Page 1
NANO-QM770 EPIC SBC
MODEL:
NANO-QM770
EPIC SBC with 3rd Generation 22nm Intel® Mobile CPU
Up to 8.0 GB DDR3, DVI, HDMI, LVDS, Dual GbE,
SATA 6Gb/s, USB 3.0, PCIe Mini, Intel® AMT, RoHS
User Manual
Rev. 1.02 – 23 April, 2014
Page i
Page 2
NANO-QM770 EPIC SBC
Revision
Date Version Changes
23 April, 2014 1.02 Modified Table 3-24: LAN Pinouts
9 December, 2013 1.01 Updated Appendix D.2: DIO Connector Pinouts
24 May, 2012 1.00 Initial release
Page ii
Page 3
NANO-QM770 EPIC SBC
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
Copyright
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page iii
Page 4
NANO-QM770 EPIC SBC
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 INTRODUCTION........................................................................................................... 2
1.2 BENEFITS ................................................................................................................... 2
1.3 FEATURES................................................................................................................... 2
1.4 CONNECTORS ............................................................................................................. 3
1.5 DIMENSIONS............................................................................................................... 5
1.6 DATA FLOW................................................................................................................ 6
1.7 TECHNICAL SPECIFICATIONS ...................................................................................... 7
2 PACKING LIST............................................................................................................. 9
2.1 ANTI-STATIC PRECAUTIONS...................................................................................... 10
2.2 UNPACKING PRECAUTIONS....................................................................................... 10
2.3 PACKING LIST............................................................................................................11
2.4 OPTIONAL ITEMS...................................................................................................... 12
3 CONNECTOR PINOUTS........................................................................................... 14
3.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 15
3.1.1 Layout .............................................................................................................. 15
3.1.2 Peripheral Interface Connectors ..................................................................... 16
3.1.3 External Interface Panel Connectors............................................................... 17
3.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 18
3.2.1 Audio Connector .............................................................................................. 18
3.2.2 Battery Connector............................................................................................ 19
3.2.3 Digital I/O Connector...................................................................................... 20
3.2.4 Fan Connector (CPU)...................................................................................... 20
3.2.5 Fan Connector (System) .................................................................................. 21
3.2.6 Front Panel Connector.................................................................................... 22
3.2.7 Keyboard/Mouse Connector............................................................................ 23
3.2.8 LVDS Connector.............................................................................................. 23
3.2.9 LVDS Backlight Connector.............................................................................. 25
3.2.10 PCIe Mini Card Slot ...................................................................................... 25
Page iv
Page 5
NANO-QM770 EPIC SBC
3.2.11 Power Connector (12V) ................................................................................. 27
3.2.12 RS-232 Serial Port Connectors (COM1, COM2).......................................... 28
3.2.13 RS-422/485 Serial Port Connector (COM3).................................................. 28
3.2.14 SATA Drive Connectors ................................................................................. 29
3.2.15 SATA Power Connectors................................................................................ 30
3.2.16 SMBus Connector .......................................................................................... 31
3.2.17 SO-DIMM Connector..................................................................................... 32
3.2.18 SPI Flash Connector...................................................................................... 32
3.2.19 TPM Connector.............................................................................................. 33
3.2.20 USB 2.0 Connector ........................................................................................ 34
3.3 EXTERNAL INTERFACE CONNECTORS ....................................................................... 35
3.3.1 DVI Connector................................................................................................. 35
3.3.2 Ethernet Connectors ........................................................................................ 36
3.3.3 HDMI Connectors............................................................................................ 37
3.3.4 USB 3.0 Connectors......................................................................................... 38
4 INSTALLATION ......................................................................................................... 40
4.1 ANTI-STATIC PRECAUTIONS...................................................................................... 41
4.2 INSTALLATION CONSIDERATIONS.............................................................................. 41
4.3 SO-DIMM INSTALLATION ....................................................................................... 43
4.4 PCIE MINI CARD INSTALLATION .............................................................................. 43
4.5 JUMPER SETTINGS .................................................................................................... 44
4.5.1 AT/ATX Mode Selection................................................................................... 45
4.5.2 Clear CMOS..................................................................................................... 46
4.5.3 Clear ME RTC Registers ................................................................................. 47
4.5.4 Flash Descriptor Security Override................................................................. 48
4.5.5 LVDS Voltage Selection.................................................................................... 49
4.5.6 LVDS Resolution Selection.............................................................................. 49
4.5.7 PCIe Mini/mSATA Mode Selection .................................................................. 50
4.6 CHASSIS INSTALLATION............................................................................................ 51
4.6.1 Airflow.............................................................................................................. 51
4.6.2 Motherboard Installation................................................................................. 51
4.7 INTERNAL PERIPHERAL DEVICE CONNECTIONS........................................................ 52
4.7.1 AT Power Connection ...................................................................................... 52
4.7.2 Audio Kit Installation....................................................................................... 53
Page v
Page 6
NANO-QM770 EPIC SBC
4.7.3 SATA Drive Connection ................................................................................... 54
4.7.4 Single RS-232 Cable (w/o Bracket) ................................................................. 55
4.8 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 56
4.8.1 DVI Display Device Connection...................................................................... 56
4.8.2 HDMI Display Device Connection.................................................................. 57
4.8.3 LAN Connection............................................................................................... 58
4.8.4 USB Connection............................................................................................... 59
4.9 INTEL
®
AMT SETUP PROCEDURE............................................................................. 60
5 BIOS.............................................................................................................................. 62
5.1 INTRODUCTION......................................................................................................... 63
5.1.1 Starting Setup................................................................................................... 63
5.1.2 Using Setup...................................................................................................... 63
5.1.3 Getting Help..................................................................................................... 64
5.1.4 Unable to Reboot After Configuration Changes.............................................. 64
5.1.5 BIOS Menu Bar................................................................................................ 64
5.2 MAIN........................................................................................................................ 65
5.3 ADVANCED............................................................................................................... 66
5.3.1 ACPI Configuration......................................................................................... 67
5.3.2 RTC Wake Settings........................................................................................... 68
5.3.3 T rusted Computing........................................................................................... 69
5.3.4 CPU Configuration.......................................................................................... 70
5.3.5 SATA Configuration ......................................................................................... 72
5.3.6 Intel(R) Rapid Start Technology....................................................................... 73
5.3.7 Intel TXT(LT) Configuration............................................................................ 73
5.3.8 AMT Configuration.......................................................................................... 74
5.3.9 USB Configuration........................................................................................... 75
5.3.10 F81866 Super IO Configuration.................................................................... 76
5.3.10.1 Serial Port n Configuration..................................................................... 77
5.3.11 F81866 H/W Monitor..................................................................................... 80
5.3.11.1 Smart Fan Mode Configuration.............................................................. 81
5.3.12 Serial Port Console Redirection.................................................................... 82
5.3.13 IEI Feature..................................................................................................... 83
5.4 CHIPSET ................................................................................................................... 84
5.4.1 PCH-IO Configuration .................................................................................... 85
Page vi
Page 7
NANO-QM770 EPIC SBC
5.4.2 System Agent (SA) Configuration .................................................................... 86
5.4.2.1 Graphics Configuration............................................................................. 87
5.4.2.2 Memory Configuration ............................................................................. 90
5.5 BOOT........................................................................................................................ 91
5.6 SECURITY................................................................................................................. 94
5.7 EXIT......................................................................................................................... 94
6 SOFTWARE DRIVERS.............................................................................................. 96
6.1 AVAILABLE SOFTWARE DRIVERS .............................................................................. 97
6.2 SOFTWARE INSTALLATION ........................................................................................ 97
6.3 CHIPSET DRIVER INSTALLATION............................................................................... 99
6.4 GRAPHICS DRIVER INSTALLATION.......................................................................... 102
6.5 LAN DRIVER INSTALLATION.................................................................................. 105
6.6 AUDIO DRIVER INSTALLATION ............................................................................... 108
6.7 INTEL® RAPID STORAGE TECHNOLOGY DRIVER INSTALLATION.............................111
6.8 USB 3.0 DRIVER INSTALLATION .............................................................................114
6.9 INTEL® AMT DRIVER INSTALLATION .....................................................................117
A BIOS OPTIONS ........................................................................................................ 120
B ONE KEY RECOVERY........................................................................................... 123
B.1 ONE KEY RECOVERY INTRODUCTION .................................................................... 124
B.1.1 System Requirement....................................................................................... 125
B.1.2 Supported Operating System......................................................................... 126
B.2 SETUP PROCEDURE FOR WINDOWS........................................................................ 127
B.2.1 Hardware and BIOS Setup ............................................................................ 128
B.2.2 Create Partitions........................................................................................... 128
B.2.3 Install Operating System, Drivers and Applications..................................... 132
B.2.4 Building the Recovery Partition.................................................................... 133
B.2.5 Create Factory Default Image....................................................................... 135
B.3 AUTO RECOVERY SETUP PROCEDURE.................................................................... 140
B.4 SETUP PROCEDURE FOR LINUX.............................................................................. 145
B.5 RECOVERY TOOL FUNCTIONS................................................................................ 148
B.5.1 Factory Restore............................................................................................. 150
B.5.2 Backup System............................................................................................... 151
B.5.3 Restore Your Last Backup.............................................................................. 152
Page vii
Page 8
B.5.4 Manual........................................................................................................... 153
B.6 RESTORE SYSTEMS FROM A LINUX SERVER THROUGH LAN.................................. 154
B.6.1 Configure DHCP Server Settings.................................................................. 155
B.6.2 Configure TFTP Settings ............................................................................... 156
B.6.3 Configure One Key Recovery Server Settings............................................... 157
B.6.4 Start the DHCP, TFTP and HTTP................................................................. 158
B.6.5 Create Shared Directory................................................................................ 158
B.6.6 Setup a Client System for Auto Recovery...................................................... 159
B.7 OTHER INFORMATION ............................................................................................ 162
B.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller....................... 162
B.7.2 System Memory Requirement ........................................................................ 164
C TERMINOLOGY ..................................................................................................... 165
D DIGITAL I/O INTERFACE..................................................................................... 169
NANO-QM770 EPIC SBC
D.1 INTRODUCTION...................................................................................................... 170
D.2 DIO CONNECTOR PINOUTS ................................................................................... 170
D.3 ASSEMBLY LANGUAGE SAMPLES........................................................................... 170
D.3.1 Enable the DIO Input Function .................................................................... 170
D.3.2 Enable the DIO Output Function.................................................................. 171
E HAZARDOUS MATERIALS DISCLOSURE ....................................................... 172
E.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 173
Page viii
Page 9
NANO-QM770 EPIC SBC
List of Figures
Figure 1-1: NANO-QM770...............................................................................................................2
Figure 1-2: Connectors (Front)......................................................................................................3
Figure 1-3: Connectors (Solder Side)...........................................................................................4
Figure 1-4: Dimensions (mm)........................................................................................................5
Figure 1-5: Data Flow Diagram......................................................................................................6
Figure 3-1: Connector and Jumper Locations...........................................................................15
Figure 3-2: Connector and Jumper Locations (Solder Side) ...................................................16
Figure 3-3: Audio Connector Location.......................................................................................18
Figure 3-4: Battery Connector Location.....................................................................................19
Figure 3-5: Digital I/O Connector Location ................................................................................20
Figure 3-6: CPU Fan Connector Location..................................................................................21
Figure 3-7: System Fan Connector Location.............................................................................21
Figure 3-8: Front Panel Connector Location .............................................................................22
Figure 3-9: Keyboard/Mouse Connector Location....................................................................23
Figure 3-10: LVDS Connector Location......................................................................................24
Figure 3-11: LVDS Backlight Inverter Connector......................................................................25
Figure 3-12: PCIe Mini Card Slot Location.................................................................................26
Figure 3-13: Power Connector Location ....................................................................................27
Figure 3-14: RS-232 Serial Port Connector Locations..............................................................28
Figure 3-15: RS-422/485 Serial Port Connector Location.........................................................29
Figure 3-16: SATA Drive Connector Locations.........................................................................30
Figure 3-17: SATA Power Connector Locations .......................................................................31
Figure 3-18: SMBus Connector Location...................................................................................31
Figure 3-19: SO-DIMM Connector Location...............................................................................32
Figure 3-20: SPI Flash Connector Location...............................................................................33
Figure 3-21: TPM Connector Location........................................................................................34
Figure 3-22: USB Connector Location........................................................................................35
