IEI Technology PCIE-H610 User Manual

Download

PCIE-H610 PICMG 1.3 CPU Card

MODEL:

PCIE-H610

Full-Size PICMG 1.3 CPU Card Supports 32nm LGA1155 Intel®

Core™ i7/i5/i3/Pentium®/Celeron® CPU, Intel® H61 Chipset,

DDR3, VGA, DVI-D, Dual Realtek PCIe GbE, USB 2.0,

SATA 3Gb/s, HD Audio and RoHS

User Manual

Rev. 1.05 – November 16, 2015

Page i

PCIE-H610 PICMG 1.3 CPU Card

Revision

Date Version Changes

November 16, 2015 1.05 Updated Section 1.7: Technical Specifications

August 25, 2015 1.04 Modified Section 3.2.15: Serial Port Connectors, RS-232

November 5, 2014 1.03 Modified LAN pinouts

Updated Chapter

November 14, 2013 1.02 Updated Section 1.7: Technical Specifications

January 21, 2013 1.01 Updated the LPT cable P/N and RS-422/485 connector

pinouts

February 17, 2012 1.00 Initial release

2: Packing List

Page ii

PCIE-H610 PICMG 1.3 CPU Card

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners.

Page iii

PCIE-H610 PICMG 1.3 CPU Card

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes.

HOT SURFACE

This symbol indicates a hot surface that should not be touched without taking care.

Page iv

PCIE-H610 PICMG 1.3 CPU Card

Table of Contents

1 INTRODUCTION.......................................................................................................... 1

1.1 INTRODUCTION........................................................................................................... 2

1.2 MODEL VARIATIONS ................................................................................................... 2

1.3 FEATURES................................................................................................................... 3

1.4 CONNECTORS ............................................................................................................. 3

1.5 DIMENSIONS............................................................................................................... 4

1.6 DATA FLOW................................................................................................................ 6

1.7 TECHNICAL SPECIFICATIONS ...................................................................................... 7

2 PACKING LIST........................................................................................................... 10

2.1 ANTI-STATIC PRECAUTIONS.......................................................................................11

2.2 UNPACKING PRECAUTIONS........................................................................................11

2.3 PACKING LIST........................................................................................................... 12

2.4 OPTIONAL ITEMS...................................................................................................... 13

3 CONNECTORS ........................................................................................................... 16

3.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 17

3.1.1 PCIE-H610 Layout .......................................................................................... 17

3.1.2 Peripheral Interface Connectors ..................................................................... 17

3.1.3 External Interface Panel Connectors............................................................... 18

3.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 19

3.2.1 Audio Kit Connector........................................................................................ 19

3.2.2 Battery Connector............................................................................................ 20

3.2.3 CPU Power Input Connector........................................................................... 21

3.2.4 DDR3 DIMM Slots........................................................................................... 21

3.2.5 Digital I/O Connector...................................................................................... 22

3.2.6 DVI-D Connector (DVI Model Only) .............................................................. 23

3.2.7 Fan Connector (CPU)...................................................................................... 24

3.2.8 Floppy Disk Drive Connector.......................................................................... 25

3.2.9 Front Panel Connector.................................................................................... 26

Page v

3.2.10 I2C Connector................................................................................................ 27

3.2.11 Infrared Interface Connector......................................................................... 27

3.2.12 Keyboard/Mouse Connector.......................................................................... 28

3.2.13 Parallel Port Connector ................................................................................ 29

3.2.14 SATA 3Gb/s Drive Connectors....................................................................... 30

3.2.15 Serial Port Connectors, RS-232..................................................................... 31

3.2.16 Serial Port Connector, RS-422/485................................................................ 32

3.2.17 SMBus Connector .......................................................................................... 33

3.2.18 SPI ROM Connector...................................................................................... 33

3.2.19 TPM Connector.............................................................................................. 34

3.2.20 USB Connectors............................................................................................. 35

3.3 EXTERNAL PERIPHERAL INTERFACE CONNECTOR PANEL ......................................... 36

3.3.1 Ethernet Connectors ........................................................................................ 36

3.3.2 USB Connectors............................................................................................... 37

PCIE-H610 PICMG 1.3 CPU Card

3.3.3 VGA Connector................................................................................................ 37

4 INSTALLATION ......................................................................................................... 39

4.1 ANTI-STATIC PRECAUTIONS...................................................................................... 40

4.2 INSTALLATION CONSIDERATIONS.............................................................................. 40

4.2.1 Socket LGA1155 CPU Installation .................................................................. 42

4.2.2 Socket LGA1155 Cooling Kit Installation........................................................ 45

4.2.3 DIMM Installation........................................................................................... 46

4.3 JUMPER SETTINGS .................................................................................................... 47

4.3.1 AT/ATX Power Select Jumper.......................................................................... 47

4.3.2 Clear CMOS Jumper........................................................................................ 48

4.3.3 Wake-on LAN Jumper ...................................................................................... 49

4.4 CHASSIS INSTALLATION............................................................................................ 50

4.4.1 Airflow.............................................................................................................. 50

4.4.2 CPU Card Installation..................................................................................... 50

4.5 INTERNAL PERIPHERAL DEVICE CONNECTIONS........................................................ 50

4.5.1 Dual RS-232 Cable with Slot Bracket.............................................................. 51

4.5.2 DVI-D/USB Kit Installation (DVI Model Only)............................................... 52

4.5.3 SATA Drive Connection ................................................................................... 53

4.5.4 USB Cable (Dual Port) with Slot Bracket ....................................................... 54

4.6 EXTERNAL PERIPHERAL INTERFACE CONNECTION................................................... 55

Page vi

PCIE-H610 PICMG 1.3 CPU Card

4.6.1 LAN Connection............................................................................................... 55

4.6.2 USB Device Connection (Single Connector)................................................... 56

4.6.3 VGA Monitor Connection ................................................................................ 57

5 BIOS.............................................................................................................................. 59

5.1 INTRODUCTION......................................................................................................... 60

5.1.1 Starting Setup................................................................................................... 60

5.1.2 Using Setup...................................................................................................... 60

5.1.3 Getting Help..................................................................................................... 61

5.1.4 Unable to Reboot after Configuration Changes.............................................. 61

5.1.5 BIOS Menu Bar................................................................................................ 61

5.2 MAIN........................................................................................................................ 62

5.3 ADVANCED............................................................................................................... 63

5.3.1 ACPI Settings................................................................................................... 64

5.3.2 T rusted Computing........................................................................................... 65

5.3.3 CPU Configuration.......................................................................................... 65

5.3.3.1 CPU Information....................................................................................... 66

5.3.4 SATA Configuration ......................................................................................... 68

5.3.5 Intel TXT(LT) Configuration............................................................................ 69

5.3.6 USB Configuration........................................................................................... 70

5.3.7 Super IO Configuration ................................................................................... 71

5.3.7.1 Floppy Disk Controller Configuration...................................................... 72

5.3.7.2 Serial Port n Configuration....................................................................... 73

5.3.7.3 Parallel Port Configuration....................................................................... 77

5.3.8 H/W Monitor.................................................................................................... 78

5.3.8.1 FAN 1 Configuration ................................................................................ 80

5.3.9 Serial Port Console Redirection...................................................................... 81

5.3.10 iEi Feature..................................................................................................... 84

5.4 CHIPSET ................................................................................................................... 85

5.4.1 Northbridge Configuration.............................................................................. 86

5.4.2 Southbridge Configuration .............................................................................. 88

5.4.3 Integrated Graphics......................................................................................... 90

5.5 BOOT........................................................................................................................ 91

5.6 SECURITY................................................................................................................. 93

5.7 EXIT......................................................................................................................... 94

Page vii

6 SOFTWARE DRIVERS.............................................................................................. 96

6.1 AVAILABLE SOFTWARE DRIVERS .............................................................................. 97

6.2 SOFTWARE INSTALLATION ........................................................................................ 97

6.3 CHIPSET DRIVER INSTALLATION............................................................................... 99

6.4 GRAPHICS DRIVER INSTALLATION.......................................................................... 102

6.5 LAN DRIVER INSTALLATION.................................................................................. 105

6.6 AUDIO DRIVER INSTALLATION ............................................................................... 107

A REGULATORY COMPLIANCE............................................................................ 109

B BIOS OPTIONS .........................................................................................................111

C TERMINOLOGY ......................................................................................................114

D DIGITAL I/O INTERFACE......................................................................................118

D.1 INTRODUCTION.......................................................................................................119

PCIE-H610 PICMG 1.3 CPU Card

D.2 ASSEMBLY LANGUAGE SAMPLE 1.......................................................................... 120

D.3 ASSEMBLY LANGUAGE SAMPLE 2.......................................................................... 120

E WATCHDOG TIMER............................................................................................... 121

F HAZARDOUS MATERIALS DISCLOSURE........................................................ 124

F.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS

ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 125

Page viii

PCIE-H610 PICMG 1.3 CPU Card

List of Figures

Figure 1-1: PCIE-H610....................................................................................................................2

Figure 1-2: Connectors ..................................................................................................................3

Figure 1-3: PCIE-H610 Dimensions (mm).....................................................................................4

Figure 1-4: External Interface Panel Dimensions (mm)..............................................................5

Figure 1-5: Data Flow Diagram......................................................................................................6

Figure 3-1: Connectors and Jumpers.........................................................................................17

Figure 3-2: Audio Connector Location.......................................................................................19

Figure 3-3: Battery Connector Location.....................................................................................20

Figure 3-4: ATX Power Connector Pinout Location..................................................................21

Figure 3-5: DDR3 DIMM Slot Locations......................................................................................22

Figure 3-6: Digital I/O Connector Location ................................................................................22

Figure 3-7: DVI-D Connector Location .......................................................................................23

Figure 3-8: CPU Fan Connector Location..................................................................................24

Figure 3-9: Floppy Disk Location................................................................................................25

Figure 3-10: Front Panel Connector Location ...........................................................................26

Figure 3-11: I2C Connector Location..........................................................................................27

Figure 3-12: Infrared Connector Location..................................................................................28

Figure 3-13: Keyboard/Mouse Connector Location..................................................................28

Figure 3-14: Parallel Port Connector Location..........................................................................29

Figure 3-15: SATA 3Gb/s Drive Connector Location................................................................30

Figure 3-16: Serial Port Connector Location.............................................................................31

Figure 3-17: RS-422/485 Connector Location............................................................................32

Figure 3-18: SMBus Connector Location...................................................................................33

Figure 3-19: SPI Connector Location .........................................................................................34

Figure 3-20: TPM Connector Location........................................................................................34

Figure 3-21: USB Connector Pinout Locations.........................................................................35

Figure 3-22: External Peripheral Interface Connector..............................................................36

Figure 3-23: Ethernet Connector.................................................................................................36

Figure 3-24: VGA Connector .......................................................................................................38

Figure 4-1: Disengage the CPU Socket Load Lever..................................................................42

