchscreen
Touch Controller
Surface Hardness
System
CPU
Memory
16.7M (RGB 6-bit + Hi-FRC)
0.2745 (H) x 0. 2745 (V)
178°/178°
30,000 hrs (LED backlight)
Projected capacitive type with USB interface
EETI
6H
Intel® Core™ i7-6600U/i5-6300U or Intel® Celeron® 3855U
Two 260-pin 2133/1866 MHz dual-channel non-ECC
unbuffered DDR4 SO-DIMMs supported (system max. 32 GB)
Preinstalled with 4 GB memory
1 x 12 V ~ 28 V DC input jack
1 x Barcode reader connector (RJ-11)
I/O Ports
Storage
Audio
Webcam & Microphone
Expansion Interface
LED Indicator
TPM
1 x HDMI output connector
1 x RS-232/422/485 serial port (DB-9 connector)
2 x GbE LAN (RJ-45 connector)
4 x USB 3.0 connectors
4 x USB 2.0 connectors (2 on side panel)
One 2.5” SATA 6Gb/s HDD bay
One mSATA (reserved, PCIe Mini interface)
Two 3 W speakers
5-megapixel CMOS front-facing camera with auto focus and
digital microphone
One PCIe Mini slot (reserved for E-Window expansion)
RFID indicator (optional)
TPM 1.2 (optional)
Page 9
Page 25
Other Features
POC-W24C-ULT3 FHD Medical Panel PC
Mifare RFID
Function Keys
Combinations:
Light Sensor
Cooling Method
Connectivity
Wi-Fi and Bluetooth
Optional Mifare 13.56 MHz card reader (with LED indicator)
1 x LCD on/off
1 x Brightness up
1 x Brightness down
1 x Volume up
1 x Volume down
1 x Touch lock for cleaning
1 x Lock/unlock OSD
1 x Power on/off
Ambient light sensor for panel brightness adjustment
Fanless
Intel® dual-band wireless – AC 8265, Bluetooth v4.2
(M.2 2230 module)
LAN
Physical
Construction Material
Mounting
Net Weight
Dimensions (W x H x D)
Environment
Storage/Transportation
Two GbE LAN connectors
PC+ABS plastic with anti-bacterial material
Wall, stand and arm mounting
VESA 75 mm x 75 mm or 100 mm x 100 mm
7.5 kg
594.6 mm x 379.6 mm x 60.68 mm
Temperature
Humidity
Pressure
-20ºC ~ 60ºC
10% ~ 95% (non-condensing)
700 hPa ~ 1060 hPa
Page 10
Page 26
POC-W24C-ULT3 FHD Medical Panel PC
Operating
Vibration
Shock
IP Level
Power
Power Input
Power Adapter
Temperature
Humidity
Pressure
1G
Operating Shock: 5G peak acceleration (11ms duration)
Non-Operating Shock: 15G peak acceleration (11ms duration)
IP 65 compliant front panel
12 V ~ 28 V DC
120 W medical-grade power
adapter
(P/N: 63040-010120-010-RS)
Input: 100 V AC ~ 240 V AC,
47 Hz ~ 63 Hz, 1.4 A ~ 0.6 A
0ºC ~ 40ºC
10% ~ 95% (non-condensing)
700 hPa ~ 1060 hPa
150 W medical-grade power
adapter
(P/N: 63040-010150-400-RS)
Input: 100 V AC ~ 240 V AC,
47 Hz ~ 63 Hz, 2 A ~ 0.85 A
Output: 19 V
Table 1-3: System Specifications
6.32 A Output: 19 V 7.89 A
Page 11
Page 27
1.9 Dimensions
The POC-W24C-ULT3 dimensions are shown below.
POC-W24C-ULT3 FHD Medical Panel PC
Page 12
Figure 1-7: Dimensions (mm)
Page 28
POC-W24C-ULT3 FHD Medical Panel PC
Chapter
2
2 Unpacking
Page 13
Page 29
2.1 Unpacking
To unpack the medical panel PC, follow the steps below:
WARNING!
The front side LCD screen has a protective plastic cover stuck to the
screen. Only remove the plastic cover after the medical panel PC has been
properly installed. This ensures the screen is protected during the
installation process.
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
external (second) box.
POC-W24C-ULT3 FHD Medical Panel PC
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
internal (first) box.
Step 4: Lift the monitor out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Pull the plastic cover off the medical panel PC.
Step 7: Make sure all the components listed in the packing list are present. Step 0:
Page 14
Page 30
POC-W24C-ULT3 FHD Medical Panel PC
2.2 Packing List
NOTE:
If any of the components listed in the checklist below are missing, do not
proceed with the installation. Contact the IEI reseller or vendor the
POC-W24C-ULT3 was purchased from or contact an IEI sales representative
directly by sending an email to
The POC-W24C-ULT3 medical panel PC is shipped with the following components:
Quantity Item Image
1
1 120 W/19 V medical-grade power adapter
POC-W24C-ULT3 medical panel PC
(P/N: 63040-010120-010-RS)
or
150 W/19 V medical-grade power adapter
(P/N: 63040-010150-400-RS)
32sales@ieiworld.com.
1 Power cord
(P/N: 32702-000200-100-RS)
4 Pan-head screw (M3*5) for HDD installation
(P/N: 44043-030051-RS)
Page 15
Page 31
1 Quick Installation Guide
1 Utility CD
1 One Key Recovery CD
2.3 Optional Items
POC-W24C-ULT3 FHD Medical Panel PC
The following are optional components which may be separately purchased:
Item and Part Number Image
3-in-1 reader (smart card, magnetic card and fingerprint)
(P/N: MEDP-CR-R10)
Handle
(P/N: MEDP-HD-R10)
Handle with 1D/2D barcode reader and reading light
(P/N: MEDP-HD-BR-R10)
Page 16
Page 32
POC-W24C-ULT3 FHD Medical Panel PC
Item and Part Number Image
Handset (USB interface) and holder
(P/N: MEDP-HS-R10)
VESA 100 wall mount kit (four M3*6 screws included)
(P/N: AFLWK-19B)
Arm
(P/N: ARM-31-RS)
Stand
(P/N: STAND-A21-R10)
EZ Stand with cabling hole, VESA 100
(P/N: MEDP-EZS-R10)
Page 17
Page 33
Item and Part Number Image
POC-W24C-ULT3 FHD Medical Panel PC
Trusted platform module (assemble-to-order)
(P/N: MEDP-TPM-R10)
Mifare RFID reader compliant with ISO 14443A, ISO
14443B and ISO 15693 protocols (assemble-to-order)
(P/N: MEDP-MF-RFID-R10)
Page 18
Page 34
POC-W24C-ULT3 FHD Medical Panel PC
3 Installation
Chapter
3
Page 19
Page 35
3.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the maintenance of the
POC-W24C-ULT3 may result in permanent damage to the
POC-W24C-ULT3 and severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the POC-W24C-ULT3. Dry climates are especially susceptible to ESD. It is
therefore critical that whenever the POC-W24C-ULT3 is accessed internally, or any other
electrical component is handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
POC-W24C-ULT3 FHD Medical Panel PC
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board, touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the POC-W24C-ULT3, place it on
an anti-static pad. This reduces the possibility of ESD damaging the
POC-W24C-ULT3.
