IEI Technology ITG-100AI User Manual

Download

Page 1

ITG-100AI Embedded System

Page i

MODEL:

ITG-100AI

Fanless Embedded System with Intel® Atom™ x5-E3930,

Rev. 1.00 – October 2, 2019

VGA , GbE, Two RS-232/422/485,

Two USB 3.0 and RoHS Compliant

User Manual

Page 2

ITG-100AI Embedded System

Page ii

Date Version Changes

October 2, 2019 1.00 Initial release

Revision

Page 3

ITG-100AI Embedded System

Page iii

The information in this document is subject to change without prior notice in order to

improve reliability, design and function and does not represent a commitment on the part

of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

reserved. No part of this manual may be reproduced by any mechanical, electronic, or

other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification

purposes only and may be trademarks and/or registered trademarks of their respective

owners.

Page 4

ITG-100AI Embedded System

Page iv

Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the

equipment or result in personal injury. Warnings should be taken

seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of

losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical

information. These messages should be read carefully as any directions

or instructions contained therein can help avoid making mistakes.

HOT SURFACE

This symbol indicates a hot surface that should not be touched without

taking care.

Page 5

ITG-100AI Embedded System

Page v

Table of Contents

1 INTRODUCTION .......................................................................................................... 1

1.1 OVERVIEW .................................................................................................................. 2

1.2 FEATURES ................................................................................................................... 2

1.3 TECHNICAL SPECIFICATIONS ...................................................................................... 3

1.4 SIDE PANEL ................................................................................................................ 4

1.5 FRONT PANEL ............................................................................................................. 5

1.6 PHYSICAL DIMENSIONS .............................................................................................. 6

2 UNPACKING ................................................................................................................. 7

2.1 UNPACKING ................................................................................................................ 8

2.2 PACKING LIST ............................................................................................................. 8

3 INSTALLATION ......................................................................................................... 10

3.1 ANTI-STATIC PRECAUTIONS ....................................................................................... 11

3.2 INSTALLATION PRECAUTIONS .................................................................................... 11

3.3 BOTTOM COVER REMOVAL AND RE-INSTALLATION .................................................. 12

3.4 SO-DIMM INSTALLATION ....................................................................................... 13

3.5 WIRELESS LAN MODULE INSTALLATION (OPTIONAL) ............................................. 15

3.6 RS-232/422/485 SERIAL PORT CONNECTION ........................................................... 17

3.6.1 DB-9 RS-232/422/485 Serial Port Connection ................................................ 17

3.6.2 RJ-45 RS-232/422/485 Serial Port Connection ............................................... 18

3.7 AT/ATX MODE SELECTION ...................................................................................... 21

3.7.1 AT Power Mode ................................................................................................ 21

3.7.2 ATX Power Mode ............................................................................................. 22

3.8 MOUNTING THE SYSTEM .......................................................................................... 22

3.9 POWERING ON/OFF THE SYSTEM ............................................................................. 24

3.10 RESET THE SYSTEM ................................................................................................ 24

4 BIOS .............................................................................................................................. 25

4.1 INTRODUCTION ......................................................................................................... 26

4.1.1 Starting Setup ................................................................................................... 26

Page 6

ITG-100AI Embedded System

Page vi

4.1.2 Using Setup ...................................................................................................... 26

4.1.3 Getting Help ..................................................................................................... 27

4.1.4 Unable to Reboot after Configuration Changes .............................................. 27

4.1.5 BIOS Menu Bar ................................................................................................ 27

4.2 MAIN ........................................................................................................................ 28

4.3 ADVANCED ............................................................................................................... 29

4.3.1 ACPI Settings ................................................................................................... 30

4.3.2 F81866 Super IO Configuration ...................................................................... 31

4.3.2.1 Serial Port n Configuration ....................................................................... 31

4.3.3 Hardware Monitor ........................................................................................... 33

4.3.4 RTC Wake Settings ........................................................................................... 34

4.3.5 Serial Port Console Redirection ...................................................................... 36

4.3.5.1 Console Redirection Settings .................................................................... 36

4.3.6 CPU Configuration .......................................................................................... 39

4.3.7 USB Configuration ........................................................................................... 40

4.3.8 iEi Feature ........................................................................................................ 41

4.3.9 SATA Configuration ......................................................................................... 42

4.4 CHIPSET ................................................................................................................... 43

4.4.1 North Bridge Configuration ............................................................................. 44

4.4.1.1 Intel IGD Configuration ............................................................................ 44

4.4.2 Southbridge Configuration .............................................................................. 46

4.4.2.1 PCI Express Configuration ....................................................................... 47

4.4.2.2 SCC Configuration .................................................................................... 48

4.5 SECURITY ................................................................................................................. 49

4.6 BOOT ........................................................................................................................ 50

4.7 EXIT ......................................................................................................................... 52

5 SOFTWARE INSTALLATION .................................................................................. 54

5.1 AVAILABLE DRIVERS ................................................................................................ 55

5.1.1 Driver Download ............................................................................................. 55

5.2 OPENVINO™ TOOLKIT INSTALLATION .................................................................... 57

A REGULATORY COMPLIANCE .............................................................................. 58

B SAFETY PRECAUTIONS ......................................................................................... 63

B.1 SAFETY PRECAUTIONS ............................................................................................. 64

Page 7

ITG-100AI Embedded System

Page vii

B.1.1 General Safety Precautions ............................................................................. 64

B.1.2 Anti-static Precautions .................................................................................... 65

B.1.3 Product Disposal ............................................................................................. 66

B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 67

B.2.1 Maintenance and Cleaning .............................................................................. 67

B.2.2 Cleaning Tools ................................................................................................. 67

C BIOS MENU OPTIONS ............................................................................................. 69

D TERMINOLOGY ....................................................................................................... 72

E HAZARDOUS MATERIALS DISCLOSURE ......................................................... 76

Page 8

ITG-100AI Embedded System

Page viii

List of Figures

Figure 1-1: ITG-100AI ..................................................................................................................... 2

Figure 1-2: ITG-100AI Side Panel .................................................................................................. 4

Figure 1-3: ITG-100AI Front Panel ................................................................................................. 5

Figure 1-4: Physical Dimensions (mm) ........................................................................................ 6

Figure 3-1: Bottom Cover Retention Screws ............................................................................. 12

Figure 3-2: Bottom Cover Installation ........................................................................................ 13

Figure 3-3: SO-DIMM Socket ....................................................................................................... 14

Figure 3-4: SO-DIMM Installation ................................................................................................ 14

Figure 3-5: Accelerator Card Retention Screws ........................................................................ 15

Figure 3-6: WLAN M.2 Card Slot Location ................................................................................. 16

