Page 1
Medical Panel PC with 6th Gen. Intel® Core™ / Celeron® CPU ,
4 GB DDR4 RAM, Wi-Fi 802.11a/b/g/n/ac, P-CAP Touchscreen,
Three Battery Bays, 5-Megapixel Camera and Microphone
POCm-W22C-ULT3
POCm-W24C-ULT3
Quick Installation Guide
Version 1.01
©2018 Copyright by IEI Integration Corp.
All rights reserved.
Page 2
1
Revision
Date
Version
Changes
September 11, 2018 1.01 Minor update
August 28, 2018 1.00 Initial release
Intended Use
The POCm-W22/24C-ULT3 medi cal panel PC is intended to be used to display
general purpose medical im ages. The device shall not be used for diagnosis
purpose or life supporting system.
Equipment connected to analog or digital interfaces must comply with the respective
IEC Standards (e.g. IEC 60950 for data processing equipment and IEC 60601-1 for
medical equipment). Furthermore all configurations shall comply with the current
version of the standard for S Y STEMS IEC 60601-1-1. Everybod y who connects
additional equipment to the signal input part or signal output part configure a
medical system, and is ther efore responsible that the system complies with current
version of the requirement s of the system standard IEC 60601-1-1. If in doubt,
consult the technical service department or your local repr esentative.
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages shou ld be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any
directions or instructions contained therein can help avoid making
mistakes.
OPERATING INSTRUCTION
Follow operating instructions or consult instructi ons for use.
IEC 60417-5009: Stand-by
IEC 60417-5031: Direct current
Page 3
2
Overview
The POCm-W22/24C-ULT3 is a 6th generation Intel® Core™ i5-6300U
processor powered medical-grade panel PC with a rich variety of functions
and peripherals. All POCm-W22/24C-ULT3 models are designed for easy
and simplified integration into point-of-care (POC) applications. The system
comes with 4 GB of preinstalled DDR4 memory and supports a maximum
of 32 GB ensuring smooth data throughputs with reduced bottlenecks and
fast system access.
Two RS-232/422/485 serial ports, four USB 3.0 ports and two USB 2. 0
ports provide simplified connectivit y to a variety of external peripheral
devices. Wi-Fi 802.11a/b/g/n/ ac high speed wireless and two RJ-45 GbE
connectors allow for smooth connection of the system to an ext ernal LAN.
Three hot-swappable battery bays all ow installation of three batterie s to
provide continuous power for 8~16 hou rs.
Page 4
3
Front Panel
Bottom Panel
Page 5
4
Side Panel
Rear Panel
Page 6
5
System Specifications
POCm-W22C-ULT3
POCm-W24C-ULT3
LCD and Touchscreen
LCD Size 21.5" (16:9) 23.8" (16:9)
Max. Resolution
1920 (W) x 1080 (H)
1920 (W) x 1080 (H)
Brightness (cd/m2)
250
250
Contrast Ratio
1000:1
1000:1
LCD Color
16.7M (RGB 6-bit)
16.7M (RGB 6-bit + Hi-FRC)
Pixel Pitch (mm)
0.24825 (H) x 0. 24825 (V)
0.2745 (H) x 0. 2745 (V)
Viewing Angle (H-V)
170°/160°
178°/178°
Backlight MTBF
30,000 hrs (LED backlight)
30,000 hrs (LED backlight)
Touchscreen
Projected capacitive type wi th USB interface
Multi-touch
10-point touch
Touch Controller
EETI
Surface Hardness
6H
System
CPU
Intel® Celeron® 3855U / Intel® Core™ i5-6300U /
Intel® Core™ i7-6600U
Memory
Two 260-pin 2133/1866 MHz dual-channel non-ECC
unbuffered DDR4 SO-DIMMs sup ported (system max.