Figure 3-23: External Interface Connectors...............................................................................35
Figure 3-24: DVI-I Connector.......................................................................................................36
Figure 3-25: Ethernet Connector.................................................................................................37
Page ix
Page 10
Figure 3-26: HDMI Connector......................................................................................................38
Figure 4-1: SO-DIMM Installation................................................................................................43
Figure 4-2: PCIe Mini Card Installation.......................................................................................44
Figure 4-3: AT/ATX Mode Selection Jumper Location..............................................................46
Figure 4-4: Clear CMOS Jumper Location .................................................................................47
Figure 4-5: Clear ME RTC Registers Jumper Location.............................................................48
Figure 4-6: Flash Descriptor Security Override Jumper Location ..........................................48
Figure 4-7: LVDS Voltage Selection Jumper Location .............................................................49
Figure 4-8: LVDS Resolution Selection Jumper Location........................................................50
Figure 4-9: PCIe Mini/mSATA Mode Selection Jumper Location............................................51
Figure 4-10: Power Cable to Motherboard Connection............................................................52
Figure 4-11: Connect Power Cable to Power Supply................................................................53
Figure 4-12: Audio Kit Cable Connection ..................................................................................54
Figure 4-13: SATA Drive Cable Connection...............................................................................55
NANO-QM770 EPIC SBC
Figure 4-14: Single RS-232 Cable Installation ...........................................................................56
Figure 4-15: DVI Connector.........................................................................................................57
Figure 4-16: HDMI Connection....................................................................................................58
Figure 4-17: LAN Connection......................................................................................................59
Figure 4-18: USB Connector........................................................................................................60
Figure 6-1: Introduction Screen..................................................................................................98
Figure 6-2: Available Drivers.......................................................................................................98
Figure 6-3: Chipset Driver Welcome Screen..............................................................................99
Figure 6-4: Chipset Driver License Agreement...................................................................... 100
Figure 6-5: Chipset Driver Read Me File ................................................................................. 100
Figure 6-6: Chipset Driver Setup Operations ......................................................................... 101
Figure 6-7: Chipset Driver Installation Finish Screen............................................................ 102
Figure 6-8: Graphics Driver Welcome Screen........................................................................ 103
Figure 6-9: Graphics Driver License Agreement.................................................................... 103
Figure 6-10: Graphics Driver Setup Operations..................................................................... 104
Figure 6-11: Graphics Driver Installation Finish Screen ....................................................... 104
Figure 6-12: Windows Control Panel....................................................................................... 105
Figure 6-13: System Control Panel.......................................................................................... 105
Figure 6-14: Device Manager List ............................................................................................ 106
Figure 6-15: Update Driver Software Window ........................................................................ 107
Figure 6-16: Locate Driver Files............................................................................................... 107
Page x
Page 11
NANO-QM770 EPIC SBC
Figure 6-17: LAN Driver Installation ........................................................................................ 108
Figure 6-18: LAN Driver Installation Complete....................................................................... 108
Figure 6-19: InstallShield Wizard Welcome Screen............................................................... 109
Figure 6-20: Audio Driver Software Configuration................................................................. 110
Figure 6-21: Restart the Computer .......................................................................................... 110
Figure 6-22: SATA RAID Driver Welcome Screen.................................................................. 111
Figure 6-23: SATA RAID Driver License Agreement.............................................................. 112
Figure 6-24: SATA RAID Driver Read Me File......................................................................... 112
Figure 6-25: SATA RAID Driver Setup Operations................................................................. 113
Figure 6-26: SATA RAID Driver Installation Finish Screen ................................................... 113
Figure 6-27: USB 3.0 Driver Welcome Screen........................................................................ 114
Figure 6-28: USB 3.0 Driver License Agreement.................................................................... 115
Figure 6-29: USB 3.0 Driver Read Me File............................................................................... 115
Figure 6-30: USB 3.0 Driver Setup Operations....................................................................... 116
Figure 6-31: USB 3.0 Driver Installation Finish Screen ......................................................... 116
Figure 6-32: Intel® ME Driver Welcome Screen ..................................................................... 118
Figure 6-33: Intel® ME Driver License Agreement................................................................. 118
Figure 6-34: Intel® ME Driver Setup Operations.................................................................... 119
Figure 6-35: Intel® ME Driver Installation Finish Screen ...................................................... 119
Figure B-1: IEI One Key Recovery Tool Menu........................................................................ 124
Figure B-2: Launching the Recovery Tool.............................................................................. 129
Figure B-3: Recovery Tool Setup Menu .................................................................................. 129
Figure B-4: Command Prompt ................................................................................................. 130
Figure B-5: Partition Creation Commands.............................................................................. 131
Figure B-6: Launching the Recovery Tool.............................................................................. 133
Figure B-7: Manual Recovery Environment for Windows..................................................... 133
Figure B-8: Building the Recovery Partition........................................................................... 134
Figure B-9: Press Any Key to Continue.................................................................................. 134
Figure B-10: Press F3 to Boot into Recovery Mode............................................................... 135
Figure B-11: Recovery Tool Menu ........................................................................................... 135
Figure B-12: About Symantec Ghost Window........................................................................ 136
Figure B-13: Symantec Ghost Path ......................................................................................... 136
Figure B-14: Select a Local Source Drive ............................................................................... 137
Figure B-15: Select a Source Partition from Basic Drive ...................................................... 137
Figure B-16: File Name to Copy Image to ............................................................................... 138
Page xi
Page 12
Figure B-17: Compress Image.................................................................................................. 138
Figure B-18: Image Creation Confirmation............................................................................. 139
Figure B-19: Creating Image..................................................................................................... 139
Figure B-20: Image Creation Complete................................................................................... 139
Figure B-21: Press Any Key to Continue................................................................................ 140
Figure B-22: Auto Recovery Utility.......................................................................................... 141
Figure B-23: Disable Automatically Restart............................................................................ 141
Figure B-24: Launching the Recovery Tool............................................................................ 142
Figure B-25: Auto Recovery Environment for Windows ....................................................... 142
Figure B-26: Building the Auto Recovery Partition................................................................ 143
Figure B-27: Factory Default Image Confirmation ................................................................. 143
Figure B-28: Creating Image..................................................................................................... 144
Figure B-29: Press Any Key to Continue................................................................................ 144
Figure B-30: IEI Feature BIOS Menu........................................................................................ 145
NANO-QM770 EPIC SBC
Figure B-31: Partitions for Linux.............................................................................................. 146
Figure B-32: Manual Recovery Environment for Linux ......................................................... 147
Figure B-33: Access menu.lst in Linux (Text Mode).............................................................. 147
Figure B-34: Recovery Tool Menu ........................................................................................... 148
Figure B-35: Recovery Tool Main Menu.................................................................................. 149
Figure B-36: Restore Factory Default...................................................................................... 150
Figure B-37: Recovery Complete Window.............................................................................. 150
Figure B-38: Backup System.................................................................................................... 151
Figure B-39: System Backup Complete Window ................................................................... 151
Figure B-40: Restore Backup................................................................................................... 152
Figure B-41: Restore System Backup Complete Window..................................................... 152
Figure B-42: Symantec Ghost Window ................................................................................... 153
Figure B-43: Disable Automatically Restart............................................................................ 160
Page xii
Page 13
NANO-QM770 EPIC SBC
List of Tables
Table 1-1: Technical Specifications..............................................................................................8
Table 2-1: Packing List.................................................................................................................12
Table 2-2: Optional Items.............................................................................................................13
Table 3-1: Peripheral Interface Connectors...............................................................................17
Table 3-2: Rear Panel Connectors..............................................................................................17
Table 3-3: Audio Connector Pinouts ..........................................................................................18
Table 3-4: Battery Connector Pinouts........................................................................................19
Table 3-5: Digital I/O Connector Pinouts....................................................................................20
Table 3-6: CPU Fan Connector Pinouts......................................................................................21
Table 3-7: System Fan Connector Pinouts................................................................................22
Table 3-8: Front Panel Connector Pinouts.................................................................................22
Table 3-9: Keyboard/Mouse Connector Pinouts .......................................................................23
Table 3-10: LVDS Connector Pinouts.........................................................................................24
Table 3-11: Backlight Inverter Connector Pinouts....................................................................25
Table 3-12: PCIe Mini Card Slot Pinouts ....................................................................................27
Table 3-13: Power Connector Pinouts........................................................................................27
Table 3-14: Serial Port Connector Pinouts ................................................................................28
Table 3-15: RS-422/485 Serial Port Connector Pinouts............................................................29
Table 3-16: D-sub 9 RS-422/485 Pinouts....................................................................................29
Table 3-17: SATA Drive Connector Pinouts...............................................................................30
Table 3-18: SATA Power Connector Pinouts.............................................................................31
Table 3-19: SMBus Connector Pinouts ......................................................................................32
Table 3-20: SPI Flash Connector Pinouts ..................................................................................33
Table 3-21: TPM Connector Pinouts...........................................................................................34
Table 3-22: USB Port Connector Pinouts...................................................................................35
Table 3-23: DVI Connector Pinouts.............................................................................................36
Table 3-24: LAN Pinouts ..............................................................................................................37
Table 3-25: Connector LEDs........................................................................................................37
Table 3-26: HDMI Connector Pinouts .........................................................................................38
Table 3-27: USB Port Pinouts......................................................................................................39
Page xiii
Page 14
Table 4-1: Jumpers.......................................................................................................................45
Table 4-2: AT/ATX Mode Selection Jumper Settings................................................................45
Table 4-3: Clear CMOS Jumper Settings....................................................................................47
Table 4-4: Clear ME RTC Registers Jumper Settings...............................................................47
Table 4-5: Flash Descriptor Security Override Jumper Settings.............................................48
Table 4-6: LVDS Voltage Selection Jumper Settings................................................................49
Table 4-7: LVDS Screen Resolution Jumper Settings..............................................................50
Table 4-8: PCIe Mini/mSATA Mode Selection Jumper Settings...............................................51
Table 5-1: BIOS Navigation Keys................................................................................................64
Table 6-1: Digital I/O Connector Pinouts................................................................................. 170
NANO-QM770 EPIC SBC
Page xiv
Page 15
NANO-QM770 EPIC SBC
BIOS Menus
BIOS Menu 1: Main.......................................................................................................................65
BIOS Menu 2: Advanced..............................................................................................................66
BIOS Menu 3: ACPI Configuration..............................................................................................67
BIOS Menu 4: RTC Wake Settings..............................................................................................68
BIOS Menu 5: Trusted Computing..............................................................................................69
BIOS Menu 6: CPU Configuration...............................................................................................70
BIOS Menu 7: SATA Configuration.............................................................................................72
BIOS Menu 8: Intel(R) Rapid Start Technology .........................................................................73
BIOS Menu 9: Intel TXT(LT) Configuration ................................................................................74
BIOS Menu 10: AMT Configuration.............................................................................................74
BIOS Menu 11: USB Configuration.............................................................................................75
BIOS Menu 12: Super IO Configuration......................................................................................76
BIOS Menu 13: Serial Port n Configuration Menu.....................................................................77
BIOS Menu 14: Hardware Health Configuration........................................................................80
BIOS Menu 15: FAN 1 Configuration..........................................................................................81
BIOS Menu 16: Serial Port Console Redirection.......................................................................82
BIOS Menu 17: IEI Feature...........................................................................................................83
BIOS Menu 18: Chipset................................................................................................................84
BIOS Menu 19:PCH-IO Configuration.........................................................................................85
BIOS Menu 20: System Agent (SA) Configuration....................................................................87
BIOS Menu 21: Graphics Configuration.....................................................................................88
BIOS Menu 22: Memory Configuration.......................................................................................91
BIOS Menu 23: Boot.....................................................................................................................91
BIOS Menu 24: Security...............................................................................................................94
BIOS Menu 25:Exit........................................................................................................................95
Page xv
Page 16
Page 17
NANO-QM770 EPIC SBC
Chapter
1
1 Introduction
Page 1
Page 18
1.1 Introduction
Figure 1-1: NANO-QM770
The NANO-QM770 is an EPIC SBC with a 3
NANO-QM770 EPIC SBC
rd
generation 22nm Intel® mobile CPU and
Intel® QM77 Express Chipset. Storage on the board is handled by the SATA 6Gb/s ports
for connecting a hard drive, optical drive or SSD. The PCIe Mini slot allows an mSATA
card to be installed.