Only handle the edges of the PCB: When handling the PCB, hold the PCB
by the edges.
3.2 Installation Precautions
When installing the medical panel PC, please follow the precautions listed below:
Manufacturer authorization: Do not modify this equipment without
authorization of manufacturer.
Certified Engineers: Only certified engineers should install and modify the
hardware settings.
Page 20
Power turned off: When installing the medical panel PC, make sure the
power is off. Failing to turn off the power may cause severe injury to the body
and/or damage to the system.
Page 36
POC-W24C-ULT3 FHD Medical Panel PC
Anti-static Discharge : If a user open the rear panel of the medical panel PC,
to configure the jumpers or plug in added peripheral devices, ground
themselves first and wear an anti-static wristband.
3.3 Installation and Configuration Steps
The following installation steps must be followed.
Step 1: Unpack the medical panel PC.
Step 2: Install an HDD.
Step 3: Install necessary accessories (handset, handle or combo reader).
Step 4: Configure the system.
Step 5: Connect peripheral devices to the medical panel PC.
Step 6: Mount the medical panel PC. Step 0:
3.4 HDD Installation
To install the HDD into the system, please follow the steps below:
Step 1: Remove the twelve retention screws from the back cover (
Figure 3-1).
Figure 3-1: Back Cover Retention Screws
Page 21
Page 37
Step 2: Remove the back cover.
POC-W24C-ULT3 FHD Medical Panel PC
Step 3: Remove the six HDD bracket retention screws (
bracket off the panel PC.
Figure 3-2: HDD Bracket Retention Screws
Figure 3-2) and lift the HDD
Step 4: Place the HDD into the HDD bracket, aligning the four retention screw holes in
the both sides of the HDD bracket with the retention screw holes on the sides of
the HDD (
Step 5: Insert four retention screws (M3*5) into the bracket (
Figure 3-3).
Figure 3-3).
Page 22
Page 38
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-3: HDD Installation
Step 6: Connect the SATA cable from the POC-W24C-ULT3 to the rear of the HDD
Figure 3-3).
(
Step 7: Replace the HDD bracket by securing the six retention screws previously
removed (
Step 8: Replace the back cover. Step 0:
Figure 3-2).
3.5 Handset Installation (Optional)
An optional phone handset can be installed on the side of the POC-W24C-ULT3 to make
VoIP calls. To install the handset and the holder, please follow the instruction below.
Step 1: Locate the two retention screw holes for installing the handset holder on the rear
panel (
Figure 3-4).
Page 23
Page 39
Step 2: Secure the handset holder with the POC-W24C-ULT3 by two retention screws
(M3*8, flat head).
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-4: Handset Holder Retention Screws
Step 3: Plug the handset cord into a USB connector on the bottom panel.
Step 4: Place the handset in the holder.
Page 24
Figure 3-5: Handset Installation
Page 40
POC-W24C-ULT3 FHD Medical Panel PC
3.5.1 Using VoIP Handset
The VoIP handset is designed for Skype. To use the handset to place or receive a call via
Skype, please follow the steps below.
Step 1: Install the Skype program (
Step 2: Select Other from the list of the driver CD. Double click the setup file in the
POCP-W22A-HS-R10_U-2000H folder to install the handset driver (
Figure 3-6: Handset Driver Folder
Step 3: Follow the step-by-step instruction of the installation wizard (
install the handset driver.
http://www.skype.com/en/).
476Figure 3-6).
Figure 3-7) to
Page 25
Page 41
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-7: Handset Driver Installation
Step 4: Launch Skype. Press the Allow access button on Skype (
handset API access.
Figure 3-8: Allow API Access
Figure 3-8) to allow
Page 26
Page 42
POC-W24C-ULT3 FHD Medical Panel PC
API access can also be managed through Tools Æ Options Æ Advanced
settings in Skype. See
Figure 3-9.
Figure 3-9: Manage Program Access to Skype
Page 27
Page 43
Step 5: The user can now use Skype via the handset. The function description of each
button on the handset is listed in the following table.
Button Function
LED indicator:
Clear–no call activity
Blinking green–incoming call ringing
Steady green–active call
POC-W24C-ULT3 FHD Medical Panel PC
i
j
Hot key:
No call activity–launch Skype and select menus
* long-press the hot key for 2 seconds to turn off Skype
Ringing–terminate the incoming call
Active call–mute or unmute the handset microphone
No call activity–scroll up through incoming and outgoing call history
Active call–handset speaker volume up
No call activity–scroll down through incoming and outgoing call history
Active call–handset speaker volume down
§
Table 3-1: Handset Button Functions
Place, answer or hang up a call.
Page 28
Page 44
POC-W24C-ULT3 FHD Medical Panel PC
3.6 Handle Installation (Optional)
An optional handle can be installed on the POC-W24C-ULT3 for the user to easily adjust
the viewing angle and the position of the POC-W24C-ULT3. To install the handle, please
follow the instruction below.
Step 1: Locate the retention screw holes for installing the handle on the rear panel
(
Figure 3-10). If a cable cover is installed on the rear panel, please remove it
first.
Step 2: Secure the handle with the POC-W24C-ULT3 by inserting eight retention screws
(M3*6L, flat head).
Figure 3-10: Handle Installation
3.6.1 Barcode Reader Installation
The optional handle may come with a barcode reader set which also contains a reading
light with three levels of brightness. To install the barcode reader set, please follow the
instruction below.
Step 1: Follow the instruction described in Section
Step 2: Insert the barcode reader set into the slot in the center of the handle. To be able
to insert the barcode reader, the side with barcode reader must face toward the
right side of the POC-W24C-ULT3 as shown in
3.6 to install the handle.
Figure 3-11.
Page 29
Page 45
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-11: Insert Barcode Reader Set
Step 3: Push the barcode reader set all the way down, and then rotate the barcode
reader anti-clockwise to a proper position (
Step 4: Connect the barcode reader cable to the RJ-11 connector on the bottom panel of
the POC-W24C-ULT3 (
Figure 3-12).
Figure 3-12).
Page 30
Figure 3-12: Install and Connect Barcode Reader Set
Step 5: Install the driver for the barcode reader by following the instructions described in
Section
5.12.
Page 46
POC-W24C-ULT3 FHD Medical Panel PC
Step 6: After driver installation is complete, push the barcode reader button to trigger the
barcode reader.
Figure 3-13: Barcode Reader Button
WARNING:
Do not stare into beam of the laser light. The human eye can be
damaged. Avoid that the laser beam hits reflective surfaces such as
mirrors, etc. Any changes at the device are forbidden these could
cause a dangerous laser light.
3.6.2 Reading Light
The barcode reader is also equipped with a reading light with 3-level of brightness. Push
the reading light button to turn on or to toggle illumination brightness levels.