Figure 3-7: Inserting the WLAN Card into the Slot at an Angle ............................................... 16

Figure 3-8: Securing the WLAN Card ......................................................................................... 17

Figure 3-9: Serial Device Connector ........................................................................................... 18

Figure 3-10: DB-9 RS-232/422/485 Serial Port Connector ........................................................ 18

Figure 3-11: Serial Device Connector ......................................................................................... 19

Figure 3-12: RJ-45 RS-232/422/485 Serial Port Connector ....................................................... 19

Figure 3-13: DB-9 RS-232/422/485 Connector Pinout Location ............................................... 20

Figure 3-14: AT/ATX Switch Location ......................................................................................... 21

Figure 3-15: Mounting the DIN Rail ............................................................................................. 23

Figure 3-16: Mounting to DIN Rail ............................................................................................... 23

Figure 3-17: Power Button Location ........................................................................................... 24

Figure 3-18: Reset Button Location ............................................................................................ 24

Figure 5-1: IEI Resource Download Center ................................................................................ 55

Page 9

ITG-100AI Embedded System

Page ix

List of Tables

Table 1-1: Technical Specifications .............................................................................................. 4

Table 2-1: Package List Contents ................................................................................................. 9

Table 3-1: RJ-45 RS-232/422/485 Serial Port Pinouts ............................................................... 19

Table 3-2: DB-9 RS-232/422/485 Connector Pinouts ................................................................. 20

Table 4-1: BIOS Navigation Keys ................................................................................................ 27

Page 10

ITG-100AI Embedded System

Page x

BIOS Menus

BIOS Menu 1: Main ....................................................................................................................... 28

BIOS Menu 2: Advanced .............................................................................................................. 29

BIOS Menu 3: ACPI Configuration .............................................................................................. 30

BIOS Menu 4: Super IO Configuration ........................................................................................ 31

BIOS Menu 5: Serial Port 1 Configuration Menu ....................................................................... 31

BIOS Menu 6: Hardware Monitor ................................................................................................. 34

BIOS Menu 7: RTC Wake Settings .............................................................................................. 35

BIOS Menu 8: Serial Port Console Redirection ......................................................................... 36

BIOS Menu 9: Console Redirection Settings ............................................................................. 37

BIOS Menu 10: CPU Configuration ............................................................................................. 39

BIOS Menu 11: USB Configuration ............................................................................................. 40

BIOS Menu 12: iEi Feature ........................................................................................................... 41

BIOS Menu 13: IDE Configuration ............................................................................................... 42

BIOS Menu 14: Chipset ................................................................................................................ 43

BIOS Menu 15: Northbridge Chipset Configuration .................................................................. 44

BIOS Menu 16: Integrated Graphics ........................................................................................... 45

BIOS Menu 17: Southbridge Chipset Configuration ................................................................. 46

BIOS Menu 18: PCI Express Configuration ............................................................................... 47

BIOS Menu 19: PCI Express Configuration ............................................................................... 48

BIOS Menu 20: Security ............................................................................................................... 49

BIOS Menu 21: Boot ..................................................................................................................... 50

BIOS Menu 22:Exit ........................................................................................................................ 52

Page 11

ITG-100AI Embedded System

Page 1

Chapter

1 Introduction

Page 12

ITG-100AI Embedded System

Page 2

1.1 Overview

Figure 1-1: ITG-100AI

The ITG-100AI embedded system is a fanless system with one VGA port for display. It

accepts an Intel® Atom™ x5-E3930 processor and supports one 204-pin DDR3L

SO-DIMM module pre-installed with 8 GB memory. Two RS-232/422/485 serial ports

and two USB 3.1 GEN 1 ports ensure simplified connectivity to a variety of external

peripheral devices.

1.2 Features

The ITG-100AI features are listed below:

 Intel® Atom™ x5-E3930 1.3GHz (up to 1.8 GHz)

 Two GbE LAN ports

 Two RS-232/422/485

 M.2 A-key slot for expansion

 Pre-installed Mustang-MPCIE-MX2 , 2 x Intel Myriad X

VPU for AI deep learning workload consolidation

Page 13

ITG-100AI Embedded System

Page 3

1.3 Technical Specifications

The ITG-100AI technical specifications are listed in Table 1-1.

Model Name ITG-100AI

AI Accelerator

Chassis

Color

Dimensions (WxDxH)

System Fan

Chassis Construction

Motherboard

CPU

Chipset

System Memory

Storage

SATADOM

eMMC

Mustang-MPCIE-MX2

Blue & Silver

137 x 102.8 x 50 (mm)

Fanless

Extruded aluminum alloy

Intel® Atom™ x5-E3930 1.3 GHz (up to 1.8GHz, dual-core, TDP=6.5W)

SoC

1x 204-pin DDR3L SO-DIMM slot pre-installed with 8 GB memory

Pre-installed 128GB

1 x eMMC 5.0 support (up to 32GB optional)

Micro SD

I/O Interfaces

USB 3.1 Gen 1 (5Gb/s)

Ethernet

COM Port

Display

Resolution

Wireless

Others

Expansions

1 x Micro SD Slot

2 x USB 3.1 GEN 1 ports

2 x RJ-45 PCIe GbE by I211-AT controller

2 x RS-232/422/485 (DB-9/RJ45)

1 x VGA

Up to 1920x1080@60Hz

1 x 802.11a/b/g/n/ac (optional)

1 x Power Button, 1 x Reset Button, 1 x AT/ATX Switch,

1 x LED for HDD (Yellow),1 x LED for Power (Green)

Page 14

ITG-100AI Embedded System

Page 4

M.2

Power

Power Input

Reliability

Mounting

Operating Temperature

Storage Temperature

Operating Shock

Operating Vibration

Safety / EMC

Watchdog Timer

Supported OS

1 x M.2 2230 (A key, PCIe by 1, USB2.0)

2-pin terminal block: 9~36V DC-in

DIN-rail

-20°C ~ 50°C with air flow, 10% ~ 95%, non-condensing

-20°C ~ 70°C with air flow, 10% ~ 90%, non-condensing

Half-sine wave shock 5G, 11ms, 100 shocks per axis, IEC68-2-27

MIL-STD-810G 514.6C-1

CE/FCC

Programmable 1~255 sec/min

Win10/Linux Ubuntu 16.04 LTS

Table 1-1: Technical Specifications

1.4 Side Panel

The side panel of the ITG-100AI has the following features (Figure 1-2):

 1 x 9~36V DC IN

 1 x VGA connector

Figure 1-2: ITG-100AI Side Panel

Page 15

ITG-100AI Embedded System

Page 5

1.5 Front Panel

The front panel of the ITG-100AI has the following features (Figure 1-3):

 1 x AT/ATX Switch

 1 x HDD LED

 1 x Power button

 1 x Power LED

 1 x Reset button

 2 x RJ-45 LAN connectors

 2 x RS-232/422/485 serial port connectors (DB-9/RJ45)

 2 x USB 3.1 GEN 1 connectors

Figure 1-3: ITG-100AI Front Panel

Page 16

ITG-100AI Embedded System

Page 6

1.6 Physical Dimensions

The physical dimensions of the ITG-100AI are shown below:

Figure 1-4: Physical Dimensions (mm)

Page 17

ITG-100AI Embedded System

Page 7

Chapter

2 Unpacking

Page 18

ITG-100AI Embedded System

Page 8

from or contact an IEI sales

2.1 Unpacking

To unpack the embedded system, follow the steps below:

Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the

external (second) box.