Page ix

Figure 4-2: Remove Protective Cover.........................................................................................43

Figure 4-3: Insert the Socket LGA1155 CPU..............................................................................44

Figure 4-4: Close the Socket LGA1155 ......................................................................................44

Figure 4-5: Cooling Kit Support Bracket....................................................................................45

Figure 4-6: DIMM Installation.......................................................................................................46

Figure 4-7: AT/ATX Power Mode Jumper Location...................................................................48

Figure 4-8: Clear BIOS Jumper Location ...................................................................................49

Figure 4-9: Wake-on LAN Jumper Location...............................................................................49

Figure 4-10: Dual RS-232 Cable Installation..............................................................................51

Figure 4-11: DVI-D/USB Kit Installation......................................................................................52

Figure 4-12: SATA Drive Cable Connection...............................................................................53

Figure 4-13: SATA Power Drive Connection..............................................................................54

Figure 4-14: Dual USB Cable Connection..................................................................................55

Figure 4-15: LAN Connection......................................................................................................56

PCIE-H610 PICMG 1.3 CPU Card

Figure 4-16: USB Device Connection.........................................................................................57

Figure 4-17: VGA Connector .......................................................................................................58

Figure 6-1: Introduction Screen..................................................................................................98

Figure 6-2: Available Drivers.......................................................................................................98

Figure 6-3: Chipset Driver Screen...............................................................................................99

Figure 6-4: Chipset Driver Welcome Screen........................................................................... 100

Figure 6-5: Chipset Driver License Agreement...................................................................... 100

Figure 6-6: Chipset Driver Read Me File ................................................................................. 101

Figure 6-7: Chipset Driver Setup Operations ......................................................................... 101

Figure 6-8: Chipset Driver Installation Finish Screen............................................................ 102

Figure 6-9: Graphics Driver Welcome Screen........................................................................ 103

Figure 6-10: Graphics Driver License Agreement.................................................................. 103

Figure 6-11: Graphics Driver Setup Operations..................................................................... 104

Figure 6-12: Graphics Driver Installation Finish Screen ....................................................... 104

Figure 6-13: LAN Driver Welcome Screen .............................................................................. 105

Figure 6-14: LAN Driver Installation ........................................................................................ 106

Figure 6-15: LAN Driver Installation Complete....................................................................... 106

Figure 6-16: Audio Driver – Extracting Files........................................................................... 107

Figure 6-17: Audio Driver Installation Welcome Screen........................................................ 108

Figure 6-18: Audio Driver Installation...................................................................................... 108

Figure 6-19: Audio Driver Installation Complete.................................................................... 108

Page x

PCIE-H610 PICMG 1.3 CPU Card

List of Tables

Table 1-1: PCIE-H610 Model Variations........................................................................................2

Table 1-2: PCIE-H610 Specifications............................................................................................9

Table 2-1: Packing List.................................................................................................................13

Table 2-2: Optional Items.............................................................................................................15

Table 3-1: Peripheral Interface Connectors...............................................................................18

Table 3-2: Rear Panel Connectors..............................................................................................18

Table 3-3: Audio Connector Pinouts ..........................................................................................19

Table 3-4: Battery Connector Pinouts........................................................................................20

Table 3-5: ATX Power Connector Pinouts .................................................................................21

Table 3-6: Digital I/O Connector Pinouts....................................................................................23

Table 3-7: DVI-D Connector Pinouts...........................................................................................24

Table 3-8: CPU Fan Connector Pinouts......................................................................................24

Table 3-9: Floppy Disk Pinouts...................................................................................................26

Table 3-10: Front Panel Connector Pinouts...............................................................................26

Table 3-11: I2C Connector Pinouts.............................................................................................27

Table 3-12: Infrared Connector Pinouts.....................................................................................28

Table 3-13: Keyboard/Mouse Connector Pinouts .....................................................................29

Table 3-14: Parallel Port Connector Pinouts .............................................................................30

Table 3-15: SATA 3Gb/s Drive Connector Pinouts....................................................................31

Table 3-16: Serial Port Connector Pinouts ................................................................................31

Table 3-17: RS-422/485 Connector Pinouts...............................................................................32

Table 3-18: DB-9 RS-422/485 Pinouts.........................................................................................32

Table 3-19: SMBus Connector Pinouts ......................................................................................33

Table 3-20: SPI Connector Pinouts.............................................................................................34

Table 3-21: TPM Connector Pinouts...........................................................................................35

Table 3-22: USB Port Connector Pinouts...................................................................................35

Table 3-23: LAN Pinouts ..............................................................................................................36

Table 3-24: Connector LEDs........................................................................................................37

Table 3-25: USB Port Pinouts......................................................................................................37

Table 3-26: VGA Connector Pinouts...........................................................................................38

Page xi

Table 4-1: Jumpers.......................................................................................................................47

Table 4-2: AT/ATX Power Mode Jumper Settings.....................................................................48

Table 4-3: Clear BIOS Jumper Settings......................................................................................48

Table 4-4: Wake-on LAN Jumper Settings.................................................................................49

Table 4-5: Wake-on LAN Jumper Pinouts..................................................................................50

Table 5-1: BIOS Navigation Keys................................................................................................61

PCIE-H610 PICMG 1.3 CPU Card

Page xii

PCIE-H610 PICMG 1.3 CPU Card

BIOS Menus

BIOS Menu 1: Main.......................................................................................................................62

BIOS Menu 2: Advanced..............................................................................................................63

BIOS Menu 3: ACPI Configuration..............................................................................................64

BIOS Menu 4: TPM Configuration...............................................................................................65

BIOS Menu 5: CPU Configuration...............................................................................................66

BIOS Menu 6: CPU Configuration...............................................................................................67

BIOS Menu 7: SATA Configuration.............................................................................................68

BIOS Menu 8: Intel TXT(LT) Configuration ................................................................................69

BIOS Menu 9: USB Configuration...............................................................................................70

BIOS Menu 10: Super IO Configuration......................................................................................71

BIOS Menu 11: Serial Port n Configuration Menu.....................................................................72

BIOS Menu 12: Serial Port n Configuration Menu.....................................................................73

BIOS Menu 13: Parallel Port Configuration Menu.....................................................................77

BIOS Menu 14: H/W Monitor........................................................................................................79

BIOS Menu 15: FAN 1 Configuration..........................................................................................80

BIOS Menu 16: Serial Port Console Redirection.......................................................................82

BIOS Menu 17: IEI Feature...........................................................................................................84

BIOS Menu 18: Chipset................................................................................................................85

BIOS Menu 19:Northbridge Chipset Configuration...................................................................86

BIOS Menu 20: Southbridge Chipset Configuration.................................................................88

BIOS Menu 21: Integrated Graphics...........................................................................................90

BIOS Menu 22: Boot.....................................................................................................................91

BIOS Menu 23: Security...............................................................................................................93

BIOS Menu 24:Exit........................................................................................................................94

PCIE-H610

Page xiii

PCIE-H610 PICMG 1.3 CPU Card

Chapter

1 Introduction

Page 1

1.1 Introduction

Figure 1-1: PCIE-H610

PCIE-H610 PICMG 1.3 CPU Card

The PCIE-H610 PICMG 1.3 CPU card is a Socket LGA1155 32nm Intel® Core i3/i5/i7/Pentium®/Celeron® processor platform that supports two 240-pin 1066/1333 MHz dual-channel DDR3/DDR3L DIMM modules up to 16.0 GB.

The PCIE-H610 supports two GbE interfaces through the Realtek RTL8111E PCIe Ethernet controllers. The integrated Intel® H61 chipset supports four SATA 3Gb/s drives. Two USB 2.0 on the rear panel, four USB 2.0 by pin header and four USB 2.0 by backplane pin header (via golden fingers) provide flexible expansion options. High Definition Audio (HDA) support ensures HDA devices can be easily implemented on the PCIE-H610.

1.2 Model Variations

The model variations of the PCIE-H610 are listed below.

Model No. CPU Supported DVI-D by 26-pin header

PCIE-H610-DVI-R10

LGA1155 Intel® Core™ i7/i5/i3/Pentium®/Celeron®

Yes

PCIE-H610-R10

Table 1-1: PCIE-H610 Model Variations

Page 2

LGA1155 Intel® Core™ i7/i5/i3/Pentium®/Celeron®

PCIE-H610 PICMG 1.3 CPU Card

1.3 Features

Some of the PCIE-H610 motherboard features are listed below:

 PICMG 1.3 full-size graphics grade solution  LGA1155 CPU socket  Intel® H61 chipset  Dual-channel DDR3/DDR3L DIMMs support up to 16.0 GB  Dual independent display by VGA and DVI-D (DVI model only)  Two Realtek PCIe Gigabit Ethernet connectors (LAN1 with ASF 2.0 support)  Four SATA 3Gb/s connectors  TPM V1.2 hardware security function supported by the TPM module  High Definition Audio  RoHS compliant

1.4 Connectors

The connectors on the PCIE-H610 are shown in the figure below.

Figure 1-2: Connectors

Page 3

1.5 Dimensions

The main dimensions of the PCIE-H610 are shown in the diagram below.

PCIE-H610 PICMG 1.3 CPU Card

Figure 1-3: PCIE-H610 Dimensions (mm)

Page 4

PCIE-H610 PICMG 1.3 CPU Card

Figure 1-4: External Interface Panel Dimensions (mm)

Page 5

1.6 Data Flow

5Figure 1-5 shows the data flow between the system chipset, the CPU and other

components installed on the motherboard.

PCIE-H610 PICMG 1.3 CPU Card

Figure 1-5: Data Flow Diagram

Page 6

PCIE-H610 PICMG 1.3 CPU Card

1.7 Technical Specifications

The PCIE-H610 technical specifications are listed below.