Figure 3-14: Reading Light
Page 31
Page 47
POC-W24C-ULT3 FHD Medical Panel PC
3.7 3-in-1 Combo Reader Installation (Optional)
The 3-in-1 combo reader is an optional item for the POC-W24C-ULT3. The combo reader
combines fingerprint reader, smart card reader (SCR) and magnetic stripe reader (MSR)
into one compact device.
Figure 3-15: 3-in-1 Combo Reader
To install the combo reader to the POC-W24C-ULT3, please follow the steps below.
Step 1: Open the USB port cover on the left panel of the POC-W24C-ULT3.
Figure 3-16: USB Ports on the Left Panel
Step 2: Align the USB connectors on the reader with the two USB connectors on the left
Page 32
panel of the POC-W24C-ULT3.
Step 3: Insert and connect the USB connectors to install the combo reader.
Page 48
POC-W24C-ULT3 FHD Medical Panel PC
Step 4: Secure the combo reader to the system by inserting two retention screws
(M3x5L) into the rear panel of the POC-W24C-ULT3 and tightening them.
Figure 3-17: Combo Reader Installation
Step 5: Install the drivers for these three readers by following the instructions described
in Chapter 5:
Section
Section
Section
5.11.1: SCR Driver
5.11.2: MSR Driver
5.11.3: Fingerprint Reader Driver
3.8 Using RFID Reader (Optional)
The POC-W24C-ULT3 may come with an optional RFID reader pre-installed inside the
bottom left corner of the front panel (
below.
Step 1: Install the RFID driver (refer to Section
Step 2: Locate the IRFR-100.exe file in the following folder of the driver CD:
Figure 1-2). To use the RFID reader, follow the steps
5.10).
\Docs\12.Other\POCP-MF-RFID-R10\RFID\D490. Copy the IRFR-100.exe
program to the desktop.
Page 33
Page 49
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-18: RFID Program Location
Step 3: Double click the IRFR-100 icon on the desktop.
Figure 3-19: IRFR-100 Icon
Step 4: The IRFR-100 window appears (
6Figure 3-20).
Figure 3-20: IRFR Screen
Step 5: Select the Find tags tab and click the Run button to enable the RFID reader
Page 34
(
6Figure 3-21).
Page 50
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-21: IRFR – Find Tags
Step 6: Place an RFID card near the RFID reader
front panel (
UIDs column (
Figure 3-22: IRFR – UIDs
Figure 1-2) then remove it. The card number will be shown in the
6Figure 3-22).
on the bottom right corner of the
Page 35
Page 51
POC-W24C-ULT3 FHD Medical Panel PC
NOTE:
Please refer to the IRFR-100 user guide in the driver CD
(IRFR-100_AP_UserGuide.pdf) for detailed instruction on how to use
the IRFR-100.
3.9 RS-232/422/485 Serial Port Connection
The bottom panel of the POC-W24C-ULT3 has one DB-9 male connectors for
RS-232/422/485 connection. The serial communication mode selection can be made
through the BIOS options. Please refer to Section
4.3.3.1.1 for detailed information. The
pinouts of the DB-9 connector are listed below.
Pin RS-232 RS-422 RS-485
1 DCD TXD422- TXD4852 RX TXD422+ TXD485+
3 TX RXD422+
4 DTR RXD422-
5 GND
6 DSR
7 RTS
8 CTS
9 RI
Table 3-2: RS-232/422/485 Serial Port Pinouts
Page 36
Page 52
POC-W24C-ULT3 FHD Medical Panel PC
3.10 AT/ATX Mode Selection
AT or ATX power mode can be used on the POC-W24C-ULT3. The selection is made
through an AT/ATX switch located on the bottom panel (
Figure 3-23: AT/ATX Switch Location
Figure 3-23).
3.10.1 AT Power Mode
With the AT mode selected, the power is controlled by a central power unit rather than a
power switch. The POC-W24C-ULT3 panel PC turns on automatically when the power is
connected.
3.10.2 ATX Power Mode
With the ATX mode selected, the POC-W24C-ULT3 panel PC goes in a standby mode
when it is turned off. The panel PC can be easily turned on via network or a power switch
in standby mode.
3.11 Mounting the System
The methods of mounting the POC-W24C-ULT3 are listed below.
Wall mounting
Arm mounting
Stand mounting
The mounting methods are described below.
WARNING:
Use suitable mounting apparatus and be sure to secure the screws of
the mounting apparatus tightly to avoid risk of injury.
Page 37
Page 53
3.11.1 Wall Mounting
To mount the medical panel PC onto the wall, please follow the steps below.
Step 1: Select the location on the wall for the wall-mounting bracket.
Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall.
Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention
screws.
Step 4: Align the wall-mounting bracket screw holes with the pilot holes.
Step 5: Secure the mounting bracket to the wall by inserting the retention screws into
POC-W24C-ULT3 FHD Medical Panel PC
the four pilot holes and tightening them (
Figure 3-24).
Figure 3-24: Wall-mounting Bracket
Step 6: Insert the four monitor mounting screws provided in the wall mount kit into the
four screw holes on the real panel of the medical panel PC and tighten until the
screw shank is secured against the rear panel (
Figure 3-25).
Page 38
Page 54
POC-W24C-ULT3 FHD Medical Panel PC
WARNING:
Please use the M4 screws provided in the wall mount kit for the rear panel.
If the screw is missing, the thread depth of the replacement screw should
be not more than 4 mm.
Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on
the bracket.
Step 8: Carefully insert the screws through the holes and gently pull the monitor
downwards until the monitor rests securely in the slotted holes (
Ensure that all four of the mounting screws fit snugly into their respective slotted
holes.
Figure 3-25).
NOTE:
In the diagram below the bracket is already installed on the wall.
Page 39
Page 55
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-25: Chassis Support Screws
Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting
bracket (
Figure 3-26).
Page 40
Figure 3-26: Secure the Panel PC
Page 56
POC-W24C-ULT3 FHD Medical Panel PC
3.11.2 Arm Mounting
The POC-W24C-ULT3 is VESA (Video Electronics Standards Association) compliant and
can be mounted on an arm with a 75 mm or a 100 mm interface pad. To mount the
POC-W24C-ULT3 on an arm, please follow the steps below.
Step 1: The arm is a separately purchased item. Please correctly mount the arm onto
the surface it uses as a base. To do this, refer to the installation documentation
that came with the mounting arm.
NOTE:
When purchasing the arm please ensure that it is VESA compliant and that
the arm has a 75 mm or a 100 mm interface pad. If the mounting arm is not
VESA compliant it cannot be used to support the POC-W24C-ULT3
medical panel PC.
Step 2: Once the mounting arm has been firmly attached to the surface, lift the panel PC
onto the interface pad of the mounting arm.
Step 3: Align the retention screw holes on the mounting arm interface with those in the
panel PC (
Figure 3-27).
Page 41
Page 57
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-27: VESA 75 and VESA 100 Mounting Retention Screw Holes
Step 4: Secure the POC-W24C-ULT3 to the interface pad by inserting four retention
screws through the mounting arm interface pad and into the POC-W24C-ULT3.