Step 2: Open the external (second) box.

Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the

internal (first) box.

Step 4: Lift the system out of the boxes.

Step 5: Remove both polystyrene ends, one from each side.

Step 6: Make sure all the components listed in the packing list are present.

2.2 Packing List

NOTE:

If some of the components listed in the checklist below are missing,

please do not proceed with the installation. Contact the IEI reseller or

vendor you purchased the ITG-100AI

representative directly. To contact an IEI sales representative, please

send an email to sales@iei.com.tw.

The ITG-100AI is shipped with the following components:

Quantity Item and Part Number Image

1 ITG-100AI

Page 19

ITG-100AI Embedded System

Page 9

Quantity Item and Part Number Image

1 Adapter

(P/N: 63040-010036-210-RS)

1 Power cord

1 Power cable

(P/N: 32102-045700-100-RS)

1 1 x RJ-45 to DB-9 COM port cable

1 Mounting Bracket

3 Screws (M3*6) for DIN mount

Table 2-1: Package List Contents

Page 20

ITG-100AI Embedded System

Page 10

Chapter

3 Installation

Page 21

ITG-100AI Embedded System

Page 11

3.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the maintenance of the ITG-100AI

may result in permanent damage to the ITG-100AI and severe injury to the

user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the WAFER series motherboard and the power module. (Dry climates are

especially susceptible to ESD.) It is therefore critical that whenever the ITG-100AI is

opened and any electrical component handled, the following anti-static precautions are

strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

 Self-grounding: Before handling the board, touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

 Use an anti-static pad: When configuring the ITG-100AI, place it on an

anti-static pad. This reduces the possibility of ESD damaging the ITG-100AI.

3.2 Installation Precautions

During installation, be aware of the precautions below:

 Read the user manual: The user manual provides a complete description of

the ITG-100AI, installation instructions and configuration options.

 DANGER! Disconnect Power: Power to the ITG-100AI must be

disconnected during the installation process, or before any attempt is made to

access the rear panel. Electric shock and personal injury might occur if the

rear panel of the ITG-100AI is opened while the power cord is still connected

to an electrical outlet.

Page 22

ITG-100AI Embedded System

Page 12

 Qualified Personnel: The ITG-100AI must be installed and operated only by

trained and qualified personnel. Maintenance, upgrades, or repairs may only

be carried out by qualified personnel who are familiar with the associated

dangers.

 Air Circulation: Make sure there is sufficient air circulation when installing

the ITG-100AI. The ITG-100AI’s cooling vents must not be obstructed by any

objects. Blocking the vents can cause overheating of the ITG-100AI. Leave at

least 5 cm of clearance around the ITG-100AI to prevent overheating.

 Grounding: The ITG-100AI should be properly grounded. The voltage feeds

must not be overloaded. Adjust the cabling and provide external overcharge

protection per the electrical values indicated on the label attached to the back

of the ITG-100AI.

3.3 Bottom Cover Removal and Re-installation

Before installing or maintaining the internal components, the bottom cover must be

removed from the ITG-100AI. Follow the steps below to complete the task.

Step 1: Remove the bottom panel by removing the four retention screws from the

bottom cover (Figure 3-1).

Figure 3-1: Bottom Cover Retention Screws

Step 2: Gently lift the cover to remove it.

Page 23

ITG-100AI Embedded System

Page 13

Step 3: To re-install the bottom cover, orient the bottom cover to make the metal piece

inside the cover position on the top of the PCIe accelerator card for heat

dissipation (Figure 3-2).

Figure 3-2: Bottom Cover Installation

Step 4: Fasten the four retention screws previously remove to secure the bottom cover.

3.4 SO-DIMM Installation

WARNING:

Using incorrectly specified SO-DIMM may cause permanently damage

the ITG-100AI. Please make sure the purchased SO-DIMM complies

with the memory specifications of the ITG-100AI.

To install a SO-DIMM into a SO-DIMM socket, please follow the steps below.

Step 1: Remove the bottom cover from the ITG-100AI. Please follow the instruction

described in Section 3.3.

Step 2: Locate the SO-DIMM socket on the motherboard (Figure 3-3).

Page 24

ITG-100AI Embedded System

Page 14

Figure 3-3: SO-DIMM Socket

Step 3: Align the SO-DIMM with the socket. The SO-DIMM must be oriented in such a

way that the notch in the middle of the SO-DIMM must be aligned with the

plastic bridge in the socket (Figure 3-4).

Step 4: Push the SO-DIMM into the socket at an angle (Figure 3-4).

Figure 3-4: SO-DIMM Installation

Step 5: Gently pull the arms of the SO-DIMM socket out and push the rear of the

SO-DIMM down (Figure 3-4).

Step 6: Release the arms on the SO-DIMM socket. They clip into place and secure the

SO-DIMM in the socket.

Step 7: Install the bracket that was previously removed in the same position it was

before.

Page 25

ITG-100AI Embedded System

Page 15

Step 8: Reinstall the bottom panel to the ITG-100AI by following the instruction

described in Section 3.3.

3.5 Wireless LAN Module Installation (Optional)

The ITG-100AI has an M.2 slot for WLAN card installation. The M.2 card slot is located

under the accelerator card. To install the optional wireless LAN (WLAN) module, please

follow the steps below.

Step 1: Remove the bottom cover from the ITG-100AI. Please follow the instruction

described in Section 3.3.

Step 2: Remove the accelerator card by removing the two retention screws as shown

below.

Figure 3-5: Accelerator Card Retention Screws

Step 3: Locate the M.2 card slot (Figure 3-6).

Page 26

ITG-100AI Embedded System

Page 16

Figure 3-6: WLAN M.2 Card Slot Location

Step 4: Line up the notch on the module with the notch on the slot. Slide the WLAN card

into the socket at an angle of about 20º (Figure 3-7).

Figure 3-7: Inserting the WLAN Card into the Slot at an Angle

Step 5: Secure the WLAN card with an M2*3 retention screw (Figure 3-8).

