IEI Technology KINO-PV-D5252, KINO-PV-D4252 User Manual

Download

Page 1

KINO-PV-D5252/D4252 Mini ITX SBC

MODEL:

KINO-PV-D5252/D4252

Mini ITX SBC with Intel® Atom™ Processor D425/D525, DDR3

VGA, Dual LVDS, Dual GbE LAN, USB 2.0, SATA 3Gb/s, RoHS

User Manual

Rev. 1.11 – November 6, 2015

Page i

Page 2

KINO-PV-D5252/D4252 Mini ITX SBC

Revision

Date Version Changes

November 6, 2015 1.11 Changed J2 to JP4

May 29, 2015 1.10 Updated for R11 version

January 17, 2012 1.02 Minor update to Figure 1.4 Data flow Block Diagram

Minor update to Figure 3-1: Connector and Jumper Locations Updated Table D-1 Digital I/O Connector Pinouts

June 17, 2011 1.01 Added KEY1 connector. Minor update to J_VLVDS1 and

J_VLVDS2 jumper settings.

March 24, 2011 1.00 Initial release

Page ii

Page 3

KINO-PV-D5252/D4252 Mini ITX SBC

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners.

Page iii

Page 4

KINO-PV-D5252/D4252 Mini ITX SBC

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnin gs should be taken seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes.

HOT SURFACE

This symbol indicates a hot surface that should not be touched without taking care.

Page iv

Page 5

KINO-PV-D5252/D4252 Mini ITX SBC

Table of Contents

1 INTRODUCTION.......................................................................................................... 1

1.1 INTRODUCTION........................................................................................................... 2

1.2 CONNECTORS ............................................................................................................. 3

1.3 DIMENSIONS............................................................................................................... 4

1.4 DATA FLOW................................................................................................................ 5

1.5 TECHNICAL SPECIFICATIONS ...................................................................................... 6

2 UNPACKING................................................................................................................. 8

2.1 ANTI-STATIC PRECAUTIONS ........................................................................................ 9

2.2 UNPACKING PRECAUTIONS......................................................................................... 9

2.3 PACKING LIST........................................................................................................... 10

2.3.1 Optional Items...................................................................................................11

3 CONNECTORS ........................................................................................................... 12

3.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 13

3.1.1 KINO-PV-D5252/D4252 Layout...................................................................... 13

3.1.2 Peripheral Interface Connectors ..................................................................... 14

3.1.3 External Interface Panel Connectors............................................................... 15

3.2 INTERNAL PERIPHERAL CONNECTORS...................................................................... 15

3.2.1 12V Power Connector...................................................................................... 15

3.2.2 Battery Connector............................................................................................ 16

3.2.3 CompactFlash® Slot........................................................................................ 17

3.2.4 Digital I/O Connector...................................................................................... 19

3.2.5 Fan Connector (CPU)...................................................................................... 20

3.2.6 Fan Connector................................................................................................. 21

3.2.7 Flash SPI ROM................................................................................................ 22

3.2.8 Front Panel Connector.................................................................................... 23

3.2.9 Keyboard/Mouse Connector............................................................................ 24

3.2.10 Keypad Connector ......................................................................................... 24

3.2.11 LVDS1 Connector (For Intel® Atom™ processor D525 dual LVDS only)... 25

Page v

Page 6

3.2.12 LVDS1 Backlight Inverter Connector............................................................ 27

3.2.13 LVDS2 Connector.......................................................................................... 28

3.2.14 LVDS2 Backlight Inverter Connector............................................................ 29

3.2.15 Parallel Port Connector ................................................................................ 29

3.2.16 PCIe Mini Card Slot ...................................................................................... 31

3.2.17 SATA Drive Connectors ................................................................................. 32

3.2.18 SATA Power Connectors................................................................................ 33

3.2.19 Serial Port Connectors (RS-232)................................................................... 35

3.2.20 Serial Port Connector (RS-232)..................................................................... 36

3.2.21 SMBus Connector .......................................................................................... 37

3.2.22 USB Connectors............................................................................................. 38

3.3 EXTERNAL PERIPHERAL INTERFACE CONNECTOR PANEL ......................................... 39

3.3.1 Audio Connector .............................................................................................. 40

3.3.2 Ethernet and USB Connector........................................................................... 40

KINO-PV-D5252/D4252 Mini ITX SBC

3.3.3 Power Connector............................................................................................. 42

3.3.4 Serial Port Connector...................................................................................... 42

3.3.5 VGA Port Connector........................................................................................ 43

4 INSTALLATION ......................................................................................................... 45

4.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 46

4.2 INSTALLATION CONSIDERATIONS.............................................................................. 47

4.2.1 Installation Notices.......................................................................................... 47

4.3 UNPACKING.............................................................................................................. 48

4.4 SO-DIMM INSTALLATION ....................................................................................... 48

4.4.1 SO-DIMM Installation..................................................................................... 49

4.5 COMPACTFLASH® INSTALLATION ............................................................................ 50

4.6 JUMPER SETTINGS .................................................................................................... 51

4.6.1 AT /ATX Power Select Jumper Settings............................................................ 52

4.6.2 Clear CMOS Jumper........................................................................................ 53

4.6.3 CompactFlash® Card Setup Jumper............................................................... 54

4.6.4 LVDS1 Panel Resolution Type Select Jumper (For Intel® Atom™ processor

D525 dual LVDS only).............................................................................................. 55

4.6.5 LVDS2 Panel Resolution Select Jumper.......................................................... 56

4.6.6 LVDS1 Voltage Select setting........................................................................... 57

4.6.7 LVDS2 Voltage Select setting........................................................................... 58

Page vi

Page 7

KINO-PV-D5252/D4252 Mini ITX SBC

4.6.8 Serial Port Setting Jumper............................................................................... 59

4.7 CHASSIS INSTALLATION............................................................................................ 60

4.7.1 Airflow.............................................................................................................. 60

4.7.2 Motherboard Installation................................................................................. 60

4.8 INTERNAL PERIPHERAL DEVICE CONNECTIONS........................................................ 61

4.8.1 AT/ATX Power Connection.............................................................................. 61

4.8.2 Single RS-232 Cable with Slot Bracket............................................................ 62

4.9 SOFTWARE INSTALLATION ........................................................................................ 63

5 BIOS SCREENS........................................................................................................... 65

5.1 INTRODUCTION......................................................................................................... 66

5.1.1 Starting Setup................................................................................................... 66

5.1.2 Using Setup...................................................................................................... 66

5.1.3 Getting Help..................................................................................................... 67

5.1.4 Unable to Reboot After Configuration Changes.............................................. 67

5.1.5 BIOS Menu Bar................................................................................................ 67

5.2 MAIN........................................................................................................................ 68

5.3 ADVANCED............................................................................................................... 69

5.3.1 ACPI Settings................................................................................................... 70

5.3.2 T rusted Computing........................................................................................... 71

5.3.3 CPU Configuration.......................................................................................... 72

5.3.4 IDE Configuration........................................................................................... 73

5.3.5 USB Configuration........................................................................................... 74

5.3.6 Super IO Configuration ................................................................................... 75

5.3.6.1 Serial Port 0 Configuration....................................................................... 76

5.3.6.2 Parallel Port Configuration....................................................................... 79

5.3.7 H/W Monitor.................................................................................................... 81

5.3.8 Secondary Super IO Configuration ................................................................. 83

5.3.8.1 Serial Port 5 Configuration....................................................................... 83

5.3.8.2 Serial Port 6 Configuration....................................................................... 84

5.3.9 Serial Port Console Redirection...................................................................... 85

5.4 CHIPSET ................................................................................................................... 86

5.4.1 Host Bridge Configuration .............................................................................. 87

5.4.1.1 Memory Frequency and Timing................................................................ 88

5.4.1.2 OnChip VGA Configuration..................................................................... 89

Page vii

Page 8

5.4.2 South Bridge Configuration............................................................................. 90

5.4.3 Intel IGD SWSCI OpRegion............................................................................. 91

5.5 BOOT........................................................................................................................ 94

5.6 SECURITY................................................................................................................. 95

5.7 EXIT......................................................................................................................... 96

A REGULATORY COMPLIANCE.............................................................................. 98

B BIOS OPTIONS ........................................................................................................ 100

C TERMINOLOGY ..................................................................................................... 103

D DIGITAL I/O INTERFACE..................................................................................... 107

D.1 INTRODUCTION...................................................................................................... 108

D.2 ASSEMBLY LANGUAGE SAMPLE 1.......................................................................... 109

D.3 ASSEMBLY LANGUAGE SAMPLE 2.......................................................................... 109

KINO-PV-D5252/D4252 Mini ITX SBC

E WATCHDOG TIMER................................................................................................110

F HAZARDOUS MATERIALS DISCLOSURE.........................................................113

F.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS

ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY......................................114

Page viii

Page 9

KINO-PV-D5252/D4252 Mini ITX SBC

List of Figures

Figure 1-1: KINO-PV-D5252/D4252................................................................................................2

Figure 1-2: Connectors ..................................................................................................................3

Figure 1-3: KINO-PV-D5252/D4252 Dimensions (mm) ................................................................4

Figure 1-4: Data Flow Block Diagram...........................................................................................5

Figure 3-1: Connector and Jumper Locations...........................................................................13

Figure 3-2: 12 V Power Connector Location..............................................................................16

Figure 3-3: Battery Connector Location.....................................................................................17

Figure 3-4: CompactFlash® Slot Location.................................................................................18

Figure 3-5: Digital I/O Connector Locations ..............................................................................19

Figure 3-6: CPU Fan Connector Location..................................................................................20

Figure 3-7: Fan Connector Location...........................................................................................21

Figure 3-8: Flash SPI ROM Connector Location .......................................................................22

Figure 3-9: Front Panel Connector Location .............................................................................23

Figure 3-10: Keyboard/Mouse Connector Location..................................................................24

Figure 3-11: Keypad Connector Location..................................................................................25

Figure 3-12: LVDS1 Connector Location ...................................................................................26

Figure 3-13: LVDS1 Backlight Inverter Connector Location....................................................27

Figure 3-14: LVDS2 Connector Location ...................................................................................28

Figure 3-15: LVDS2 Backlight Inverter Connector Location....................................................29

Figure 3-16: Parallel Port Connector Location..........................................................................30

Figure 3-17: PCIe Mini Card Slot Location.................................................................................31

Figure 3-18: SATA Drive Connector Locations.........................................................................33

Figure 3-19: SATA Power Connector Locations .......................................................................34