Specification/Model PCIE-H610

Form Factor CPU Supported PCH Memory

Graphics Engine

Audio BIOS

Ethernet Controllers

PICMG 1.3 LGA1155 Intel® Core™ i7/i5/i3/Pentium®/Celeron® CPU Intel® H61 Two 240-pin 1333/1066 MHz dual-channel unbuffered DDR3/DDR3L

(1.35V) SDRAM DIMMs support (system max. 16.0 GB) Intel® HD Graphics 2000/3000

Supports DirectX 10.1 and OpenGL 3.0 Full MPEG2, VC1, AVC Decode

Supports IEI AC-KIT-892HD audio kit UEFI BIOS

B222ARxx supports four PCIe x1 slots (default) V34QARxx supports one PCIe x4 slot

Dual Realtek RTL8111E PCIe GbE Ethernet controller (LAN1 with ASF 2.0 support)

Super I/O Controller Watchdog Timer Expansions

I/O Interface Connectors Audio Connector Digital I/O

Fintek F81866 Software programmable supports 1~2 55 sec. system reset 4 x PCI link via golden finger

16-lane PCIe link from CPU via golden finger:

Support one PCIe x16 slot on the backplane

4-lane PCIe link from PCH via golden finger:

Support either one PCIe x4 slot or four PCIe x1 slots on the backplane For installing the P CIe x4 de vice on th e backpl ane, the u ser must update BIOS to the version which sup port s one PCI e x4 slot

One internal audio connector (10-pin header) 8-bit digital I/O

Page 7

PCIE-H610 PICMG 1.3 CPU Card

Display Output

Ethernet Fan FDD Front Panel

I2C Infrared Keyboard/Mouse Parallel Port Serial ATA Serial Ports

One VGA integrated in the Intel® H61 (rear I/O) One DVI-D integrated in the Intel® H61 (via 26-pin header to the

DVI-D/USB kit; DVI model only) Two RJ-45 GbE port s One 4-pin wafer connector One 34-pin floppy disk drive connector One 14-pin header (power LED, HDD LED, speaker, power button,

reset button) One 4-pin wafer connector One via 5-pin header One 6-pin wafer connector One parallel port via internal 26-pin box header Four SATA 3Gb/s connectors Two RS-232 via internal box headers

One RS-422/485 via internal 4-pin wafer connector

SMBus TPM USB Ports

Environmental and Power Specifications Power Supply Power Consumption

Operating Temperature Storage Temperature Humidity

One 4-pin wafer connector One via 20-pin header Two external USB 2.0 ports on rear IO

Four internal USB 2.0 ports by two pin headers Four USB 2.0 ports by backplane pin headers via golden fingers

5V/12V, AT/ATX power supported 5V@4.41A , 12V@0.21A, Vcore_12V@7.72A, 5VSB@0.16A

(3.40 GHz Intel® Core i7-2600K CPU with two 2GB 1333 MHz DDR3 memory)

-10ºC ~ 60ºC

-20ºC ~ 70ºC 5% ~ 95% (non-condensing)

Physical Specifications

Page 8

PCIE-H610 PICMG 1.3 CPU Card

Dimensions Weight (GW/NW) Table 1-2: PCIE-H610 Specifications

338 mm x 126 mm 1200 g / 420 g

Page 9

PCIE-H610 PICMG 1.3 CPU Card

Chapter

2 Packing List

Page 10

PCIE-H610 PICMG 1.3 CPU Card

2.1 Anti-static Precautions

WARNING!

Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user.

Make sure to adhere to the following guidelines:

 Wear an anti-static wristband: Wearing an anti-static wristband can prevent

electrostatic discharge.

 Self-grounding: Touch a grounded conductor every few minutes to discharge

any excess static buildup.

 Use an anti-static pad: When configuring any circuit board, place it on an

anti-static mat.

 Only handle the edges of the PCB: Don't touch the surface of the

motherboard. Hold the motherboard by the edges when handling.

2.2 Unpacking Precautions

When the PCIE-H610 is unpacked, please do the following:

 Follow the anti-static guidelines above.  Make sure the packing box is facing upwards whe n opening.  Make sure all the packing list items are present.

Page 11

2.3 Packing List

NOTE:

If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the PCIE-H610 was purchased from or contact an IEI sales representative directly by sending an email to 32sales@ieiworld.com.

The PCIE-H610 is shipped with the following components:

Quantity Item and Part Number Image

1 PCIE-H610 CPU card

PCIE-H610 PICMG 1.3 CPU Card

4 SATA cable

(P/N: 32000-062800-RS)

1 Dual RS-232 cable

(P/N: 19800-000051-RS)

1 Dual USB cable with bracket

(P/N: 19800-003100-300-RS)

1 Mini jumper pack

1 DVI-D/USB kit (DVI model only)

(P/N: IO-KIT-001-R20)

Page 12

PCIE-H610 PICMG 1.3 CPU Card

Quantity Item and Part Number Image

1 One Key Recovery CD

1 Utility CD

1 Quick Installation Guide

Table 2-1: Packing List

2.4 Optional Items

The following are optional components which may be separately purchased:

Item and Part Number Image

RS-422/485 cable, 200 mm (P/N: 32205-003800-300-RS)

KB/MS cable with bracket (P/N: 19800-000075-RS)

SATA to IDE/CF converter board (P/N: SAIDE-KIT01-R10)

SATA power cable (P/N: 32102-000100-200-RS)

FDD flat cable (P/N: 32200-000017-RS)

Page 13

Item and Part Number Image

LPT cable (P/N: 19800-000049-RS)

7.1-channel HD audio kit with Realtek ALC892 audio codec supporting dual audio stream (P/N: AC-KIT-892HD-R10)

Infineon TPM module (P/N: TPM-IN01-R1 1)

LGA1155/LGA1156 cool er kit (1U chas sis compatible, 73W)

PCIE-H610 PICMG 1.3 CPU Card

(P/N: CF-1 156A-RS-R11)

LGA1155/LGA1156 cool er kit (1U chas sis compatible, 45W)

(P/N: CF-1 156C-RS)

LGA1155/LGA1156 cool er kit (1U chas sis compatible, 65W)

(P/N: CF-1 156D-RS)

High-performance LGA1155/LGA1 156 cooler kit (95W) (P/N: CF-1156E-R11)

Intel® Core™ i5-2500T processor (LGA1155, quad core

2.3 GHz, 6M cache, 45W, compatible with CF-1156C-RS

Page 14

CPU cooler kit) (P/N: CPU-DT-i5-2500T)

PCIE-H610 PICMG 1.3 CPU Card

Item and Part Number Image

Intel® Core™ i5-2390T processor (LGA1155, dual core

2.7 GHz, 3M cache, 35W, compatible with CF-1156C-RS CPU cooler kit)

(P/N: CPU-DT-i5-2390T) Intel® Core™ i3-2120T processor (LGA1155, dual core

2.6 GHz, 3M cache, 35W, compatible with CF-1156C-RS CPU cooler kit)

(P/N: CPU-DT-i3-2120T) Intel® Pentium® G630T processor (LGA1155, dual core

2.3 GHz, 3M cache, 35W, compatible with CF-1156C-RS CPU cooler kit)

(P/N: CPU-DT-P-G630T) Intel® Celeron® G440 processor (LGA1155, single core

1.6 GHz, 1M cache, 35W, compatible with CF-1156C-RS CPU cooler kit)

(P/N: CPU-DT-C-G440)

Table 2-2: Optional Items

Page 15

PCIE-H610 PICMG 1.3 CPU Card

Chapter

3 Connectors

Page 16

PCIE-H610 PICMG 1.3 CPU Card

3.1 Peripheral Interface Connectors

This chapter details all the jumpers and connectors.

3.1.1 PCIE-H610 Layout

The figures below show all the connectors and jumpers.

Figure 3-1: Connectors and Jumpers

3.1.2 Peripheral Interface Connectors

The table below lists all the connectors on the board.

Connector Type Label

Audio kit connector 10-pin header J_AUDIO1 Battery connector 2-pin wafer BT2 CPU power input connector 4-pin Molex power

DDR3 DIMM sockets 240-pin socket CHA_DIMM1

Digital I/O connector 10-pin header DIO1 DVI-D connector (DVI model only) 26-pin header DVI1

CPU12V1

connector

CHB_DIMM1

Page 17

Connector Type Label

Fan connector (CPU) 4-pin wafer CPU_FAN1 Floppy disk drive connector 34-pin box header FDD1 Front panel connector 14-pin header F_PANEL1 I2C connector 4-pin wafer I2C_1 Infrared connector 5-pin header IR1 Keyboard and mouse connector 6-pin wafer KB_MS1 Parallel port connector 26-pin box header LPT1 SATA 3Gb/s drive connector 7-pin SATA connector SATA1, SATA2,

Serial port, RS-422/485 4-pin wafer COM3 Serial port, RS-232 10-pin box header COM1, COM2

PCIE-H610 PICMG 1.3 CPU Card

SATA3, SATA4

SMBus connector 4-pin wafer SMBUS_1 SPI ROM connector 8-pin header JSPI1 TPM connector 20-pin header TPM1 USB connectors 8-pin header USB1, USB2

Table 3-1: Peripheral Interface Connectors

3.1.3 External Interface Panel Connectors

The table below lists the connectors on the external I/O panel.

Connector Type Label

Ethernet connector RJ-45 LAN1 Ethernet connector RJ-45 LAN2 USB port USB USB_C1 USB port USB USB_C2

Page 18

VGA connector 15-pin female VGA1

Table 3-2: Rear Panel Connectors

PCIE-H610 PICMG 1.3 CPU Card

3.2 Internal Peripheral Connectors

The section describes all of the connectors on the PCIE-H610.

3.2.1 Audio Kit Connector

CN Label: J_AUDIO1 CN Type: CN Location: CN Pinouts:

This connector connects to an external audio kit.

10-pin header

Figure 3-2

See

Table 3-3

See

Figure 3-2: Audio Connector Location

Pin Description Pin Description

1 ACZ_SYNC 2 ACZ_BITCLK 3 ACZ_SDOUT 4 ACZ_PCBEEP 5 ACZ_SDIN 6 ACZ_RST# 7 ACZ_VCC 8 ACZ_GND 9 ACZ_12V 10 ACZ_GND

Table 3-3: Audio Connector Pinouts

Page 19

3.2.2 Battery Connector

CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.

Dispose of used batteries according to instructions and local regulations.

CN Label: BT2

PCIE-H610 PICMG 1.3 CPU Card

CN Type: CN Location: CN Pinouts:

This is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off.

Figure 3-3: Battery Connector Location

2-pin wafer

Figure 3-3

See

Table 3-4

See

Pin Description

1 Battery+ 2 GND

Page 20

Table 3-4: Battery Connector Pinouts

PCIE-H610 PICMG 1.3 CPU Card

3.2.3 CPU Power Input Connector

CN Label: CPU12V1 CN Type: CN Location: CN Pinouts:

The connector supports the 12V power supply.

Figure 3-4: ATX Power Connector Pinout Location

4-pin Molex power connector

Figure 3-4

See

Table 3-5

See

Pin Description Pin Description

1 GND 2 GND 3 +12V 4 +12V

Table 3-5: ATX Power Connector Pinouts

3.2.4 DDR3 DIMM Slots

CN Label: CHA_DIMM1, CHB_DIMM1 CN Type: CN Location:

The DIMM slots are for DDR3 DIMM memory modules.

DDR3 DIMM slot See 5Figure 3-5

Page 21

Figure 3-5: DDR3 DIMM Slot Locations

3.2.5 Digital I/O Connector

CN Label: DIO1

PCIE-H610 PICMG 1.3 CPU Card

CN Type: CN Location: CN Pinouts:

The digital I/O connector provides programmable input and output for external devices.

Figure 3-6: Digital I/O Connector Location

10-pin header See Figure 3-6 See Table 3-6

Pin Description Pin Description

Page 22

1 GND 2 VCC 3 Output 3 4 Output 2 5 Output 1 6 Output 0

PCIE-H610 PICMG 1.3 CPU Card

Pin Description Pin Description

7 Input 3 8 Input 2 9 Input 1 10 Input 0

Table 3-6: Digital I/O Connector Pinouts

3.2.6 DVI-D Connector (DVI Model Only)

CN Label: DVI1 CN Type: CN Location: CN Pinouts:

26-pin header

Figure 3-7

See

Table 3-7

See

The DVI-D connector connects to a monitor that supports DVI video input via the DVI-D/USB kit.