32 GB)
Preinstalled with 4 GB memory
GbE Controller
LAN1: Intel I211 Ethernet controller
LAN2: Intel® I219 Ethernet controller
I/O Ports
1 x DC input jack
2 x HDMI output connector
2 x GbE LAN (RJ-45 connector)
2 x RS-232/422/485 serial port (DB-9 connector)
4 x USB 3.0 connectors
2 x USB 2.0 connectors (side panel)
1 x Audio out (side panel)
1 x Mic-in (side panel)
1 x Digital microphone
Storage
One 2.5” SATA 6Gb/s HDD bay
Audio
Two 3 W speakers
Webcam & Microphone
5-megapixel CMOS front-facing camera wi th auto focus and
digital microphone
Expansion Interface
2 x M.2 M-key 2242/2260/2280 slot (PCIe + SATA) with
RAID
1 x M.2 A-/E-key 2242 slot (PCIe + USB)
1 x Full-size/Half-size PCIe Min i (PCIe + USB)
Page 7
6
TPM
TPM 2.0 (optional)
Other Features
1 x Power on/off
1 x Brightness up
Function Keys
1 x Brightness down
1 x Volume up
1 x Volume down
1 x Touch lock (clean mode) or LCD on/off
LED Indicators
3 x Battery indicator
1 x Power indicator
Cooling Method
Fanless
Connectivity
Wi-Fi and Bluetooth
802.11a/b/g/n/ac dual band, Bluetooth v4.2
(M.2 2230 module, Intel® 8265)
LAN
Two GbE LAN connectors
Physical
Construction Material
PC+ABS plastic with anti-bacterial material
Mounting
Wall and stand mounting
VESA 75 mm x 75 mm or 100 mm x 100 mm
Dimensions (W x H x D)
543 x 350 x 71 (mm)
594.6 x 379.6 x 71 (mm)
Net Weight
7.07 kg
8.18 kg
Environment
Storage/Transportation
Temperature
-20ºC ~ 60ºC
Humidity
10% ~ 90% (non-condensing)
Pressure
700 hPa ~ 1060 hPa
Operating
Temperature
0ºC ~ 40ºC
Humidity
10% ~ 90% (non-condensing)
Pressure
700 hPa ~ 1060 hPa
Vibration
1G
Shock
Operating Shock: 5G peak acceleration (11ms duration)
Non-Operating Shock: 10G peak acceleration (11ms
duration)
IP Level
IP 65 compliant front panel
Power
Power Input
19 V DC
Power Adapter
150 W FSP FSP150M-ABA medical-grade power adapter
(P/N: 63040-010150-400-RS)
Input: 100 V AC ~ 240 V AC, 50 Hz ~ 60 Hz, 2A ~ 0.85A
Output: 19 V 7.89 A
Battery
3 x Hot-swappable battery bay
Page 8
7
Installation Precautions
When installing the medical panel PC, please follow the precautions liste d
below:
Manufacturer authorization: Do not modify this equipment
without authorization of manufacturer.
Certified Engineers: Only certified engineers sho uld install and
modify the hardware settings.
Power turned off: When installing the medical panel PC, make
sure the power is off. Failing to turn off the power may cause
severe injury to the body and/or damage to the system.
Anti-static Discharge: If a user open the rear pa nel of the m edical
panel PC, to configure the jumpers or plug in added peripheral
devices, ground themselves first and wear an anti-static wristband.
WARNING:
Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent t ype recommended by the manufacturer.
Disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an expl osion or the leakage of
flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in
an explosion or the leakage of flamm able liquid or gas.
Page 9
8
Mounting the System
WARNING:
Use suitable mounting apparatu s and be sure to secure the screws of
the mounting apparatus tightly to avoid risk of injury.
NOTE:
When mounting the POCm-W22/24C-ULT3 flat panel PC, it is bet ter to
have more than one person to help with the installation to make sure the
POCm-W22/24C-ULT3 does not fall down and get dam aged.
The POCm-W22/24C-ULT3 is VESA (Video Electronics Standards
Association) compliant and can be m ounted on a mounting device wit h a 75
mm or 100 mm interface pad. The POCm-W22/24C-ULT3 VESA mount
retention screw holes are shown below. Refer to the installation guide that
came with the mounting device to mount the POCm-W22/24C-ULT3.
Page 10
9
Powering On the System
WARNING:
To avoid risk of electric shock, this equipment must only be connected to
supply mains with protective earth.
CAUTION:
The FSP FSP150M-ABA power adapter came with the
POCm-W22/24C-ULT3 is a forming part of the medic al device.
Step 1: Connect the power cord to the powe r adapter. Connect the other
end of the power cord to a power source.
Step 2: Connect the power adapter to the power connector of the
POCm-W22/24C-ULT3.
Step 3: Locate the power button on the right panel.
Step 4: Short press the power button to t urn on the POCm-W22/24C-ULT3.
Shutdown Procedure
Turn off the power and disconnect the power cord.
To prevent the risk of electric shock, make sure power cord is
unplugged from wall socket. To fully disengage the power to the unit,
please disconnect the power cord from the AC outlet. Refer servicin g to
qualified service personnel. The AC out l et shall be readily available and
accessible.
Page 11
10
Troubleshooting
If the following situations happen, contact your distributor, sales
representatives or IEI customer serv ice center for technical support.