Figure 3-20: SATA Power Connector Locations .......................................................................35

Figure 3-21: Serial Port (COM5 and COM6) Connector Pinout Locations..............................36

Figure 3-22: Serial Port (COM2) Connector Location...............................................................37

Figure 3-23: SMBus Connector Locations.................................................................................38

Figure 3-24: USB Connector Pinout Locations.........................................................................39

Figure 3-25: KINO-PV-D5252/D4252 External Peripheral Interface Connector ......................40

Figure 3-26: Audio Connector.....................................................................................................40

Page ix

Page 10

Figure 3-27: RJ-45 Ethernet Connector......................................................................................41

Figure 3-28: VGA Connector .......................................................................................................43

Figure 4-1: SO-DIMM Installation................................................................................................49

Figure4-2: SO-DIMM Connector Location..................................................................................49

Figure 4-3: CompactFlash® Card Installation ...........................................................................51

Figure 4-4: AT/ATX Power Select Jumper Location..................................................................53

Figure 4-5: Clear CMOS Jumper .................................................................................................54

Figure 4-6: CompactFlash® Setup Jumper Location ...............................................................55

Figure 4-7: LVDS1 Panel Resolution Jumper Location............................................................56

Figure 4-8: LVDS2 Panel Resolution Jumper Location............................................................57

Figure 4-9: LVDS1 Voltage Select Jumper Location.................................................................58

Figure 4-10: LVDS2 Voltage Select Jumper Location...............................................................59

Figure 4-11: Serial Port Jumper Locations................................................................................60

Figure 4-12: Power Cable to Motherboard Connection............................................................61

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 4-13: Connect Power Cable to Power Supply................................................................62

Figure 4-14: Single RS-232 Cable Installation ...........................................................................63

Figure 4-15: Introduction Screen................................................................................................64

Figure 4-16: Available Drivers.....................................................................................................64

Page x

Page 11

KINO-PV-D5252/D4252 Mini ITX SBC

List of Tables

Table 1-1: Technical Specifications..............................................................................................7

Table 3-1: Peripheral Interface Connectors...............................................................................14

Table 3-2: Rear Panel Connectors..............................................................................................15

Table 3-3: 12 V Power Connector Pinouts .................................................................................16

Table 3-4: Battery Connector Pinouts........................................................................................17

Table 3-5: CompactFlash® Slot Pinouts....................................................................................19

Table 3-6: Digital I/O Connector Pinouts....................................................................................20

Table 3-7: CPU Fan Connector Pinouts......................................................................................21

Table 3-8: Fan Connector Pinouts..............................................................................................22

Table 3-9: SPI Flash Connector Pinouts ....................................................................................22

Table 3-10: Front Panel Connector Pinouts...............................................................................23

Table 3-11: Keyboard/Mouse Connector Pinouts .....................................................................24

Table 3-12: Keypad Connector Pinouts......................................................................................25

Table 3-13: LVDS1 Connector Pinouts.......................................................................................27

Table 3-14: LVDS1 Backlight Inverter Connector Pinouts .......................................................27

Table 3-15: LVDS2 Connector Pinouts.......................................................................................28

Table 3-16: LVDS2 Backlight Inverter Connector Pinouts .......................................................29

Table 3-17: Parallel Port Connector Pinouts .............................................................................30

Table 3-18: PCIe Mini Card Slot Pinouts ....................................................................................32

Table 3-19: SATA Drive Connector Pinouts...............................................................................33

Table 3-20: SATA Power Connector Pinouts.............................................................................34

Table 3-21: SATA Power Connector Pinouts.............................................................................35

Table 3-22: Serial Port Connector Pinouts ................................................................................36

Table 3-23: Serial Port (COM2) Connector Pinouts...................................................................37

Table 3-24: SMBus Connector Pinouts ......................................................................................38

Table 3-25: USB Port Connector Pinouts...................................................................................39

Table 3-26: LAN Pinouts ..............................................................................................................41

Table 3-27: RJ-45 Ethernet Connector LEDs.............................................................................41

Table 3-28: USB Pinouts..............................................................................................................42

Table 3-29: Power Connector Pinouts........................................................................................42

Page xi

Page 12

Table 3-30: Serial Port Pinouts....................................................................................................43

Table 3-31: VGA Connector Pinouts...........................................................................................44

Table 4-1: Jumpers.......................................................................................................................52

Table 4-2: AT/ATX Power Select Jumper Settings....................................................................52

Table 4-3: Clear CMOS Jumper Settings....................................................................................54

Table 4-4: CompactFlash® Setup Jumper Settings..................................................................54

Table 4-5: LVDS1 Panel Resolution Jumper Settings...............................................................56

Table 4-6: LVDS2 Panel Resolution Jumper Settings...............................................................57

Table 4-7: LVDS1 Voltage Select Jumper Settings...................................................................58

Table 4-8: LVDS2 Voltage Select Jumper Settings...................................................................58

Table 4-9: Serial Port Jumper Settings.......................................................................................59

Table 5-1: BIOS Navigation Keys................................................................................................67

KINO-PV-D5252/D4252 Mini ITX SBC

Page xii

Page 13

KINO-PV-D5252/D4252 Mini ITX SBC

BIOS Menus

BIOS Menu 1: Main.......................................................................................................................68

BIOS Menu 2: Advanced..............................................................................................................69

BIOS Menu 3: ACPI Settings .......................................................................................................70

BIOS Menu 4: TPM Configuration...............................................................................................71

BIOS Menu 5: CPU Configuration...............................................................................................72

BIOS Menu 6: IDE Configuration.................................................................................................73

BIOS Menu 7: USB Configuration...............................................................................................74

BIOS Menu 8: Super IO Configuration........................................................................................75

BIOS Menu 9: Serial Port 0 Configuration Menu.......................................................................76

BIOS Menu 10: Parallel Port Configuration Menu.....................................................................79

BIOS Menu 11: Hardware Health Configuration........................................................................81

BIOS Menu 12: Secondary Super IO Configuration..................................................................83

BIOS Menu 13: Serial Port Console Redirection.......................................................................85

BIOS Menu 14: Chipset................................................................................................................86

BIOS Menu 15: Host Bridge Chipset Configuration..................................................................87

BIOS Menu 16: Memory Frequency and Timing Configuration...............................................88

BIOS Menu 17: OnChip VGA Configuration...............................................................................89

BIOS Menu 18: South Bridge Chipset Configuration................................................................90

BIOS Menu 19: Intel IGD SWSCI OpRegion ...............................................................................92

BIOS Menu 20: Boot.....................................................................................................................94

BIOS Menu 21: Security...............................................................................................................95

BIOS Menu 22: Exit.......................................................................................................................96

Page xiii

Page 14

KINO-PV-D5252/D4252 Mini ITX SBC

1 Introduction

Chapter

Page 1

Page 15

1.1 Introduction

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 1-1: KINO-PV-D5252/D4252

The KINO-PV-D5252/D4252 Mini ITX motherboard is an Intel® Atom™ processo r D525 or D425 platform. Up to two 4.0 GB 800 MHz DDR3 SDRAM SO-DIMMs are supported by the KINO-PV-D5252/D4252.

The integrated Intel® ICH8M Chipset supports two GbE LAN ports through two Realtek RTL8111E Ethernet controllers (with ASF 2.0 support on LAN1). The KINO-PV-D5252/D4252 also supports two SATA 3Gb/s drives and provides 5 V SATA power.

The KINO-PV-D5252/D4252 supports an integrated GMA 3150 graphics card with a graphic core speed of 400MHz. Eight USB 2.0 channels, one PCI slot, one PCIe Mini socket, one CompactFlash® connector and one PCIe x1 slot provide flexible expansion options. High Definition Audio (HDA) support ensures HDA devices can be easily implemented on the KINO-PV-D5252/D4252. Serial device connectivity is provided by

Page 2

three external RS-232 ports, two internal RS-232 ports and one internal RS-232/422/485 connector.

Page 16

KINO-PV-D5252/D4252 Mini ITX SBC

1.2 Connectors

The connectors on the KINO-PV-D5252/D4252 are shown in the figure below.

Figure 1-2: Connectors

Page 3

Page 17

1.3 Dimensions

The dimensions of the board are listed below:

KINO-PV-D5252/D4252 Mini ITX SBC

Page 4

Figure 1-3: KINO-PV-D5252/D4252 Dimensions (mm)

Page 18

KINO-PV-D5252/D4252 Mini ITX SBC

1.4 Data Flow

5Figure 1-4 shows the data flow between the two on-board chipsets and other components

installed on the motherboard and described in the following sections of this chapter.

Figure 1-4: Data Flow Block Diagram

Page 5

Page 19

KINO-PV-D5252/D4252 Mini ITX SBC

1.5 Technical Specifications

KINO-PV-D5252/D4252 technical specifications are listed in table below.

Specification KINO-PV-D5252/D4252 Form Factor CPU Options

Express Chipset Graphics Engine Memory

Audio LAN

Super I/O Digital I/O BIOS SMBus

Mini ITX Intel® Atom™ processor D525, 1.8 GHz/1MB L2 cache

Intel® Atom™ processor D425, 1.8 GHz/512KB L2 cache Intel® ICH8M GMA 3150 Two 204-pin SO-DIMM socket s su p port 800 MHz 4.0 GB (max.)