The board has three types of graphics outputs. A DVI-I output connects to a DVI monitor
or a traditional VGA monitor. One LVDS connector supports 24-bit dual-channel display
and two HDMI connectors support HDMI 1080p display.
Other slots and connectors include RS-232, RS-422/485, gigabit Ethernet, USB 3.0 ports,
USB 2.0 ports and digital I/O.
1.2 Benefits
Some of the NANO-QM770 motherboard benefits include:
Low power consumption
Wide range of I/O interfaces
Triple independent display support
1.3 Features
Some of the NANO-QM770 motherboard features are listed below:
Page 2
Page 19
NANO-QM770 EPIC SBC
EPIC form factor
RoHS compliant
Intel® AMT 8.0 support
Dual GbE
Supports HDMI, LVDS and DVI-I interface for triple independent display
(HDMI V1.3a compliant)
Six USB ports (two USB 2.0, four USB 3.0)
Three serial ports
PCIe Mini card slot
1.4 Connectors
The connectors on the NANO-QM770 are shown in the figure below.
Figure 1-2: Connectors (Front)
Page 3
Page 20
NANO-QM770 EPIC SBC
Figure 1-3: Connectors (Solder Side)
Page 4
Page 21
NANO-QM770 EPIC SBC
1.5 Dimensions
The main dimensions of the NANO-QM770 are shown in the diagram below.
Figure 1-4: Dimensions (mm)
Page 5
Page 22
1.6 Data Flow
Figure 1-5 shows the data flow between the system chipset, the CPU and other
components installed on the motherboard.
NANO-QM770 EPIC SBC
Page 6
Figure 1-5: Data Flow Diagram
Page 23
NANO-QM770 EPIC SBC
1.7 Technical Specifications
NANO-QM770 technical specifications are listed in Table 1-1.
Specification NANO-QM770
Form Factor
CPU Socket
CPU
System Chipset
Memory
Graphics Engine
BIOS
Digital I/O
Ethernet Controllers
Audio
Super I/O Controller
Watchdog Timer
EPIC
Socket G2
rd
3
generation 22nm Intel® mobile CPU
Intel® QM77
One 204-pin 1600/1333/1066 MHz DDR3 SO-DIMM supported
(system max. 8GB)
Intel® Gen 7 with DirectX 11, OGL 3.1, OCL 1.1
UEFI BIOS
8-bit, 4-bit input/4-bit output
Intel® 82579 PHY with Intel® AMT 8.0 support (LAN1)
Intel® 82583V PCIe Ethernet controller
Realtek ALC662 HD Audio codec
Fintek F81866
Software programmable supports 1–255 sec. system reset
Expansion
I/O Interface Connectors
Display Output Ports
(Triple Display
Supported)
Fan connector
Keyboard/Mouse
Serial Ports
1 x Full-size PCIe Mini slot supports mSATA SSD
1 x DVI-I with analog CRT and DVI support
2 x HDMI (1080p)
Dual-channel 24-bit LVDS, resolution up to 1600x1200
One 4-pin wafer for CPU fan
One 3-pin wafer for system fan
One internal 6-pin wafer connector
Two RS-232 COM connectors (10-pin header)
One RS-422/485 COM connector (4-pin wafer)
Page 7
Page 24
NANO-QM770 EPIC SBC
USB Ports
SMBus
Storage
SATA
Environmental and Power Specifications
Power Supply
Power Connector
Power Consumption
Operating Temperature
Storage Temperature
Operating Humidity
Physical Specifications
Two USB 2.0 (via pin head er)
Four external USB 3.0 ports
One 4-pin wafer connector
Two independent SATA channels with 6Gb/s data transfer rates
12 V only, AT/ATX support
1 x Internal 4-pin (2x2) power connector
12 V @ 5.87 A (2.30 GHz Intel® Core™ i7-3610QE CPU with 4 GB
1333 MHz DDR3 memory)
-10ºC–60ºC
-20ºC–70ºC
5%–95% (non-condensing)
Dimensions
Weight GW/NW
Table 1-1: Technical Specifications
115 mm x 165 mm
850 g/350 g
Page 8
Page 25
NANO-QM770 EPIC SBC
Chapter
2
2 Packing List
Page 9
Page 26
2.1 Anti-static Precautions
WARNING!
Static electricity can destroy certain electronics. Make sure to follow the
ESD precautions to prevent damage to the product, and injury to the
user.
Make sure to adhere to the following guidelines:
Wear an anti-static wristband: - Wearing an anti-static wristband can
prevent electrostatic discharge.
Self-grounding:- Touch a grounded conductor every few minutes to
discharge any excess static buildup.
NANO-QM770 EPIC SBC
Use an anti-static pad: When configuring any circuit board, place it on an
anti-static mat.
Only handle the edges of the PCB:- Don't touch the surface of the
motherboard. Hold the motherboard by the edges when handling.
2.2 Unpacking Precautions
When the NANO-QM770 is unpacked, please do the following:
Follow the antistatic guidelines above.
Make sure the packing box is facing upwards whe n opening.
Make sure all the packing list items are present.
Page 10
Page 27
NANO-QM770 EPIC SBC
2.3 Packing List
NOTE:
If any of the components listed in the checklist below are missing, do
not proceed with the installation. Contact the IEI reseller or vendor the
NANO-QM770 was purchased from or contact an IEI sales
representative directly by sending an email to
The NANO-QM770 is shipped with the following compone nts:
Quantity Item and Part Number Image
1 NANO-QM770 SBC
2 SATA and power cable
(P/N: 32801-000201-300-RS)
2 RS-232 cable
(P/N: 32200-000049-RS)
sales@ieiworld.com.tw.
1 Audio cable
(P/N: 32007-002600-100-RS)
1 AT 12V Cable
(P/N: 32100-087100-RS)
1 Mini jumper pack (2.0mm)
(P/N: 33101-000657-RS)
Page 11
Page 28
Quantity Item and Part Number Image
1 Utility CD
1 One Key Recovery CD
1 Quick installation guide
Table 2-1: Packing List
NANO-QM770 EPIC SBC
2.4 Optional Items
These optional items are available.
Item and Part Number Image
RS-422/485 cable
(P/N: 32205-003800-300-RS)
Dual USB port cable
(P/N: 32000-070301-RS)
KB/MS PS/2 Y-cable
(P/N: 32000-023800-RS)
CPU cooler
(P/N: CF-989A-RS-R12)
Page 12
Page 29
NANO-QM770 EPIC SBC
Item and Part Number Image
Infineon TPM module
(P/N: TPM-IN01-R1 1)
Table 2-2: Optional Items
Page 13
Page 30
NANO-QM770 EPIC SBC
Chapter
3
3 Connector Pinouts
Page 14
Page 31
NANO-QM770 EPIC SBC
3.1 Peripheral Interface Connectors
Section 3.1.1 shows peripheral interface connector locations. Section 3.1.2 lists all the
peripheral interface connectors seen in Section
3.1.1.
3.1.1 Layout
The figure below shows the on-board peripheral connectors, rear panel peripheral
connectors and on-board jumpers.
Figure 3-1: Connector and Jumper Locations
Page 15
Page 32
NANO-QM770 EPIC SBC
Figure 3-2: Connector and Jumper Locations (Solder Side)
3.1.2 Peripheral Interface Connectors
The table below shows a list of the peripheral interface connectors on the NANO-QM770.
Detailed descriptions of these connectors can be found below.
Connector Type Label
Audio connector 10-pin header AUDIO1
Battery connector 2-pin wafer BAT1
Digital I/O connector 10-pin header DIO1
Fan connector (CPU) 4-pin wafer CPU_FAN1
Fan connector (system) 3-pin wafer SYS_FAN1
Front panel connector 10-pin header F_PANEL1
Page 16
Keyboard/mouse connector 6-pin wafer KB_MS1
LVDS connector 30-pin crimp LVDS1
LVDS backlight connector 5-pin wafer INVERTER1
Page 33
NANO-QM770 EPIC SBC
Connector Type Label
PCIe Mini card slot PCIe Mini card slot CN4
Power connector (12V) 4-pin connector PWR1
RS-232 serial ports (COM1, COM2) 10-pin header COM1, COM2
RS-422/485 serial port (COM3) 4-pin wafer COM3
SATA connectors SATA connector S_ATA1, S_ATA2
SA TA power connectors 2-pin wafer CN1, CN2
SMBus connector 4-pin wafer CN3
SO-DIMM connector SO-DIMM connector DIMM1
SPI Flash 6-pin wafer JSPI1
TPM connector 20-pin header TPM1
USB 2.0 connector 8-pin header USB1
Table 3-1: Peripheral Interface Connectors
3.1.3 External Interface Panel Connectors
The table below lists the rear panel connectors on the NANO-QM770. Detailed
descriptions of these connectors can be found in a later section.