The HDD is installed correctly, but the POCm-W22/24C-ULT3 is
unable to boot with AC power input after pressing the power button.
Unable to shut down the POCm-W22/24C-ULT3 normally
Please have the following informatio n prepared prior to reporting the
abnormal situations:
Product name and S/N
OS, BIOS version and applications
A complete descriptio n of the ab normal sit uation (with photos or vid eo
if available)
System Maintenance
If the components of the POCm-W22/24C-ULT3 fail they must be replaced.
Please contact the system reseller o r vendor to purchase the replacement
parts.
Maintenance and Cleaning
Prior to cleaning any part or component of the POCm-W22/24C-ULT3,
please read the details below.
To clean the POCm-W22/24C-ULT3,
o remove dirt with a lightly moistened cloth. Then wipe the external
chassis with a soft dry cloth.
o use 75% ethanol alcohol to clean the ex ternal chassis.
Cleaning frequency: follow the cleaning method guidel i nes of the
hospital.
Except for the LCD panel, never spray or squirt liquids directly onto
any other components.
The interior of the POCm-W22/24C-ULT3 does not require cle aning.
Keep fluids away from the POCm-W22/24C-ULT3 interior.
Never drop any objects or liquids through the opening s of the
POCm-W22/24C-ULT3.
Page 12
11
Accessories
The medical panel PC is shipped with t he following components:
Quantity Item Image
1
POCm-W22/24C-ULT3
medical panel
PC
1
Power cord
(P/N: 32702-000200-100-RS)
1
150 W FSP FSP150M-ABA
medical-grade power adapter
(P/N: 63040-010150-400-RS)
4
Round-head screw (M3*3) for HDD
installation
(P/N: 44003-030032-RS)
1 Quick Installation Guide
Optional Items
The following components may be separately purchased:
Item and Part Number Image
Li-ion battery pack, 7800 mAh
(P/N: 31603-000069-RS)
Cable cover
(P/N: 43106-0272Q7-00-RS)
20-pin Infineon TPM 2.0 module, software
management tool, firmware v5.5
(P/N: TPM-IN02-R20)
Page 13
12
DECLARATION OF CONFORMITY
This equipment is in conformit y with the following EU directives:
EMC Directive (2004/108/EC, 2014/30/EU)
Low-Voltage Directive (2006/95/EC, 2014/35/EU)
RoHS II Directive (2011/65/EU, 2015/863/EU)
Medical Device Directive 93/42/EE C: EN 60601-1
If the user modifies and/or install other dev ices in the equipment, the CE
conformity declaration may no l onger apply.
If this equipment has telecommunications functionality, it also complies
with the requirements of the Radio E quipment Directive 2014/53/EU.
IEI Integration Corp declares that t his equipme nt i s in complia nce wit h the
essential requirements and ot her relevant provisions of Directive
2014/53/EU.
FCC WARNING
This equipment complies with part 18 of the FCC Rules.
This equipment generates, use s and can radiate radio frequency energy
and, if not installed and used in acco rdance with the instructions, m ay
cause harmful interference to radio co mmunicat ions. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to corre ct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the e quipment and receiver.
Connect the equipment into an outlet on a circuit dif ferent from t hat
to which the receiver is connected.
Page 14
13
ROHS STATEMENT
The label on the product indicates this product conforms to European
(EU) Restriction of Hazardous Sub st ances (RoHS) that set maximum
concentration limits on hazardous materials used in electrical and
electronic equipment.
CHINA RO H S
The label on the product indicates the estimated “Environmentally
Friendly Use Period” (EFUP). Thi s is an estimate of the number of years
that these substances would “not l eak out or undergo abrupt change.”
This product may contain repla ceable sub-assemblies/components which
have a shorter EFUP such as batteries a nd lamps. These components will
be separately marked.
Page 15
14
Safety Precautions
WARNING:
The precautions outlined below should be strictly followed. Failure to
follow these precautions may result i n permanent damage to the
POCm-W22/24C-ULT3.
General Safety Precautions
Please ensure the following safety precautions are adhered to at all times.
To prevent the risk of electric shock, make sure power cord is
unplugged from wall socket. To fully disengage the power to the unit,
please disconnect the power cord from the ac outlet. Refer servicing
to qualified service personnel. The AC outlet shall be readily available
and accessible.
Users must not allow SIP/SOPs and the patient to come int o contact
at the same time.
Grounding reliability can only be achieved when the equipment is
connected to an equivalent receptacle marked “Hospital Only” or
“Hospital Grade”.