DDR3 SDRAM SO-DIMM Realtek ALC662-GR HD audio codec Two Realtek RTL8111E PCIe GbE controllers with ASF 2.0 support

on LAN1 Fintek F81865 8-bit digital I/O UEFI BIOS label One 4-pin wafer connector

Watchdog Timer Expansion PCIe

PCI I/O Interface Connectors Display Ports

Page 6

Software programmable supports 1~2 55 sec. system reset

One PCIe Mini slot (PCIe + USB + SATA signal) One PCIe x1 slot

One PCI slot

Analog CRT, resolution support up to 2048x1536 CRT hot plug supported 18-bit single-channel LVDS, resolution support up to WXGA

1366x768 or XGA 1024x768 24-bit dual-channel LVDS by Novatek NT68660BUFG, resolution

support up to 1920x1080

Page 20

KINO-PV-D5252/D4252 Mini ITX SBC

Specification KINO-PV-D5252/D4252 Ethernet

Serial Ports

USB 2.0/1.1 Ports

Parallel Ports TPM Storage Serial ATA

Environmental and Power Specifications

Two RJ-45 G bE ports by Realtek RTL8111E with ASF 2.0 support on LAN1

Three RS-232 via Rear I/O Two RS-232 via four 10-pin headers One RS-232/422/485 via 14–pin header

Four external USB ports Four internal USB ports via 8-pin headers

One LPT connector via 26-pin header INFINEON SLB9635TT1.2 (Optional)

Two SATA 3.0 Gb/s connectors One 5 V SATA power connector One 5 V/12 V SATA power connector

Power Supply

Power Connector

Power Consumption Operating Temperature

Humidity Physical Specifications Dimensions Weight GW/NW

Table 1-1: Technical Specifications

12 V only ATX and AT power supported

One external DIN 4-pin DC jack One internal 4-pin power connector

12 V @ 1.95A (Intel® Atom™ D525 1.8GHz with DDR3 1GB*2)

-20°C ~ 60°C with free air, -20°C ~ 70°C with force air for D525 processor

-20°C ~ 65°C with free air, -20°C ~ 70°C with force air for D425 processor

5% ~ 95% (non-condensing)

170 mm x 170 mm 800 g / 340 g

Page 7

Page 21

KINO-PV-D5252/D4252 Mini ITX SBC

Chapter

2 Unpacking

Page 8

Page 22

KINO-PV-D5252/D4252 Mini ITX SBC

2.1 Anti-static Precautions

WARNING!

Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user.

Make sure to adhere to the following guidelines:

 Wear an anti-static wristband: Wearing an anti-static wristband can prevent

electrostatic discharge.

 Self-grounding: Touch a g rounded cond uctor every few minutes to discharge

any excess static buildup.

 Use an anti-static pad: When configuring any circuit board, place it on an

anti-static mat.

 Only handle the edges of the PCB: Don't touch the surface of the

motherboard. Hold the motherboard by the edges when handling.

2.2 Unpacking Precautions

When the KINO-PV-D5252/D4252 is unpacked, please do the following:

 Follow the anti-static guidelines above.  Make sure the packing box is facing upwards when opening.  Make sure all the packing list items are present.

Page 9

Page 23

2.3 Packing List

NOTE:

If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the KINO-PV-D5252/D4252 was purchased from or contact an IEI sales

KINO-PV-D5252/D4252 Mini ITX SBC

representative directly by sending an email to

The KINO-PV-D5252/D4252 is shipped with the following components:

Quantity Item and Part Number Image

1 KINO-PV-D5252-L2-R11/KINO-PV-D4252-R11

single board computer

1 SATA and 5 V power cable

(P/N: 32801-000100-300-RS)

1 RS-232 cable with bracket

(P/N: 19800-000300-100-RS)

1 I/O shielding

(P/N: 45014-0024C0-01-RS)

32sales@ieiworld.com.

Page 10

1 Mini jumper pack (2.0mm)

(P/N: 33100-000033-RS)

1 Utility CD

1 One Key Recovery CD

Page 24

KINO-PV-D5252/D4252 Mini ITX SBC

1 Quick Installation Guide

2.3.1 Optional Items

The following are optional components which may be separately purchased:

Item and Part Number Image

LPT cable (P/N: 32200-015100-RS)

KB/MS PS/2 Y-cable (P/N: 32000-0023800-RS)

4-pin (2x2) to 4-pin (1x4) DC power cable with te rminal block (P/N: 32100-192900-RS)

Dual RS-232/422/485 cable with bracket (P/N: 19800-004300-100-RS)

Dual-port USB cable with bracket (P/N: 19800-003100-300-RS)

CPU fan (P/N: 19FFD124010HB2A7-000001-RS)

Heat sink (30 mm higher) (P/N: 34000-000510-RS)

PCIe x1 riser card (P/N: PCIER-K101L-R10)

Page 11

Page 25

KINO-PV-D5252/D4252 Mini ITX SBC

Chapter

3 Connectors

Page 12

Page 26

KINO-PV-D5252/D4252 Mini ITX SBC

3.1 Peripheral Interface Connectors

This chapter details all the jumpers and connectors.

3.1.1 KINO-PV -D5252/D4252 Layout

The figures below show all the connectors and jumpers.

Figure 3-1: Connector and Jumper Locations

Page 13

Page 27

3.1.2 Peripheral Interface Connectors

The table below lists all the connectors on the board.

Connector Type Label

12 V Power connector 4-pin connector PWR2 Battery connector 2-pin wafer BAT1 CompactFlash® slot 50-pin header CF1 Digital I/O connector 10-pin header DIO1 Fan connector (CPU) 4-pin wafer CPU_FAN1 Fan connector 3-pin header J4 Flash SPI ROM 8-pin header SPI1 Front panel connector 8-pin header F_PANEL1

KINO-PV-D5252/D4252 Mini ITX SBC

Keyboard and mouse connector 6-pin wafer KB_MS1 Keypad connector 9-pin wafer KEY1 L V DS1 conne ctor 30-pin crimp L V DS1 LVDS1 Backlight Inverter connector 5-pin wafer INV1 L V DS2 conne ctor 20-pin crimp L V DS2 LVDS2 Backlight Inverter connector 5-pin wafer INV2 Parallel port connector 26-pin header LPT1 PCIe Mini card slot PCIe Mini card slot CN2 Serial ATA (SATA) drive connector 7-pin SATA SATA1, SATA2 SATA power connector 2-pin wafer, 4-pin wafer SATA_PWR1 ,

SATA_PWR2 Serial port connector (RS-232) 10-pin header COM5, COM6 Serial port connector (RS-232) 14-pin header COM2 SMBus connector 4-pin wafer CN4

Page 14

USB connector 8-pin header USB1, USB2

Table 3-1: Peripheral Interface Connectors

Page 28

KINO-PV-D5252/D4252 Mini ITX SBC

3.1.3 External Interface Panel Connectors

The table below lists the connectors on the external I/O panel.

Connector Type Label

Audio connector Line-out, Mic JAUDIO1 Ethernet and USB connector RJ-45 USBLAN1, USBLAN2 Power connector 5-pin connector PWR1 Serial port connector 9-pin male COM1, COM3, COM4 VGA port connector 15-pin connector VGACOM1

Table 3-2: Rear Panel Connectors

3.2 Internal Peripheral Connectors

The section describes all of the connectors on the KINO-PV-D5252/D4252.

3.2.1 12V Power Connector

CN Label: PWR2 CN Type: CN Location: CN Pinouts:

The connector supports the 12V power supply.

4-pin Molex power connector (1x4), p=4.2mm

Figure 3-2

See

Table 3-3

See

Page 15

Page 29

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 3-2: 12 V Power Connector Location

Pin Description Pin Description

1 GND 2 GND 3 +12V 4 +12V

Table 3-3: 12 V Power Connector Pinouts

3.2.2 Battery Connector

CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.

Dispose of used batteries according to instructions and local regulations.

CN Label: BAT1

Page 16

CN Type: CN Location: CN Pinouts:

This is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off.

2-pin wafer, p=1.25mm

Figure 3-3

See

Table 3-4

See

Page 30

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 3-3: Battery Connector Location

Pin Description

1 VCC_BAT 3 GND

Table 3-4: Battery Connector Pinouts

3.2.3 CompactFlash® Slot

CN Label: CF1 CN Type: CN Location: CN Pinouts:

A CompactFlash® Type I/II card can be used in this slot.

CompactFlash® card slot See See

Figure 3-4 Table 3-5

Page 17

Page 31

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 3-4: CompactFlash® Slot Location

Pin Description Pin Description

1 GND 26 CD1# 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5 D6 30 D14 6 D7 31 D15 7 CE# 32 CE2# 8 A10 33 VS1# 9 OE# 34 IOR# 10 A9 35 IOW# 11 A8 36 WE# 12 A7 37 IRQ 13 VCC 38 VCC

Page 18

14 A6 39 CSEL# 15 A5 40 VS2# 16 A4 41 RESET#

Page 32

KINO-PV-D5252/D4252 Mini ITX SBC

Pin Description Pin Description

17 A3 42 WAIT# 18 A2 43 INPACK# 19 A1 44 REG# 20 A0 45 BVD2 21 D0 46 BVD1 22 D1 47 D8 23 D2 48 D9 24 IOCS16# 49 D10 25 CD2# 50 GND2

Table 3-5: CompactFlash® Slot Pinouts

3.2.4 Digital I/O Connector

CN Label: DIO1 CN Type: CN Location: CN Pinouts:

10-pin header, p=2 mm

Figure 3-5

See

Table 3-6

See

The digital I/O connector provides programmable input and output for external devices. The digital I/O provides 4-bit output and 4-bit input.

Figure 3-5: Digital I/O Connector Locations

Page 19

Page 33

Pin Description Pin Description

1 Ground 2 VCC5 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input 3 8 Input 2 9 Input 1 10 Input 0

Table 3-6: Digital I/O Connector Pinouts

3.2.5 Fan Connector (CPU)

CN Label: CPU_FAN1

KINO-PV-D5252/D4252 Mini ITX SBC

CN Type: CN Location: CN Pinouts:

4-pin wafer, p=2.54 mm

Figure 3-6

See

Table 3-7

See

The fan connector attaches to a CPU cooling fan.

Page 20

Figure 3-6: CPU Fan Connector Location

Page 34

KINO-PV-D5252/D4252 Mini ITX SBC

Pin Description

1 GND 2 VCC12 3 FANIN1 4 FANOUT1

Table 3-7: CPU Fan Connector Pinouts

3.2.6 Fan Connector

CN Label: J4 CN Type: CN Location: CN Pinouts:

3-pin header, p=2.54 mm

Figure 3-7

See

Table 3-8

See

The fan connector attaches to a cooling fan.

Figure 3-7: Fan Connector Location

Pin Description

1 FANIO1

Page 21

Page 35

Pin Description

2 +12V (PWM) 3 GND

Table 3-8: Fan Connector Pinouts

3.2.7 Flash SPI ROM

CN Label: SPI1

KINO-PV-D5252/D4252 Mini ITX SBC

CN Type: CN Location: CN Pinouts:

8-pin header, p=2.54 mm

Figure 3-8

See

Table 3-9

See

The connector provides a Flash SPI BIOS update.