Page 27

ITG-100AI Embedded System

Page 17

Figure 3-8: Securing the WLAN Card

3.6 RS-232/422/485 Serial Port Connection

The ITG-100AI has two RS-232/422/485 serial port connectors on the bottom panel. One

is DB-9 connector and the other is RJ-45 connector.

3.6.1 DB-9 RS-232/422/485 Serial Port Connection

DB-9 RS-232/422/485 serial port devices can be attached to the DB-9 port on the bottom

panel.

Step 1: Locate the DB-9 connector. The locations of the DB-9 connector are shown in

Figure 1-3.

Step 2: Insert the serial connector. Insert the DB-9 connector of a serial device into

the DB-9 connector on the external peripheral interface. See Figure 3-9.

Page 28

ITG-100AI Embedded System

Page 18

Figure 3-9: Serial Device Connector

Step 3: Secure the connector. Secure the serial device connector to the external

interface by tightening the two retention screws on either side of the connector.

Figure 3-10: DB-9 RS-232/422/485 Serial Port Connector

3.6.2 RJ-45 RS-232/422/485 Serial Port Connection

The RJ-45 RS-232/422/485 serial port connects to a cable with a standard DB-9

connector at the other end (cables included). Follow the steps below to connect a serial

device to the ITG-100AI.

Step 1: Locate the RJ-45 connector. The location of the RJ-45 serial port connector is

shown in Chapter 2. The RJ-45 connectors for the serial ports can be identified

easily as the RJ-45 for the network has two LEDs on the port, while the

connectors for the serial cables don’t.

Page 29

ITG-100AI Embedded System

Page 19

Step 2: Insert the RJ-45 to DB-9 cable.

Step 3: Insert the serial connector. Insert the DB-9 connector of a serial device into

the DB-9 connector on the cable. See Figure 3-11.

Figure 3-11: Serial Device Connector

Step 4: Secure the connector. Secure the serial device connector to the external

interface by tightening the two retention screws on either side of the connector.

Figure 3-12: RJ-45 RS-232/422/485 Serial Port Connector

Pin RS-232 RS-422 RS-485

1 NDCD1 TX- DATA-

2 NDSR1

3 NRX1 TX+ DATA+

4 NRTS1

5 NTX1 RX+

6 NCTS1

7 NDTR1 RX-

8 NRI1

Table 3-1: RJ-45 RS-232/422/485 Serial Port Pinouts

Page 30

ITG-100AI Embedded System

Page 20

Figure 3-13: DB-9 RS-232/422/485 Connector Pinout Location

Pin RS-232 RS-422 RS-485

NDCD TX- DATA-

NRX TX+ DATA+

NTX RX+

NDTR RX-

GND

NDSR

NRTS

NCTS

NRI

Table 3-2: DB-9 RS-232/422/485 Connector Pinouts

NOTE:

The communication protocol of the serial ports is set through the BIOS menu in “Advanced  F81866 Super IO Configuration  Serial Port 1/2 Configuration”. Use the Device Mode BIOS option to configure the correspondent serial ports (refer to Sections 4.3.2.1.1 and 4.3.2.1.2 for detailed information).

Page 31

ITG-100AI Embedded System

Page 21

3.7 AT/ATX Mode Selection

AT or ATX power mode can be used on the ITG-100AI. The selection is made through an

AT/ATX switch located on the front panel (Figure 3-14). To select AT mode or ATX mode,

follow the steps below.

Step 1: Locate the AT/ATX switch on the front panel (Figure 3-14).

Figure 3-14: AT/ATX Switch Location

Step 2: Adjust the AT/ATX switch. Step 0:

3.7.1 AT Power Mode

With the AT mode selected, the power is controlled by a central power unit rather than a

power switch. The ITG-100AI panel PC turns on automatically when the power is

connected. The AT mode benefits a production line to control multiple panel PCs from a

central management center and other applications including:

 ATM

 Self-service kiosk

 Plant environment monitoring system

 Factory automation platform

 Manufacturing shop flow

Page 32

ITG-100AI Embedded System

Page 22

3.7.2 ATX Power Mode

With the ATX mode selected, the ITG-100AI panel PC goes in a standby mode when it is

turned off. The panel PC can be easily turned on via network or a power switch in standby

mode. Remote power control is perfect for advertising applications since the broadcasting

time for each panel PC can be set individually and controlled remotely. Other possible

application includes:

 Security surveillance

 Point-of-Sale (POS)

 Advertising terminal

3.8 Mounting the System

To mount the ITG-100AI embedded system onto a DIN rail, please follow the steps below.

Step 1: Attach the DIN mount bracket to the rear panel of the ITG-100AI. Secure the

bracket to the ITG-100AI with three supplied retention screws (Figure 3-15).

WARNING:

When installing the DIN mount bracket onto the ITG-100AI, pay special

attention to the direction of the DIN rail mount bracket. See Figure 3-15.

Page 33

ITG-100AI Embedded System

Page 23

Figure 3-15: Mounting the DIN Rail

Step 2: Place the DIN rail against the back of the DIN mount bracket making sure the

edges of the DIN rail are between the clamps of the DIN mount bracket

(Figure 3-16).

Figure 3-16: Mounting to DIN Rail

Page 34

ITG-100AI Embedded System

Page 24

3.9 Powering On/Off the System

 Power on the system: press the power button for 3 seconds

 Power off the system: press the power button for 6 seconds

Figure 3-17: Power Button Location

3.10 Reset the System

The reset button enables user to reboot the system when the system is turned on. To

reboot the system, follow the steps below.

Step 3: Locate the reset button on the front panel (Figure 3-18).

Figure 3-18: Reset Button Location

Step 4: Press the reset button. Step 0:

Page 35

ITG-100AI Embedded System

Page 25

Chapter

4 BIOS

Page 36

ITG-100AI Embedded System

Page 26

Some of the BIOS options may vary throughout the life cycle of the

4.1 Introduction

The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to

certain system settings. This chapter outlines the options that can be changed.

NOTE:

product and are subject to change without prior notice.

4.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be

activated in one of two ways.

1. Press the D

2. Press the D

appears on the screen. 0.

If the message disappears before the D

and try again.

ELETE or F2 key as soon as the system is turned on or

ELETE or F2 key when the “Press Del to enter SETUP” message

ELETE or F2 key is pressed, restart the computer

4.1.2 Using Setup

Use the arrow keys to highlight items, press ENTER to select, use the PageUp and

PageDown keys to change entries, press F1 for help and press E

keys are shown in.

Key Function

Up arrow Move to previous item

Down arrow Move to next item

SC to quit. Navigation

Left arrow Move to the item on the left hand side

Right arrow Move to the item on the right hand side

+ Increase the numeric value or make changes

Page 37

ITG-100AI Embedded System

Page 27

Key Function

- Decrease the numeric value or make changes

F1 key General help, only for Status Page Setup Menu and Option

Page Setup Menu

F2 key Load previous values.