Page 42
Figure 3-28: Arm Mounting
Page 58
POC-W24C-ULT3 FHD Medical Panel PC
3.11.3 Stand Mounting
To mount the POC-W24C-ULT3 using the stand mounting kit, please follow the steps
below.
Step 1: Locate the VESA mounting screw holes on the rear of the POC-W24C-ULT3
Figure 3-27). This is where the bracket will be attached.
(
Step 2: Align the bracket of the stand with the screw holes.
Step 3: To secure the bracket to the POC-W24C-ULT3, insert the retention screws into
the screw holes and tighten them.
NOTE:
If the EZ stand (MEDP-EZS-R10) is mounted, the handle
(MEDP-HD-R10 or MEDP-HD-BR-R10) can not be installed.
3.12 Powering On the System
WARNING:
To avoid risk of electric shock, this equipment must only be connected
to supply mains with protective earth.
CAUTION:
The FSP PMP120-13-2 power adapter came with the
POC-W24C-ULT3 is a forming part of the medical device.
Page 43
Page 59
To power on the system, follow the steps below:
Step 1: Connect the power cord to the power adapter. Connect the other end of the
power cord to a power source.
Step 2: Connect the power adapter to the power connector of the POC-W24C-ULT3.
POC-W24C-ULT3 FHD Medical Panel PC
Step 3: Locate the power button on the left panel (
Step 4: Short press the power button to turn on the POC-W24C-ULT3.
The user can also long-press the touch buttons
for three seconds to power on the system (please refer to
Figure 3-29: Power Input Connector
3.13 Reset the System
The reset button enables user to reboot the system when the system is turned on. The
reset button location is shown in
Figure 1-4).
on the front panel
Table 1-2). Step 0:
Figure 3-30. Press the reset button to reboot the system.
Page 44
Figure 3-30: Reset Button Location
Page 60
POC-W24C-ULT3 FHD Medical Panel PC
Chapter
4
4 BIOS Setup
Page 45
Page 61
4.1 Introduction
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
NOTE:
Some of the BIOS options may vary throughout the life cycle of the
product and are subject to change without prior notice.
4.1.1 Starting Setup
The UEFI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
POC-W24C-ULT3 FHD Medical Panel PC
1. Press the DEL key as soon as the system is turned on or
2. Press the DEL key when the “Press DEL to enter SETUP” message appears
on the screen. 0.
If the message disappears before the DEL key is pressed, restart the computer and try
again.
4.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press E
keys are shown in the following table.
Key Function
Up arrow Move to the item above
Down arrow Move to the item below
Left arrow Move to the item on the left hand side
SC to quit. Navigation
Page 46
Right arrow Move to the item on the right hand side
+ Increase the numeric value or make changes
Page 62
POC-W24C-ULT3 FHD Medical Panel PC
- Decrease the numeric value or make changes
F1 key General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 key Load previous values.
F3 key Load optimized defaults
F4 key Save changes and Exit BIOS
Esc key Main Menu – Quit and do not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu --
Exit current page and return to Main Menu
Table 4-1: BIOS Navigation Keys
4.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press E
the F1 key again.
4.1.4 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main – Changes the basic system configuration.
Advanced – Changes the advanced system settings.
Chipset – Changes the chipset settings.
Security – Sets User and Supervisor Passwords.
Boot – Changes the system boot configuration.
Save & Exit – Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
SC or
Page 47
Page 63
POC-W24C-ULT3 FHD Medical Panel PC
4.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Main Advanced Chipset Security Boot Save & Exit
BIOS Information
BIOS Vendor American Megatrends
Core Version 5.11
Compliancy UEFI 2.4; PI 1.3
Project Version E422AR10.ROM
Build Date and Time 05/02/2017 14:37:58
Processor Information
Name Skylake
Brand String Intel(R) Core(TM)
i7-6600U CPU @ 2.60GHz
Frequency 2500 MHz
Processor ID 406E3
Stepping D0/K0
Number of Processors 2Core(S)/4Thread(s)
Microcode Revision 7c
GT Info GT2
IGF VBIOS Version 1040
Memory RC Version 1.9.0.0
Total Memory 4096 MB
Memory Frequency 2133 MHz
PCH Information
Name LynxPoint
PCH SKU PCH-LP Mobile(U)
Premium SKU
Stepping 21/C1
LAN PHY Revision N/A
ME FW Version 11.0.0.1202
ME Firmware SKU Corporate SKU
SPI Clock Frequency
D0FR Support Unsupported
Read Status Clock Frequency 17 MHz
Write Status Clock Frequency 17 MHz
Fast Read Status Clock Frequency 17 MHz
System Date [Thu 07/06/2017]
System Time [16:49:37]
Access Level Administrator
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Set the Date. Use Tab to
switch between Date
elements.
----------------------
ÆÅ
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
: Select Screen
Page 48
BIOS Menu 1: Main
Page 64
POC-W24C-ULT3 FHD Medical Panel PC
Î System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
Î System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
4.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING:
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Main Advanced Chipset Security Boot Save & Exit
> Trusted Computing
> ACPI Settings
> F81866 Super IO Configuration
> F81866 H/M Monitor
> RTC Wake Settings
> Serial Port Console Redirection
> CPU Configuration
> SATA Configuration
> USB Configuration
> iEi Feature
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Trusted Computing
Settings
----------------------
ÆÅ
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
: Select Screen
BIOS Menu 2: Advanced
Page 49
Page 65
E
I
POC-W24C-ULT3 FHD Medical Panel PC
4.3.1 Trusted Computing
Use the Trusted Computing menu (BIOS Menu 3) to configure settings related to the
Trusted Computing Group (TCG) Trusted Platform Module (TPM).
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
Configuration
Security Device Support [Enable]
NO Security Device Found
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
nables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
NT1A interface will not
be available.
----------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 3: Trusted Computing
Î Security Device Support [Enable]
Use the Security Device Support option to configure support for the security devices.
Î
Disable
Î
Enable DEFAULT
Security device support is disabled.
Security device support is enabled.
Page 50
Page 66
S
w
POC-W24C-ULT3 FHD Medical Panel PC
4.3.2 ACPI Settings
The ACPI Settings menu (BIOS Menu 4) configures the Advanced Configuration and
Power Interface (ACPI) options.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
ACPI Settings
ACPI Sleep State [S3 (Suspend to RAM)]
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
elect ACPI sleep state
the system will enter
hen the SUSPEND button
is pressed.
----------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 4: ACPI Settings
Î ACPI Sleep State [S3 (Suspend to RAM)]
Use the ACPI Sleep State option to specify the sleep state the system enters when it is
not being used.
Î
S3 (Suspend to
RAM)
DEFAULT
The caches are flushed and the CPU is powered
off. Power to the RAM is maintained. The
computer returns slower to a working state, but
more power is saved.