Figure 3-8: Flash SPI ROM Connector Location

Pin Description Pin Description

Page 22

1 SPI_VCC 2 GND 3 SPI_CS 4 SPI_CLK 5 SPI_SO 6 SPI_SI 7 NC 8 NC

Table 3-9: SPI Flash Connector Pinouts

Page 36

KINO-PV-D5252/D4252 Mini ITX SBC

3.2.8 Front Panel Connector

CN Label: F_PANEL1 CN Type: CN Location: CN Pinouts:

8-pin header, p=2.54 mm

Figure 3-9

See

Table 3-10

See

The front panel connector connects to external switches and indicators to monitor and controls the motherboard. These indicators and switches include:

 Power button  Reset  Power LED  HDD LED

Figure 3-9: Front Panel Connector Location

FUNCTION PIN DESCRIPTION FUNCTION PIN DESCRIPTION

1 PWRBTSW- 2 PWR_LED+ Power Button 3 GND 5 VCC 6 PM_RESET HDD LED 7 -HDLED

Table 3-10: Front Panel Connector Pinouts

Power LED

4 GND

Reset

8 GND

Page 23

Page 37

3.2.9 Keyboard/Mouse Connector

CN Label: KB_MS1

KINO-PV-D5252/D4252 Mini ITX SBC

CN Type: CN Location: CN Pinouts:

6-pin wafer, p=2 mm

Figure 3-10

See

Table 3-11

See

The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a PS/2 keyboard and mouse.

Figure 3-10: Keyboard/Mouse Connector Location

Pin Description

1 VCC 2 Mouse Data 3 Mouse Clock 4 Keyboard Data 5 Keyboard Clock 6 GND

Table 3-11: Keyboard/Mouse Connector Pinouts

3.2.10 Keypad Connector

CN Label: KEY1

9-pin header, p=1.25 mm

Page 24

CN Type:

Page 38

KINO-PV-D5252/D4252 Mini ITX SBC

See

CN Location: CN Pinouts:

Figure 3-11 Table 3-12

See

The keypad connector can be used to install a numeric keypad.

Figure 3-11: Keypad Connector Location

Pin Description

1 Red LED 2 NC 3 Green LED 4 Menu/Enter 5 Up 6 Down 7 Auto/Exit 8 Power 9 Ground

Table 3-12: Keypad Connector Pinouts

3.2.11 LVDS1 Connector (For Intel® Atom™ processor D525 dual LVDS only)

CN Label: LVDS1 CN Type:

30-pin crimp, p=1.25 mm

Page 25

Page 39

See

CN Location: CN Pinouts:

Figure 3-12 Table 3-13

See

KINO-PV-D5252/D4252 Mini ITX SBC

The LVDS connector is for an LCD panel connected to the board.

Figure 3-12: LVDS1 Connector Location

Pin Description Pin Description

1 GND 2 GND 3 LVDS_A_TX0-P 4 LVDS_A _TX0-N 5 LVDS_A_TX1-P 6 LVDS_A _TX1-N 7 LVDS_A_TX2-P 8 LVDS_A _TX2-N 9 LVDS_A_TXCLK-P 10 LVDS_A _TXCLK-N 11 LVDS_A_TX3-P 12 LVDS_A _TX3-N 13 GND 14 GND 15 LVDS_B _TX0-P 16 LVDS_B _TX0-N 17 LVDS_B _TX1-P 18 LVDS_B _TX1-N 19 LVDS_B _TX2-P 20 LVDS_B _TX2-N 21 LVDS_B _TXCLK-P 22 LVDS_B _TXCLK-N 23 LVDS_B _TX3-P 24 LVDS_B _TX3-N

Page 26

25 GND 26 GND

Page 40

KINO-PV-D5252/D4252 Mini ITX SBC

Pin Description Pin Description

27 +LCD Vcc 28 +LCD Vcc 29 +LCD Vcc 30 +LCD Vcc

Table 3-13: LVDS1 Connector Pinouts

3.2.12 LVDS1 Backlight Inverter Connector

CN Label: INV1 CN Type: CN Location: CN Pinouts:

5-pin wafer, p=2 mm

Figure 3-13

See

Table 3-14

See

The backlight inverter connector provides power to an LCD panel.

Figure 3-13: LVDS1 Backlight Inverter Connector Location

Pin Description

1 LCD_BKLTCTL 2 GROUND 3 +12V 4 GROUND 5 BACKLIGHT ENABLE

Table 3-14: LVDS1 Backlight Inverter Connector Pinouts

Page 27

Page 41

3.2.13 LVDS2 Connector

CN Label: LVDS2

KINO-PV-D5252/D4252 Mini ITX SBC

CN Type: CN Location: CN Pinouts:

20-pin crimp, p=1.25 mm

Figure 3-12

See

Table 3-13

See

The LVDS connector is for an LCD panel connected to the board.

Figure 3-14: LVDS2 Connector Location

Pin Description Pin Description

Page 28

1 GND1 2 GND2 3 A_Y0 4 A_Y0# 5 A_Y1 6 A_Y1# 7 A_Y2 8 A_Y2# 9 A_CK 10 A_CK# 11 NC 12 NC 13 GND3 14 GND4 15 NC 16 NC 17 VCC_LCD 18 VCC_LCD 19 VCC_LCD 20 VCC_LCD

Table 3-15: LVDS2 Connector Pinouts

Page 42

KINO-PV-D5252/D4252 Mini ITX SBC

3.2.14 LVDS2 Backlight Inverter Connector

CN Label: INV2 CN Type: CN Location: CN Pinouts:

The backlight inverter connector provides power to an LCD panel.

Figure 3-15: LVDS2 Backlight Inverter Connector Location

5-pin wafer, p=2 mm

Figure 3-13

See

Table 3-14

See

Pin Description

1 LCD_BKLTCTL 2 GROUND 3 +12V 4 GROUND 5 BACKLIGHT ENABLE

Table 3-16: LVDS2 Backlight Inverter Connector Pinouts

3.2.15 Parallel Port Connector

CN Label: LPT1 CN Type: CN Location:

26-pin box header, p=2.54 mm

Figure 3-16

See

Page 29

Page 43

See

CN Pinouts:

Table 3-17

KINO-PV-D5252/D4252 Mini ITX SBC

The parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer.

Figure 3-16: Parallel Port Connector Location

Pin Description Pin Description

1 STROBE# 2 AUTO FORM FEED # 3 DATA0 4 ERROR# 5 DATA1 6 INITIALIZE# 7 DATA2 8 PRINTER SELECT LN# 9 11 13 15 17 19 21 23 25

DATA3 10 GND DATA4 12 GND DATA5 14 GND DATA6 16 GND DATA7 18 GND ACKNOWLEDGE# 20 GND BUSY 22 GND PAPER EMPTY 24 GND PRINTER SELECT 26 NC

Page 30

Table 3-17: Parallel Port Connector Pinouts

Page 44

KINO-PV-D5252/D4252 Mini ITX SBC

3.2.16 PCIe Mini Card Slot

CN Label: CN2 CN Type: CN Location: CN Pinouts:

PCIe Mini card slot

5Figure 3-17

See

Table 3-18

See

The PCIe Mini card slot is for installing PCIe Mini expansion cards.

Figure 3-17: PCIe Mini Card Slot Location

Pin Description Pin Description

1 PCIE_WAKE# 2 VCC3 3 N/C 4 GND 5 N/C 6 1.5 V 7 CLKREQ# 8 LFRAME# 9 GND 10 LAD3 11 CLK- 12 LAD2 13 CLK+ 14 LAD1 15 GND 16 LAD0

Page 31

Page 45

Pin Description Pin Description

17 PCIRST# 18 GND 19 LPC 20 VCC3 21 GND 22 PCIRST# 23 PERN2 24 3VDual 25 PERP2 26 GND 27 GND 28 1.5 V 29 GND 30 SMBCLK 31 PETN2 32 SMBDATA 33 PETP2 34 GND 35 GND 36 USBD37 GND 38 USBD+ 39 SATARXP 40 GND 41 SATARXN 42 N/C

KINO-PV-D5252/D4252 Mini ITX SBC

43 N/C 44 RF_LINK# 45 SATATXN 46 BLUELED# 47 SATATXP 48 1.5 V 49 GND 50 GND 51 N/C 52 VCC3

Table 3-18: PCIe Mini Card Slot Pinouts

3.2.17 SATA Drive Connectors

CN Label: SATA1, SATA2 CN Type: CN Location: CN Pinouts:

The two SATA 3Gb/s drive connectors are each connected to a SATA 3Gb/s drive. The SATA 3Gb/s drives transfer data at speeds as high as 3.0 Gb/s.

7-pin SATA drive connectors

5Figure 3-18

See

5Table 3-19

See

Page 32

Page 46

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 3-18: SATA Drive Connector Locations

Pin Description

1 GND 2 TX+ 3 TX4 GND 5 RX6 RX+ 7 GND

Table 3-19: SATA Drive Connector Pinouts

3.2.18 SATA Power Connectors

CN Label: SATA_PWR1 CN Type: CN Location: CN Pinouts:

2-pin wafer, p=2.54 mm

Figure 3-19

See

Table 3-20

See

The SATA Power Connector provides power output to the SATA connectors.

Page 33

Page 47

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 3-19: SATA Power Connector Locations

Pin Description

1 +5V 2 GND

Table 3-20: SATA Power Connector Pinouts

CN Label: SATA_PWR2 CN Type: CN Location: CN Pinouts:

The SATA Power Connector provides power output to the SATA connectors.

4-pin wafer, p=2.5 mm

Figure 3-20

See

Table 3-21

See

Page 34

Page 48

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 3-20: SATA Power Connector Locations

Pin Description

1 12V 2 GND 3 GND 4 5V

Table 3-21: SATA Power Connector Pinouts

3.2.19 Serial Port Connectors (RS-232)

CN Label: COM5, COM6 CN Type: CN Location: CN Pinouts:

This connector provides RS-232 communications.

10-pin header, p=2 mm

5Figure 3-21

See

5Table 3-22

See

Page 35

Page 49

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 3-21: Serial Port (COM5 and COM6) Connector Pinout Locations

Pin Description Pin Description

1 Data Carrier Direct (DCD) 2 Data Set Ready (DSR) 3 Receive Data (RXD) 4 Request To Send (RTS) 5 Transmit Data (TXD) 6 Clear To Send (CTS) 7 Data Terminal Ready (DTR) 8 Ring Indicator (RI) 9 Ground (GND) 10 Ground (GND)

Table 3-22: Serial Port Connector Pinouts

3.2.20 Serial Port Connector (RS-232)

CN Label: COM2 CN Type: CN Location: CN Pinouts:

Used for RS-232/422/485 communications.