F3 key Load optimized defaults

F4 key Save changes and Exit BIOS

Esc key Main Menu – Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --

Exit current page and return to Main Menu

Table 4-1: BIOS Navigation Keys

4.1.3 Getting Help

When F1 is pressed a small help window describing the appropriate keys to use and the

possible selections for the highlighted item appears. To exit the Help Window press E

the F1 key again.

4.1.4 Unable to Reboot after Configuration Changes

If the computer cannot boot after changes to the system configuration is made, CMOS

defaults. Use the jumper described in Chapter 3.

4.1.5 BIOS Menu Bar

The menu bar on top of the BIOS screen has the following main items:

 Main – Changes the basic system configuration.

 Advanced – Changes the advanced system settings.

 Chipset – Changes the chipset settings.

 Security – Sets User and Supervisor Passwords.

SC or

 Boot – Changes the system boot configuration.

 Save & Exit – Selects exit options and loads default settings

Page 38

ITG-100AI Embedded System

Page 28

Main

Advanced

Chipset

Security

Boot

Save & Exit

The following sections completely describe the configuration options found in the menu

items at the top of the BIOS screen and listed above.

4.2 Main

The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.

The Main menu gives an overview of the basic system information.

BIOS Information BIOS Vendor American Megatrends Core Version 5.12 Compliency UEFI 2.5; PI 1.4 Project Version SJ45AR10.BIN

Build Date and Time

iWDD Vendor iEi iWDD Version SAL3ER01.bin

Platform firmware Information BXT SOC F1 MRC Version 0.56 PUNIT FW 1A PMC FW 03.20 TXE FW 3.1.65.2288 GOP 0.0.0036 CPU Flavor BXT Notebook/Desktop (1) Board ID Oxbow Hill CRB (06) Fab ID FAB A

Memory Information Total Memory 8192 MB Memory Speed 1866 MHz

System Date [Fri 08/23/2019] System Time [15:43:27]

Access Level Administrator

/16/2019 08:36:12

Set the Date. Use Tab to switch between Data elements. Default Ranges: Year: 2005-2099 Months: 1-12 Days: dependent on month

--------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

BIOS Menu 1: Main

The System Overview field also has two user configurable fields:

Page 39

ITG-100AI Embedded System

Page 29

Main

Advanced

Chipset

Security

Boot

Save & Exit

 System Date [xx/xx/xx]

Use the System Date option to set the system date. Manually enter the day, month and

year.

 System Time [xx:xx:xx]

Use the System Time option to set the system time. Manually enter the hours, minutes

and seconds.

4.3 Advanced

Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices

through the following sub-menus:

WARNING!

Setting the wrong values in the sections below may cause the system

to malfunction. Make sure that the settings made are compatible with

the hardware.

> ACPI Settings > F81866 Super IO Configuration > Hardware Monitor > RTC Wake Settings > Serial Port Console Redirection > CPU Configuration > USB Configuration > iEi Feature > SATA Configuration

System ACPI Parameters.

----------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

BIOS Menu 2: Advanced

Page 40

ITG-100AI Embedded System

Page 30

Advanced

(Suspend to

off. Power to the RAM is maintained. The

computer returns slower to a working state, but

4.3.1 ACPI Settings

The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and

Power Interface (ACPI) options.

ACPI Settings

ACPI Sleep State [S3 (Suspend to RAM]

BIOS Menu 3: ACPI Configuration

 ACPI Sleep State [S3 only (Suspend to RAM)]

The fields in ACPI Sleep State option cannot be changed.



EFAULT

The caches are flushed and the CPU is powered

----------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

RAM)

more power is saved.

Page 41

ITG-100AI Embedded System

Page 31

Advanced

ESC Exit

4.3.2 F81866 Super IO Configuration

Use the F81866 Super IO Configuration menu (BIOS Menu 10) to set or change the

configurations for the serial ports.

F81866 Super IO Configuration

Super IO Chip F81866

> Serial Port 1 Configuration > Serial Port 2 Configuration > Serial Port 3 Configuration > Serial Port 4 Configuration

BIOS Menu 4: Super IO Configuration

4.3.2.1 Serial Port n Configuration

Use the Serial Port n Configuration menu (BIOS Menu 5) to configure the serial port n.

Set Parameters of Serial Port 1 (COMA)

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

Serial Port 1 Configuration

Serial Port [Enabled]

Device Settings IO=3F8h; IRQ=4

Device Mode [RS232]

BIOS Menu 5: Serial Port 1 Configuration Menu

Enable or Disable Serial Port (COM)

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

Page 42

ITG-100AI Embedded System

Page 32

4.3.2.1.1 Serial Port 1 Configuration

 Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.



Disabled



Enabled DEFAULT

 Device Mode [RS232]

Use the Device Mode option to select the serial port mode.



RS232 DEFAULT



RS422



RS485

4.3.2.1.2 Serial Port 2 Configuration

 Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disable the serial port

Enable the serial port

Enables serial port RS-232 support.

Enables serial port RS-422 support.

Enables serial port RS-485 support.



Disabled



Enabled DEFAULT

 Device Mode [RS232]

Use the Device Mode option to select the serial port mode.



RS232 DEFAULT



RS422



RS485

Disable the serial port

Enable the serial port

Enables serial port RS-232 support.

Enables serial port RS-422 support.

Enables serial port RS-485 support.

Page 43

ITG-100AI Embedded System

Page 33

4.3.2.1.3 Serial Port 3 Configuration

 Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.



Disabled



Enabled DEFAULT

4.3.2.1.4 Serial Port 4 Configuration

 Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.



Disabled



Enabled DEFAULT

4.3.3 Hardware Monitor

The Hardware Monitor menu (BIOS Menu 6) contains the fan configuration submenus

and displays operating temperature, fan speeds and system voltages.

Disable the serial port

Enable the serial port

Disable the serial port

Enable the serial port

Page 44

ITG-100AI Embedded System

Page 34

Advanced

ESC Exit

PC Health Status

CPU temperature :+39 °C SYS temperature :+41 °C VSCC_SVID :+0.832 V V5_S :+5.003 V V12_S :+12.056 V V3P3_S :+3.296 V

BIOS Menu 6: Hardware Monitor

 PC Health Status

The following system parameters and values are shown. The system parameters that are

monitored are:

---------------------



: Select Screen

↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit

 Temperatures:

o CPU Temperature o System temperature

 Voltages:

o VSCC_SVID o V5_S o V12_S o V3P3_S

4.3.4 RTC Wake Settings

The RTC Wake Settings menu (BIOS Menu 8) configures RTC wake event.