Figure 3-7: DVI-D Connector Location

Pin Description Pin Description

1 3 5 7 9 11 13 15 17

CK_DVI_DATA2# CK_DVI_DATA2 GND NC NC DVI_SCL DVI_SDA NC CK_DVI_DATA1#

2 4 6 8 10 12 14 16 18

DVI_VCC GND HP_DET CK_DVI_DATA0# CK_DVI_DATA0 GND NC NC GND

Page 23

Pin Description Pin Description

PCIE-H610 PICMG 1.3 CPU Card

19 CK_DVI_DATA1 20

GND NC

21 23 25 NC

22 CK_DVI_CLK 24

Table 3-7: DVI-D Connector Pinouts

3.2.7 Fan Connector (CPU)

CN Label: CPU_FAN1 CN Type: CN Location: CN Pinouts:

The fan connector attaches to a CPU cooling fan.

4-pin wafer See Figure 3-8 See Table 3-8

CK_DVI_CLK#

GND

Page 24

Figure 3-8: CPU Fan Connector Location

Pin Description

1 GND 2 +12 V 3 Rotation Signal 4 PWM Control Signal

Table 3-8: CPU Fan Connector Pinouts

PCIE-H610 PICMG 1.3 CPU Card

3.2.8 Floppy Disk Drive Connector

CN Label: FDD1 CN Type: CN Location: CN Pinouts:

34-pin header

Figure 3-9

See

Table 3-9

See

The floppy disk drive connector is connected to a floppy disk drive.

Figure 3-9: Floppy Disk Location

Pin Description Pin Description

1 GND 2 DENSEL 3 GND 4 NC 5 NC 6 NC 7 GND 8 INDEX9 GND 10 MOTEA11 GND 12 NC 13 GND 14 DRVA15 GND 16 NC 17 GND 18 DIR19 GND 20 STEP21 GND 22 WDATA23 GND 24 WGATE25 GND 26 TK0027 GND 28 WPT-

Page 25

Pin Description Pin Description

29 GND 30 RDATA31 GND 32 SIDE133 GND 34 DSKCHG-

Table 3-9: Floppy Disk Pinouts

3.2.9 Front Panel Connector

CN Label: F_PANEL1

PCIE-H610 PICMG 1.3 CPU Card

CN Type: CN Location: CN Pinouts:

14-pin header See Figure 3-10 See Table 3-10

The front panel connector connects to the indicator LEDs and buttons on the computer's front panel.

Figure 3-10: Front Panel Connector Location

Function Pin Description Function Pin Description

Page 26

Power LED 1 +5V Speaker 2 +5V 3 N/C 4 N/C 5 GROUND 6 N/C Power Button 7 PWR_BTN+ 8 Speaker 9 PWR_BTN- Reset 10 N/C HDD LED 11 +5V 12 RESET 13 HDD_LED- 14 GROUND

Table 3-10: Front Panel Connector Pinouts

PCIE-H610 PICMG 1.3 CPU Card

3.2.10 I2C Connector

CN Label: I2C_1 CN Type: CN Location: CN Pinouts:

The I2C connector is for system debug.

Figure 3-11: I2C Connector Location

4-pin wafer

Figure 3-11

See

Table 3-11

See

Pin Description

1 +5VS 2 PCH_GP38_PU 3 PCH_GP39_PU 4 GND

Table 3-11: I2C Connector Pinouts

3.2.11 Infrared Interface Connector

CN Label: IR1 CN Type: CN Location: CN Pinouts:

The infrared connector attaches to an infrared receiver for use with remote controls.

5-pin header

Figure 3-12

See

Table 3-12

See

Page 27

PCIE-H610 PICMG 1.3 CPU Card

Figure 3-12: Infrared Connector Location

Pin Description

1 VCC 2 NC 3 IR-RX 4 GND 5 IR-TX

Table 3-12: Infrared Connector Pinouts

3.2.12 Keyboard/Mouse Connector

CN Label: KB_MS1 CN Type: CN Location: CN Pinouts:

The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a PS/2 keyboard and mouse.

6-pin wafer

Figure 3-13

See

Table 3-13

See

Page 28

Figure 3-13: Keyboard/Mouse Connector Location

PCIE-H610 PICMG 1.3 CPU Card

Pin Description

1 +5 VCC 2 Mouse Data 3 Mouse Clock 4 Keyboard Data 5 Keyboard Clock 6 GROUND

Table 3-13: Keyboard/Mouse Connector Pinouts

3.2.13 Parallel Port Connector

CN Label: LPT1 CN Type: CN Location: CN Pinouts:

26-pin box header

Figure 3-14

See

Table 3-14

See

The parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer.

Figure 3-14: Parallel Port Connector Location

Pin Description Pin Description

1 STB 2 AFD 3 PPD0 4 ERROR 5 PPD1 6 INIT 7 PPD2 8 SLIN

Page 29

Pin Description Pin Description

9 PPD3 10 GND 11 PPD4 12 GND 13 PPD5 14 GND 15 PPD6 16 GND 17 PPD7 18 GND 19 ACK 20 GND 21 BUSY 22 GND 23 PE 24 GND 25 SLCT

Table 3-14: Parallel Port Connector Pinouts

3.2.14 SATA 3Gb/s Drive Connectors

PCIE-H610 PICMG 1.3 CPU Card

CN Label: SATA1, SATA2, SATA3, SATA4 CN Type: CN Location: CN Pinouts:

7-pin SATA drive connector

Figure 3-15

See

Table 3-15

See

The SATA drive connectors can be connected to SATA drives and support up to 3Gb/s data transfer rate.

Page 30

Figure 3-15: SATA 3Gb/s Drive Connector Location

PCIE-H610 PICMG 1.3 CPU Card

Pin Description Pin Description

1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND

Table 3-15: SATA 3Gb/s Drive Connector Pinouts

3.2.15 Serial Port Connectors, RS-232

CN Label: COM1, COM2 CN Type: CN Location: CN Pinouts:

10-pin box header See Figure 3-16 See Table 3-16

Each of these connectors provides RS-232 connections.

Figure 3-16: Serial Port Connector Location

Pin Description Pin Description

1 DATA CARRIER DETECT (DCD) 2 DATA SET READY (DSR) 3 RECE IVE DATA (RXD) 4 REQUEST TO SEND (RTS) 5 TRA NSMIT DATA (TXD) 6 CLEAR TO SEND (CTS) 7 DATA TERMINAL READY (DTR) 8 RING INDICATOR (RI) 9 GND 10 GND

Table 3-16: Serial Port Connector Pinouts

Page 31

3.2.16 Serial Port Connector, RS-422/485

CN Label: COM3

PCIE-H610 PICMG 1.3 CPU Card

CN Type: CN Location: CN Pinouts:

4-pin wafer See Figure 3-17 See Table 3-17

This connector provides RS-422 or RS-485 communications.

Figure 3-17: RS-422/485 Connector Location

Pin Description

1 RXD4222 RXD422+ 3 TXD422+/TXD485+ 4 TXD422-/TXD485-

Table 3-17: RS-422/485 Connector Pinouts

Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9 connector are listed below.

RS-422 Pinouts RS-485 Pinouts

Table 3-18: DB-9 RS-422/485 Pinouts

Page 32

PCIE-H610 PICMG 1.3 CPU Card

3.2.17 SMBus Connector

CN Label: SMBUS_1 CN Type: CN Location: CN Pinouts:

The SMBus (System Management Bus) connector provides low-speed system management communications.

Figure 3-18: SMBus Connector Location

4-pin wafer

Figure 3-18

See

Table 3-19

See

Pin Description

1 +5VS 2 SMB_CLK 3 SMB_DATA 4 GND

Table 3-19: SMBus Connector Pinouts

3.2.18 SPI ROM Connector

CN Label: JSPI1 CN Type: CN Location: CN Pinouts:

The SPI connector is used to flash the BIOS.

8-pin header See Figure 3-19 See Table 3-20

Page 33

Figure 3-19: SPI Connector Location

PCIE-H610 PICMG 1.3 CPU Card

Pin Description Pin Description

1 SPI_VCC 2 GND 3 SPI_CS0 4 SPI_CLK 5 SPI_MISO 6 SPI_MOSI 7 NC 8 NC

Table 3-20: SPI Connector Pinouts

3.2.19 TPM Connector

CN Label: TPM1 CN Type: CN Location: CN Pinouts:

The TPM connector connects to a TPM module.

20-pin header See Figure 3-20 See Table 3-21

Page 34

Figure 3-20: TPM Connector Location

PCIE-H610 PICMG 1.3 CPU Card

Pin Description Pin Description

1 CLK 2 GND 3 ERAME# 4 NC 5 RESRT# 6 +5V 7 AD3 8 AD2 9 +3V 10 AD1 11 AD0 12 GND 13 SMB_CLK 14 SMB_DATA 15 SB3V 16 SERIRQ 17 GND 18 +3V 19 PM_SUS_STAT# 20 DRQ#

Table 3-21: TPM Connector Pinouts

3.2.20 USB Connectors

CN Label: USB1, USB2 CN Type: CN Location: CN Pinouts:

8-pin header See Figure 3-21 See Table 3-22

The USB connectors connect to USB devices. Each pin header provides two USB ports.

Figure 3-21: USB Connector Pinout Locations

Pin Description Pin Description

1 VCC 2 GND 3 DATA- 4 DATA+ 5 DATA+ 6 DATA7 GND 8 VCC

Table 3-22: USB Port Connector Pinouts

Page 35

PCIE-H610 PICMG 1.3 CPU Card

3.3 External Peripheral Interface Connector Panel

The figure below shows the external peripheral interface connector (EPIC) panel. The EPIC panel consists of the following:

Figure 3-22: External Peripheral Interface Connector

3.3.1 Ethernet Connectors

CN Label: CN Type: CN Location: CN Pinouts:

The PCIE-H610 is equipped with two built-in RJ-45 Ethernet controllers. Each controller can connect to the LAN through one RJ-45 LAN connector.

Pin Description Pin Description

1 MDIA3- 5 MDIA2+ 2 MDIA3+ 6 MDIA1+ 3 MDIA1- 7 MDIA04 MDIA2- 8 MDIA0+

Table 3-23: LAN Pinouts

LAN1 and LAN2

RJ-45

Figure 3-22

See

Figure 3-23 and Table 3-23

See

Page 36

Figure 3-23: Ethernet Connector

PCIE-H610 PICMG 1.3 CPU Card

LED Description LED Description

A on: linked

blinking: data is being sent/received

B off: 10 Mb/s

green: 100 Mb/s orange: 1000 Mb/s

Table 3-24: Connector LEDs

3.3.2 USB Connectors

CN Label: CN Type: CN Location: CN Pinouts:

The PCIE-H610 has two external USB 2.0 ports. The ports connect to both USB 2.0 and USB 1.1 devices.