14-pin header, p=2 mm

Figure 3-22

See

Table 3-23

See

Page 36

Page 50

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 3-22: Serial Port (COM2) Connector Location

Pin Description Pin Description

1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 GND 10 N/C 11 TXD485+ 12 TXD485# 13 RXD485+ 14 RXD485#

Table 3-23: Serial Port (COM2) Connector Pinouts

3.2.21 SMBus Connector

CN Label: CN4 CN Type: CN Location: CN Pinouts:

4-pin wafer, p=1.25 mm

Figure 3-23

See

Table 3-24

See

The SMBus Connector provides a connection to a SMBus (System Management Bus) device.

Page 37

Page 51

Figure 3-23: SMBus Connector Locations

KINO-PV-D5252/D4252 Mini ITX SBC

Pin Description

1 Ground 2 SMB_DATA 3 SMB_CLK 4 +5V

Table 3-24: SMBus Connector Pinouts

3.2.22 USB Connectors

CN Label: USB1, USB2 CN Type: CN Location: CN Pinouts:

The USB connectors connect to USB devices. Each pin header provides two USB ports.

8-pin header, p=2.54 mm

Figure 3-24

See

Table 3-25

See

Page 38

Page 52

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 3-24: USB Connector Pinout Locations

Pin Description Pin Description

1 VCC 2 GND 3 DATA- 4 DATA+ 5 DATA+ 6 DATA7 GND 8 VCC

Table 3-25: USB Port Connector Pinouts

3.3 External Peripheral Interface Connector Panel

5Figure 3-25 shows the KINO-PV-D5252/D4252 external peripheral interface connector

(EPIC) panel. The KINO-PV-D5252/D4252 EPIC panel consists of the following:

 4 x USB connectors  2 x Ethernet connector  1 x Line-out  1x Microphone  1 x VGA  3 x Serial port (RS-232)  1 x 12 V DC input

Page 39

Page 53

Figure 3-25: KINO-PV-D5252/D4252 External Peripheral Interface Connector

3.3.1 Audio Connector

CN Label: JAUDIO1

KINO-PV-D5252/D4252 Mini ITX SBC

CN Type: CN Location:

Line-out, Mic

5Figure 3-25

See

The audio jacks connect to external audio devices.

 Line-out port (Lime): Connects to a headphone or a speaker. With

multi-channel configurations, this port can also connect to front speakers.

 Microphone (Pink): Connects a microphone.

Figure 3-26: Audio Connector

3.3.2 Ethernet and USB Connector

Page 40

CN Label: USBLAN1, USBLAN2 CN Type: CN Location: CN Pinouts:

RJ-45 port, USB port

5Figure 3-25

See

5Table 3-26, Table 3-28

See

Page 54

KINO-PV-D5252/D4252 Mini ITX SBC

The KINO-PV-D5252/D4252 is equipped with two built-in RJ-45 Ethernet controllers. The controllers can connect to the LAN through the RJ-45 LAN connectors.

Pin Description Pin Description

P1 3.3V supply P2 LAN signal differential pair (0+) P3 LAN signal differential pair (0-) P4 LAN signal differential pair (1+) P5 LAN signal differential pair (1-) P6 LAN signal differential pair (2+) P7 LAN signal differential pair (2-) P8 LAN signal differential pair (3+) P9 LAN signal differential pair (3-) P10 GND P11 Right LED signal(-) P12 Right LED signal(+) P13 Left LED signal(-) P14 Left LED signal(+) 9 Chassis GND 10 Chassis GND 11 Chassis GND 12 Chassis GND 13 Chassis GND 14 Chassis GND 15 Chassis GND 16 Chassis GND

Table 3-26: LAN Pinouts

The RJ-45 Ethernet connectors have two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the speed. See

5Table 3-27.

Speed LED Activity/Link LED STATUS

Off 10 Mbps connection Off No link Green 100 Mbps connection Yellow Linked Orange Gbps conne ction Blinking TX/RX activity 1

DESCRIPTION STATUS DESCRIPTION

Table 3-27: RJ-45 Ethernet Connector LEDs

Figure 3-27: RJ-45 Ethernet Connector

The USB connector can be connected to a USB device.

Page 41

Page 55

Pin Description

1 VCC 2 DATA03 DATA0+ 4 GND 5 VCC 6 DATA17 DATA1+ 8 GND

Table 3-28: USB Pinouts

3.3.3 Power Connector

CN Label: PWR1

KINO-PV-D5252/D4252 Mini ITX SBC

CN Type: CN Location: CN Pinouts:

5-pin connector See See

The connector supports the 12V power adapter.

Pin Description

1 12V 2 GND 3 12V 4 GND 5 GND

Table 3-29: Power Connector Pinouts

3.3.4 Serial Port Connector

CN Label: COM1, COM3, COM4

5Figure 3-25 5Table 3-29

Page 42

CN Type: CN Location: CN Pinouts:

9-pin male

Figure 3-25

Table 3-30

See

Page 56

KINO-PV-D5252/D4252 Mini ITX SBC

The serial port connects to a RS-232 serial communications device.

Pin Description

1 DATA CARRIER DETECT (DCD) 2 DATA SET READY (DSR) 3 RECEIVE DATA (RXD) 4 REQUEST TO SEND (RTS) 5 TRANSMIT DATA (TXD) 6 CLEAR TO SEND (CTS) 7 DATA TERMINAL READY (DTR) 8 RING INDICATOR (RI) 9 GND (GND) 10 N/C

Table 3-30: Serial Port Pinouts

3.3.5 VGA Port Connector

CN Label: VGACOM1 CN Type: CN Location: CN Pinouts:

15-pin Female VGA connector See See

The VGA port connects to a monitor that accepts a standard VGA input.

Figure 3-28: VGA Connector

Pin Description Pin Description

Figure 3-25 Table 3-31

1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND

Page 43

Page 57

Pin Description Pin Description

7 GND 8 GND 9 CRT_VCC 10 Display_GND 11 NC 12 DDCDAT 13 HSYNC 14 VSYNC 15 DDCCLK

KINO-PV-D5252/D4252 Mini ITX SBC

Table 3-31: VGA Connector Pinouts

Page 44

Page 58

KINO-PV-D5252/D4252 Mini ITX SBC

Chapter

4 Installation

Page 45

Page 59

4.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the KINO-PV-D5252/D4252 may result in permanent damage to the KINO-PV-D5252/D4252 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO-PV-D5252/D4252. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the KINO-PV-D5252/D4252 or any other electrical component is handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple ant i-static wristband can

KINO-PV-D5252/D4252 Mini ITX SBC

help to prevent ESD from damaging the board.

 Self-grounding: Before handling the board, touch any grounded conducting

material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground.

 Use an anti-static pad: When configuring the KINO-PV-D5252/D4252, place

it on an anti-static pad. This reduces the possibility of ESD damaging the KINO-PV-D5252/D4252.

 Only handle the edges of the PCB: When handling the PCB, hold the PCB

by the edges.

Page 46

Page 60

KINO-PV-D5252/D4252 Mini ITX SBC

4.2 Installation Considerations

NOTE:

The following installation notices and installation considerations should be read and understood before the KINO-PV-D5252/D4252 is installed. All installation notices pertaining to the installation of the KINO-PV-D5252/D4252 should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the KINO-PV-D5252/D4252 and injury to the person installing the motherboard.

4.2.1 Installation Notices

WARNING:

The installation instructions described in this manual should be carefully followed in order to prevent damage to the KINO-PV-D5252/D4252, KINO-PV-D5252/D4252 components and injury to the user.

Before and during the installation please DO the following:

 Read the user manual:

o The user manual provides a complete description of the

KINO-PV-D5252/D4252 installation instructions and configuration options.

 Wear an electrostatic discharge cuff (ESD):

o Electronic components are easily damaged by ESD. Wearing an ESD cuff

removes ESD from the body and helps prevent ESD damage.

 Place the KINO-PV-D5252/D4252 on an anti-static pad:

o When installing or configuring the motherboard, place it on an anti-static

pad. This helps to prevent potential ESD damage.

Page 47

Page 61

 Turn all power to the KINO-PV-D5252/D4252 off:

o When working with the KINO-PV-D5252/D4252, make sure that it is

Before and during the installation of the KINO-PV-D5252/D4252 DO NOT:

 Remove any of the stickers on the PCB board. These stickers are required for

warranty validation.

 Use the product before verifying all the cables and power connectors are

properly connected.

 Allow screws to come in contact with the PCB circuit, connector pins, or its

components.

4.3 Unpacking

KINO-PV-D5252/D4252 Mini ITX SBC

disconnected from all power supplies and that no electricity is being fed into the system.

When the KINO-PV-D5252/D4252 is unpacked, please check all the unpacking list items listed in Chapter 3 are indeed present. If any of the unpacking list items are not available please contact the KINO-PV-D5252/D4252 vendor reseller/vendor where the KINO-PV-D5252/D4252 was purchased or contact an IEI sales representative.

4.4 SO-DIMM Installation

SO-DIMM is a critical component of the KINO-PV-D5252/D4252. If it is not installed the KINO-PV-D5252/D4252 cannot run.

Page 48

Page 62

KINO-PV-D5252/D4252 Mini ITX SBC

4.4.1 SO-DIMM Installation

To install a SO-DIMM, please follow the steps below and refer to Figure 4-1.

Figure 4-1: SO-DIMM Installation

Step 1: Locate the SO-DIMM socket on the board (See the figure below). Place the

board on an anti-static mat.

Figure

ٛ 4-2: SO-DIMM Connector Location

Page 49

Page 63

Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the

notch on the memory socket.

KINO-PV-D5252/D4252 Mini ITX SBC

Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See

Step 4: Seat the SO-DIMM. Gently push downwards and the arms clip into place. (See

Figure 4-1)

4.5 CompactFlash® Installation

NOTE:

Both CompactFlash® Type I and Type II cards are supported.

To install the CompactFlash® card, please follow the steps below.

Step 1: Locate the CF card socket. Locate the CompactFlash® slot.

Step 2: Align the CF card. Align the CompactFlash® card. The label side should be

facing away from the board. The grooves on the CompactFlash® slot ensure

Figure 4-1)

Page 50

that the card cannot be inserted the wrong way.

Step 3: Insert the CF card. Push until the CompactFlash® card is firmly seated in the

slot. See

Figure 4-3.

Page 64

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 4-3: CompactFlash® Card Installation

4.6 Jumper Settings

NOTE:

A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper.

Before the KINO-PV-D5252/D4252 is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the KINO-PV-D5252/D4252 are listed in

5Table 4-1.