Connector Type Label
DVI-I connector DVI-I CON1
Ethernet connectors RJ-45 LAN1, LAN2
HDMI connectors HDMI HDMI1, HDMI2
USB 3.0 connectors USB 3.0 USB_CON1
USB_CON2
Table 3-2: Rear Panel Connectors
Page 17
Page 34
3.2 Internal Peripheral Connectors
Internal peripheral connectors are found on the motherboard and are only accessible
when the motherboard is outside of the chassis. T his se ction h as complet e d esc ription s of
all the internal, peripheral connectors on the NANO-QM770.
3.2.1 Audio Connector
CN Label: AUDIO1
NANO-QM770 EPIC SBC
CN Type:
CN Location:
CN Pinouts:
This connector connects to speaker, microphone and audio input connectors on the front
panel.
Figure 3-3: Audio Connector Location
10-pin header
Figure 3-3
See
Table 3-3
See
Pin Description Pin Description
Page 18
1 LFRONT-R 2 LLINE-R
3 GND 4 GND
5 LFRONT-L 6 LLINE-L
7 GND 8 GND
9 LMIC1-CONN-R 10 LMIC1-CONN-L
Table 3-3: Audio Connector Pinouts
Page 35
NANO-QM770 EPIC SBC
3.2.2 Battery Connector
CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Only
certified engineers should replace the on-board battery.
Dispose of used batteries according to instructions and local
regulations.
CN Label: BAT1
CN Type:
CN Location:
CN Pinouts:
This is connected to the system battery. The battery provides power to the system clock to
retain the time when power is turned off.
Figure 3-4: Battery Connector Location
2-pin wafer
Figure 3-4
See
Table 3-4
See
Pin Description
1 Battery+
2 Ground
Table 3-4: Battery Connector Pinouts
Page 19
Page 36
3.2.3 Digital I/O Connector
CN Label: DIO1
NANO-QM770 EPIC SBC
CN Type:
CN Location:
CN Pinouts:
The digital I/O connector provides programmable input and output for external devices.
The digital I/O provides 4-bit output and 4-bit input.
Figure 3-5: Digital I/O Connector Location
10-pin header
Figure 3-5
See
Table 3-5
See
Pin Description Pin Description
1 GND 2 +V5S
3 Output 3 4 Output 2
5 Output 1 6 Output 0
7 Input 3 8 Input 2
9 Input 1 10 Input 0
Table 3-5: Digital I/O Connector Pinouts
3.2.4 Fan Connector (CPU)
CN Label: CPU_FAN1
CN Type:
CN Location:
CN Pinouts:
4-pin wafer
Figure 3-6
See
Table 3-6
See
Page 20
Page 37
NANO-QM770 EPIC SBC
The fan connector attaches to a CPU cooling fan.
Figure 3-6: CPU Fan Connector Location
Pin Description
1
2
3
4
Table 3-6: CPU Fan Connector Pinouts
GND
+V12S
Rotation Signal
PWM Control Signal
3.2.5 Fan Connector (System)
CN Label: SYS_FAN1
CN Type:
CN Location:
CN Pinouts:
The fan connector attaches to a system cooling fan.
3-pin wafer
Figure 3-7
See
Table 3-7
See
Figure 3-7: System Fan Connector Location
Page 21
Page 38
NANO-QM770 EPIC SBC
Pin Description
1
2
3
Rotation Signal
+12V
GND
Table 3-7: System Fan Connector Pinouts
3.2.6 Front Panel Connector
CN Label: F_PANEL1
CN Type:
CN Location:
CN Pinouts:
The front panel connector connects to the indicator LEDs and buttons on the computer's
front panel.
10-pin header
Figure 3-8
See
Table 3-8
See
Figure 3-8: Front Panel Connector Location
Pin Description Pin Description
1 NC 6 LED_PWR
2 GROUND 7 LED_PWR Power
Button
LED
3 PWR_BTN4 IDE_LED_PWR
5 SATA_LED#
Table 3-8: Front Panel Connector Pinouts
Page 22
Power
LED
8 GROUND
9 EXTRST- HDD
Reset
10 Ground
Page 39
NANO-QM770 EPIC SBC
3.2.7 Keyboard/Mouse Connector
CN Label: KB_MS1
CN Type:
CN Location:
CN Pinouts:
6-pin wafer
Figure 3-9
See
Table 3-9
See
The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a
PS/2 keyboard and mouse.
Figure 3-9: Keyboard/Mouse Connector Location
Pin Description
1 VCC5_KBMS
2 Mouse Data
3 Mouse Clock
4 Keyboard Data
5 Keyboard Clock
6 GND
Table 3-9: Keyboard/Mouse Connector Pinouts
3.2.8 LVDS Connector
CN Label: LVDS1
CN Type:
CN Location:
30-pin crimp
Figure 3-10
See
Page 23
Page 40
See
CN Pinouts:
Table 3-10
NANO-QM770 EPIC SBC
The LVDS connector is for an LCD panel connected to the board.
Figure 3-10: LVDS Connector Location
Pin Description Pin Description
1 GND 2 GND
3 A_Y0 4 A_Y0#
5 A_Y1 6 A_Y1#
7 A_Y2 8 A_Y2#
9 A_CK 10 A_CK#
11 A_Y3 12 A_Y3#
13 GND 14 GND
15 B_Y0 16 B_Y0#
17 B_Y1 18 B_Y1#
19 B_Y2 20 B_Y2#
21 B_CK 22 B_CK#
23 B_Y3 24 B_Y3#
25 GND 26 GND
27 VCC/VCC3 28 VCC/VCC3
29 VCC/VCC3 30 VCC/VCC3
Table 3-10: LVDS Connector Pinouts
Page 24
Page 41
NANO-QM770 EPIC SBC
3.2.9 LVDS Backlight Connector
CN Label: INVERTER1
CN Type:
CN Location:
CN Pinouts:
The backlight inverter connectors provide power to LCD panels.
Figure 3-11: LVDS Backlight Inverter Connector
5-pin wafer
Figure 3-11
See
Table 3-11
See
Pin Description
1
BRIGHTNESS
2
3
4
5
Table 3-11: Backlight Inverter Connector Pinouts
GROUND
+12VS_LCD_BKL
GROUND
BACKLIGHT ENABLE
3.2.10 PCIe Mini Card Slot
CN Label: CN4
CN Type:
CN Location:
CN Pinouts:
PCIe Mini card slot
Figure 3-12
See
Table 3-12
See
Page 25
Page 42
NANO-QM770 EPIC SBC
The PCIe Mini card slot enables a PCIe Mini card expansion module to be connected to
the board. Cards supported include among others wireless LAN (WLAN) cards and IEI
PCIe Mini disk on module (DOM) SSD cards.
Figure 3-12: PCIe Mini Card Slot Location
Pin Description Pin Description
1 PCIE_WAKE# 2 VCC3
3 N/C 4 GND
5 N/C 6 1.5V
7 N/C 8 N/C
9 GND 10 N/C
11 CLK- 12 N/C
13 CLK+ 14 N/C
15 GND 16 N/C
17 PCIRST# 18 GND
19 N/C 20 VCC3
21 GND 22 PCIRST#
23 PERN2 24 3VDual
25 PERP2 26 GND
27 GND 28 1.5V
29 GND 30 SMBCLK
31 PETN2 32 SMBDATA
33 PETP2 34 GND
Page 26
35 GND 36 USBD37 N/C 38 USBD+
39 N/C 40 GND
Page 43
NANO-QM770 EPIC SBC
Pin Description Pin Description
41 N/C 42 N/C
43 N/C 44 N/C
45 N/C 46 N/C
47 N/C 48 1.5V
49 N/C 50 GND
51 N/C 52 VCC3
Table 3-12: PCIe Mini Card Slot Pinouts
3.2.11 Power Connector (12V)
CN Label: PWR1
CN Type:
CN Location:
CN Pinouts:
4-pin connector
Figure 3-13
See
Table 3-13
See
The power connector is connected to an external power supply and supports 12V power
input. Power is provided to the system, from the power supply through this connector.
Figure 3-13: Power Connector Location
Pin Description Pin Description
1 Ground 2 Ground
3 +12V 4 +12V
Table 3-13: Power Connector Pinouts
Page 27
Page 44
3.2.12 RS-232 Serial Port Connectors (COM1, COM2)
CN Label: COM1, COM2
NANO-QM770 EPIC SBC
CN Type:
CN Location:
CN Pinouts:
The 10-pin serial port connectors provide two RS-232 serial communications channels.
The COM serial port connectors can be connected to external RS-232 serial port devices.
Figure 3-14: RS-232 Serial Port Connector Locations
10-pin header
Figure 3-14
See
Table 3-14
See
Pin Description Pin Description
1 -NDCD2 6 -NCTS2
2 -NDSR2 7 -NDTR2
3 NSIN2 8 -XRI2
4 -NRTS2 9 GND
5 NSOUT2 10 GND
Table 3-14: Serial Port Connector Pinouts
3.2.13 RS-422/485 Serial Port Connector (COM3)
CN Label: COM3
4-pin wafer
Figure 3-15
See
Page 28
CN Type:
CN Location:
Page 45
NANO-QM770 EPIC SBC
CN Pinouts:
See
This connector provides RS-422 or RS-485 communications.
Figure 3-15: RS-422/485 Serial Port Connector Location
Pin Description
1 RXD485#
Table 3-15
2 RXD485+
3 TXD485+
4 TXD485#
Table 3-15: RS-422/485 Serial Port Connector Pinouts
Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the D-sub
9 connector are listed below.
RS-422 Pinouts RS-485 Pinouts
Table 3-16: D-sub 9 RS-422/485 Pinouts
3.2.14 SATA Drive Connectors
CN Label: S_ATA1, S_ATA2
CN Type:
7-pin SATA drive connectors
Page 29
Page 46
See
CN Location:
CN Pinouts:
Figure 3-16
Table 3-17
See
NANO-QM770 EPIC SBC
The SATA connectors connect to SATA hard drives or optical drives with data transfer
speeds as high as 6Gb/s.
Figure 3-16: SATA Drive Connector Locations
Pin Description
1 GND
2 TX+
3 TX4 GND
5 RX6 RX+
7 GND
Table 3-17: SATA Drive Connector Pinouts
3.2.15 SATA Power Connectors
CN Label: CN1, CN2
CN Type:
CN Location:
2-pin wafer
Figure 3-17
See
Page 30
Table 3-18
CN Pinouts:
See
Use the SATA Power Connector to connect to SATA device power connections.