Pin Description

1 VCC

USB_C1 and USB_C2 USB port See Figure 3-22 See Table 3-25

2 DATA3 DATA+ 4 GROUND

Table 3-25: USB Port Pinouts

3.3.3 VGA Connector

CN Label: VGA1 CN Type: CN Location: CN Pinouts:

15-pin Female See Figure 3-22 See Figure 3-24 and Table 3-26

Page 37

PCIE-H610 PICMG 1.3 CPU Card

The VGA connector connects to a monitor that accepts a standard VGA input.

Pin Description Pin Description

1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VGAVCC 10 GND 11 NC 12 DDCDAT 13 HSYNC 14 VSYNC 15 DDCCLK

Table 3-26: VGA Connector Pinouts

Figure 3-24: VGA Connector

Page 38

PCIE-H610 PICMG 1.3 CPU Card

Chapter

4 Installation

Page 39

4.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the PCIE-H610 may result in permanent damage to the PCIE-H610 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components, including the PCIE-H610. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the PCIE-H610 or any other electrical component is handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: - Wearing a simple anti-static wristband can

PCIE-H610 PICMG 1.3 CPU Card

help to prevent ESD from damaging the board.

 Self-grounding:- Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground.

 Use an anti-static pad: When configuring the PCIE-H610, place it on an

anti-static pad. This redu ces the possibility of ESD damaging the PCIE-H610.

 Only handle the edges of the PCB:-: When handling the PCB, hold the PCB

by the edges.

4.2 Installation Considerations

NOTE:

The following installation notices and installation considerations should be read and understood before installation. All installation notices must be strictly adhered to. Failing to adhere to these precautions may lead

Page 40

to severe damage and injury to the person performing the installation.

PCIE-H610 PICMG 1.3 CPU Card

WARNING:

The installation instructions described in this manual should be carefully followed in order to prevent damage to the components and injury to the user.

Before and during the installation please DO the following:

 Read the user manual:

o The user manual provides a complete description of the PCIE-H610

installation instructions and configuration options.

 Wear an electrostatic discharge cuff (ESD):

o Electronic components are easily damaged by ESD. Wearing an ESD cuff

removes ESD from the body and helps prevent ESD damage.

 Place the PCIE-H610 on an anti-static pad:

o When installing or configuring the motherboard, place it on an anti-static

pad. This helps to prevent potential ESD damage.

 Turn all power to the PCIE-H610 off:

o When working with the PCIE-H610, make sure that it is disconnected

from all power supplies and that no electricity is being fed into the system.

Before and during the installation of the PCIE-H610 DO NOT:

 Remove any of the stickers on the PCB board. These stickers are required for

warranty validation.

 Use the product before verifying all the cables and power connectors are

properly connected.

 Allow screws to come in contact with the PCB circuit, connector pins, or its

components.

Page 41

4.2.1 Socket LGA1155 CPU Installation

WARNING:

CPUs are expensive and sensitive components. When installing the CPU please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed.

DO NOT touch the pins at the bottom of the CPU. When handling the CPU, only hold it on the sides.

To install the CPU, follow the steps below.

PCIE-H610 PICMG 1.3 CPU Card

Step 1: Disengage the load lever by pressing the lever down and slightly outward to

clear the retention tab. Fully open the lever. See

Figure 4-1: Disengage the CPU Socket Load Lever

Step 2: Open the socket and remove the protective cover. The black protective

Figure 4-1.

Page 42

cover can be removed by pulling up on the tab labeled "Remove". See

Figure 4-2.

PCIE-H610 PICMG 1.3 CPU Card

Figure 4-2: Remove Protective Cover

Step 3: Inspect the CPU socket. Make sure there are no bent pins and make sure the

socket contacts are free of foreign material. If any debris is found, remove it with compressed air.

Step 4: Orientate the CPU properly. The contact array should be facing the CPU

socket.

Step 5: Correctly position the CPU. Match the Pin 1 mark with the cut edge on the

CPU socket.

Step 6: Align the CPU pins. Locate pin 1 and the two orient ation notches on the CPU.

Carefully match the two orientation notches on the CPU with the socket alignment keys.

Step 7: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are

properly aligned, the CPU should slide into the CPU socket smoothly. See

Figure 4-3.

Page 43

Figure 4-3: Insert the Socket LGA1155 CPU

Step 8: Close the CPU socket. Close the load plate and pull the load lever back a little

PCIE-H610 PICMG 1.3 CPU Card

to have the load plate be able to secure to the knob. Engage the load lever by pushing it back to its original position ( resistance, but will not require extreme pressure.

Figure 4-4: Close the Socket LGA1155

Step 9: Connect the 12 V power to the board. Connect the 12 V power from the power

Figure 4-4). There will be some

Page 44

supply to the board.

PCIE-H610 PICMG 1.3 CPU Card

4.2.2 Socket LGA1155 Cooling Kit Installation

The cooling kit can be bought from IEI. The cooling kit has a heatsink and fan.

WARNING:

Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the heat sink. The thermal paste between the CPU and the heat sink is important for optimum heat dissipation.

To install the cooling kit, follow the instructions below.

Step 1: A cooling kit bracket is pre-installed on the rear of the motherboard. See

4-5.

Figure 4-5: Cooling Kit Support Bracket

Step 2: Place the cooling kit onto the socket LGA1155 CPU. Make sure the CPU

cable can be properly routed when the cooling kit is installed.

Step 3: Mount the cooling kit. Gently place the cooling kit on top of the CPU. Make

Figure

sure the four threaded screws on the corners of the cooling kit properly pass through the holes of the cooling kit bracket.

Step 4: Secure the cooling kit by fastening the four retention screws of the cooling kit.

Page 45

Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector

on the PCIE-H610. Carefully route the cable and avoid heat generating chips and fan blades.

4.2.3 DIMM Installation

To install a DIMM, please follow the steps below and refer to Figure 4-6.

PCIE-H610 PICMG 1.3 CPU Card

Figure 4-6: DIMM Installation

Step 1: Open the DIMM socket handles. Open the two handles outwards as far as

they can. See

Step 2: Align the DIMM with the socket. Align the DIMM so the notch on the memory

lines up with the notch on the memory socket. See

Step 3: Insert the DIMM. Once aligned, press down until the DIMM is properly seated.

Clip the two handles into place. See

Step 4: Removing a DIMM. To remove a DIMM, push both handles outward. The

memory module is ejected by a mechanism in the socket.

Figure 4-6.

Page 46

PCIE-H610 PICMG 1.3 CPU Card

4.3 Jumper Settings

NOTE:

A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper.

The hardware jumpers must be set before installation. Jumpers are shown in Table 4-1.

Description Label Type

AT/ATX power select JATX_AT1 2-pin header Clear CMOS jumper J_CMOS1 3-pin header Wake-on LAN JLAN_PWR1 6-pin header

Table 4-1: Jumpers

4.3.1 AT/ATX Power Select Jumper

Jumper Label: JATX_AT1 Jumper Type: Jumper Settings: Jumper Location:

2-pin header See Table 4-2 See Figure 4-7

Page 47

The AT/ATX Power Select jumper specifies the systems power mode as AT or ATX.

Setting Description

Closed ATX power (Default) Open AT power

PCIE-H610 PICMG 1.3 CPU Card

Table 4-2: AT/ATX Power Mode Jumper Settings

Figure 4-7: AT/ATX Power Mode Jumper Location

4.3.2 Clear CMOS Jumper

Jumper Label: J_CMOS1 Jumper Type: Jumper Settings: Jumper Location:

3-pin header See Table 4-3 See Figure 4-8

Page 48

To reset the BIOS, move the jumper to the "Clear BIOS" position for 3 seconds or more, and then move back to the default position.

Setting Description

Short 1-2 Normal Short 2-3 Clear BIOS

Table 4-3: Clear BIOS Jumper Settings

PCIE-H610 PICMG 1.3 CPU Card

Figure 4-8: Clear BIOS Jumper Location

4.3.3 Wake-on LAN Jumper

CN Label: JLAN_PWR1 CN Type: CN Location: CN Pinouts:

The Wake-on LAN jumper allows the user to enable or disable the Wake-on LAN (WOL) function.

Setting Description

Short 1-3 Enable LAN 2 Wake-on LAN (Default) Short 2-4 Enable LAN 1 Wake-on LAN (Default) Short 3-5 Disable LAN 2 Wake-on-LAN Short 4-6 Disable LAN 1 Wake-on LAN

Table 4-4: Wake-on LAN Jumper Settings

6-pin header See Figure 4-9 See Table 4-4

Figure 4-9: Wake-on LAN Jumper Location

Page 49

Pin Description Pin Description

PCIE-H610 PICMG 1.3 CPU Card

1 3 5

+3.3V_DUAL +V3.3LAN2 +3.3V

Table 4-5: Wake-on LAN Jumper Pinouts

4.4 Chassis Installation

4.4.1 Airflow

WARNING:

Airflow is critical to the cooling of the CPU and other onboard components. The chassis in which the PCIE-H610 must have air vents to allow cool air to move into the system and hot air to move out.

The PCIE-H610 must be installed in a chassis with ventilation holes on the sides allowing

2 4 6

+3.3V_DUAL +V3.3LAN1 +3.3V

airflow to travel through the heat sink surface. In a system with an individual power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface.

4.4.2 CPU Card Installation

To install the CPU card onto the backplane, carefully align the CPU card edge connector with the CPU card socket on the backplane. To do this, please refer to the reference material that came with the backplane. Next, secure the CPU card to the chassis. To do this, please refer to the reference material that came with the chassis.

4.5 Internal Peripheral Device Connections

This section outlines the installation of peripheral devices to the onboard connectors.

Page 50

PCIE-H610 PICMG 1.3 CPU Card

4.5.1 Dual RS-232 Cable with Slot Bracket

The dual RS-232 cable slot connector consists of two connectors attached to two independent cables. Each cable is then attached to a D-sub 9 male connector that is mounted onto a slot. To install the dual RS-232 cable, please follow the steps below.

Step 1: Locate the connectors. The locations of the RS-232 connectors are shown in

Chapter 3.

Step 2: Insert the cable connectors. Insert one conne ctor into each serial port box

headers ( connector can only be installed in one direction.

Figure 4-10: Dual RS-232 Cable Installation

Figure 4-10). A key on the front of the cable connectors ensures the

Step 3: Secure the bracket. The dual RS-232 connector has two D-sub 9 male

connectors secured on a bracket. To secure the bracket to the chassis please refer to the reference material that came with the chassis.

Page 51

PCIE-H610 PICMG 1.3 CPU Card

4.5.2 DVI-D/USB Kit Installation (DVI Model Only)

The DVI-D/USB kit, consisting of one DVI-D and four USB ports, connects to the DVI-D and USB connectors on the PCIE-H610. To install the DVI-D/USB kit, please follow the steps below.