Page 51

Page 65

Description Type Label

AT/ATX Power setting 3-pin wafer ATXCTL 1 Clear CMOS 3-pin header J_CMOS1 CompactFlash® setting 2-pin header JCF1 LVDS1 Panel Resolution Select setting 8-pin header JP4 LVDS2 Panel Resolution Select setting 6-pin header J_LCD_TYPE1 LVDS1 Voltage Select setting 6-pin header J_VLVDS1 LVDS2 Voltage Select setting 2-pin header J_VLVDS2 Serial port setting 8-pin header JP3

Table 4-1: Jumpers

KINO-PV-D5252/D4252 Mini ITX SBC

4.6.1 AT/ATX Power Select Jumper Settings

Jumper Label: ATXCTL1 Jumper Type: Jumper Settings: Jumper Location:

The AT/ATX Power Select jumper specifies the systems power mode as AT or ATX. AT/ATX Power Select jumper settings are shown in

AT Power Select Description

Short 1 - 2 Use ATX power Short 2 – 3 Use AT power Default

Table 4-2: AT/ATX Power Select Jumper Settings

The location of the AT/ATX Power Select jumper is shown in Figure 4-4 below.

3-pin header, p=2 mm

Table 4-2

See

Figure 4-4

See

Table 4-2.

Page 52

Page 66

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 4-4: AT/ATX Power Select Jumper Location

4.6.2 Clear CMOS Jumper

Jumper Label: J_CMOS1 Jumper Type: Jumper Settings: Jumper Location:

3-pin header, p=2 mm

5Table 4-3

See

5Figure 4-5

See

If the KINO-PV-D5252/D4252 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.

If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the following:

 Enter the correct CMOS setting  Load Optimal Defaults  Load Failsafe Defaults.

After having done one of the above, save the changes and exit the CMOS Setup menu.

The clear CMOS jumper settings are shown in

5Table 4-3.

Page 53

Page 67

Clear CMOS Descr ipti on Short 1 - 2 Keep CMOS Setup Default Short 2 - 3 Clear CMOS Setup

KINO-PV-D5252/D4252 Mini ITX SBC

Table 4-3: Clear CMOS Jumper Settings

The location of the clear CMOS jumper is shown in 5Figure 4-5 below.

Figure 4-5: Clear CMOS Jumper

4.6.3 CompactFlash® Card Setup Jumper

Jumper Label: JCF1 Jumper Type: Jumper Settings: Jumper Location:

The CompactFlash® slot is connected through an IDE connection. This jumper sets the CompactFlash® card as the master or slave IDE device.

Setting Description

Open Slave Closed Master

2-pin header, p=2 mm

Table 4-4

See

Figure 4-6

See

Page 54

Table 4-4: CompactFlash® Setup Jumper Settings

Page 68

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 4-6: CompactFlash® Setup Jumper Location

4.6.4 LVDS1 Panel Resolution Type Select Jumper (For Intel® Atom™ processor D525 dual LVDS only)

Jumper Label: JP4 Jumper Type: Jumper Settings: Jumper Location:

The LVDS1 Panel Resolution jumper configures the resolution of the LVDS output. The LVDS1 Panel Resolution jumper settings are shown below.

Setting Description

Open 1024 x 768 (24-bit) Short 1-2 800 x 600 (18-bit) Short 3-4 1024 x 768 (18-bit)

8-pin header, p=2 mm

Table 4-6

See

Figure 4-8

See

Short 1-2 and 3-4 (Default) 1280 x 1024 (24-bit) Short 5-6 1366 x 768 (24-bit) Short 1-2 and 5-6 1920 x 1080 (24-bit)

Page 55

Page 69

Setting Description

Short 7-8 Brightness inverse

KINO-PV-D5252/D4252 Mini ITX SBC

Table 4-5: LVDS1 Panel Resolution Jumper Settings

Figure 4-7: LVDS1 Panel Resolution Jumper Location

4.6.5 LVDS2 Panel Resolution Select Jumper

Jumper Label: J_LCD_TYPE1 Jumper Type: Jumper Settings: Jumper Location:

The LVDS2 Panel Resolution jumper configures the resolution of the LVDS output. The LVDS2 Panel Resolution jumper settings are shown below.

Setting Description

Open 640 x 480 (18 bit) Short 1-2 800 x 400 (18 bit) Short 3-4 (Default) 800 x 600 (18 bit)

6-pin header, p=2 mm

Table 4-6

See

Figure 4-8

See

Page 56

Page 70

KINO-PV-D5252/D4252 Mini ITX SBC

Setting Description

Short 1-2 and 3-4 1024 x 768 (18 bit) Short 5-6 1280 x 1024 (18 bit) Short 1-2 and 5-6 1366 x 768 (18 bit) Short 3-4 and 5-6 1280 x 800 (18 bit) Short 1-2, 3-4 and 5-6 1280 x 600 (18 bit)

Table 4-6: LVDS2 Panel Resolution Jumper Settings

Figure 4-8: LVDS2 Panel Resolution Jumper Location

4.6.6 LVDS1 Voltage Select setting

Jumper Label: J_VLVDS1 Jumper Type: Jumper Settings: Jumper Location:

6-pin header, p=2 mm

Table 4-8

See

Figure 4-10

See

The voltage selection jumper sets the voltage of the power supplied to the LCD panel.

Setting Description

Short 1-2 12 V

Page 57

Page 71

Setting Description

Short 3-4 5 V (Default) Short 5-6 3.3 V

KINO-PV-D5252/D4252 Mini ITX SBC

Table 4-7: LVDS1 Voltage Select Jumper Settings

Figure 4-9: LVDS1 Voltage Select Jumper Location

4.6.7 LVDS2 Voltage Select setting

Jumper Label: J_VLVDS2 Jumper Type: Jumper Settings: Jumper Location:

The voltage selection jumper sets the voltage of the power supplied to the LCD panel.

Setting Description

Short 1-2 3.3 V (Default) Short 2-3 5 V

Table 4-8: LVDS2 Voltage Select Jumper Settings

2-pin header, p=2 mm

Table 4-8

See

Figure 4-10

See

Page 58

Page 72

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 4-10: LVDS2 Voltage Select Jumper Location

4.6.8 Serial Port Setting Jumper

Jumper Label: JP3 Jumper Type: Jumper Settings: Jumper Location:

Used for RS-232/422/485 communications.

Pin Description

Short 1-2 RS-232 (Default) Short 3-4 RS-422 Short 5-6 RS-485 Short 7-8 RS-485 use RTS Control

8-pin header, p=2 mm

Table 4-9

See

Figure 4-11

See

Table 4-9: Serial Port Jumper Settings

Page 59

Page 73

Figure 4-11: Serial Port Jumper Locations

4.7 Chassis Installation

KINO-PV-D5252/D4252 Mini ITX SBC

4.7.1 Airflow

WARNING:

Airflow is critical to the cooling of the CPU and other onboard components. The chassis in which the KINO-PV-D5252/D4252 must have air vents to allow cool air to move into the system and hot air to move out.

The KINO-PV-D5252/D4252 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface. In a system with an individual power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface.

4.7.2 Motherboard Installation

Page 60

To install the KINO-PV-D5252/D4252 motherboard into the chassis please refer to the reference material that came with the chassis.

Page 74

KINO-PV-D5252/D4252 Mini ITX SBC

4.8 Internal Peripheral Device Connections

This section outlines the installation of peripheral devices to the onboard connectors

4.8.1 AT/ATX Power Connection

Follow the instructions below to connect the KINO-PV-D5252/D4252 to an AT or ATX power supply.

WARNING:

Disconnect the power supply power cord from its AC power source to prevent a sudden power surge to the KINO-PV-D5252/D4252.

Step 1: Locate the power cable. The power cable is shown in the packing list in

Chapter 3.

Step 2: Connect the Power Cable to the Moth erboar d. Connect the 4 -pin (2x2) M olex

type power cable connector to the AT/ATX power connector on the motherboard.

Figure 4-12.

See

Figure 4-12: Power Cable to Motherboard Connection

Page 61

Page 75

Step 3: Connect Power Cable to Power Supply. Connect o ne of the 4-pi n (1x4) M olex

KINO-PV-D5252/D4252 Mini ITX SBC

type power cable connectors to an AT/ATX power supply. See

Figure 4-13.

Figure 4-13: Connect Power Cable to Power Supply

4.8.2 Single RS-232 Cable with Slot Bracket

The single RS-232 cable consists of one serial port connectors attached to a serial communications cable that is then attached to a D-sub 9 male connector that is mounted onto a bracket. To install the single RS-232 cable, please follow the steps below.

Step 1: Locate the connector. The location of the RS-232 connector is shown in

Chapter 3.

Step 2: Insert the cable connector. Insert the connector into the serial port box header.

Figure 4-14. A key on the front of the cable connectors ensures the

See connector can only be installed in one direction.

Page 62

Page 76

KINO-PV-D5252/D4252 Mini ITX SBC

Figure 4-14: Single RS-232 Cable Installation

Step 3: Secure the bracket. The single RS-232 connector has one D-sub 9 male

connector secured to a bracket. To secure the bracket to the chassis please refer to the reference material that came with the chassisStep 0:

4.9 Software Installation

All the drivers for the KINO-PV-D5252/D4252 are on the CD that came with the system. To install the drivers, please follow the steps below.

Step 1: Insert the CD into a CD drive connected to the system.

NOTE:

If the installation program doesn't start automatically: Click "Start->My Computer->CD Drive->autorun.exe"

Step 2: The driver main menu appears (Figure 4-15).

Page 63

Page 77

Figure 4-15: Introduction Screen

KINO-PV-D5252/D4252 Mini ITX SBC

Step 3: Click KINO-PV-D5252/D4252.

Step 4: A new screen with a list of available drivers appears (

Figure 4-16: Available Drivers

Figure 4-16).

Page 64

Step 5: Install all of the necessary drivers in this menu. Step 0:

Page 78

KINO-PV-D5252/D4252 Mini ITX SBC

5 BIOS Screens

Chapter

Page 65

Page 79

5.1 Introduction

The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed.

NOTE:

Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.

5.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.

KINO-PV-D5252/D4252 Mini ITX SBC

1. Press the

2. Press the the screen. 0.

If the message disappears before the F2 key is pressed, restart the computer and try again.

F2 key as soon as the system is turned on or F2 key when the “Press F2 to enter SETUP” message appears on

5.1.2 Using Setup

Use the arrow keys to highlight items, press ENTER to select, use the PageUp and PageDown keys to change entries, pres s F1 for help and press ESC to quit. Navigation

keys are shown in the following table.