Page 47
NANO-QM770 EPIC SBC
Figure 3-17: SATA Power Connector Locations
Pin Description
1 +V5S
2 GND
Table 3-18: SATA Power Connector Pinouts
3.2.16 SMBus Connector
CN Label: CN3
CN Type:
CN Location:
CN Pinouts:
The SMBus (System Management Bus) connector provides low-speed system
management communications.
4-pin wafer
Figure 3-18
See
Table 3-19
See
Figure 3-18: SMBus Connector Location
Page 31
Page 48
Pin Description
1 GND
2 SMB_DATA
3 SMB_CLK
4 +V5S
Table 3-19: SMBus Connector Pinouts
3.2.17 SO-DIMM Connector
CN Label: DIMM1
NANO-QM770 EPIC SBC
CN Type:
CN Location:
204-pin DDR3 SO-DIMM connector
Figure 3-19
See
The SO-DIMM connector is for installing memory on the system.
Figure 3-19: SO-DIMM Connector Location
3.2.18 SPI Flash Connector
Page 32
CN Label: JSPI1
CN Type:
CN Location:
CN Pinouts:
The 6-pin SPI Flash connector is used to flash the BIOS.
6-pin header
Figure 3-20
See
Table 3-20
See
Page 49
NANO-QM770 EPIC SBC
Figure 3-20: SPI Flash Connector Location
Pin Description
+V3.3M_SPI_CON
1
SPI_CS
2
SPI_SO_SW
3
SPI_CLK_SW
4
SPI_SI_SW
5
GND
6
Table 3-20: SPI Flash Connector Pinouts
3.2.19 TPM Connector
CN Label: TPM1
CN Type:
CN Location:
CN Pinouts:
The Trusted Platform Module (TPM) connector secures the system on bootup.
20-pin header
Figure 3-21
See
Table 3-21
See
Page 33
Page 50
NANO-QM770 EPIC SBC
Figure 3-21: TPM Connector Location
Pin Description Pin Description
1 LCLK 2 GND
3 LFRAME# 4 KEY
5 LRERST# 6 +5V
7 LAD3 8 LAD2
9 +3V 10 LAD1
11 LAD0 12 GND
13 SCL 14 SDA
15 SB3V 16 SERIRQ
17 GND 18 GLKRUN#
19 LPCPD# 20 LDRQ#
Table 3-21: TPM Connector Pinouts
3.2.20 USB 2.0 Connector
CN Label: USB1
CN Type:
CN Location:
CN Pinouts:
The USB header can connect to two USB devices.
8-pin header
Figure 3-22
See
Table 3-22
See
Page 34
Page 51
NANO-QM770 EPIC SBC
Figure 3-22: USB Connector Location
Pin Description Pin Description
1 VCC 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA7 GND 8 VCC
Table 3-22: USB Port Connector Pinouts
3.3 External Interface Connectors
Figure 3-23 shows the NANO-QM770 motherboard external interface connectors. The
NANO-QM770 on-board external interface connectors are shown in
Figure 3-23: External Interface Connectors
3.3.1 DVI Connector
CN Label: CON1
Figure 3-23.
CN Type:
DVI connector
Page 35
Page 52
See
CN Location:
CN Pinouts:
The 24-pin Digital Visual Interface (DVI) connector connects to high-speed,
high-resolution digital displays. The DVI-I connector supports both digital and analog
signals.
Figure 3-23
Table 3-23 and Figure 3-24
See
NANO-QM770 EPIC SBC
Pin Description
1 TMDS Data22 TMDS Data2+
3 GND
4 N/C
5 N/C
6 DDC Clock [SCL]
7 DDC Data [SDA]
8 5VSYNC
C1 BR
C2 BG
C3 BB
C4 5HSync
C5 GND
Table 3-23: DVI Connector Pinouts
Pin
9
10
11
12
13
14
15
16
--
--
--
--
--
Description
TMDS Data1TMDS Data1+
GND
NC
NC
5V
GND
HPD
--
--
--
--
--
Pin
17
18
19
20
21
22
23
24
--
--
--
--
--
Description
TMDS Data0TMDS Data0+
GND
NC
NC
GND
TMDS Clock +
TMDS Clock -
--
--
--
--
--
Figure 3-24: DVI-I Connector
3.3.2 Ethernet Connectors
CN Label: LAN1, LAN2
RJ-45
See Figure 3-23
Page 36
CN Type:
CN Location:
Page 53
NANO-QM770 EPIC SBC
CN Pinouts:
See Table 3-24
The LAN connector connects to a local network.
PIN DESCRIPTION PIN DESCRIPTION
1 MDIA3- 5 MDIA2+
2 MDIA3+ 6 MDIA1+
3 MDIA1- 7 MDIA04 MDIA2- 8 MDIA0+
Table 3-24: LAN Pinouts
Figure 3-25: Ethernet Connector
LED Description LED Description
A on: linked
blinking: data is being sent/received
Table 3-25: Connector LEDs
3.3.3 HDMI Connectors
CN Label: HDMI1, HDMI2
CN Type:
CN Location:
CN Pinouts:
The HDMI connector connects to a display device with HDMI interface.
HDMI connector
Figure 3-23
See
Table 3-26 and Figure 3-26
See
B off: 10 Mb/s
green: 100 Mb/s
orange: 1000 Mb/s
Page 37
Page 54
Pin Description Pin Description
1 HDMI_DATA2 13 N/C
2 GND 14 N/C
3 HDMI_DATA2# 15 HDMI_SCL
4 HDMI_DATA1 16 HDMI_SDA
5 GND 17 GND
6 HDMI_DATA1# 18 +5V
7 HDMI_DATA0 19 HDMI_HPD
8 GND 20 HDMI_GND
9 HDMI_DATA0# 21 HDMI_GND
10 HDMI_CLK 22 HDMI_GND
11 GND 23 HDMI_GND
12 HDMI_CLK#
NANO-QM770 EPIC SBC
Table 3-26: HDMI Connector Pinouts
Figure 3-26: HDMI Connector
3.3.4 USB 3.0 Connectors
CN Label: USB_CON1, USB_CON2
CN Type:
CN Location:
CN Pinouts:
The USB 3.0 connector can be connected to a USB device.
USB 3.0 port
See
See
Figure 3-23
Table 3-27
Page 38
Page 55
NANO-QM770 EPIC SBC
Pin Description Pin Description
1 VBUS 2 DATA13 DATA1+ 4 GND
5 SSRX1- 6 SSRX1+
7 GND 8 SSTX19 SSTX1+ 10 VBUS
11 DATA2- 12 DATA2+
13 GND 14 SSRX215 SSRX2+ 16 GND
17 SSTX2- 18 SSTX2+
Table 3-27: USB Port Pinouts
Page 39
Page 56
NANO-QM770 EPIC SBC
Chapter
4
4 Installation
Page 40
Page 57
NANO-QM770 EPIC SBC
4.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during installation may result in
permanent damage to the product and severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the NANO-QM770. Dry climates are especially susceptible to ESD. It is therefore
critical to strictly adhere to the following anti-static precautions whenever the
NANO-QM770, or any other electrical component, is handled.
Wear an anti-static wristband: - Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding:- Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the NANO-QM770, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
NANO-QM770.
Only handle the edges of the PCB:-: When handling the PCB, hold it by the
edges.
4.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before the NANO-QM770 is installed. All
installation notices pertaining to the installation of NANO-QM770
should be strictly adhered to. Failing to adhere to these precautions
may lead to severe damage of the NANO-QM770 and injury to the
person installing the motherboard.
Page 41
Page 58
NANO-QM770 EPIC SBC
WARNING:
The installation instructions described in this manual should be
carefully followed in order to prevent damage to the NANO-QM770,
NANO-QM770 components and injury to the user.
Before and during the installation please DO the following:
Read the user manual:
o The user manual provides a complete description of the installation
instructions and configuration options.
Wear an electrostatic discharge cuff (ESD):
o Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.
Place on an antistatic pa d:
o When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.
Turn all power off:
o Make sure the product is disconnected from all power supplies and that
no electricity is being fed into the system.
Before and during the installation of the NANO-QM770 DO NOT:
DO NOT remove any of the stickers on the PCB board. These stickers are
required for warranty validation.
DO NOT use the product before verifying all the cables and power connectors
are properly connected.
DO NOT allow screws to come in contact with the PCB circuit, co nnector pins,
or its components.
Page 42
Page 59
NANO-QM770 EPIC SBC
4.3 SO-DIMM Installation
To install an SO-DIMM, please follow the steps below and refer to Figure 4-1.
Figure 4-1: SO-DIMM Installation
Step 1: Locate the SO-DIMM socket. Place the board on an anti-static mat.
Step 2: Align the SO-DIMM with the socket. Al ign the notch on the memory with the
notch on the memory socket.
Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See
Step 4: Seat the SO-DIMM. Gently push downwards and the arms clip into place. (See
Figure 4-1)
4.4 PCIe Mini Card Installation
A PCIe Mini card slot is located on the solder side of the NANO-QM770. To install the
PCIe Mini card, please refer to the diagram and instructions below.
Figure 4-1)
Page 43
Page 60
Figure 4-2: PCIe Mini Card Installation
Step 1: Insert into the socket at an angle. Line up the notch on the card with the notch
NANO-QM770 EPIC SBC
on the connector. Slide the PCIe Mini card into the socket at an angle of about
20º.
Step 2: Push down until the card clips into place. Push the other end of the card
down until it clips into place on the plastic connector.Step 0:
4.5 Jumper Settings
NOTE:
A jumper is a metal bridge that is used
to close an electrical circuit. It consists
of two metal pins and a small metal clip
(often protected by a plastic cover) that
slides over the pins to connect them.
To CLOSE/SHORT a jumper means
Page 44
connecting the pins of the jumper with
the plastic clip and to OPEN a jumper means removing the plastic clip
from a jumper.
Page 61
NANO-QM770 EPIC SBC
Before the NANO-QM770 is installed in the system, the jumpers must be set in
accordance with the desired configuration. The jumpers on the NA NO-QM770 a re listed in
Table 4-1.
Description Label Type
AT/ATX mode selection J_ATXCTL1 3-pin header
Clear CMOS J_CMOS1 3-pin header
Clear ME RTC registers ME_RTC1 3-pin header
Flash descriptor security override J_FLASH1 3-pin header
LVDS voltage selection J_VLVDS1 3-pin header
LVDS resolution selection J_PID1 8-pin header
PCIe Mini/mSATA mode selection MSATA_SW 2-pin header
Table 4-1: Jumpers
4.5.1 AT/ATX Mode Selection
Jumper Label: J_ATXCTL1
Jumper Type:
Jumper Settings:
Jumper Location:
Set both of the jumpers select AT or ATX power mode for the NANO-QM770. AT power
mode limits the system to on/off. ATX allows the system to use various power saving
states and enter a standby state, so the system can be turned on remotely over a network.
The settings on both jumpers should be the same.