Step 1: Connect the cables to the DVI-D/USB kit. Conn ect the included cables to the

DVI-D/USB kit.

Step 2: Connect the cables to the board. Connect the othe r ends of the included

cables to the board.

Page 52

Figure 4-11: DVI-D/USB Kit Installation

Step 3: Mount the DVI-D/USB kit onto the chassis. Once the DVI-D/USB kit is

connected to the board, secure the DVI-D/USB kit bracket to the system chassis.

PCIE-H610 PICMG 1.3 CPU Card

4.5.3 SATA Drive Connection

The PCIE-H610 is shipped with four SATA drive cables. To connect the SATA drives to the connectors, please follow the steps below.

Step 1: Locate the connectors. The locations of the SATA drive connectors are shown

in Chapter 3.

Step 2: Insert the cable connector. Insert the cable conne ctor into the on-board SATA

drive connector until it clips into place. See

Figure 4-12.

Figure 4-12: SATA Drive Cable Connection

Step 3: Connect the cable to the SAT A disk. Connect the connector on the other end

of the cable to the connector at the back of the SATA drive. See

Step 4: Connect the SATA power cable (optional). Connect the SATA power

connector to the back of the SATA drive. See

Figure 4-13.

Page 53

PCIE-H610 PICMG 1.3 CPU Card

Figure 4-13: SATA Power Drive Connection

4.5.4 USB Cable (Dual Port) with Slot Bracket

The PCIE-H610 is shipped with a dual port USB 2.0 cable. To connect the USB cable connector, please follow the steps below.

Step 1: Locate the connectors. The locations of the USB connectors are shown in

Chapter 3.

WARNING:

If the USB pins are not properly aligned, the USB device can burn out.

Step 2: Align the connectors. The cable has two connectors. Correctly align pin 1on

Page 54

each cable connector with pin 1 on the PCIE-H610 USB connector.

PCIE-H610 PICMG 1.3 CPU Card

Step 3: Insert the cable connectors. Once the cable connectors are properly aligned

with the USB connectors on the PCIE-H610, connect the cable connectors to the on-board connectors. See

Figure 4-14.

Figure 4-14: Dual USB Cable Connection

Step 4: Attach th e bracket to the chassis. The USB 2.0 connectors are attached to a

bracket. To secure the bracket to the chassis please refer to the installation instructions that came with the chassis.

4.6 External Peripheral Interface Connection

This section describes connecting devices to the external connectors on the PCIE-H610.

4.6.1 LAN Connection

There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection to an external network. To connect a LAN cable with an RJ-45 connector, please follow the instructions below.

Page 55

Step 1: Locate the RJ-45 connectors. The locations of the RJ-45 connectors are

shown in Chapter 3.

Step 2: Align the connectors. Align the RJ-45 connector on the LAN ca ble with one of

PCIE-H610 PICMG 1.3 CPU Card

the RJ-45 connectors on the PCIE-H610. See

Figure 4-15: LAN Connection

Figure 4-15.

Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN

cable RJ-45 connector into the on-board RJ-45 connector.

4.6.2 USB Device Connection (Single Connector)

There is one external USB 2.0 connector. The connector is perpendicular to the PCIE-H610. To connect a USB 2.0 or USB 1.1 device, please follow the instructions below.

Step 1: Located the USB connector. The location of the USB connector is shown in

Chapter 3.

Step 2: Align the connectors. Align the USB device connector with the connector on

Figure 4-16.

Page 56

the PCIE-H610. See

PCIE-H610 PICMG 1.3 CPU Card

Figure 4-16: USB Device Connection

Step 3: Insert the device connector. Once aligned, gently insert the USB device

connector into the on-board connector.

4.6.3 VGA Monitor Connection

The PCIE-H610 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the PCIE-H610, please follow the instructions below.

Step 1: Locate the female DB-15 connector. The location of the female DB-15

connector is shown in Chapter 3.

Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen

cable with the female DB-15 connector on the external peripheral interface.

Step 3: Insert the VGA co nnector. Once the connectors are properly aligned with the

insert the male connector from the VGA screen into the female connector on the PCIE-H610. See

Figure 4-17.

Page 57

Figure 4-17: VGA Connector

PCIE-H610 PICMG 1.3 CPU Card

Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA

monitor to the external interface by tightening the two retention screws on either side of the connector.

Page 58

PCIE-H610 PICMG 1.3 CPU Card

Chapter

5 BIOS

Page 59

5.1 Introduction

The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed.

NOTE:

Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.

5.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.

PCIE-H610 PICMG 1.3 CPU Card

1. Press the DEL or F2 key as soon as the system is turned on or

2. Press the DEL or F2 key when the “Press DEL or F2 to enter SETUP” message appears on the screen. 0.

If the message disappears before the DEL or F2 key is pressed, restart the computer and try again.

5.1.2 Using Setup

Use the arrow keys to highlight items, press ENTER to select, use the PageUp and PageDown keys to change entries, press F1 for help and press E keys are shown in the following table.

Key Function

Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the item on the left hand side

SC to quit. Navigation

Page 60

Right arrow Move to the item on the right hand side + Increase the numeric value or make changes

- Decrease the numeric value or make changes

PCIE-H610 PICMG 1.3 CPU Card

Key Function

Page Up key Increase the numeric value or make changes Page Dn key Decrease the numeric value or make changes Esc key Main Menu – Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu

F1 General help, only for St atus Page Setup Menu and Option

Page Setup Menu F2 Previous values F3 Load optimized defaults F4 Save changes and Exit BIOS

Table 5-1: BIOS Navigation Keys

5.1.3 Getting Help

When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press E the F1 key again.

5.1.4 Unable to Reboot after Configuration Changes

If the computer cannot boot after changes to the system configuration is made, CMOS defaults. Use the jumper described in Chapter 4.

5.1.5 BIOS Menu Bar

The menu bar on top of the BIOS screen has the following main items:

 Main – Changes the basic system configuration.  Advanced – Changes the advanced system settings.  Chipset – Changes the chipset settings.  Boot – Changes the system boot configuration.

SC or

 Security – Sets User and Supervisor Passwords.  Save & Exit – Selects exit options and loads default settings

Page 61

The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above.

PCIE-H610 PICMG 1.3 CPU Card

5.2 Main

The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information.

Main Advanced Chipset Boot Security Save & Exit

BIOS Information BIOS Vendor American Megatrends Core Version 4.6.4.0 0.03 Compliency UEFI 2.0 Project Version B222AR06.ROM Build Date and Time 01/02/2012 14:17:42

Memory Information Total Memory 1024 MB (DDR3 1333)

System Date [Thu 02/02/2012] System Time [15:10:27]

Access Level Administrator

Set the Date. Use Tab to switch between Data elements.

----------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 1: Main

Î System Overvi ew

The BIOS Information lists a brief summary of the BIOS. The fields in BIOS Information cannot be changed. The items shown in the system overview include:

 BIOS Vendor: Installed BIOS vendor  Core Version: Current BIOS version  Project Version: the bo ard version  Build Date and Time: Date and time the current BIOS version was made

Î Memory Information

The Memory Information lists a brief summary of the on-board memory. The fields in Memory Information cannot be changed.

 Total Memory: Displays the auto-detected system memory size and type.

Page 62

PCIE-H610 PICMG 1.3 CPU Card

The System Overview field also has two user configurable fields:

Î System Date [xx/xx/xx]

Use the System Date option to set the system date. Manually enter the day, month and year.

Î System Time [xx:xx:xx]

Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.

5.3 Advanced

Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus:

WARNING!

Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.

Main Advanced Chipset Boot Security Save & Exit

> ACPI Settings > Trusted Computing > CPU Configuration > SATA Configuration > Intel TXT(LT) Configuration > USB Configuration > Super IO Configuration > H/M Monitor > Serial Port Console Redirection > iEi Feature

System ACPI Parameters

----------------------

ÆÅ

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

: Select Screen

BIOS Menu 2: Advanced

Page 63

PCIE-H610 PICMG 1.3 CPU Card

5.3.1 ACPI Settings

The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and Power Interface (ACPI) options.

Advanced

ACPI Settings

ACPI Sleep State [S1 (CPU Stop Clock)]

elect the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.

----------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 3: ACPI Configuration

Î ACPI Sleep State [S1 (CPU Stop Clock)]

Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used.

S1 (CPU Stop Clock)

S3 (Suspend to RAM)

DEFAULT

The system enters S1 (POS) sleep state. The system appears off. The CPU is stopped; RAM is refreshed; the system is running in a low power mode.

The caches are flushed and the CPU is powered off. Power to the RAM is maintained. The computer returns slower to a working state, but more power is saved.

Page 64

PCIE-H610 PICMG 1.3 CPU Card

5.3.2 Trusted Computing

Use the Trusted Computing menu (BIOS Menu 4) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM).

Advanced

TPM Configuration TPM SUPPORT [Disable]

Current TPM Status Information

NO TPM Hardware

nables or Disables TPM support. O.S. will not show TPM. Reset of platform is required.

----------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 4: TPM Configuration

Î TPM Support [Disable]

Use the TPM Support option to configure support for the TPM.

Disable DEFAULT

Enable

TPM support is disabled. TPM support is enabled.

5.3.3 CPU Configuration

Use the CPU Configuration menu (BIOS Menu 5) to enter the CPU Information submenu or enable Intel Virtualization Technology.

Page 65

Advanced

CPU Configuration

> CPU Information

Intel Virtualization Technology [Disabled]

BIOS Menu 5: CPU Configuration

PCIE-H610 PICMG 1.3 CPU Card

Socket specific CPU Information

----------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Î Intel Vi rtualization Technology [Disabled]

Use the Intel Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel® Virtualization technology allows several OSs to run on the same system at the same time.

Disabled DEFAULT

Enabled

Disables Intel Virtualization Technology.

Enables Intel Virtualization Technology.

5.3.3.1 CPU Information

Use the CPU Information submenu (BIOS Menu 6) to view detailed CPU specifications and configure the CPU.

Page 66

PCIE-H610 PICMG 1.3 CPU Card

Advanced

CPU Information

Intel(R) Core(TM) i5-2400 CPU 0 @ 3.10GHz CPU Signature 206a7 Microcode Patch 14 Max CPU Speed 3100 MHz Min CPU Speed 1600 MHz Processor Cores 4 Intel HT Technology Not Supported Intel VT-x Technology Supported Intel SMX Technology Supported

L1 Data Cache 32 kB x 2 L1 Code Cache 32 kB x 2 L2 Cache 256 kB x 2 L3 Cache 6144 kB

BIOS Menu 6: CPU Configuration

----------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

The CPU Configuration menu (

 Processor Type: Lists the brand name of the CPU being used  CPU Signature: Lists the CPU signature value.  Microcode Patch: Lists the microcode patch being used.  Max CPU Speed: Lists the maximum CPU processing speed.  Min CPU Speed: Lists the minimum CPU processing speed.  Processor Cores: Lists the number of the processor core  Intel HT Technology: Indicates if Intel HT Technology is supported by the

CPU.

 Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the

CPU.

 Intel SMX Technology: Indicates if Intel SMX Technology is supported by the

CPU.

 L1 Data Cache: Lists the amount of data storage space on the L1 cache.  L1 Code Cache: Lists the amount of code storage space on the L1 cache.  L2 Cache: Lists the amount of storage space on the L2 cache.

BIOS Menu 6) lists the following CPU details:

 L3 Cache: Lists the amount of storage space on the L3 cache.

Page 67

PCIE-H610 PICMG 1.3 CPU Card

5.3.4 SATA Configuration

Use the SATA Configuration menu (BIOS Menu 7) to change and/or set the configuration of the SATA devices installed in the system.

Advanced

SATA Configuration

SATA Mode [IDE Mode] Serial-ATA Controller 0 [Compatible] Serial-ATA Controller 1 [Enhanced]

SATA Port0 Not Present

SATA Port1 Not Present

SATA Port4 Not Present

SATA Port5 Not Present

(1) IDE Mode. (2) AHCI Mode. (3) RAID Mode.

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 7: SATA Configuration

Î SATA Mode [IDE Mode]

Use the SATA Mode option to configure SATA devices as normal IDE devices.

Disabled

IDE Mode DEFAULT

Î Serial-ATA Controller 0 [Compatible]

Use the Serial-ATA Controller 0 option to configure the serial ATA controller 0.

Î Î

Disabled

Enhanced

Disables the on-board ATA controller. Configures the on-board ATA controller to be in

Disables SATA devices. Configures SATA devices as normal IDE device.

Enhanced mode. In this mode, IDE channels and SATA channels are separated. This mode supports up to 6 storage devices. Some legacy OS do not support this

Page 68

mode.

PCIE-H610 PICMG 1.3 CPU Card

Compatible D

Î Serial-ATA Controller 1 [Enhanced]

Use the Serial-ATA Controller 1 option to configure the serial ATA controller 1.

Disabled

Enhanced D

EFAULT

Disables the on-board ATA controller.

EFAULT

Configures the on-board ATA controller to be in compatible mode. In this mode, a SATA channel will replace one of the IDE channels. This mode supports up to 4 storage devices.

Configures the on-board ATA controller to be in Enhanced mode. In this mode, IDE channels and SATA channels are separated.

5.3.5 Intel TXT(LT) Configuration

Use the Intel TXT(LT) Configuration menu to configure Intel Trusted Execution Technology support.

Advanced

Intel Trusted Execution Technology Configuration

Intel TXT support only can be enabled/disabled if SMX is enabled. VT and VT-d support must also be enabled prior to TXT.

Secure Mode Extensons (SMX) Enabled

Intel TXT(LT) Support [Disabled]

BIOS Menu 8: Intel TXT(LT) Configuration

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Page 69

PCIE-H610 PICMG 1.3 CPU Card

5.3.6 USB Configuration

Use the USB Configuration menu (BIOS Menu 9) to read USB configuration information and configure the USB settings.

Advanced

USB Configuration

USB Devices: 2 Hubs

USB Support [Enabled] Legacy USB Support [Enabled]

USB Support Parameters

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 9: USB Configuration

Î USB Devices

The USB Devices Enabled field lists the USB devices that are enabled on the system

Î USB Support [Enabled]

Use the USB Support option to enable or disable USB support on the system.

Disabled

Enabled DEFAULT

Î Legacy USB Support [Enabled]

Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

USB support disabled USB support enabled

Page 70

does not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB

PCIE-H610 PICMG 1.3 CPU Card

keyboard can control the system even when there is no USB driver loaded onto the system.

Enabled DEFAULT

Disabled

Legacy USB support enabled Legacy USB support disabled

5.3.7 Super IO Configuration

Use the Super IO Configuration menu (BIOS Menu 10) to set or change the configurations for the FDD controllers, parallel ports and serial ports.

Advanced

Super IO Configuration

Super IO Chip Fintek F81866

> Floppy Disk Controller Configuration > Serial Port 1 Configuration > Serial Port 2 Configuration > Serial Port 3 Configuration > Serial Port 6 Configuration > Parallel Port Configuration

Power Saving Function [Disabled]

Set Parameters of Floppy Disk Controller (FDC)

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 10: Super IO Configuration

Î Power Saving Function [Disabled]

Use the Power Saving Function BIOS option to enable or reduce power consumption in the S5 state. When enabled, the system can only be powered-up using the power button.

Disabled DEFAULT

Enabled

Power Saving Function support disabled Power Saving Function support enabled

Page 71

PCIE-H610 PICMG 1.3 CPU Card

5.3.7.1 Floppy Disk Controller Configuration

Use the Floppy Disk Controller Configuration menu (BIOS Menu 12) to configure the floppy disk controller.

Advanced

Floppy Disk Controller Configuration

Floppy Disk Controller [Enabled]

Device Settings Reset Required

Change Settings [Auto] Device Mode [Read Write]

nable or Disable Floppy Disk Controller

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 11: Serial Port n Configuration Menu

Î Floppy Disk Controller [Enabled]

Use the Floppy Disk Controller option to enable or disable the floppy disk controller.

Disabled

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the super IO device address and interrupt address.

Auto DEFAULT

IO=3F8h;

Floppy disk controller disabled Floppy disk controller enabled

The super IO device address and interrupt address are automatically detected.

The super IO device address is 3F8h, interrupt

IRQ=6; DMA=2

Page 72

address is IRQ6 and DMA channel is DMA2

PCIE-H610 PICMG 1.3 CPU Card

Î Device Mode [Read Write]

Use the Device Mode option to select the floppy disk controller mode.

Rear Write DEFAULT

Write Portect

Selects this option for normal operation. Selects this mode for read only operation.

5.3.7.2 Serial Port n Configuration

Use the Serial Port n Configuration menu (BIOS Menu 12) to configure the serial port n.

Advanced

Serial Port n Configuration

Serial Port [Enabled]

Device Settings IO=3F8h; IRQ=4

Change Settings [Auto]

nable or Disable Serial Port (COM)

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 12: Serial Port n Configuration Menu

5.3.7.2.1 Serial Port 1 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled

Enabled DEFAULT

Disable the serial port Enable the serial port

Page 73

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

PCIE-H610 PICMG 1.3 CPU Card

Auto DEFAULT

IO=3F8h; IRQ=4

IO=3F8h; IRQ=3, 4

IO=2F8h; IRQ=3, 4

IO=2C0h; IRQ=3, 4

IO=2C8h; IRQ=3, 4

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 3F8h and the interrupt address is IRQ4

Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3, 4

Serial Port I/O port address is 2C0h and the interrupt address is IRQ3, 4

Serial Port I/O port address is 2C8h and the interrupt address is IRQ3, 4

5.3.7.2.2 Serial Port 2 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Auto DEFAULT

Page 74

Disable the serial port Enable the serial port

The serial port IO port address and interrupt address are automatically detected.

PCIE-H610 PICMG 1.3 CPU Card

IO=2F8h; IRQ=3

IO=3F8h; IRQ=3, 4

IO=2F8h; IRQ=3, 4

IO=2C0h; IRQ=3, 4

IO=2C8h; IRQ=3, 4

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3

Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3, 4

Serial Port I/O port address is 2C0h and the interrupt address is IRQ3, 4

Serial Port I/O port address is 2C8h and the interrupt address is IRQ3, 4

5.3.7.2.3 Serial Port 3 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Auto DEFAULT

IO=2E8h; IRQ=10

IO=3E8h; IRQ=10, 11

IO=2E8h; IRQ=10, 11

Disable the serial port Enable the serial port

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 2E8h and the interrupt address is IRQ10

Serial Port I/O port address is 3E8h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2E8h and the interrupt address is IRQ10, 11

Page 75

PCIE-H610 PICMG 1.3 CPU Card

IO=2D0h; IRQ=10, 11

IO=2D8h; IRQ=10, 11

Î Device Mode [RS422/485 ]

Use the Device Mode option to select the serial port mode.

RS422/485 DEFAULT

5.3.7.2.4 Serial Port 6 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled

Serial Port I/O port address is 2D0h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2D8h and the interrupt address is IRQ10, 11

Enables serial port RS-422/485 support.

Disable the serial port

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Auto DEFAULT

IO=2E0h; IRQ=10

IO=2C0h; IRQ=10, 11

IO=2C8h; IRQ=10, 11

Enable the serial port

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 2E0h and the interrupt address is IRQ10

Serial Port I/O port address is 2C0h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2C8h and the interrupt address is IRQ10, 11

Page 76

PCIE-H610 PICMG 1.3 CPU Card

IO=2D0h; IRQ=10, 11

IO=2D8h; IRQ=10, 11

IO=2E0h; IRQ=10, 11

Serial Port I/O port address is 2D0h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2D8h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2E0h and the interrupt address is IRQ10, 11

5.3.7.3 Parallel Port Configuration

Use the Parallel Port Configuration menu (BIOS Menu 12) to configure the serial port n.

Advanced

Parallel Port Configuration

Parallel Port [Enabled]

Device Settings IO=378h; IRQ=7

Change Settings [Auto] Device Mode [Printer Mode]

Enable or Disable Parallel Port (LPT/LPTE)

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 13: Parallel Port Configuration Menu

Î Parallel Port [Enabled]

Use the Parallel Port option to enable or disable the parallel port.

Disabled

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the parallel port IO port address and interrupt address.

Disable the parallel port Enable the parallel port

Page 77

PCIE-H610 PICMG 1.3 CPU Card

Auto DEFAULT

IO=378h; IRQ=7

IO=278h; IRQ=7

IO=3BCh; IRQ=7

Î Device Mode [Printer Mode]

Use the Device Mode option to select the mode the parallel port operates in. Configuration options are listed below.

 Printer Mode Default  SPP Mode

The parallel port IO port address and interrupt address are automatically detected.

Parallel Port I/O port address is 378h and the interrupt address is IRQ7

Parallel Port I/O port address is 278h and the interrupt address is IRQ7

Parallel Port I/O port address is 3BCh and the interrupt address is IRQ7

 EPP-1.9 and SPP Mode  EPP-1.7 and SPP Mode  ECP Mode  ECP and EPP 1.9 Mode  ECP and EPP 1.7 Mode

5.3.8 H/W Monitor

The H/W Monitor menu (BIOS Menu 14) contains the fan configuration submenus and displays operating temperature, fan speeds and system voltages.