Page 45

ITG-100AI Embedded System

Page 35

Advanced

ESC Exit

The real time clock (RTC) cannot generate a wake

every day at the specified time. Besides, the

values that can be

RTC Wake Settings

Wake system with Fixed Time [Disabled]

BIOS Menu 7: RTC Wake Settings

 Wake system with Fixed Time [Disabled]

Use the Wake system with Fixed Time option to enable or disable the system wake on

Enable or disable System wake on alarm event. When enabled, System will wake on the date::hr::min::sec specified

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

alarm event.



Disabled D



Enabled

EFAULT

event

If selected, the Wake up every day option appears

allowing you to enable to disable the system to wake

following options appear with

selected:

Wake up date

Wake up hour

Wake up minute

Wake up second

After setting the alarm, the computer turns itself on

from a suspend state when the alarm goes off.

Page 46

ITG-100AI Embedded System

Page 36

Advanced

4.3.5 Serial Port Console Redirection

The Serial Port Console Redirection menu (BIOS Menu 8) allows the console

redirection options to be configured. Console redirection allows users to maintain a

system remotely by re-directing keyboard input and text output through the serial port.

COM1

Console Redirection [Disabled]

> Console Redirection Settings

COM2

Console Redirection [Disabled]

> Console Redirection Settings

COM3

Console Redirection [Disabled]

> Console Redirection Settings

COM4

Console Redirection [Disabled]

> Console Redirection Settings

BIOS Menu 8: Serial Port Console Redirection

 Console Redirection [Disabled]

Use Console Redirection option to enable or disable the console redirection function.

Console Redirection Enable or Disable

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit



Disabled DE FAU LT



Enabled

4.3.5.1 Console Redirection Settings

The Console Redirection Settings menu (BIOS Menu 9) allows the console redirection

options to be configured. The option is active when Console Redirection option is enabled.

Disabled the console redirection function

Enabled the console redirection function

Page 47

ITG-100AI Embedded System

Page 37

Advanced

support color, function

Unicode chars onto 1 or

COM1 Console Redirection Settings

Terminal Type [ANSI] Bits per second [115200] Data Bits [8] Parity [None] Stop Bits [1]

BIOS Menu 9: Console Redirection Settings

Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to

keys, etc. VT-UTF8: Uses UTF8 encoding to map

more bytes.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

 Terminal Type [ANSI]

Use the Terminal Type option to specify the remote terminal type.

 Bits per second [115200]

Use the Bits per second option to specify the serial port transmission speed. The speed

must match the other side. Long or noisy lines may require lower speeds.



VT100



VT100+



VT-UTF8



ANSI DEFA ULT



9600



19200

The target terminal type is VT100

The target terminal type is VT100+

The target terminal type is VT-UTF8

The target terminal type is ANSI

Sets the serial port transmission speed at 9600.

Sets the serial port transmission speed at 19200.

Page 48

ITG-100AI Embedded System

Page 38

This option does not



38400



57600



115200 DE FAU LT

 Data Bits [8]

Use the Data Bits option to specify the number of data bits.



8 DEFAULT

 Parity [None]

Use the Parity option to specify the parity bit that can be sent with the data bits for

detecting the transmission errors.



None DEFAULT

Sets the serial port transmission speed at 38400.

Sets the serial port transmission speed at 57600.

Sets the serial port transmission speed at 115200.

Sets the data bits at 7.

Sets the data bits at 8.

No parity bit is sent with the data bits.



Even



Odd



Mark



Space

 Stop Bits [1]

Use the Stop Bits option to specify the number of stop bits used to indicate the end of a

serial data packet. Communication with slow devices may require more than 1 stop bit.



1 DEFAULT



The parity bit is 0 if the number of ones in the data

bits is even.

The parity bit is 0 if the number of ones in the data

bits is odd.

The parity bit is always 1.

provide error detection.

The parity bit is always 0.

provide error detection.

Sets the number of stop bits at 1.

Sets the number of stop bits at 2.

Page 49

ITG-100AI Embedded System

Page 39

Advanced

C-States [Disabled]

When enabled, a VMM can

ESC Exit

4.3.6 CPU Configuration

Use the CPU Configuration menu (BIOS Menu 10) to view detailed CPU specifications

and configure the CPU.

CPU Configuration

Intel(R) Atom(TM) Processor E3930 @ 1.30GHz CPU Signature 506C9 Microcode Patch 2E Max CPU Speed 1300 MHz Min CPU Speed 800 MHz Processor Cores 2 Intel HT Technology Not Supported Intel VT-x Technology Supported Intel SMX Technology Not Supported

L1 Data Cache 24 KB x 2 L1 Code Cache 32 KB x 2 L2 Cache 1024 KB x 2 L3 Cache Not Present Speed 1300 MHz 64-bit Supported

Intel Virtualization Technology [Disabled] EIST [Enabled]

utilize the additional hardware capabilities provided by Vanderpool Technology.

----------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

 Intel® Virtualization Technology [Disabled]

Use the Intel® Virtualization Technology option to enable or disable virtualization on the

system. When combined with third party software, Intel Virtualization technology allows

several OSs to run on the same system at the same time.

 EIST [Enabled]

Use the EIST option to enable or disable the Intel Speed Step Technology.

BIOS Menu 10: CPU Configuration



Disabled DEFAULT



Enabled

Disables Intel Virtualization Technology.

Enables Intel Virtualization Technology.

Page 50

ITG-100AI Embedded System

Page 40

Advanced

disables legacy support

ESC Exit



Disabled



Enabled DEFAULT

 C-States [Disabled]

Use the C-States option to enable or disable the CPU C state.



Disabled DEFAULT



Enabled

Disables the Intel Speed Step Technology.

Enables the Intel Speed Step Technology.

Disables the CPU C state.

Enables the CPU C state.

4.3.7 USB Configuration

Use the USB Configuration menu (BIOS Menu 11) to read USB configuration

information and configure the USB settings.

USB Configuration

USB Devices: 1 Keyboard

Legacy USB Support [Enabled]

Enables Legacy USB support. AUTO option

if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

 USB Devices

The USB Devices Enabled field lists the USB devices that are enabled on the system

BIOS Menu 11: USB Configuration

Page 51

ITG-100AI Embedded System

Page 41

Advanced

crashes. Please install

service before enabling

ESC: Exit

 Legacy USB Support [Enabled]

Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

keyboard can control the system even when there is no USB driver loaded onto the

system.