Page 51
Page 67
S
E
POC-W24C-ULT3 FHD Medical Panel PC
4.3.3 F81866 Super IO Configuration
Use the F81866 Super IO Configuration menu (BIOS Menu 5) to set or change the
configurations for the serial ports.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
F81866 Super IO Configuration
Super IO Chip F81866
> Serial Port 1 Configuration
> Serial Port 2 Configuration
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
et Parameters of Serial
Port 1 (COMA)
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 5: F81866 Super IO Configuration
4.3.3.1 Serial Port n Configuration
Use the Serial Port n Configuration menu (BIOS Menu 6) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
Serial Port 1 Configuration
Serial Port [Enabled]
Device Settings IO=3F8h; IRQ=4
Change Settings [Auto]
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
nable or Disable Serial
Port (COM)
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 6: Serial Port n Configuration Menu
Page 52
Page 68
POC-W24C-ULT3 FHD Medical Panel PC
4.3.3.1.1 Serial Port 1 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Î
Enabled DEFAULT
Î Chan ge Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto DEFAULT
Î
IO=3F8h; IRQ=4
Î
IO=3F8h;
IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12
Î
IO=2F8h;
Disable the serial port
Enable the serial port
The serial port IO port address and interrupt
address are automatically detected.
Serial Port I/O port address is 3F8h and the
interrupt address is IRQ4
Serial Port I/O port address is 3F8h and the
interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,
12
Serial Port I/O port address is 2F8h and the
IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12
Î
IO=3E8h;
IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12
Î
IO=2E8h;
IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12
Î Device Mode [RS232]
Use the Device Mode option to set the Serial Port 1 signaling mode.
interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,
12
Serial Port I/O port address is 3E8h and the
interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,
12
Serial Port I/O port address is 2E8h and the
interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,
12
Page 53
Page 69
POC-W24C-ULT3 FHD Medical Panel PC
Î
RS422
Î
RS232 DEFAULT
Î
RS485
4.3.3.1.2 Serial Port 2 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Î
Enabled DEFAULT
Î Chan ge Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Configure Serial Port 1 as RS-422
Configure Serial Port 1 as RS-232
Configure Serial Port 1 as RS-485
Disable the serial port
Enable the serial port
Î
Auto DEFAULT
Î
IO=2F8h; IRQ=3
Î
IO=3F8h;
IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12
Î
IO=2F8h;
IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12
Î
IO=3E8h;
IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12
Î
IO=2E8h;
IRQ=3, 4, 5, 6, 7,
The serial port IO port address and interrupt
address are automatically detected.
Serial Port I/O port address is 2F8h and the
interrupt address is IRQ3
Serial Port I/O port address is 3F8h and the
interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,
12
Serial Port I/O port address is 2F8h and the
interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,
12
Serial Port I/O port address is 3E8h and the
interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,
12
Serial Port I/O port address is 2E8h and the
interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,
Page 54
9, 10, 11, 12
12
Page 70
POC-W24C-ULT3 FHD Medical Panel PC
4.3.4 F81866 H/W Monitor
The F81866 H/W Monitor menu (BIOS Menu 7) shows the operating temperatures and
voltages.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
PC Health Status
>Smart Fan Mode Configuration
CPU temperature : +51 °C
System temperature : +49 °C
CPU_CORE : +0.880 V
+5V : +4.961 V
+12V : +12.056 V
+DDR : +1.184 V
+3.3V : +3.280 V
+3.3VSB : +3.312 V
+5VSB : +4.896 V
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Smart Fan Mode Select
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 7: F81866 H/W Monitor
Î PC He alth Status
The following system parameters and values are shown. The system parameters that are
monitored are:
Temperature:
o CPU Temperature
o System Temperature
Voltages:
o CPU_CORE
o +5V
o +12V
o +DDR
o +3.3V
o +3.3VSB
o +5VSB
Page 55
Page 71
E
w
POC-W24C-ULT3 FHD Medical Panel PC
4.3.5 RTC Wake Settings
The RTC Wake Settings menu (BIOS Menu 8) configures RTC wake event.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
Wake system with Fixed Time [Disabled]
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
nable or disable System
ake on alarm event. When
enabled, System will
wake on the
dat::hr::min::sec
specified
----------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 8: RTC Wake Settings
Î Wake System with Fixed Time [Disab led]
Use the Wake System with Fixed Time option to specify the time the system should be
roused from a suspended state.
Î
Disabled DEFAULT
The real time clock (RTC) cannot generate a wake
event
Page 56
Page 72
POC-W24C-ULT3 FHD Medical Panel PC
Î
Enabled
If selected, the following appears with values that
can be selected:
*Wake up every day
*Wake up date
*Wake up hour
*Wake up minute
*Wake up second
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
4.3.6 Serial Port Console Redirection
The Serial Port Console Redirection menu (BIOS Menu 9) allows the console
redirection options to be configured. Console redirection allows users to maintain a
system remotely by re-directing keyboard input and text output through the serial port.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
COM1
Console Redirection [Disabled]
> Console Redirection Settings
COM2
Console Redirection [Disabled]
> Console Redirection Settings
Legacy Console Redirection
> Legacy Console Redirection Settings
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Console Redirection
Enable or Disable.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 9: Serial Port Console Redirection
Page 57
Page 73
E
c
Î Cons ole Redirection [Disabled]
Use Console Redirection option to enable or disable the console redirection function.
POC-W24C-ULT3 FHD Medical Panel PC
Î
Disabled DEFAULT
Î
Enabled
Disabled the console redirection function
Enabled the console redirection function
4.3.6.1 Console Redirection Settings
Use the Console Redirection Settings menu (6BIOS Menu 10) to configure console
redirection settings of the specified serial port. This menu appears only when the Console
Redirection option is enabled.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Advanced
COM1
Console Redirection Settings
Terminal Type [ANSI]
Bits per second [115200]
Data Bits [8]
Parity [None]
Stop Bits [1]
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
mulation: ANSI: Extended
ASCII char set. VT100:
ASCII char set. VT100+:
Extends VT100 to support
olor, function keys, etc.
VT-UTF8: Uses UTF8
encoding to map Unicode
chars onto 1 or more bytes.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 10: Console Redirection Settings
Î Terminal Type [ANSI]
Use the Terminal Type option to specify the remote terminal type.
Î
VT100
Î
VT100+
Page 58
The target terminal type is VT100
The target terminal type is VT100+
Page 74
POC-W24C-ULT3 FHD Medical Panel PC
Î
VT-UTF8
Î
ANSI DEFAULT
Î Bits per second [1 15200]
Use the Bits per second option to specify the serial port transmission speed. The speed
must match the other side. Long or noisy lines may require lower speeds.
Î
9600
Î
19200
Î
57600
Î
115200 DEFAULT
Î Data Bits [8]
Use the Data Bits option to specify the number of data bits.
The target terminal type is VT-UTF8
The target terminal type is ANSI
Sets the serial port transmission speed at 9600.
Sets the serial port transmission speed at 19200.
Sets the serial port transmission speed at 57600.
Sets the serial port transmission speed at 115200.
Î
7
Î
8 DEFAULT
Î Parity [None]
Use the Parity option to specify the parity bit that can be sent with the data bits for
detecting the transmission errors.
Î
None DEFAULT
Î
Even
Î
Odd
Î
Mark
Î
Space
Sets the data bits at 7.
Sets the data bits at 8.
No parity bit is sent with the data bits.