Follow the electrostatic precautions outlined below whenever the
POCm-W22/24C-ULT3 is opened.
Make sure the power is turned off and the po wer cord is di sconnect ed
whenever the POCm-W22/24C-ULT3 is being installed, m oved or
modified.
Do not apply voltage levels that exceed the specified voltage range.
Doing so may cause fire and/or an electri cal shock. Use a powe r cord
that matches the voltage of the power outlet, which has been
approved and complies with the safety standard of your particular
country.
Electric shocks can occur if the POCm-W22/24C-ULT3 chassis is
opened when the POCm-W22/24C-ULT3 is running. To avoid risk of
electric shock, this equipment must onl y be connected to a supply
mains with protective earth.
DO NOT LEA VE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4°F) OR ABOVE 60° C (140° F). IT MAY DAMAGE
THE EQUIPMENT.
Do not drop or insert any objects into the ventilation openi ngs of the
POCm-W22/24C-ULT3.
If considerable amounts of dust, water, or fluids enter the
POCm-W22/24C-ULT3, turn off the power supply immediat ely, unplug
the power cord, and contact the POCm-W22/24C-ULT3 vendor .
Page 16
15
DO NOT:
o Drop the POCm-W22/24C-ULT3 against a hard surface.
o Strike or exert excessive force onto the LCD panel.
o Touch any of the LCD panels with a sharp object
o In a site where the ambient temperature exceeds the rated
temperature
Product Disposal
CAUTION:
Risk of explosion if battery is replaced by an incorrect ty pe. Only certified
engineers should replace the on-board battery.
Dispose of used batteries acc ordi ng to i n stru ction s a nd l ocal r egul a tions.
Outside the European Union - If you wish to di spose of used electri cal
and electronic products outside the European Union, please contact
your local authority so as to comply with the correct disposal method.
Within the European Union–The device that produces less waste and
is easier to recycle is classifi ed as electronic device in terms of the
European Directive 2012/19/E U (WE E E), and must not be disposed
of as domestic garbage.
EU-wide legislation, as implemented in e ach Member State,
requires that waste electrical and ele ct ronic products carrying
the mark (left) must be disposed of separately from normal
household waste. This includes monit ors and electrical
accessories, such as signal cables or power cords. When you need to
dispose of your display product s, pl ease follow the guidance of your local
authority, or ask the shop where you purchased the product. The mark on
electrical and electronic produ ct s only applies to the current European
Union Member States.
Please follow the national guidelin es for electrical and electronic product
disposal.
Classification
Power by Class I power supply (IEI, POCm-W22/24C-ULT3)
No Applied Part.
No protection against the ingress of water: IPX0
Mode of operation: Continuous Operation
Page 17
16
The equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide: Not AP or APG
Category.
EMC Test Summary
Guidance and manufacturer’s declaration – electromagnetic emiss ions
The model POCm-W22/24C-ULT3 is intended for use in the electromagnetic
environment specified below. The customer or the user of the model
POCm-W22/24C-ULT3 s hou ld assur e that it i s used in such an environ m ent.
Emissions test
Compliance
Electromagnetic environm ent –
guidance
RF emissions
CISPR 11
The model POCm-W22/24C-ULT3
uses RF energy only for its internal
function. Therefore, its RF emissions
are very low and are not likely to
cause any interference in nea rby
electronic equipment.
RF emissions
CISPR 11
The model POCm-W22/24C-ULT3 is
suitable for use in all establishments,
including domestic establishm e nts
and those directly connec ted to the
public low-voltage power supply
network that supplies buildings used
for domestic purposes.
Harmonic emissi ons
IEC 61000-3-2
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Recommended separation distances betw een portable and mobile RF
communications equip ment and the model POCm-W22/24C-ULT3
The model POCm-W22/24C-ULT3 is intended for use in an electromagnetic
environment in which radiated RF disturbances are controlled. The customer or the
user of the model POCm-W22/24C-ULT3 can help prevent electromagnetic
interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the model POCm-W22/24C-ULT3as
recommended below, according to the maximum output power of the
communications equip ment.
Rated maximum
output power of
transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80
MHz
d = 1,2
80 MHz to 800
MHz
d = 1,2
800 MHz to 2,5
GHz
d = 2,3
0,01
0,12
0,12
0,23
0,1
0,38
0,38
0,73
1
1,2
1,2
2,3
10
3,8
3,8
7,3
100
12
12
23
PPP
Page 18
17
For transmitters rated at a maximum output power not listed above, the
recommended separation distan ce d in metres (m) can be esti ma ted using the
equation applicable to th e f requency of the transmitter, where P is t h e maximum
output power rating of the transmitter in watts (W) according to the transmitter
manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency
range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic
propagation is affected by absorption and reflection from structures, objects and
people.