Enabled DEFAULT



Disabled

Legacy USB support enabled

Legacy USB support disabled

4.3.8 iEi Feature

Use the iEi Feature menu (BIOS Menu 12) to configure the iEi features.

iEi Feature

Auto Recovery Function [Disabled]

Auto Recovery Function Reboot and recover system automatically within 10 min, when OS

Auto Recovery API

this function.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit

BIOS Menu 12: iEi Feature

 Auto Recovery Function [Disabled]

Use Auto Recovery Function option to enable or disable the auto recovery function.

Page 52

ITG-100AI Embedded System

Page 42

Advanced

ESC Exit



Disabled DE FAU LT



Enabled

Disabled the auto recovery function

Enabled the auto recovery function

4.3.9 SATA Configuration

Use the SATA Configuration menu (BIOS Menu 13) to change and/or set the

configuration of the SATA devices installed in the system.

SATA Configuration

SATA Mode Selection [ACHI]

SATA Port0 SATADOM-SH 3ME (32.0GB)

Hot Plug [Disabled]

mSATA Port Not Present

Hot Plug [Disabled]

Determines how SATA controller(s) operate.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

BIOS Menu 13: IDE Configuration

 SATA Mode Selection [AHCI]

Use the SATA Mode Selection option to configure SATA devices as normal IDE devices.



AHCI DEFAULT

 Hot Plug [Disabled]

Use the Hot Plug option to configure the port as Hot Pluggable.



Disabled DEFAU LT



Enabled

Configures SATA devices as AHCI device.

Disables the port as Hot Pluggable.

Enables the port as Hot Pluggable.

Page 53

ITG-100AI Embedded System

Page 43

Main

Advanced

Chipset

Security

Boot

Save & Exit

ESC Exit

4.4 Chipset

Use the Chipset menu (BIOS Menu 14) to access the Northbridge and Southbridge

configuration menus

WARNING!

Setting the wrong values for the Chipset BIOS selections in the Chipset

BIOS menu may cause the system to malfunction.

> North Bridge > South Bridge

BIOS Menu 14: Chipset

North Bridge Parameters

---------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit

Page 54

ITG-100AI Embedded System

Page 44

Chipset

ESC: Exit

4.4.1 North Bridge Configuration

Use the North Bridge Configuration menu (BIOS Menu 15) to configure the Intel IGD

settings.

Memory Information

Total Memory 8192 MB(DDR3L)

Memory Slot0 8192 MB(DDR3L)

> Intel IGD Configuration

BIOS Menu 15: Northbridge Chipset Configuration

 Memory Information

The Memory Information lists a brief summary of the on-board memory. The fields in

Memory Information cannot be changed.

Intel IGD Configuration

---------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit

4.4.1.1 Intel IGD Configuration

Use the Intel IGD Configuration menu (BIOS Menu 16) to configure the video device

connected to the system.

Page 55

ITG-100AI Embedded System

Page 45

Chipset

ESC: Exit

Intel IGD Configuration

Primary Display [IGD] DVMT Pre-Allocated [256M] DVMT Total Gfx Mem [Max]

BIOS Menu 16: Integrated Graphics

 Primary Display [IGD]

Use the Primary Display option to select the primary graphics controller the system uses.

The following options are available:

Select which of IGD/PCI Graphics device should be Primary Display.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit

 IGD Default

 PCIe

 DVMT Pre-Allocated [256MB]

Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the

integrated graphics processor when the system boots. The system memory allocated can

then only be used as graphics memory, and is no longer available to applications or the

operating system. Configuration options are listed below:

 64M

 128M

 256M Default

 512M

Page 56

ITG-100AI Embedded System

Page 46

Chipset

should be when restoring

ESC: Exit

 DVMT Total Gfx Mem [Max]

Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used

by the internal graphic device. The following options are available:

 128M

 256M

 Max Default

4.4.2 Southbridge Configuration

Use the Southbridge Configuration menu (BIOS Menu 17) to configure the Southbridge

chipset.

Auto Power Button Status [Enabled(ATX)]

Restore AC Power Loss [Last State] Power Saving Function(ERP) [Disabled]

OS Selection [Windows] > PCI Express Configuration > SCC Configuration

BIOS Menu 17: Southbridge Chipset Configuration

 Restore AC Power Loss [Last State]

Use the Restore on AC Power Loss option to specify what state the system returns to if

there is a sudden loss of power to the system.



Power Off

The system remains turned off

Select the state system

on AC Power Loss.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit



Power On

Last State DEFAULT

The system turns on

The system returns to its previous state. If it was on, it

turns itself on. If it was off, it remains off.

Page 57

ITG-100AI Embedded System

Page 47

Chipset

ESC: Exit

 Power Saving Function (EUP) [Disabled]

Use the Power Saving Function (EUP) option to enable or disable the power saving

function.



Disabled DEFAULT



Enabled

 OS Selection [Windows]

Use the OS Selection BIOS option to select the OS. Configuration options are listed below.

 Windows

 Android

DEFA ULT

Power saving function is disabled.

Power saving function is enabled. It will reduce power

consumption when the system is off.

4.4.2.1 PCI Express Configuration

Use the PCI Express Configuration menu (BIOS Menu 18) to select the support type of

the PCIe Mini slot.

PCI Express Configuration

Compliance Mode [Disabled] > M.2 > mPCIE

BIOS Menu 18: PCI Express Configuration

 Compliance Mode [Disabled]

Use the Compliance Mode option to enable or disable the compliance mode.

Compliance Mode Enable/Disable.

----------------------



: Select Screen

↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit

Page 58

ITG-100AI Embedded System

Page 48

Chipset

ESC: Exit



Disabled DEFAU LT



Enabled

The M.2 and mPCIE submenus all contain the following options:

 PCIe Speed [Auto]

Use PCIe Speed option to select the speed type of the PCIe Mini slot. The following

options are available:

 Auto Default

 Gen1

 Gen2

Disables the compliance mode.

Enables the compliance mode.

4.4.2.2 SCC Configuration

Use the SCC Configuration menu (BIOS Menu 19) to configure the SCC settings.

SCC SD Card Support (D27:F0) [Enabled] SCC eMMC Support (D28:F0) [Enabled] eMMC Max Speed [HS400]

BIOS Menu 19: PCI Express Configuration

 SCC SD Card Support [Enabled]

Use the SCC SD Card Support option to enable or disable the SCC SD card support.



Disabled

Disables the SCC SD card support.

Enable/Disable SCC SD Card Support.

----------------------



: Select Screen

↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit

Page 59

ITG-100AI Embedded System

Page 49

Main

Advanced

Chipset

Security

Boot

Save & Exit

Set Setup Administrator



Enabled DEFAULT

 SCC eMMC Support [Enabled]

Use the SCC eMMC Support option to enable or disable the SCC eMMC support.



Disabled



Enabled DEFAULT

 eMMC Max Speed [HS400]

Use eMMC Max Speed option to select the eMMC max speed. The following options are

available:

 HS400 Default

 HS200

 DDR50

Enables the SCC SD card support.