The parity bit is 0 if the number of ones in the data
bits is even.
The parity bit is 0 if the number of ones in the data
bits is odd.
The parity bit is always 1. This option does not
provide error detection.
The parity bit is always 0. This option does not
provide error detection.
Page 59
Page 75
Î Stop Bits [1]
Use the Stop Bits option to specify the number of stop bits used to indicate the end of a
serial data packet. Communication with slow devices may require more than 1 stop bit.
POC-W24C-ULT3 FHD Medical Panel PC
Î
1 DEFAULT
Î
2
Sets the number of stop bits at 1.
Sets the number of stop bits at 2.
4.3.6.2 Legacy Console Redirection Settings
The Legacy Console Redirection Settings menu (6BIOS Menu 11) allows the legacy
console redirection options to be configured.
Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc.
Advanced
Legacy Serial Redirection Port [COM1]
Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.
Select a COM port to
display redirection of
Legacy OS and Legacy
OPROM Messages
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 11: Legacy Console Redirection Settings
Î Legacy Serial Redirection Port [COM1]
Use the Legacy Serial Redirection Port option to specify a COM port to display
redirection of legacy OS and legacy OPROM messages. The options include:
EFAULT
Page 60
COM1 D
COM2
COM3 (Pci Bus0, Dev0, Func0) (Disabled)
Page 76
T
D
POC-W24C-ULT3 FHD Medical Panel PC
4.3.7 CPU Configuration
Use the CPU Configuration (BIOS Menu 12) to view detailed CPU specifications and
configure the CPU.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
CPU Configuration
Intel(R) Core(TM) i7-6600U CPU @ 2.60GHz
CPU Signature 406E3
Microcode Patch 7C
Max CPU Speed 2600 MHz
Min CPU Speed 400 MHz
CPU Speed 2500 MHz
Processor Cores 2
Hyper Threading Technology Supported
Intel VT-x Technology Supported
Intel SMX Technology Supported
64-bit Supported
EIST Technology Supported
L1 Data Cache 32 kB x 2
L1 Code Cache 32 kB x 2
L2 Cache 256 kB x 2
L3 Cache 4 MB
Hyper-threading [Enabled]
Active Processor Cores [All]
Intel Virtualization Technology [Disabled]
Intel(R) SpeedStep(tm) [Enabled]
CPU C states [Disabled]
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Enable for Windows XP and
Linux (OS optimized for
Hyper-Threading
echnology) and Disabled
for other OS (OS not
optimized for
Hyper-Threading
Technology). When
isabled only one thread
per enabled core is
enabled.
----------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 12: CPU Configuration
The CPU Configuration menu lists the following CPU details:
Processor Type: Lists the brand name of the CPU being used
CPU Signature: Lists the CPU signature value.
Microcode Patch: Lists the microcode patch being used.
Max CPU Speed: Lists the maximum CPU processing speed.
Min CPU Speed: Lists the minimum CPU processing speed.
CPU Speed: Lists the CPU processing speed.
Processor Cores: Lists the number of the processor core
Hyper Threading Technology: Indicates if Intel HT Technology is supported by
the CPU.
Page 61
Page 77
Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the
CPU.
Intel SMX Technology: Indicates if Intel SMX Technology is supported by the
CPU.
64-bit: Indicates if 64-bit OS is supported by the CPU.
EIST Technology: Indicates if EIST Technology is supported by the CPU.
L1 Data Cache: Lists the amount of data storage space on the L1 cache.
L1 Code Cache: Lists the amount of code storage space on the L1 cache.
L2 Cache: Lists the amount of storage space on the L2 cache.
L3 Cache: Lists the amount of storage space on the L3 cache.
Î Hyper-threading [Enabled]
Use the Hyper-threading option to enable or disable the Intel® Hyper-Threading
Technology.
POC-W24C-ULT3 FHD Medical Panel PC
Î
Disabled
Î
Enabled DEFAULT
Î Active Processor Cores [All]
Use the Active Processor Cores BIOS option to enable numbers of cores in the
processor package.
Î
All DEFAULT
Î
1
Î Intel Virtualization Technology [Disabled]
Use the Intel Virtualization Technology option to enable or disable virtualization on the
system. When combined with third party software, Intel® Virtualization technology allows
several OSs to run on the same system at the same time.
Disable Intel® Hyper-Threading Technology
Enable Intel® Hyper-Threading Technology
Enable all cores in the processor package.
Enable one core in the processor package.
Page 62
Î
Disabled DEFAULT
Î
Enabled
Disables Intel Virtualization Technology.
Enables Intel Virtualization Technology.
Page 78
POC-W24C-ULT3 FHD Medical Panel PC
Î Intel® SpeedStep(tm) [Enabled]
®
Use the Intel
Technology.
Î
Disabled
Î
Enabled DEFAULT
Î CPU C State [Disabled]
Use the CPU C State option to enable or disable CPU C state.
Î
Disabled DEFAULT
Î
Enabled
SpeedStep™ option to enable or disable the Intel
Disables the Intel
Enables the Intel
Disables CPU C state.
Enables CPU C state.
®
®
SpeedStep Technology.
SpeedStep Technology.
®
SpeedStep
4.3.8 SATA Configuration
Use the SATA Configuration menu (BIOS Menu 13) to change and/or set the
configuration of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
SATA Controller(s) [Enabled]
SATA Mode Selection [AHCI]
SATA1 Empty
Hot Plug [Disabled]
SATA2 Empty
Hot Plug [Disabled]
mATA(M_PCIE1) Empty
Hot Plug [Disabled]
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
BIOS Menu 13: SATA Configuration
Enable/Disable SATA
Device.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Page 63
Page 79
Î SATA Controller(s) [Enabled]
Use the SATA Controller(s) option to configure the SATA controller(s).
POC-W24C-ULT3 FHD Medical Panel PC
Î
Enabled DEFAULT
Î
Disabled
Î SATA Mode Selection [AHCI]
Use the SATA Mode Selection option to determine how SATA devices operate.
Î
AHCI DEFAULT
Î Hot Plug [Disabled ]
Use the Hot Plug option to enable or disable the SATA device hot plug.
Î
Disabled DEFAULT
Î
Enabled
Enable the on-board SATA controller(s).
Disable the on-board SATA controller(s).
Configures SATA devices as AHCI device.
Disables the SATA device hot plug.
Enables the SATA device hot plug
Page 64
Page 80
d
POC-W24C-ULT3 FHD Medical Panel PC
4.3.9 USB Configuration
Use the USB Configuration menu (BIOS Menu 14) to read USB configuration
information and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
USB Configuration
USB Controllers:
1 XHCI
USB Devices:
1 Keyboard, 1 Mouse, 1 Point, 2 Hubs
Legacy USB Support [Enabled]
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Enables Legacy USB
support. AUTO option
isables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 14: USB Configuration
Î USB Dev i ces
The USB Devices Enabled field lists the USB devices that are enabled on the system
Î Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.