Guidance and manufacturer’s declaration – electromag netic immunity
The model POCm-W22/24C-ULT3 is intended for use in the electromagnetic
environment specified below. The customer or the user of the model
POCm-W22/24C-ULT3 s hou ld assur e that it i s used in such an environ m ent.
Immunity test
IEC 60601 test
level
Compliance
level
Electromagnetic
environment – guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood,
concrete or ceramic tile.
If floors are covered
with synthetic material,
the relative humidity
should be at least 30 %.
Electrical fas t
transient/burst
IEC 61000-4-4
±2 kV for power
supply lines
±1 kV for
input/output
lines
±2 kV for power
supply lines
±1 kV for
input/output
lines
Mains power quality
should be that of a
typical commercial or
hospital environment.
Surge
IEC 61000-4-5
±1 kV line(s) to
line(s)
±2 kV line(s) to
earth
±1 kV line(s) to
line(s)
±2 kV line(s) to
earth
Mains power quality
should be that of a
typical commercial or
hospital environment.
interruptions
and
voltage
variations
on power supply
input lines
IEC 61000-4-11
<5 % UT
(>95 % dip in
UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
<5 % UT
(>95 % dip in
UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
Mains power quality
should be that of a
typical commercial or
hospital environment. If
the user of the model
POCm-W22/24C-ULT3
requires continued
operation during power
mains interruptions, it is
recommended that the
model
Page 19
18
for 25 cycles
<5 % UT
(>95 % dip in
UT)
for 5 sec
for 25 cycles
<5 % UT
(>95 % dip in
UT)
for 5 sec
POCm-W22/24C-ULT3
be powered from an
uninterruptible power
supply or a battery.
Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
3 A/m
3 A/m
Power frequency
magnetic fields should
be at levels
characteristic of a
typical location in a
typical commercial or
hospital environment.
NOTE: UT is the a.c. mains voltage prior to application of the test level .
Guidance and manufacturer’s declaration – electromag netic immunity
The model POCm-W22/24C-ULT3 is intended for use in the electromagnetic
environment specified below. The customer or the user of the model
POCm-W22/24C-ULT3 s hou ld assur e that it i s used in such an environ men t.
Immunity
test
IEC 60601
test level
Compliance
level
Electromagnetic environment –
guidance
Conducted
RF
IEC
61000-4-6
Radiated RF
IEC
61000-4-3
3 Vrms
150 kHz to 80
MHz
3 V/m
80 MHz to 2,5
GHz
Vrms
V/m
Portable and mobile RF
communications equipment
should be used no closer to any
part of the model
POCm-W22/24C-ULT3, including
cables, than the rec omme nded
separation distance calculated
from the equation applicable to
the frequency of the tr ansmitter.
Recommended separation
distance
d = 1,2
d = 1,2
80 MHz to 800 M Hz
d = 2,3
800 MHz to 2,5 GHz
where P is the maximum output
power rating of the transmitter
in watts (W) according to the
transmitter manufacturer and d
is the recommended separation
distance in metres (m).
P
P
P
Page 20
19
Field strengths from fixed RF
transmitters, as determined by
an electromagnetic site survey,
a
should be less than the
compliance level in each
frequency range.
b
Interference may occur in the
vicinity of equipment marked
with the following symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic
propagation is affected by absorption and reflection from structures, objects and
people.
a
Field strengths from fixed transmitters, su ch as b ase stations for radio
(cellular/cordless) telepho ne s and land mobile radios, amateur radio, AM and FM
radio broadcast and TV broadcast cannot be predicted theoretically with accuracy .
To assess the e lectromagnetic environment due to fixed RF transmitters, an
electromagnetic site survey should be considered. If the measured field strength in
the location in which the model POCm-W22/24C-ULT3 is used exceeds the
applicable RF compliance level above, the model POCm-W22/24C-ULT3 should be
observed to verify normal operation. If abnormal performance is observed,
additional measures may be necessary, such as reorienting or relocating the model
POCm-W22/24C-ULT3.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than
V/m.
Contact Information
IEI Integration Corp.
No. 29, Zongxing Rd., Xizhi Dist.,
New Taipei City 221, Taiwan
TEL: +886-2-8691-6798
Fax: +886-2-6616-0028
www.ieiworld.com
sales@ieiworld.com.tw
Loading...