Pin Description
Short 1-2 ATX mode (Default)
Short 2-3 AT mode
3-pin header
Table 4-2
See
Figure 4-3
See
Table 4-2: AT/ATX Mode Selection Jumper Settings
Page 45
Page 62
Figure 4-3: AT/ATX Mode Selection Jumper Location
4.5.2 Clear CMOS
Jumper Label: J_CMOS1
NANO-QM770 EPIC SBC
Jumper Type:
Jumper Settings:
Jumper Location:
If the NANO-QM770 fails to boot due to improper BIOS settings, the clear CMOS jumper
clears the CMOS data and resets the system BIOS information. To do this, use the jumper
cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1
and 2.
If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault
may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the
following:
Enter the correct CMOS setting
Load Optimal Defaults
Load Failsafe Defaults.
3-pin header
Table 4-3
See
Figure 4-4
See
Page 46
After having done one of the above, save the changes and exit the CMOS Setup menu.
The clear CMOS jumper settings are shown in
Table 4-3.
Page 63
NANO-QM770 EPIC SBC
Pin Description
Short 1-2 Keep CMOS Setup (Default)
Short 2-3 Clear CMOS Setup
Table 4-3: Clear CMOS Jumper Settings
Figure 4-4: Clear CMOS Jumper Location
4.5.3 Clear ME RTC Registers
Jumper Label: ME_RTC1
Jumper Type:
Jumper Settings:
Jumper Location:
3-pin header
See
See
Table 4-4
Figure 4-5
Resets the RTC registers used for the Intel® Management Engine when the on-board
battery is changed.
Pin Description
Short 1-2 Save ME RTC registers (Default)
Short 2-3 Clear ME RTC registers
Table 4-4: Clear ME RTC Registers Jumper Settings
Page 47
Page 64
Figure 4-5: Clear ME RTC Registers Jumper Location
4.5.4 Flash Descriptor Security Override
Jumper Label: J_FLASH1
NANO-QM770 EPIC SBC
Jumper Type:
Jumper Settings:
Jumper Location:
The Flash Descriptor Security Override jumper specifies whether to override the flash
descriptor.
Setting Description
Short 1-2 No override
Short 2-3 Override
Table 4-5: Flash Descriptor Security Override Jumper Settings
3-pin header
Table 4-5
See
Figure 4-6
See
Page 48
Figure 4-6: Flash Descriptor Security Override Jumper Location
Page 65
NANO-QM770 EPIC SBC
4.5.5 LVDS Voltage Selection
Jumper Label: J_VLVDS1
Jumper Type:
Jumper Settings:
Jumper Location:
Selects the voltage of the LVDS connector.
Pin Description
Short 1-2 +3.3 V (Default)
Short 2-3 +5 V
Table 4-6: LVDS Voltage Selection Jumper Settings
3-pin header
Table 4-6
See
Figure 4-7
See
Figure 4-7: LVDS Voltage Selection Jumper Location
4.5.6 LVDS Resolution Selection
Jumper Label: J_PID1
Jumper Type:
Jumper Settings:
Jumper Location:
Selects the resolution of the LCD panel connected to the LVDS connector.
Pin Description
OPEN 640 X 480 (18bit)
1-2 800 X 600 (18bit)
8-pin header
Table 4-7
See
Figure 4-8
See
Page 49
Page 66
Pin Description
3-4 1024 X 768 (18bit)
1-2 & 3-4 1024 X 768 (24bit) Default
5-6 1280 X 800 (24bit)
1-2 & 5-6 1280 X 1024 (48bit)
3-4 & 5-6 1366 X 768 (24bit)
1-2 & 3-4 & 5-6 1440 X 900 (48bit)
7-8 1400 X 1050 (48bit)
1-2 & 7-8 1600 X 900 (48bit)
3-4 & 7-8 1600 X 1200 (48bit)
1-2 & 3-4 & 7-8 1680 X 1050 (48bit)
5-6 & 7-8 1920 X 1080 (48bit)
1-2 & 5-6 & 7-8 1920 X 1200 (48bit)
3-4 & 5-6 & 7-8 2048 X 1536 (48bit)
NANO-QM770 EPIC SBC
1-2 & 3-4 & 5-6 & 7-8 LVDS disabled
Table 4-7: LVDS Screen Resolution Jumper Settings
Figure 4-8: LVDS Resolution Selection Jumper Location
4.5.7 PCIe Mini/mSATA Mode Selection
Jumper Label: MSATA_SW
Jumper Type:
Jumper Settings:
2-pin header
Table 4-8
See
Page 50
Figure 4-9
Jumper Location:
See
Sets the PCIe Mini slot (M_PCIE1) as the PCIe Mini card slot or mSATA drive slot.
Page 67
NANO-QM770 EPIC SBC
Pin Description
Closed PCIe Mini (Default)
Open mSATA
Table 4-8: PCIe Mini/mSATA Mode Selection Jumper Settings
Figure 4-9: PCIe Mini/mSATA Mode Selection Jumper Location
4.6 Chassis Installation
4.6.1 Airflow
WARNING:
Airflow is critical for keeping components within recommended
operating termperatures. The chassis should have fans and vents as
necessary to keep things cool.
The NANO-QM770 must be installed in a chassis with ventilation holes on the sides
allowing airflow to travel through the heat sink surface. In a system with an individual
power supply unit, the cooling fan of a power supply can also help generate airflow
through the board surface.
4.6.2 Motherboard Installation
To install the NANO-QM770 motherboard into the chassis please refer to the reference
material that came with the chassis.
Page 51
Page 68
4.7 Internal Peripheral Device Connections
This section outlines the installation of peripheral devices to the onboard connectors.
4.7.1 AT Power Connection
Follow the instructions below to connect the NANO-QM770 to an AT power supply.
WARNING:
Disconnect the power supply power cord from its AC power source to
prevent a sudden power surge to the NANO-QM770.
Step 1: Locate the power cable. The power cable is shown in the packing list in
Chapter 2.
NANO-QM770 EPIC SBC
Step 2: Connect the Power Cable to the Motherboard. Connect the 4-pin (2x2) Molex
type power cable connector to the AT power connector on the motherboard. See
Figure 4-10.
Page 52
Figure 4-10: Power Cable to Motherboard Connection
Page 69
NANO-QM770 EPIC SBC
Step 3: Connect Power Cable to Power Supply. Connect one of the 4-pin (1x4) Molex
type power cable connectors to an AT power supply. See
Figure 4-11: Connect Power Cable to Power Supply
Figure 4-11.
4.7.2 Audio Kit Installation
The Audio Kit that came with the NANO-QM770 connects to the audio connector on the
NANO-QM770. The audio kit consists of three audio jacks. Mic-in connects to a
microphone. Line-in provides a stereo line-level input to connect to the output of an audio
device. Line-out, a stereo line-level output, connects to two amplified speakers. To install
the audio kit, please refer to the steps below:
Step 1: Locate the audio connector. The location of the 10-pin audi o connector is
shown in Chapter 3.
Step 2: Align pin 1. Align pin 1 on the on-board connector with pin 1 on the audio kit
connector. Pin 1 on the audio kit connector is indicated with a white dot. See
Figure 4-12.
Page 53
Page 70
NANO-QM770 EPIC SBC
Figure 4-12: Audio Kit Cable Connection
Step 3: Connect the audio devices. Connect speakers to the line-out audio jack.
Connect the output of an audio device to the line-in audio jack. Connect a
microphone to the mic-in audio jack.Step 0:
4.7.3 SATA Drive Connection
The NANO-QM770 is shipped with two SATA drive cable. To connect the SATA drive to
the connector, please follow the steps below.
Step 1: Locate the SA TA connector and the SATA p ower connector. The locations of
the connectors are shown in Chapter 3.
Step 2: Insert the cable connector. Insert the cable connector into the on-board SATA
drive connector and the SATA power connector. See
Figure 4-13.
Page 54
Page 71
NANO-QM770 EPIC SBC
Figure 4-13: SATA Drive Cable Connection
Step 3: Connect the cable to the SATA disk. Connect the connector on the other end
of the cable to the connector at the back of the SATA drive. See
Step 4: To remove the SATA cable from the SATA connector, press the clip on the
connector at the end of the cable. Step 0:
Figure 4-13.
4.7.4 Single RS-232 Cable (w/o Bracket)
The single RS-232 cable consists of one serial port connector attached to a serial
communications cable that is then attached to a D-sub 9 male connector. To install the
single RS-232 cable, please follow the steps below.
Step 1: Locate the connector. The location of the RS-232 conne ctor is shown in
Chapter 3.
Step 2: Insert the cable connector. Insert the connector into the serial port pin header.
Figure 4-14. A key on the front of the cable connectors ensures the
See
connector can only be installed in one direction.
Page 55
Page 72
Figure 4-14: Single RS-232 Cable Installation
Step 3: Secure the bracket. The single RS-232 connector has two retention scre ws
NANO-QM770 EPIC SBC
that must be secured to a chassis or bracket.
Step 4: Connect the serial device. Once the single RS-232 connector is connected to
a chassis or bracket, a serial communications device can be connected to the
system. Step 0:
4.8 External Peripheral Interface Connection
Devices can be connected to the external connectors. To install external devices, follow
the directions in the subsections below.
4.8.1 DVI Display Device Connection
The NANO-QM770 has a single female DVI-I connector on the external peripheral
interface panel. The DVI-I connector is connected to a digital display device. To connect a
digital display device to the NANO-QM770, please follow the instructions below.
Step 1: Locate the DVI-I connector. The location of the DVI-I connector is shown in
Page 56
another chapter.
Page 73
NANO-QM770 EPIC SBC
Step 2: Align the DVI-I connector. Align the male DVI-I connector on the digital display
device cable with the female DVI-I connector on the external peripheral
interface.
Step 3: Insert the DVI-I connector. Once the connectors are properly aligned with the
male connector, insert the male conne ctor from the digital display device into the
female connector on the NANO-QM770. See
Figure 4-15: DVI Connector
Figure 4-15.
Step 4: Secure the connector. Secure the DVI-I conne ctor from the digital display
device to the external interface by tightening the two retention screws on either
side of the connector. Step 0:
4.8.2 HDMI Display Device Connection
The HDMI connector transmits a digital signal to compatible HDMI display devices such
as a TV or computer screen. To connect the HDMI cable to the NANO-QM770, follow the
steps below.
Step 1: Locate the HDMI connector. The location is shown in Chapter 3.
Page 57
Page 74
Step 2: Align the connector. Alig n the HDMI connector with the HDMI port. Make sure
the orientation of the connector is correct.
NANO-QM770 EPIC SBC
Figure 4-16: HDMI Connection
Step 3: Insert the HDMI connector. Gently insert the HDMI connector. The connector
should engage with a gentle push. If the connector does not insert easily, check
again that the connector is aligned correctly, and that the connector is being
inserted with the right way up. Step 0:
4.8.3 LAN Connection
There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection
to an external network. To connect a LAN cable with an RJ-45 connector, please follow
the instructions below.
Step 1: Locate the RJ-45 connectors. The locations of the LAN connectors are shown
in Chapter 3.
Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of
Page 58
the RJ-45 connectors on the NANO-QM770. See
Figure 4-17.