Page 65
Page 81
c
s
POC-W24C-ULT3 FHD Medical Panel PC
Î
Enabled DEFAULT
Î
Disabled
Î
Auto
Legacy USB support enabled
Legacy USB support disabled
Legacy USB support disabled if no USB devices are
connected
4.3.10 IEI Feature
Use the IEI Feature menu (BIOS Menu 15) to configure One Key Recovery function.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Advanced
iEi Feature
Auto Recovery Function [Disabled]
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Auto Recovery Function
Reboot and recover
system automatically
within 10 min, when OS
rashes. Please install
Auto Recovery API
ervice before enabling
this funciton.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 15: IEI Feature
Î Auto Re covery Function [Disabled]
Use the Auto Recovery Function BIOS option to enable or disable the auto recovery
function of the IEI One Key Recovery.
Î
Disabled DEFAULT
Î
Enabled
Auto recovery function disabled
Auto recovery function enabled
Page 66
Page 82
POC-W24C-ULT3 FHD Medical Panel PC
4.4 Chipset
Use the Chipset menu (BIOS Menu 16) to configure the system chipset.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Main Advanced Chipset Security Boot Save & Exit
> System Agent (SA) Configuration
> PCH-IO Configuration
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
System Agent (SA)
Parameters
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 16: Chipset
4.4.1 System Agent (SA) Configuration
Use the System Agent (SA) Configuration menu (BIOS Menu 17) to configure the
System Agent (SA) parameters.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Chipset
VT-d [Disabled]
> Graphics Configuration
> Memory Configuration
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
VT-d capability
---------------------
ÆÅ
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
: Select Screen
BIOS Menu 17: System Agent (SA) Configuration
Page 67
Page 83
G
Î VT-d [Disabled]
Use the VT-d option to enable or disable VT-d support.
POC-W24C-ULT3 FHD Medical Panel PC
Î
Disabled DEFAULT
Î
Enabled
Disable VT-d support.
Enable VT-d support.
4.4.1.1 Graphics Configuration
Use the Graphics Configuration menu (6BIOS Menu 18) to configure the graphics
settings.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Chipset
Graphics Configuration
Primary Display [Auto]
Internal Graphics [Enabled]
DVMT Pre-Allocated [256M]
DVMT Total Gfx Mem [MAX]
> LCD Control
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Select which of IGFX/PCIE
Primary Display.
---------------------
ÆÅ
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
raphics device should be
: Select Screen
BIOS Menu 18: Graphics Configuration
Î Primary Display [Auto]
Use the Primary Display option to select the graphics controller used as the primary boot
device. Configuration options are listed below:
Auto D
IGFX
PCIE
Page 68
EFAULT
Page 84
POC-W24C-ULT3 FHD Medical Panel PC
Î Internal Gr aphics [Enabled]
Use the Internal Graphics option to enable or disable the internal graphics device.
Î
Auto
Î
Disabled
Î
Enabled DEFAULT
Î DVMT Pre-Allocated [256M]
Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the
integrated graphics processor when the system boots. The system memory allocated can
then only be used as graphics memory, and is no longer available to applications or the
operating system. Configuration options are listed below:
The internal graphics device is automatically detected
and enabled.
Disable the internal graphics device.
Enable the internal graphics device. The following
options/submenu appear with values that can be
selected:
DVMT Pre-Allocated
DVMT Total Gfx Mem
LCD Control
32M
64M
128M
256M D
512M
Î DVMT Total Gfx Mem [MAX]
Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used
by the internal graphic device. The following options are available:
128M
256M
MAX D
EFAULT
EFAULT
Page 69
Page 85
S
w
d
b
POC-W24C-ULT3 FHD Medical Panel PC
4.4.1.1.1 LCD Control
Use the LCD Control submenu (BIOS Menu 19) to select a display device which will be
activated during POST.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Chipset
LCD Control
Primary IGFX Boot Display [VBIOS Default]
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
elect the Video Device
hich will be activated
uring POST. This has no
effect if external
graphics present.
Secondary boot display
selection will appear
ased on your selection.
VGA modes will be
supported only on
primary display.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 19: LCD Control
Î Primary IGFX Boot Display [VBIOS Default]
Use the Primary IGFX Boot Display option to select the display device used by the
system when it boots.
Page 70
VBIOS Default
HDMI
LVDS
DEFAULT
Page 86
S
POC-W24C-ULT3 FHD Medical Panel PC
4.4.1.2 Memory Configuration
Use the Memory Configuration submenu (6BIOS Menu 20) to display the memory
information.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Chipset
Memory Information
Total Memory 4096 MB
DIMM1 Not Present
DIMM2 4096 MB
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 20: Memory Configuration
4.4.2 PCH-IO Configuration
Use the PCH-IO Configuration menu (BIOS Menu 21) to configure the PCH-IO chipset.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Chipset
Auto Power Button Status [Disable (ATX)]
> PCI Express Configuration
> HD Audio Configuration
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
power is re-applied after
a power failure.
---------------------
ÆÅ
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
elect AC power state when
: Select Screen
BIOS Menu 21: PCH-IO Configuration
Page 71
Page 87
POC-W24C-ULT3 FHD Medical Panel PC
4.4.2.1 PCI Express Configuration
Use the PCI Express Configuration submenu (BIOS Menu 22) to configure the PCI
Express slots.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Chipset
PCI Express Configuration
> M_PCIE1
> M2_CN1
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
M_PCIE1 Settings.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 22: PCI Express Configuration
The M_PCIE1 and M2_CN1 submenus both contain the following options:
Î PCIe Speed [Auto]
Use the PCIe Speed option to configure the PCIe interface speed.
Auto D
Gen 1
Gen 2
Gen 3
Î De tect Non-Compliance Device [Disabled]
Use the Detect Non-Compliance Device option to enable or disable detecting if a
non-compliance PCI Express device is connected to the PCI Express slot.
EFAULT
Page 72
Page 88
C
POC-W24C-ULT3 FHD Medical Panel PC
Î
Disabled DEFAULT
Î
Enabled
Disables to detect if a non-compliance PCI
Express device is connected to the PCI Express
slot.
Enables to detect if a non-compliance PCI Express
device is connected to the PCI Express slot.
4.4.2.2 HD Audio Configuration
Use the HD Audio Configuration submenu (BIOS Menu 23) to configure the High
Definition Audio codec.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Chipset
HD Audio Configuration
HD Audio [Enabled]
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
ontrol Detection of the
HD-Audio device.
Disable = HDA will be
unconditionally
disabled
Enabled = HDA will be
unconditionally
enabled.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 23: HD Audio Configuration
Î HD Audio [Enabled]
Use the HD Audio BIOS option to enable or disable the High Definition Audio controller.
Î
Disabled
Î
Enabled DEFAULT
The High Definition Audio controller is disabled.
The High Definition Audio controller is enabled.
Page 73
Page 89
POC-W24C-ULT3 FHD Medical Panel PC
4.5 Security
Use the Security menu (BIOS Menu 24) to set system and user passwords.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Main Advanced Chipset Security Boot Save & Exit
Password Description
If ONLY the Administrator’s password is set,
then this only limits access to Setup and is
only asked for when entering Setup.
