Page 1
IVC-100/120-RS, PM-1056-4P QIG
PM-1056 Hardware Diagrams
PM-1056-4PG/4PGB
PM-1056-4P/PM-1056-4PB
w/o GPIO (CN1)
The driver program and operation of PM-1056-4P/4PB/4PG/4PGB and IVC-100/G are the same. PM1056-4P/4PB/4PG/4PGB is the interface of PCI/104.
PCI Signal Grouping Selection
x SW1 (Rotary Switch): Group selection of PCI configuration for PCI/104 modules
Group SW1 Position
0 0, 4
1 1, 5
2 2, 6
3 3, 7
x Signal Grouping Description
Group PCICLK ID Address INT0 INT1 REQ GNT
0 PCICLK0 IDSEL0 INTA INTB REQ0 GNT0
1 PCICLK1 IDSEL1 INTB INTC REQ1 GNT1
2 PCICLK2 IDSEL2 INTC INTD REQ2 GNT2
3 PCICLK3 IDSEL3 INTD INTA REQ3* GNT3*
*Note: REQ3# and GNT#3 are not signals defined in PC/104-PLUS.
Do not use MODE3 if your card does not have these signals on PC/104-PLUS connector.
8
IVC-100/120-RS, PM-1056-4P QIG
4-Channel Video Capture Card with GPIO Module
IVC-100/200-RS
PM-1056-4P-RS
Quick Installation Guide
Version 2.0
May. 17, 2006
Package Contents
IVC-100/200 package includes the following items:
x Video capture card x 1
x CD x 1
x Hard copy of user manual x 1
x GPIO module: (for IVC-100G and IVC-200G only)
GPIO daughter board x 1, flat cable x 1, input connector x 1 and
output connector x 1
©2006 Copyright by IEI Technology Corp.
All rights reserved.
1
GPIO pin connector
4PORT Video output
connector
LED
Rotary Switch
Jumper
PC104PLU
S
connector
Page 2
IVC-100/120-RS, PM-1056-4P QIG
Specifications
z Function: PCI Single Universal Board
Plug and Play, 4 channel video capture card
z Analog Video Capture Engine: Conexant Fusion TM 878A
NTSC/ PAL / SECAM Video Decoding
z Input/Output Interface:
Video Input: pin connector for 4 channels BNC Connector
Video Output : One channel Video Output selected from the driver GPIO: 4 inputs and 4
outputs (use CT-800 GPIO daughter board)
z Functionality Support:
Multiple Video Resolutions
NTSC: 720x480, 704x480, 640x480, 352x240, 320x240, 176x112
PAL: 720x576, 704x576, 640x576,352x288, 320x288, 176x144
Capture Frame Rate-Max 30 fps for 4 channels
Support Video Loss Detection Multi-screen support
Support resolution adjustment
Support image brightness, contrast, and saturation adjustment
LED for card ID configuration and identification
z Software Support: Provide WDM driver and SDK for developer
z Supporting OS: Window 98 SE, ME, 2000, XP,Linux
z Others: Power Consumption: 3.5W@5V
Operating Temperature: 0~ 50oC
Board Size: 120.19mm x 100m
Ordering Information
IVC-100
4 Channels Video Capture card(30 FPS)
IVC-100G
4 Channels Video Capture card(30 FPS) with GPIO module
IVC-200
High-end 4 channels video capture card(120FPS)
IVC-200G
High-end 4 channels video capture card(120FPS) with GPIO module
PM-1056-4P
PCI/104 4 Channels Video Capture Module (30 FPS)
PM-1056-4PG
PCI/104 4 Channels Video Capture Module (30 FPS) with GPIO modu
le
2
IVC-100/120-RS, PM-1056-4P QIG
i. Double click “Demo” folder.
ii. Double click “ivc-200.exe”.
iii. Click “Select Device” to choose the video capture card.
iv. Click “Video Size” to choose the resolution. The available resolutions are 160 x 120 and 320
x 240.
v. Click “Video Channel” to activate the video input channels.
vi. Click “GPIO” to control the input/output devices
Recording the Captured Image
i. Open the folder Demo and double click amcap.exe.
ii. Click Devices to select the video capture card.
iii. Click “Options and then Preview to view the captured image.
iv. Click Video Crossbar then select the recording channel from the Input list.
v. Click Capture then Start Capture.
vi. Set the directory and folder to save the captured file. Then click OK to start recording the
video image.
vii. Click Stop Capture to stop recording.
Uninstalling the Program
i. Click Start then choose Settings and double click Control Panel.
ii. Double click Add/Remove Programs.
iii. Select the software of Video Capture Card and click Add/Remove.
iv. Click Yes to uninstall the Video Capture Card software.
v. Select “Restart my computer now” and click Finish
7
Page 3
IVC-100/120-RS, PM-1056-4P QIG
Demo Programs
Video Image Preview for IVC-100G/100
To preview a video image, follow the steps below:
i. Double click Demo folder.
ii. Double click ivc-100.exe.
iii. Click Select Device to choose the video capture card.
iv. Click Video Size to choose the resolution. The available resolutions are 160 x 120 and 320 x 240.
v. Click Video Channel to activate the video input channels.
vi. Click GPIO to control the input/output devices.
Video Image Preview for IVC-200G/200
6
IVC-100/120-RS, PM-1056-4P QIG
Hardware Connections & Settings Illustration for Video
Capture Card
IVC-100G GPIO = general purpose input output
IVC-100
IVC-200G GPIO = general purpose input output
3
GPIO
pin
Jump
LED
BNC
Jum
p
LED
BNC
Jum
p
GPIO
pin
Page 4
IVC-100/120-RS, PM-1056-4P QIG
IVC-200
Connections to the Video Source
Connect your video source to the BNC connector of the video capture card. Take
IVC-100G for example:
x IVC-100G
LED Jumper Settings
The jumper setting controls the card number on the LED.
Jumper Setting Table
L
ogic 1 = ON
L
ogic 0 = OFF
BNC
LED
Video Source
4
IVC-100/120-RS, PM-1056-4P QIG
1 2 3 4 Card Number on the LED
1 1 1 1 0
0 1 1 1 1
1 0 1 1 2
0 0 1 1 3
1 1 0 1 4
0 1 0 1 5
1 0 0 1 6
0 0 0 1 7
1 1 1 0 8
0 1 1 0 9
1 0 1 0 A
0 0 1 0 B
1 1 0 0 C
0 1 0 0 D
1 0 0 0 E
0 0 0 0 F
Installation Procedures-Driver Installation
IEI driver installation program makes the driver installation of multiple cards
an easy job. The steps of driver installation are described as below:
Steps:
i. Adjust the jumper setting of the video capture card.
ii. Insert the video capture card(s) into the computer system, and then turn on the computer.
iii. The system will find a new device on the syste m and ask you to install the driver. Click
Cancel to close the dialog box.
iv. Run the program ieisetup.exe from the IEI Installation CD.
v. The window will show a welcome message for in stallation. Click the Next button for next
step.
vi. The window will then show a message of current configuration, click Next to start the
installation.
vii. The window will show a message to
warn you that the software does not
contain a Microsoft digital signature.
Click Yes to continue the installation.
viii. There will be another window
message to ask you to install an audio
driver. Click Yes to continue.
ix. For multi-card system, you will be
asked to install video and audio
drivers for every card in your system.
Click Yes to continue the installation.
x. After the driver has been successfully installed, click Finish.
xi. Restart your computer when you finish installing DirectX.
5
Loading...