Key Function

Up arrow Move to the item above Down arrow Move to item below Left arrow Move to the item on the left hand side

Page 66

Right arrow Move to the item on the right hand side + Increase the numeric value or make changes

- Decrease the numeric value or make changes

Page 80

KINO-PV-D5252/D4252 Mini ITX SBC

Key Function

Page up Move to the next page Page down Move to the previous page Esc Main Menu – Quit and do not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu

F1 General help, only for Status Page Setup Menu and Option

Page Setup Menu F9 Load optimized defaults F10 Save changes and Exit BIOS

Table 5-1: BIOS Navigation Keys

5.1.3 Getting Help

When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press E the F1 key again.

5.1.4 Unable to Reboot After Configuration Changes

If the computer cannot boot after changes to the system configuration is made, CMOS defaults. Use the jumper described in Chapter 4.

5.1.5 BIOS Menu Bar

The menu bar on top of the BIOS screen has the following main items:

 Main – Changes the basic system configuration.  Advanced – Changes the advanced system settings.  Chipset – Changes the chipset settings.  Boot – Changes the system boot configuration.

SC or

 Security – Sets User and Supervisor Passwords.  Save & Exit – Selects exit options and loads default settings

The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above.

Page 67

Page 81

KINO-PV-D5252/D4252 Mini ITX SBC

5.2 Main

The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information.

Main Advanced Chipset Boot Security Save & Exit

BIOS Information BIOS Vendor American Megatrends Core Version 4.6.4.0 0.20 Compliency UEFI 2.0 Project Version E350AR12.ROM Build Date 01/05/2011 20:25:34

System Date [Fri 04/16/2010] System Time [14:20:27]

Access Level Administrator

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 1: Main

Î BIOS Information

The BIOS Information lists a brief summary of the BIOS. The fields in BIOS Information cannot be changed. The items shown in the system overview include:

 BIOS Vendor: Installed BIOS vendor  Core Version: Current BIOS version  Project Version: The board version  Build Date and Time: Date the current BIOS version was made

The System Overview field also has two user configurable fields:

Î System Date [xx/xx/xx]

Use the System Date option to set the system date. Manually enter the day, month and year.

Page 68

Page 82

KINO-PV-D5252/D4252 Mini ITX SBC

Î System Time [xx:xx:xx]

Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.

5.3 Advanced

Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus:

WARNING!

Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.

Main Advanced Chipset Boot Security Save & Exit

> ACPI Settings > Trusted Computing > CPU Configuration > IDE Configuration > USB Configuration > Super IO Configuration > H/M Monitor > Secondary Super IO Configuration > Serial Port Console Redirection

BIOS Menu 2: Advanced

ÅÆ

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

: Select Screen

Page 69

Page 83

KINO-PV-D5252/D4252 Mini ITX SBC

5.3.1 ACPI Settings

The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and Power Interface (ACPI) options.

Advanced

ACPI Sleep State [S1 (CPU Stop Clock)]

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 3: ACPI Settings

Î ACPI Sleep State [S1 (CPU Stop Clo ck)]

Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used.

S1 (CPU Stop Clock)

S3 (Suspend to RAM)

DEFAULT

The system enters S1(POS) sleep state. The system appears off. The CPU is stopped; RAM is refreshed; the system is running in a low power mode.

The caches are flushed and the CPU is powered off. Power to the RAM is maintained. The computer returns slower to a working state, but more power is saved.

Page 70

Page 84

KINO-PV-D5252/D4252 Mini ITX SBC

5.3.2 Trusted Computing

Use the Trusted Computing menu (BIOS Menu 4) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM).

Advanced

TPM Configuration TPM SUPPORT [Disable]

Current TPM Status Information

NO TPM Hardware

nables or Disables TPM support. O.S. will not show TPM. Reset of platform is required.

----------------------

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 4: TPM Configuration

Î TPM Support [Disable]

Use the TPM Support option to configure support for the TPM.

Disable DEFAULT

Enable

TPM support is disabled. TPM support is enabled.

Page 71

Page 85

KINO-PV-D5252/D4252 Mini ITX SBC

5.3.3 CPU Configuration

Use the CPU Configuration menu (BIOS Menu 5) to view detailed CPU specifications and configure the CPU.

Advanced

CPU Configuration

Processor Type Intel(R) Atom(TM) CPU CPU D425 @ 1.80GHz EMT64 Supported Processor Speed 1800 MHz System Bus Speed 800 MHz Ratio Status 9 Actual Ratio 9 Processor Stepping 106ca Microcode Revision 263 L1 Cache RAM 56 k L2 Cache RAM 512 k Processor Core Single Hyper-Threading Supported

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 5: CPU Configuration

The CPU Configuration menu (BIOS Menu 5) lists the following CPU details:

 Processor Type: Lists the brand name of the CPU being used  EMT64: Indicates if EM64T is supported by the CPU.  Processor Speed: Lists the CPU processing speed  System Bus: Lists the system bus  Ratio Status: List the maximum FSB divisor  Actual Ratio: Lists current FSB divisor  Processor Stepping: Lists the CPU processing stepping  Microcode Revision: Lists the microcode revision  L1 Cache RAM: Lists the CPU L1 cache size  L2 Cache RAM: Lists the CPU L2 cache size  Processor Core: Lists the number of the processor core  Hyper-Threading: Indicates if Intel Hyper-Threading Technology is supported

by the CPU.

Page 72

Page 86

KINO-PV-D5252/D4252 Mini ITX SBC

5.3.4 IDE Configuration

Use the IDE Configuration menu (BIOS Menu 6) to change and/or set the configuration of the ATA/IDE devices installed in the system.

Advanced

PATA Master Not Present PATA Slave Not Present

SATA Port0 Not Present SATA Port1 Not Present SATA Port2 Not Present SATA Port3 Not Present

ATA/IDE Configuration [Enhanced]

Configure SATA as [IDE]

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 6: IDE Configuration

Î ATA/IDE Con figura tions [Enhance d]

Use the ATA/IDE Configurations option to configure the ATA/IDE controller.

Disabled

Compatible

Enhanced DEFAULT

Disables the on-board ATA/IDE controller. Configures the on-board ATA/IDE controller to be in

compatible mode. In this mode, a SATA channel will replace one of the IDE channels. This mode supports up to 4 storage devices.

Configures the on-board ATA/IDE controller to be in Enhanced mode. In this mode, IDE channels and SATA channels are separated. This mode supports up to 6 storage devices. Some legacy OS do not support this mode.

Page 73

Page 87

Î Configure SATA as [IDE]

Use the Configure SATA as option to configure SATA devices as normal IDE devices.

KINO-PV-D5252/D4252 Mini ITX SBC

IDE DEFAULT

AHCI

Configures SATA devices as normal IDE device. Configures SATA devices as AHCI device.

5.3.5 USB Configuration

Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and configure the USB settings.

Advanced

USB Configuration

USB Devices: None

Legacy USB Support [Enabled]

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 7: USB Configuration

Î USB Devi ces

The USB Devices Enabled field lists the USB devices that are enabled on the system

Î Legacy USB Support [Enabled]

Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system.

Page 74

Page 88

KINO-PV-D5252/D4252 Mini ITX SBC

Enabled DEFAULT

Disabled

Auto

Legacy USB support enabled Legacy USB support disabled Legacy USB support disabled if no USB devices are

connected

5.3.6 Super IO Configuration

Use the Super IO Configuration menu (BIOS Menu 8) to set or change the configurations for the FDD controllers, parallel ports and serial ports.

Advanced

Super IO Configuration

Super IO Chip Fintek F81865

> Serial Port 0 Configuration > Serial Port 1 Configuration > Serial Port 2 Configuration > Serial Port 3 Configuration > Parallel Port Configuration

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 8: Super IO Configuration

Page 75

Page 89

KINO-PV-D5252/D4252 Mini ITX SBC

5.3.6.1 Serial Port 0 Configuration

Use the Serial Port 0 Configuration menu (BIOS Menu 9) to configure the serial port 0.

Advanced

Serial Port 0 Configuration

Serial Port [Enabled]

Device Settings IO=3F8h; IRQ=4

Change Settings [Auto]

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 9: Serial Port 0 Configuration Menu

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Auto DEFAULT

IO=3F8h;

Disable the serial port Enable the serial port

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 3F8h and the interrupt

Page 76

IRQ=4

IO=3F8h; IRQ=3, 4

address is IRQ4 Serial Port I/O port address is 3F8h and the interrupt

address is IRQ3 and IRQ4

Page 90

KINO-PV-D5252/D4252 Mini ITX SBC

IO=2F8h; IRQ=3, 4

5.3.6.1.1 Serial Port 1 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled

Enabled DEFAULT

Î Devi ce Mode

Use the Device Mode option to set the Serial Port 1 signaling mode.

RS232 DEFAULT

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3 and IRQ4

Disable the serial port Enable the serial port

Serial Port 1 signaling mode is RS-232

RS485

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Auto DEFAULT

IO=2F8h; IRQ=3

IO=3F8h; IRQ=3, 4

IO=2F8h; IRQ=3, 4

Serial Port 1 signaling mode is RS-422/RS-485

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3

Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3, 4

Page 77

Page 91

5.3.6.1.2 Serial Port 2 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

KINO-PV-D5252/D4252 Mini ITX SBC

Disabled

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Auto DEFAULT

IO=3E8h; IRQ=11

IO=3E8h; IRQ=10, 11

IO=2E8h; IRQ=10, 11

Disable the serial port Enable the serial port

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 3E8h and the interrupt address is IRQ11

Serial Port I/O port address is 3E8h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2E8h and the interrupt address is IRQ10, 11

5.3.6.1.3 Serial Port 3 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Page 78

Disable the serial port Enable the serial port

Page 92

KINO-PV-D5252/D4252 Mini ITX SBC

Auto DEFAULT

IO=2E8h; IRQ=10

IO=3E8h; IRQ=10, 11

IO=2E8h; IRQ=10, 11

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 2E8h and the interrupt address is IRQ10

Serial Port I/O port address is 3E8h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2E8h and the interrupt address is IRQ10, 11

5.3.6.2 Parallel Port Configuration

Use the Parallel Port Configuration menu (BIOS Menu 9) to configure the serial port n.

Advanced

Parallel Port Configuration

Parallel Port [Enabled]

Device Settings IO=378h; IRQ=7

Change Settings [Auto] Device Mode [Printer Mode]

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 10: Parallel Port Configuration Menu

Î Parallel Port [Enabled]

Use the Parallel Port option to enable or disable the parallel port.