Page 75
NANO-QM770 EPIC SBC
Figure 4-17: LAN Connection
Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN
cable RJ-45 connector into the on-board RJ-45 connector. Step 0:
4.8.4 USB Connection
The external USB 3.0 connectors provide easier and quicker access to external USB
devices. Follow the steps below to connect USB devices to the NANO-QM770.
Step 1: Locate the USB 3.0 connectors. The locations of the USB 3.0 conne ctors are
shown in Chapter 3.
Step 2: Insert a USB 3.0 plug. Insert the USB 3.0 plug of a device into the USB 3.0 on
the external peripheral interface. See
Figure 4-18. Step 0:
Page 59
Page 76
Figure 4-18: USB Connector
NANO-QM770 EPIC SBC
4.9 Intel® AMT Setup Procedure
The NANO-QM770 is featured with the Intel® Active Management Technology (AMT). To
enable the Intel® AMT function, follow the steps below.
Step 1: Make sure the DIMM1 socket is installed with one DDR3 SO-DIMM.
Step 2: Connect an Ethernet cable to the RJ-45 connector labeled LAN1.
Step 3: The AMI BIOS options regarding the Intel® ME or Intel® AMT must be enabled,
Step 4: Properly install the Intel® Management Engine Components drivers from the
iAMT Driver & Utility directory in the driver CD. See Section
Step 5: Configure the Intel® Management Engine BIOS extension (MEBx). To get into
the Intel® MEBx settings, press <Ctrl+P> after a single beep during boot-up
process. Enter the Intel® current ME password as it requires (the Intel® default
password is admin).
6.9.
Page 60
Page 77
NANO-QM770 EPIC SBC
NOTE:
To change the password, enter a new password following the strong
password rule (containing at least one upper case letter, one lower
case letter, one digit and one special character, and be at least eight
characters).
Page 61
Page 78
NANO-QM770 EPIC SBC
Chapter
5
5 BIOS
Page 62
Page 79
NANO-QM770 EPIC SBC
5.1 Introduction
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
NOTE:
Some of the BIOS options may vary throughout the life cycle of the
product and are subject to change without prior notice.
5.1.1 Starting Setup
The UEFI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the D
2. Press the D
appears on the screen. 0.
If the message disappears before the D
and try again.
ELETE or F2 key as soon as the system is turned on or
ELETE or F2 key when the “Press Del to enter SETUP” message
ELETE or F2 key is pressed, restart the computer
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press E
keys are shown in.
Key Function
Up arrow Move to the item above
SC to quit. Navigation
Down arrow Move to the item below
Left arrow Move to the item on the left hand side
Right arrow Move to the item on the right hand side
Page 63
Page 80
Key Function
+ Increase the numeric value or make changes
- Decrease the numeric value or make changes
Page up Move to the next page
Page down Move to the previous page
Esc Main Menu – Quit and do not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
F1 General help, only for Status Page Setup Menu and Option
Page Setup Menu
F9 Load optimized defaults
F10 Save changes and Exit BIOS
NANO-QM770 EPIC SBC
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press E
the F1 key again.
5.1.4 Unable to Reboot After Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 4.
5.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
SC or
Page 64
Main – Changes the basic system configuration.
Advanced – Changes the advanced system settings.
Chipset – Changes the chipset settings.
Boot – Changes the system boot configuration.
Page 81
S
NANO-QM770 EPIC SBC
Security – Sets User and Supervisor Passwords.
Save & Exit – Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
5.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
BIOS Information
BIOS Vendor American Megatrends
Core Version 4.6.5.3 0.18
Compliency UEFI 2.3; PI 1.2
Project Version B208AR01.ROM
Build Date 05/10/2012 10:09:44
System Date [Tue 01/02/2012]
System Time [14:20:27]
Access Level Administrator
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
switch between Date
elements.
----------------------
ÅÆ
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save
ESC Exit
et the Date. Use Tab to
: Select Screen
BIOS Menu 1: Main
Î BIOS Information
The BIOS Information lists a brief summary of the BIOS. The fields in BIOS Information
cannot be changed. The items shown in the system overview include:
BIOS Vendor: Installed BIOS vendor
Core Version: Current BIOS version
Project Version: the bo ard version
Build Date and Time: Date and time the current BIOS version was made
The System Overview field also has two user configurable fields:
Page 65
Page 82
Î System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
Î System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
5.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING!
NANO-QM770 EPIC SBC
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
> ACPI Settings
> RTC Wake Settings
> Trusted Computing
> CPU Configuration
> SATA Configuration
> Intel(R) Rapid Start Technology
> Intel TXT(LT) Configuration
> AMT Configuration
> USB Configuration
> F81866 Super IO Configuration
> F81866 H/M Monitor
> Serial Port Console Redirection
> iEi Feature
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
System ACPI Parameters
----------------------
ÅÆ
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save
ESC Exit
: Select Screen
Page 66
BIOS Menu 2: Advanced
Page 83
w
NANO-QM770 EPIC SBC
5.3.1 ACPI Configuration
The ACPI Configuration menu (BIOS Menu 3) configures the Advanced Configuration
and Power Interface (ACPI) options.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
ACPI Settings
ACPI Sleep State [S1 only (CPU Stop C…]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Select ACPI sleep state
the system will enter
hen the SUSPEND button
is pressed.
----------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save
ESC Exit
BIOS Menu 3: ACPI Configuration
Î ACPI Sleep State [S1 only (CPU Stop Clock)]
Use the ACPI Sleep State option to specify the sleep state the system enters when it is
not being used.
Î
S1 only (CPU Stop
Clock)
Î
S3 only (Suspend
to RAM)
DEFAULT
The system enters S1(POS) sleep state. The
system appears off. The CPU is stopped; RAM is
refreshed; the system is running in a low power
mode.
The caches are flushed and the CPU is powered
off. Power to the RAM is maintained. The
computer returns slower to a working state, but
more power is saved.
Page 67
Page 84
E
w
NANO-QM770 EPIC SBC
5.3.2 RTC Wake Settings
The RTC Wake Settings menu (BIOS Menu 4) configures RTC wake event.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Wake system with Fixed Time [Disabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
nable or disable System
ake on alarm event. When
enabled, System will
wake on the
dat::hr::min::sec
specified
----------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save
ESC Exit
BIOS Menu 4: RTC Wake Settings
Î Wake System with Fixed Time [Disabled]
Use the Wake System with Fixed Time option to specify the time the system should be
roused from a suspended state.
Î
Disabled DEFAULT
The real time clock (RTC) cannot generate a wake
event
Page 68
Page 85
E
I
NANO-QM770 EPIC SBC
Î
Enabled
If selected, the following appears with values that
can be selected:
*Wake up every day
*Wake up date
*Wake up hour
*Wake up minute
*Wake up second
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
5.3.3 Trusted Computing
Use the Trusted Computing menu (BIOS Menu 5) to configure settings related to the
Trusted Computing Group (TCG) Trusted Platform Module (TPM).
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Configuration
Security Device Support [Disable]
Current Status Information
NO Security Device Found
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 5: Trusted Computing
nables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
NT1A interface will not
be available.
----------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
Page 69
Page 86
a
T
D
Î Security Device Support [Disable]
Use the Security Device Support option to configure support for the TPM.
NANO-QM770 EPIC SBC
Î
Disable DEFAULT
Î
Enable
TPM support is disabled.
TPM support is enabled.
5.3.4 CPU Configuration
Use the CPU Configuration menu (BIOS Menu 6) to view detailed CPU specifications
and configure the CPU.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
CPU Configuration
Intel(R) Core(TM) i7-3610QE CPU @ 2.30GHz
CPU Signature 306a9
Microcode Patch c
Max CPU Speed 2300 MHz
Min CPU Speed 1200 MHz
CPU Speed 2300 MHz
Processor Cores 4
Intel HT Technology Supported
Intel VT-x Technology Supported
Intel SMX Technology Supported
6-bit Supported
L1 Data Cache 32 KB x 4
L1 Code Cache 32 KB x 4
L2 Cache 256 KB x 4
L3 Cache 6144 KB
Hyper-Threading [Enabled]
Intel Virtualization Technology [Disabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enabled for Windows XP
nd Linux (OS optimized
for Hyper-Threading
echnology) and Disabled
for other OS (OS not
optimized for
Hyper-Threading
Technology). When
isabled only one thread
per enabled fore is
enabled.
----------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 6: CPU Configuration
The CPU Configuration menu (
Processor Type: Lists the brand name of the CPU being used
CPU Signature: Lists the CPU signature value.
Microcode Patch: Lists the microcode patch being used.
Page 70
BIOS Menu 6) lists the following CPU details:
Page 87
NANO-QM770 EPIC SBC
Max CPU Speed: Lists the maximum CPU processing speed.
Min CPU Speed: Lists the minimum CPU processing speed.
CPU Speed: Lists the CPU processing speed
Processor Core: Lists the number of the processor cores
Intel HT Technology: Indicates if Intel HT Technology is supported by the
CPU.
Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the
CPU.
Intel SMX Technology: Indicates if Intel SMX Technology is supported by the
CPU.
64-bit: Indicates if 64-bit is supported by the CPU.
L1 Data Cache: Lists the amount of data storage space on the L1 cache.
L1 Code Cache: Lists the amount of code storage space on the L1 cache.
L2 Cache: Lists the amount of storage space on the L2 cache.
L3 Cache: Lists the amount of storage space on the L3 cache.
Î Hyper Threading [Enabled]
Use the Hyper Threading to enable or disable the CPU hyper threading function.
Î
Disabled
Î
Enabled DEFAULT
Î Intel Virtualization Technology [Disabled]
Use the Intel Virtualization Technology option to enable or disable virtualization on the
system. When combined with third party software, Intel Virtualization technology allows
several OSs to run on the same system at the same time.
Î
Disabled DEFAULT
Disables the use of hyper threading technology
Enables the use of hyper threading technology
Disables Intel Virtualization
Technology.
Î
Enabled
Enables Intel Virtualization Technology.
Page 71
Page 88
NANO-QM770 EPIC SBC
5.3.5 SATA Configuration
Use the SATA Configuration menu (BIOS Menu 7) to change and/or set the
configuration of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
SATA Mode Selection [AHCI]
Serial ATA Port0 Empty
Software Preserve Unknown
Hot Plug [Disabled]
Serial ATA Port1 Empty
Software Preserve Unknown
Hot Plug [Disabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Determines how SATA
controller(s) operate.
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 7: SATA Configuration
Î SATA Mode Selection [AHCI]
Use the SATA Mode Selection option to configure SATA devices as normal IDE devices.
Î
IDE
Î
AHCI DEFAULT
Î
RAID
Î Hot Plug [Disabled]
Use the Hot Plug option to enable or disable the hot plug function.
Î
Disabled DEFAULT
Î
Enabled
Configures SATA devices as normal IDE device.
Configures SATA devices as AHCI device.
Configures SATA devices as RAID device.
Disables the hot plug function.
Enables the hot plug function.