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password must be
In the following range:
Maximum length 3
Minimum length 20
Administrator Password
User Password
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Set Administrator
Password
---------------------
ÆÅ
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
: Select Screen
BIOS Menu 24: Security
Î Administr ator Password
Use the Administrator Password field to set or change an administrator password.
Î Use r Password
Use the User Password field to set or change a user password.
Page 74
Page 90
POC-W24C-ULT3 FHD Medical Panel PC
4.6 Boot
Use the Boot menu (BIOS Menu 25) to configure system boot options.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Main Advanced Chipset Security Boot Save & Exit
Boot Configuration
Bootup NumLock State [On]
Quiet Boot [Enabled]
UEFI Boot [Disabled]
Launch PXE OpROM [Disabled]
Option ROM Messages [Force BIOS]
Boot Option Priorities
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Select the keyboard
NumLock state
---------------------
ÆÅ
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
: Select Screen
BIOS Menu 25: Boot
Î Boo tup NumLock State [On]
Use the Bootup NumLock State BIOS option to specify if the number lock setting must
be modified during boot up.
Î
On DEFAULT
Î
Off
Allows the Number Lock on the keyboard to be
enabled automatically when the computer system
boots up. This allows the immediate use of the
10-key numeric keypad located on the right side of
the keyboard. To confirm this, the Number Lock LED
light on the keyboard is lit.
Does not enable the keyboard Number Lock
automatically. To use the 10-keys on the keyboard,
press the Number Lock key located on the upper
left-hand corner of the 10-key pad. The Number
Lock LED on the keyboard lights up when the
Number Lock is engaged.
Page 75
Page 91
Î Quiet Boot [Enabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
POC-W24C-ULT3 FHD Medical Panel PC
Î
Disabled
Î
Enabled DEFAULT
Î UEFI Boot [Disabled]
Use the UEFI Boot BIOS option to enable or disable UEFI boot.
Î
Disabled DEFAULT
Î
Enabled
Î Launch PXE OpROM [Disabled]
Use the Launch PXE OpROM option to enable or disable boot option for legacy network
devices.
Î
Disabled DEFAULT
Normal POST messages displayed
OEM Logo displayed instead of POST messages
Disable UEFI boot.
Enable UEFI boot if the 1
HDD.
Ignore all PXE Option ROMs
st
boot device is a GPT
Î
Enabled
Î Option ROM Messages [F orce BIOS]
Use the Option ROM Messages option to set the Option ROM display mode.
Î
Î
Force
BIOS
Keep
Current
DEFAULT
Load PXE Option ROMs
Sets display mode to force BIOS.
Sets display mode to current.
Page 76
Page 92
POC-W24C-ULT3 FHD Medical Panel PC
4.7 Save & Exit
Use the Save & Exit menu (BIOS Menu 26) to load default BIOS values, optimal failsafe
values and to save configuration changes.
Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.
Main Advanced Chipset Security Boot Save & Exit
Save Changes and Reset
Discard Changes and Reset
Restore Defaults
Save as User Defaults
Restore User Defaults
Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.
Reset the system after
saving the changes.
---------------------
ÆÅ
: Select Screen
↑ ↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
BIOS Menu 26: Save & Exit
Î Save Changes and Reset
Use the Save Changes and Reset option to save the changes made to the BIOS options
and reset the system.
Î Disca rd Changes and Reset
Use the Discard Changes and Reset option to exit the system without saving the
changes made to the BIOS configuration setup program.
Î Res tore Defaults
Use the Restore Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F3 key can be used for this operation.
Page 77
Page 93
Î Save as User Defaults
Use the Save as User Defaults option to save the changes done so far as user defaults.
Î Restore User Defaults
Use the Restore User Defaults option to restore the user defaults to all the setup options.
POC-W24C-ULT3 FHD Medical Panel PC
Page 78
Page 94
POC-W24C-ULT3 FHD Medical Panel PC
5 Driver Installation
Chapter
5
Page 79
Page 95
5.1 Available Software Drivers
NOTE:
The contents of the driver folder may vary throughout the life cycle of
the product and is subject to change without prior notice. Visit the IEI
website or contact technical support for the latest updates.
All the drivers for the POC-W24C-ULT3 are on the utility CD that came with the system.
To install the drivers, please follow the steps below.
Step 1: Insert the CD into a CD drive connected to the system.
POC-W24C-ULT3 FHD Medical Panel PC
Step 2: The driver main menu with a list of available drivers appears (
Figure 5-1).
Page 80
Figure 5-1: Available Drivers
Step 3: Install all of the necessary drivers in this menu. Step 0:
Page 96
POC-W24C-ULT3 FHD Medical Panel PC
5.2 Intel® Chipset Driver
To install the chipset driver, please follow the steps below.
Step 1: Select Chipset from the list of the driver CD.
Step 2: Double click the setup file in the folder. The Intel® Chipset Device Software
installation wizard appears.
Figure 5-2: Intel® Chipset Device Software Installation Wizard
Step 3: Follow the step-by-step instruction of the installation wizard to install the driver.
Step 0:
Page 81
Page 97
5.3 Intel® Graphics Driver
To install the graphics driver, please follow the steps below.
Step 1: Select VGA from the list of the driver CD. Locate the driver setup file for the
corresponding operating system.
Step 2: Double click the setup file in the folder. The Intel® Graphics Driver installation
POC-W24C-ULT3 FHD Medical Panel PC
wizard appears (
Figure 5-3: Intel® Graphics Driver Installation Wizard
476Figure 5-3).
Page 82
Step 3: Follow the step-by-step instruction of the installation wizard to install the
graphics driver. Step 0:
Page 98
POC-W24C-ULT3 FHD Medical Panel PC
5.4 Audio Driver
To install the driver for the speaker and the microphone, please follow the steps below.
Step 1: Select Audio from the list of the driver CD.
Step 2: Double click the setup file in the folder. The InstallShield Wizard screen
appears (
Figure 5-4: Realtek HD Audio Driver InstallShield Wizard
6Figure 5-4).
Step 3: Follow the step-by-step instruction of the installation wizard to install the HD
Audio driver. Step 0:
Page 83
Page 99
5.5 LAN Driver
To install the LAN driver, please follow the steps below.
Step 1: Select LAN from the list of the driver CD. Locate the driver setup file for the
corresponding operating system.
Step 2: Double click the setup file in the folder. The Install Wizard screen appears
6Figure 5-4).
(
POC-W24C-ULT3 FHD Medical Panel PC
Page 84
Figure 5-5: LAN Driver Installation Wizard
Step 3: Follow the step-by-step instruction of the installation wizard to install the Intel®
Network Connection driver. Step 0:
Page 100
POC-W24C-ULT3 FHD Medical Panel PC
5.6 Intel® Management Engine
To install the Intel® Management Engine Components, please follow the steps below.
Step 1: Select ME from the list of the driver CD. Locate the driver setup file.
Step 2: Double click the setup file. The installation wizard window appears (
476Figure 5-3).
Figure 5-6: Intel® ME Components Installation Wizard
Step 3: Follow the step-by-step instruction of the installation wizard to install the Intel®
Management Engine Components. Step 0:
Page 85
Loading...