Disabled

Enabled DEFAULT

Disable the parallel port Enable the parallel port

Page 79

Page 93

Î Change Settings [Auto]

Use the Change Settings option to change the parallel port IO port address and interrupt address.

KINO-PV-D5252/D4252 Mini ITX SBC

Auto DEFAULT

IO=378h; IRQ=7

IO=278h; IRQ=7

IO=3BCh IRQ=7

Î Devi ce Mode [Printer Mode]

Use the Device Mode option to select the mode the parallel port operates in. Configuration options are listed below.

The parallel port IO port address and interrupt address are automatically detected.

Parallel Port I/O port address is 378h and the interrupt address is IRQ7

Parallel Port I/O port address is 278h and the interrupt address is IRQ7

Parallel Port I/O port address is 3BCh and the interrupt address is IRQ7

Page 80

 Printer Mode Default  SPP Mode  EPP-1.9 and SPP Mode  EPP-1.7 and SPP Mode  ECP Mode  ECP and EPP 1.9 Mode  ECP and EPP 1.7 Mode

Page 94

KINO-PV-D5252/D4252 Mini ITX SBC

5.3.7 H/W Monitor

The H/W Monitor menu (BIOS Menu 11) shows the operating temperature, fan speeds and system voltages.

Advanced

PC Health Status

CPU Temperature :+39 C SYS Temperature :+40 C CPU FAN Speed :4950 RPM SYS FAN Speed :2762 RPM VCC3V :+3.312 V V_core :+1.104 V Vcc :+4.961 V Vcc12 :+11.176 V V1_5VDDR :+1.776 V VSB3V :+3.312 V VBAT :+3.232 V

CPU Smart Fan control [Auto Mode] Temperature Bound1 60 Temperature Bound2 50 Temperature Bound3 40 Temperature Bound4 30 SYS Smart Fan control [Auto Mode] Temperature Bound1 60 Temperature Bound2 50 Temperature Bound3 40 Temperature Bound4 30

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 11: Hardware Health Configuration

Î PC Health Status

The following system parameters and values are shown. The system parameters that are monitored are:

 System Temperatures:

 Fan Speeds:

o CPU Temperature o System Temperature

o CPU Fan Speed o SYS Fan Speed

Page 81

Page 95

 Voltages:

o VCC3V o V_core o Vcc o Vcc12 o Vcc1_5VDDR o VSB3V o VBAT

Î CPU Smart Fan control [Auto Mode]

Use the CPU Smart Fan control option to configure the CPU fan.

KINO-PV-D5252/D4252 Mini ITX SBC

Auto Mode

Manual Mode

Î SYS Smart Fan control [Auto Mode]

Use the SYS Smart Fan control option to configure the SYS fan.

Auto Mode

The fan adjusts its speed using these settings: Temperature Bound 1

Temperature Bound 2 Temperature Bound 3 Temperature Bound 4

The fan spins at the speed set in: Manual Duty Cycle Setting

The fan adjusts its speed using these settings: Temperature Bound 1

Temperature Bound 2 Temperature Bound 3

Page 82

Manual Mode

Temperature Bound 4 The fan spins at the speed set in:

Manual Duty Cycle Setting

Page 96

KINO-PV-D5252/D4252 Mini ITX SBC

5.3.8 Secondary Super IO Configuration

The Secondary Super IO Configuration (BIOS Menu 13) displays IO chip type and the submenus for configuring the external SATA ports 5 and 6.

Advanced

Secondary Super IO Configuration

Super IO Chip Fintek F81216 > Serial Port 5 Configuration > Serial Port 6 Configuration

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 12: Secondary Super IO Configuration

5.3.8.1 Serial Port 5 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Auto DEFAULT

Disable the serial port Enable the serial port

The serial port IO port address and interrupt address are automatically detected.

Page 83

Page 97

KINO-PV-D5252/D4252 Mini ITX SBC

IO=2C0h; IRQ=11

IO=2C0h; IRQ=10, 11

IO=2C8h; IRQ=10, 11

IO=2D0h; IRQ=10, 11

IO=2D8h; IRQ=10, 11

IO=2E0h; IRQ=10, 11

Serial Port I/O port address is 2C0h and the interrupt address is IRQ11

Serial Port I/O port address is 2C0h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2C8h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2D0h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2D8h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2E0h and the interrupt address is IRQ10, 11

5.3.8.2 Serial Port 6 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled

Enabled DEFAULT

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Auto DEFAULT

IO=2E0h; IRQ=10

IO=2C0h;

Disable the serial port Enable the serial port

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 2E0h and the interrupt address is IRQ10

Serial Port I/O port address is 2C0h and the interrupt

Page 84

IRQ=10, 11

address is IRQ10, 11

Page 98

KINO-PV-D5252/D4252 Mini ITX SBC

IO=2C8h; IRQ=10, 11

IO=2D0h; IRQ=10, 11

IO=2D8h; IRQ=10, 11

IO=2E0h; IRQ=10, 11

Serial Port I/O port address is 2C8h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2D0h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2D8h and the interrupt address is IRQ10, 11

Serial Port I/O port address is 2E0h and the interrupt address is IRQ10, 11

5.3.9 Serial Port Console Redirection

The Serial Port Console Redirection menu (BIOS Menu 13) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port.

Advanced

COM0

Console Redirection [Disabled]

> Console Redirection Settings

COM1

Console Redirection [Disabled]

> Console Redirection Settings

COM2

Console Redirection [Disabled]

> Console Redirection Settings

COM3

Console Redirection [Disabled]

> Console Redirection Settings

COM4

Console Redirection [Disabled]

> Console Redirection Settings

COM5

Console Redirection [Disabled]

> Console Redirection Settings

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 13: Serial Port Console Redirection

Page 85

Page 99

Î Console Redirection [Disabled]

Use Console Redirection option to enable or disable the console redirection fun ction.

KINO-PV-D5252/D4252 Mini ITX SBC

Disabled DEFAULT

Enabled

Disabled the console redirection function Enabled the console redirection function

5.4 Chipset

Use the Chipset menu (BIOS Menu 14) to access the Northbridge and Southbridge configuration menus

WARNING!

Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.

Main Advanced Chipset Boot Security Save & Exit

> Host Bridge > South Bridge > Intel ICD SWSCI OpRegion

ÅÆ

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

: Select Screen

Page 86

BIOS Menu 14: Chipset

Page 100

KINO-PV-D5252/D4252 Mini ITX SBC

5.4.1 Host Bridge Configuration

Use the Host Bridge Configuration menu (BIOS Menu 15) to configure the Northbridge chipset.

Chipset

> Memory Frequency and Timing > OnChip VGA Configuration

MMIO Size [AUTO]

Initate Graphic Adapter [IGD]

******* Memory Information ******* Memory Frequency 800 Mhz

Total Memory 2048 MB

DIMM#0 2048 MB DIMM#1 Not Present

ÅÆ

: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit

BIOS Menu 15: Host Bridge Chipset Configuration

Î MMIO Size

Use the MMIO Size option to set the MMIO reserve memory size.

AUTO DEFAULT

1GB

2GB

Î Initate Graphic Adapter [IGD]

Use Initate Graphic Adapter option to select which graphics controller to use as the primary boot device. Select either an ION graphics controller or a combination of PCI graphics controller and PCI express (PEG) controller. Configuration options are listed in the table below:

Enables ION graphics controller. Enables PCI/PEG graphics controller.

Page 87

IEI Technology KINO-PV-D5252, KINO-PV-D4252 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Introduction

1.1 Introduction

1.2 Connectors

1.3 Dimensions

1.4 Data Flow

1.5 Technical Specifications

2 Unpacking

2.1 Anti-static Precautions

2.2 Unpacking Precautions

2.3 Packing List

2.3.1 Optional Items

3 Connectors

3.1 Peripheral Interface Connectors

3.1.1 KINO-PV -D5252/D4252 Layout

3.1.2 Peripheral Interface Connectors

3.1.3 External Interface Panel Connectors

3.2 Internal Peripheral Connectors

3.2.1 12V Power Connector

3.2.2 Battery Connector

3.2.3 CompactFlash® Slot

3.2.4 Digital I/O Connector

3.2.5 Fan Connector (CPU)

3.2.6 Fan Connector

3.2.7 Flash SPI ROM

3.2.8 Front Panel Connector

3.2.9 Keyboard/Mouse Connector

3.2.10 Keypad Connector

3.2.11 LVDS1 Connector (For Intel® Atom™ processor D525 dual LVDS only)

3.2.12 LVDS1 Backlight Inverter Connector

3.2.13 LVDS2 Connector

3.2.14 LVDS2 Backlight Inverter Connector

3.2.15 Parallel Port Connector

3.2.16 PCIe Mini Card Slot

3.2.17 SATA Drive Connectors

3.2.18 SATA Power Connectors

3.2.19 Serial Port Connectors (RS-232)

3.2.20 Serial Port Connector (RS-232)

3.2.21 SMBus Connector

3.2.22 USB Connectors

3.3 External Peripheral Interface Connector Panel

3.3.1 Audio Connector

3.3.2 Ethernet and USB Connector

3.3.3 Power Connector

3.3.4 Serial Port Connector

3.3.5 VGA Port Connector

4 Installation

4.1 Anti-static Precautions

4.2 Installation Considerations

4.2.1 Installation Notices

4.3 Unpacking

4.4 SO-DIMM Installation

4.4.1 SO-DIMM Installation

4.5 CompactFlash® Installation

4.6 Jumper Settings

4.6.1 AT/ATX Power Select Jumper Settings

4.6.2 Clear CMOS Jumper

4.6.3 CompactFlash® Card Setup Jumper

4.6.4 LVDS1 Panel Resolution Type Select Jumper (For Intel® Atom™ processor D525 dual LVDS only)

4.6.5 LVDS2 Panel Resolution Select Jumper

4.6.6 LVDS1 Voltage Select setting

4.6.7 LVDS2 Voltage Select setting

4.6.8 Serial Port Setting Jumper

4.7 Chassis Installation

4.7.1 Airflow

4.7.2 Motherboard Installation

4.8 Internal Peripheral Device Connections

4.8.1 AT/ATX Power Connection

4.8.2 Single RS-232 Cable with Slot Bracket

4.9 Software Installation

5 BIOS Screens

5.1 Introduction

5.1.1 Starting Setup

5.1.2 Using Setup

5.1.3 Getting Help

5.1.4 Unable to Reboot After Configuration Changes

5.1.5 BIOS Menu Bar