Page 78

PCIE-H610 PICMG 1.3 CPU Card

Advanced

PC Health Status

CPU Temperature :+54 C SYS Temperature :+35 C CPU FAN Speed :2255 RPM VCC3V :+3.344 V V_core :+1.248 V +1.05V :+1.048 V VDDR :+1.632 V VSB3V :+3.392 V VBAT :+3.120 V 5VSB :+4.920 V

> FAN 1 Configuration

BIOS Menu 14: H/W Monitor

Smart FAN Configuration

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Î PC Health Status

The following system parameters and values are shown. The system parameters that are monitored are:

 System Temperatures:

o CPU Temperature o System Temperature

 Fan Speeds:

o CPU Fan Speed

 Voltages:

o VCC3V o V_core o +1.05V o VDDR o VSB3V o VBAT o 5VSB

Page 79

PCIE-H610 PICMG 1.3 CPU Card

5.3.8.1 FAN 1 Configuration

Use the FAN 1 Configuration submenu (BIOS Menu 15) to configure fan 1 temperature and speed settings.

Advanced

PC Health Status

CPU Smart Fan control [Auto by RPM] Target Temp. Sensor [CPU Temperature] Temperature Bound 1 60 Temperature Bound 2 50 Temperature Bound 3 40 Temperature Bound 4 30 Segment 1 Speed (%) 100 Segment 2 Speed (%) 85 Segment 3 Speed (%) 70 Segment 4 Speed (%) 60 Segment 5 Speed (%) 50 Full Speed Count 3000

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 15: FAN 1 Configuration

Î CPU Smart Fan control [Auto by RPM]

Use the CPU Smart Fan control option to configure the CPU Smart Fan.

Auto by RPM DEFAULT

Auto by Duty-Cycle

Manual by RPM

Manual by Duty-Cycle

The fan adjusts its speed using Auto by RPM settings

The fan adjusts its speed using Auto by Duty-Cycle settings

The fan spins at the speed set in Manual by RPM settings

The fan spins at the speed set in Manual by Duty Cycle settings

Î Target Temp. Sensor [CPU Temperature]

Use the Target Temp. Sensor option to set the target CPU temperature.

Page 80

PCIE-H610 PICMG 1.3 CPU Card

CPU Temperature

System Temperature1

System Temperature2

Î Temperature Bound n

Use the + or – key to change the fan Temperature Bound n value. Enter a decimal number between 0 and 127.

Î Segment n S peed (%)

Use the + or – key to change the fan Segment n Speed value in percentage. Enter a decimal number between 0 and 100.

DEFAULT

Sets the target temperature sensor to the CPU temperature.

Sets the target temperature sensor to the System Temperature1 setting.

Sets the target temperature sensor to the System Temperature2 setting.

Î Full Speed Count

Use the + or – key to change the fan Full Speed Count value. Enter a decimal number between 500 and 15000.

5.3.9 Serial Port Console Redirection

The Serial Port Console Redirection menu (BIOS Menu 16) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port.

Page 81

Advanced

COM1

Console Redirection [Disabled]

> Console Redirection Settings

COM2

Console Redirection [Disabled]

> Console Redirection Settings

BIOS Menu 16: Serial Port Console Redirection

PCIE-H610 PICMG 1.3 CPU Card

Console Redirection Enable or Disable

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Î Console Redirection [Disabled]

Use Console Redirection option to enable or disable the console redirection fun ction.

Disabled DEFAULT

Enabled

Î Terminal Type [ANSI]

Use the Terminal Type option to specify the remote terminal type.

VT100

VT100+

VT-UTF8

ANSI DEFAULT

Î Bits per second [115200]

Disabled the console redirection function Enabled the console redirection function

The target terminal type is VT100 The target terminal type is VT100+ The target terminal type is VT-UTF8 The target terminal type is ANSI

Page 82

Use the Bits per second option to specify the serial port transmission speed. The speed must match the other side. Long or noisy lines may require lower speeds.

PCIE-H610 PICMG 1.3 CPU Card

9600

19200

38400

57600

115200 DEFAULT

Î Data Bits [8]

Use the Data Bits option to specify the number of data bits.

8 DEFAULT

Î Parity [None]

Use the Parity option to specify the parity bit that can be sent with the data bits for

Sets the serial port transmission speed at 9600. Sets the serial port transmission speed at 19200. Sets the serial port transmission speed at 38400. Sets the serial port transmission speed at 57600. Sets the serial port transmission speed at 115200.

Sets the data bits at 7. Sets the data bits at 8.

detecting the transmission errors.

None DEFAULT

Even

Odd

Mark

Space

Î Stop Bits [1]

Use the Stop Bits option to specify the number of stop bits used to indicate the end of a serial data packet. Communication with slow devices may require more than 1 stop bit.

No parity bit is sent with the data bits. The parity bit is 0 if the number of ones in the data

bits is even. The parity bit is 0 if the number of ones in the data

bits is odd. The parity bit is always 1. This option does not

provide error detection. The parity bit is always 0. This option does not

provide error detection.

Page 83

PCIE-H610 PICMG 1.3 CPU Card

1 DEFAULT

Î Flow Control [None]

Use the Flow Control option to report the flow control method for the console redirection application.

None DEFAULT

Hardware RTS/CTS

Sets the number of stop bits at 1. Sets the number of stop bits at 2.

No control flow. Hardware is set as the console redirection.

5.3.10 iEi Feature

Use the iEi Feature menu (BIOS Menu 17) to configure One Key Recovery function.

Advanced

iEi Feature

Auto Recovery Function [Disabled]

Auto Recovery Function Reboot and recover system automatically within 10 min, when OS

rashes. Please install Auto Recovery API

ervice before enabling this function.

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 17: IEI Feature

Page 84

PCIE-H610 PICMG 1.3 CPU Card

Î Auto Recovery Function [Disabled]

Use the Auto Recovery Function BIOS option to enable or disable the auto recovery function of the IEI One Key Recovery.

Disabled DEFAULT

Enabled

Auto recovery function disabled Auto recovery function enabled

5.4 Chipset

Use the Chipset menu (BIOS Menu 18) to access the Northbridge, Southbridge, Integrated Graphics, and ME Subsystem configuration menus.

WARNING!

Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.

Main Advanced Chipset Boot Security Save & Exit

> North Bridge > South Bridge > Integrated Graphics

North Bridge Parameters

---------------------

ÆÅ

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

: Select Screen

BIOS Menu 18: Chipset

Page 85

PCIE-H610 PICMG 1.3 CPU Card

5.4.1 Northbridge Configuration

Use the North Bridge menu (BIOS Menu 19) to configure the Northbridge chipset.

Chipset

Memory Information

Total Memory 1024 MB (DDR3 1333)

Memory Slot0 1024 MB (DDR3 1333) Memory Slot2 0 MB (DDR3 1333)

Initate Graphic Adapter [PEG(PCI)/IGD] IGD Memory [64M]

VT-d [Disabled]

Select which graphics

ontroller to use as the primary boot device.

---------------------

ÆÅ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 19:Northbridge Chipset Configuration

Î Initiate Graphic Adapter [PEG(PCI)/IGD]

Use the Initiate Graphic Adapter option to select the graphics controller used as the primary boot device. Select either an integrated graphics controller (IGD) or a combination of PCI graphics controller, a PCI express (PEG) controller or an IGD. Configuration options are listed below:

 IGD  PEG(PCI)/IGD D

Î IGD Memory [64M]

Use the IGD Memory option to specify the amount of system memory that can be used by the internal graphics device.

Disable

EFAULT

32M

64M DEFAULT

Page 86

32 MB of memory used by internal graphics device 64 MB of memory used by internal graphics device

PCIE-H610 PICMG 1.3 CPU Card

96M

128M

160M

192M

224M

256M

288M

320M

96 MB of memory used by internal graphics device 128 MB of memory used by internal graphics

device 160 MB of memory used by internal graphics

device 192 MB of memory used by internal graphics

device 224 MB of memory used by internal graphics

device 256 MB of memory used by internal graphics

device 288 MB of memory used by internal graphics

device 320 MB of memory used by internal graphics

352M

384M

416M

448M

480M

512M

device 352 MB of memory used by internal graphics

device 384 MB of memory used by internal graphics

device 416 MB of memory used by internal graphics

device 448 MB of memory used by internal graphics

device 480 MB of memory used by internal graphics

device 512 MB of memory used by internal graphics

device

Page 87

IEI Technology PCIE-H610 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Introduction

1.1 Introduction

1.2 Model Variations

1.3 Features

1.4 Connectors

1.5 Dimensions

1.6 Data Flow

1.7 Technical Specifications

2 Packing List

2.1 Anti-static Precautions

2.2 Unpacking Precautions

2.3 Packing List

2.4 Optional Items

3 Connectors

3.1 Peripheral Interface Connectors

3.1.1 PCIE-H610 Layout

3.1.2 Peripheral Interface Connectors

3.1.3 External Interface Panel Connectors

3.2 Internal Peripheral Connectors

3.2.1 Audio Kit Connector

3.2.2 Battery Connector

3.2.3 CPU Power Input Connector

3.2.4 DDR3 DIMM Slots

3.2.5 Digital I/O Connector

3.2.6 DVI-D Connector (DVI Model Only)

3.2.7 Fan Connector (CPU)

3.2.8 Floppy Disk Drive Connector

3.2.9 Front Panel Connector

3.2.10 I2C Connector

3.2.11 Infrared Interface Connector

3.2.12 Keyboard/Mouse Connector

3.2.13 Parallel Port Connector

3.2.14 SATA 3Gb/s Drive Connectors

3.2.15 Serial Port Connectors, RS-232

3.2.16 Serial Port Connector, RS-422/485

3.2.17 SMBus Connector

3.2.18 SPI ROM Connector

3.2.19 TPM Connector

3.2.20 USB Connectors

3.3 External Peripheral Interface Connector Panel

3.3.1 Ethernet Connectors

3.3.2 USB Connectors

3.3.3 VGA Connector

4 Installation

4.1 Anti-static Precautions

4.2 Installation Considerations

4.2.1 Socket LGA1155 CPU Installation

4.2.2 Socket LGA1155 Cooling Kit Installation

4.2.3 DIMM Installation

4.3 Jumper Settings

4.3.1 AT/ATX Power Select Jumper

4.3.2 Clear CMOS Jumper

4.3.3 Wake-on LAN Jumper

4.4 Chassis Installation

4.4.1 Airflow

4.4.2 CPU Card Installation

4.5 Internal Peripheral Device Connections

4.5.1 Dual RS-232 Cable with Slot Bracket

4.5.2 DVI-D/USB Kit Installation (DVI Model Only)

4.5.3 SATA Drive Connection

4.5.4 USB Cable (Dual Port) with Slot Bracket

4.6 External Peripheral Interface Connection

4.6.1 LAN Connection

4.6.2 USB Device Connection (Single Connector)

4.6.3 VGA Monitor Connection

5 BIOS

5.1 Introduction

5.1.1 Starting Setup

5.1.2 Using Setup

5.1.3 Getting Help

5.1.4 Unable to Reboot after Configuration Changes

5.1.5 BIOS Menu Bar

5.2 Main

5.3 Advanced

5.3.1 ACPI Settings

5.3.2 Trusted Computing