Page 72
Page 89
NANO-QM770 EPIC SBC
5.3.6 Intel(R) Rapid Start Technology
Use the Intel(R) Rapid Start Technology menu to configure Intel® Rapid Start
Technology support.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel(R) Rapid Start Technology [Disabled]
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 8: Intel(R) Rapid Start Technology
Î Intel(R) Rapid Start Technology [Disabled]
Use Intel(R) Rapid Start Technology option to enable or disable the Intel® Rapid Start
Technology function.
Î
Disabled DEFAULT
Î
Enabled
Intel® Rapid Start Technology is disabled
Intel® Rapid Start Technology is enabled
5.3.7 Intel TXT(LT) Configuration
Use the Intel TXT(LT) Configuration menu to configure Intel® Trusted Execution
Technology support.
Page 73
Page 90
E
T
I
a
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel Trusted Execution Technology Configuration
Intel TXT support only can be enabled/disabled if SMX
is enabled. VT and VT-d support must also be enabled prior
to TXT.
Secure Mode Extensons (SMX) Disabled
Intel TXT(LT) Support [Disabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 9: Intel TXT(LT) Configuration
NANO-QM770 EPIC SBC
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
5.3.8 AMT Configuration
The AMT Configuration menu (BIOS Menu 10) allows the advanced power
management options to be configured.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel AMT [Enabled]
Unconfigure AMT/ME [Disabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enable/Disable Intel (R)
Active Management
Technology BIOS
xtension. Note: iAMT H/W
is always enabled.
his option just controls
the BIOS extension
execution.
f enabled, this requires
dditional firmware in the
SPI device.
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save
ESC Exit
BIOS Menu 10: AMT Configuration
Page 74
Page 91
d
NANO-QM770 EPIC SBC
Î Intel AMT [Enabled]
Use Intel AMT option to enable or disable the Intel® AMT function.
Î
Disabled
Î
Enabled DEFAULT
Î Unconfigure ME [Disabled]
Use the Unconfigure ME option to perform ME unconfigure without password operation.
Î
Disabled DEFAULT
Î
Enabled
Intel® AMT is disabled
Intel® AMT is enabled
Not perform ME unconfigure
To perform ME unconfigure
5.3.9 USB Configuration
Use the USB Configuration menu (BIOS Menu 11) to read USB configuration
information and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices:
1 Keyboard, 2 Hubs
Legacy USB Support [Enabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enables Legacy USB
support. AUTO option
isables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 11: USB Configuration
Page 75
Page 92
S
Î USB Devices
The USB Devices Enabled field lists the USB devices that are enabled on the system
Î Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.
NANO-QM770 EPIC SBC
Î
Enabled DEFAULT
Î
Disabled
Î
Auto
Legacy USB support enabled
Legacy USB support disabled
Legacy USB support disabled if no USB devices are
connected
5.3.10 F81866 Super IO Configuration
Use the F81866 Super IO Configuration menu (BIOS Menu 12) to set or change the
configurations for the FDD controllers, parallel ports and serial ports.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
F81866 Super IO Configuration
F81866 Super IO Chip F81866
> Serial Port 1 Configuration
> Serial Port 2 Configuration
> Serial Port 3 Configuration
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
et Parameters of Serial
Port 1 (COMA)
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 12: Super IO Configuration
Page 76
Page 93
E
NANO-QM770 EPIC SBC
5.3.10.1 Serial Port n Configuration
Use the Serial Port n Configuration menu (BIOS Menu 13) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Serial Port 1 Configuration
Serial Port [Enabled]
Device Settings IO=3F8h; IRQ=4
Change Settings [Auto]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
nable or Disable Serial
Port (COM)
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 13: Serial Port n Configuration Menu
5.3.10.1.1 Serial Port 1 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Î
Enabled DEFAULT
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto DEFAULT
Disable the serial port
Enable the serial port
The serial port IO port address and interrupt address
are automatically detected.
Î
IO=3F8h;
IRQ=4
Serial Port I/O port address is 3F8h and the interrupt
address is IRQ4
Page 77
Page 94
NANO-QM770 EPIC SBC
Î
IO=3F8h;
IRQ=3, 4
Î
IO=2F8h;
IRQ=3, 4
Î
IO=3E8h;
IRQ=3, 4
Î
IO=2E8h;
IRQ=3, 4
5.3.10.1.2 Serial Port 2 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Serial Port I/O port address is 3E8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 3E8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2E8h and the interrupt
address is IRQ3, 4
Disable the serial port
Î
Enabled DEFAULT
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto DEFAULT
Î
Î
Î
Î
IO=2F8h;
IRQ=3
IO=3F8h;
IRQ=3, 4
IO=2F8h;
IRQ=3, 4
IO=3E8h;
Enable the serial port
The serial port IO port address and interrupt address
are automatically detected.
Serial Port I/O port address is 2F8h and the interrupt
address is IRQ3
Serial Port I/O port address is 3F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 3E8h and the interrupt
Page 78
IRQ=3, 4
address is IRQ3, 4
Page 95
NANO-QM770 EPIC SBC
Î
IO=2E8h;
IRQ=3, 4
5.3.10.1.3 Serial Port 3 Configuration
Î Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Disabled
Î
Enabled DEFAULT
Î Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto DEFAULT
Serial Port I/O port address is 2E8h and the interrupt
address is IRQ3, 4
Disable the serial port
Enable the serial port
The serial port IO port address and interrupt address
Î
Î
Î
Î
Î
Î
IO=3E8h;
IRQ=5
IO=3F8h;
IRQ=3, 4
IO=2F8h;
IRQ=3, 4
IO=3E8h;
IRQ=5, 7
IO=2E8h;
IRQ=5, 7
IO=2E0h;
IRQ=5, 7
are automatically detected.
Serial Port I/O port address is 3E8h and the interrupt
address is IRQ5
Serial Port I/O port address is 3F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 2F8h and the interrupt
address is IRQ3, 4
Serial Port I/O port address is 3E8h and the interrupt
address is IRQ5, 7
Serial Port I/O port address is 2E8h and the interrupt
address is IRQ5, 7
Serial Port I/O port address is 2E0h and the interrupt
address is IRQ5, 7
Page 79
Page 96
NANO-QM770 EPIC SBC
5.3.11 F81866 H/W Monitor
The F8186 H/W Monitor menu (BIOS Menu 14) shows the operating temperature, fan
speeds and system voltages.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
PC Health Status
CPU temperature :+62 C
Accuracy: 1. -5~ +10 degree around 100 degree.
2. -10~ +15 degree around 50 degree.
System temperature :+37 C
CPU Fan Speed :2325 RPM
SYS Fan Speed :N/A
+5VS :+5.171 V
+V12S :+12.056 V
+V1.5 :+1.632 V
VSB5V :+5.016 V
VCC3V :+3.360 V
VSB3V :+3.344 V
VBAT :+3.312 V
> Smart Fan Mode Configuration
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Smart Fan Mode Select
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 14: Hardware Health Configuration
Î PC Health Status
The following system parameters and values are shown. The system parameters that are
monitored are:
System Temperatures:
o CPU Temperature
o System Temperature
Fan Speeds:
o CPU Fan Speed
o System Fan Speed
Voltages:
o +5VS
o +V12S
o +V1.5
Page 80
Page 97
NANO-QM770 EPIC SBC
o VSB5V
o VCC3V
o VSB3V
o VBAT
5.3.11.1 Smart Fan Mode Configuration
Use the Smart Fan Mode Configuration submenu (BIOS Menu 15) to configure the
smart fan temperature and speed settings.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
Smart Fan Mode Configuration
CPU_FAN1 Smart Fan Control [Auto Duty-Cycle Mode]
CPU Temperature 1 60
CPU Temperature 2 50
CPU Temperature 3 40
CPU Temperature 4 30
SYS_FAN1 Smart Fan Control [Auto Duty-Cycle Mode]
System Temperature 1 60
System Temperature 2 50
System Temperature 3 40
System Temperature 4 30
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Smart Fan Mode Select
(Reference System
Temperature)
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1 General Help
F2 Previous Values
F3 Optimized Defaults
F4 Save & Exit
ESC Exit
BIOS Menu 15: FAN 1 Configuration
Î CPU_FAN1 Smart Fan Control [Auto Duty-Cycle Mode]
Use the CPU_FAN1 Smart Fan Control option to configure the CPU Smart Fan
(CPU_FAN1).
Î
Manual Duty
Mode
Î
Auto Duty-Cycle
Mode
The fan spins at the speed set in Manual by Duty
Cycle settings
The fan adjusts its speed using Auto by
Duty-Cycle settings
Page 81
Page 98
Î SYS_FAN1 Smart Fan Control [Auto Duty-Cycle Mode]
Use the SYS_FAN1 Smart Fan Control option to configure the System Smart Fan
(SYS_FAN1).
NANO-QM770 EPIC SBC
Î
Manual Duty
Mode
Î
Auto Duty-Cycle
Mode
Î Temperature n
Use the + or – key to change the fan Temperature n value. Enter a decimal number
between 0 and 85.
The fan spins at the speed set in Manual by Duty
Cycle settings
The fan adjusts its speed using Auto by
Duty-Cycle settings
5.3.12 Serial Port Console Redirection
The Serial Port Console Redirection menu (BIOS Menu 16) allows the console
redirection options to be configured. Console redirection allows users to maintain a
system remotely by re-directing keyboard input and text output through the serial port.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
COM1
Console Redirection [Disabled]
> Console Redirection Settings
COM2
Console Redirection [Disabled]
> Console Redirection Settings
COM2(Pci Bus0, Dev22,Func3)
Console Redirection [Disabled]
> Console Redirection Settings
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Console Redirection
Enable or Disable
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
Page 82
BIOS Menu 16: Serial Port Console Redirection
Page 99
c
NANO-QM770 EPIC SBC
Î Console Redirection [Disabled]
Use Console Redirection option to enable or disable the console redirection fun ction.
Î
Disabled DEFAULT
Î
Enabled
Disabled the console redirection function
Enabled the console redirection function
5.3.13 IEI Feature
Use the IEI Feature menu (BIOS Menu 17) to configure One Key Recovery function.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Advanced
iEi Feature
Auto Recovery Function [Disabled]
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Auto Recovery Function
Reboot and recover
system automatically
within 10 min, when OS
rashes. Please install
Auto Recovery API
service before enabling
this function
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
BIOS Menu 17: IEI Feature
Î Auto Recovery Function [Disabled]
Use the Auto Recovery Function BIOS option to enable or disable the auto recovery
function of the IEI One Key Recovery.
Î
Disabled DEFAULT
Î
Enabled
Auto recovery function disabled
Auto recovery function enabled
Page 83
Page 100
NANO-QM770 EPIC SBC
5.4 Chipset
Use the Chipset menu (BIOS Menu 18) to access the Hostbridge and Southbridge
configuration menus.
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
> PCH-IO Configuration
> System Agent (SA) Configuration
Host Bridge Parameters
---------------------
ÅÆ
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
: Select Screen
Page 84
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
BIOS Menu 18: Chipset
Loading...