Disables the SCC eMMC support.

Enables the SCC eMMC support.

4.5 Security

Use the Security menu (BIOS Menu 20) to set system and user passwords.

Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights. The password length must be: Minimum length 3 Maximum length 20

Administrator Password User Password

BIOS Menu 20: Security

Password

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit

Page 60

ITG-100AI Embedded System

Page 50

Main

Advanced

Chipset

Security

Boot

Save & Exit

ESC Exit

Allows the Number Lock on the keyboard to be

enabled automatically when the computer system

boots up. This allows the immediate use of the

the keyboard. To confirm this, the Number Lock LED

 Administrator Password

Use the Administrator Password to set or change a administrator password.

 User Password

Use the User Password to set or change a user password.

4.6 Boot

Use the Boot menu (BIOS Menu 19) to configure system boot options.

Boot Configuration

Bootup NumLock State [On] Quiet Boot [Enabled] Launch PXE OpROM [Disabled] Option ROM Messages [Force BIOS] UEFI Boot [Disabled]

Boot Option Priorities

Boot Option #1 [P0: SATADOM-SH SME 4]

Hard Drive BBS Priorities

BIOS Menu 21: Boot

 Bootup NumLock State [On]

Use the Bootup NumLock State BIOS option to specify if the number lock setting must

be modified during boot up.

Select the keyboard NumLock state

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save



On DEFAULT

10-key numeric keypad located on the right side of

light on the keyboard is lit.

Page 61

ITG-100AI Embedded System

Page 51

Does not enable the keyboard Number Lock

the upper

key pad. The Number

Lock LED on the keyboard lights up when the



Off

 Quiet Boot [Enabled]

Use the Quiet Boot BIOS option to select the screen display when the system boots.

automatically. To use the 10-keys on the keyboard,

press the Number Lock key located on

left-hand corner of the 10-

Number Lock is engaged.



Disabled



Enabled DEFAULT

 Launch PXE OpROM [Disabled]

Use the Launch PXE OpROM option to enable or disable boot option for legacy network

devices.



Disabled DE FAU LT



Enabled

 Option ROM Messages [Force BIOS]

Use the Option ROM Messages option to set the Option ROM display mode.



Force

BIOS

DEFAULT

Normal POST messages displayed

OEM Logo displayed instead of POST messages

Ignore all PXE Option ROMs

Load PXE Option ROMs.

Sets display mode to force BIOS.



Keep

Current

 UEFI Boot [Disabled]

Use the UEFI Boot option to enable or disable to boot from the UEFI devices.



Enabled

Sets display mode to current.

Boot from UEFI devices is enabled.

Page 62

ITG-100AI Embedded System

Page 52

Main

Advanced

Chipset

Security

Boot

Save & Exit

ESC Exit



Disabled DE FAU LT

 Boot Option Priority

Use the Boot Option Priority function to set the system boot sequence from the available

devices. The drive sequence also depends on the boot sequence in the individual device

section.

 Hard Drive BBS Priorities

Use the Hard Drive BBS Priorities option to set the order of the legacy devices in this

group.

4.7 Exit

Use the Exit menu (BIOS Menu 22) to load default BIOS values, optimal failsafe values

and to save configuration changes.

Boot from UEFI devices is disabled.

Save Changes and Reset Discard Changes and Reset

Restore Defaults Save as User Defaults Restore User Defaults

BIOS Menu 22:Exit

Reset the system after saving the changes.

---------------------



: Select Screen

↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save

Page 63

ITG-100AI Embedded System

Page 53

 Save Changes and Reset

Use the Save Changes and Reset option to save the changes made to the BIOS options

and to exit the BIOS configuration setup program.

 Discard Changes and Reset

Use the Discard Changes and Reset option to exit the system without saving the

changes made to the BIOS configuration setup program.

 Restore Defaults

Use the Restore Defaults option to load the optimal default values for each of the

parameters on the Setup menus. F3 key can be used for this operation.

 Save as User Defaults

Use the Save as User Defaults option to save the changes done so far as user defaults.

 Restore User Defaults

Use the Restore User Defaults option to restore the user defaults to all the setup options.

Page 64

ITG-100AI Embedded System

Page 54

Chapter

5 Software Installation

Page 65

ITG-100AI Embedded System

Page 55

5.1 Available Drivers

All the drivers for the ITG-100AI are available on IEI Resource Download Center

(https://download.ieiworld.com). Type ITG-100AI and press Enter to find all the relevant

software, utilities, and documentation.

Figure 5-1: IEI Resource Download Center

5.1.1 Driver Download

To download drivers from IEI Resource Download Center, follow the steps below.

Step 1: Go to https://download.ieiworld.com. Type ITG-100AI and press Enter.

Step 2: All product-related software, utilities, and documentation will be listed. You can

choose Driver to filter the result.

Page 66

ITG-100AI Embedded System

Page 56

Step 3: Click the driver file name on the page and you will be prompted with the

following window. You can download the entire ISO file (

arrow to find an individual driver and click the file name to download (

), or click the small

).

NOTE:

To install software from the downloaded ISO image file in Windows 8,

8.1 or 10, double-click the ISO file to mount it as a virtual drive to view

its content. On Windows 7 system, an additional tool (such as Virtual

CD-ROM Control Panel from Microsoft) is needed to mount the file.

Page 67

ITG-100AI Embedded System

Page 57

5.2 OpenVINO™ Toolkit Installation

To install OpenVINO™ Toolkit via website, follow the steps below.

Step 1: Go to https://software.intel.com/en-us/openvino-toolkit.

Step 2: Click "Get Started" then choose your configuration from "Development

Environment Installation Guides".

Step 3: Follow the instruction to complete the installation procedure.

Page 68

ITG-100AI Embedded System

Page 58

Appendix

A Regulatory Compliance

Page 69

ITG-100AI Embedded System

Page 59

f the user modifies and/or install other devices in the equipment, the CE conformity

has telecommunications functionality, it also complies with the

2014/53/EU

IEI Integration Corp erklærer herved, at følgende udstyr overholder de væsentlige krav o

DECLARATION OF CONFORMITY

This equipment is in conformity with the following EU directives:

 EMC Directive (2014/30/EU)

 Low-Voltage Directive (2014/35/EU)

 RoHS II Directive (2011/65/EU, 2015/863/EU)

declaration may no longer apply.

If this equipment

requirements of the Radio Equipment Directive 2014/53/EU.

English

IEI Integration Corp declares that this equipment is in compliance with the essential

requirements and other relevant provisions of Directive 2014/53/EU.

Български [Bulgarian]

IEI Integration Corp. декларира, че този оборудване е в съответствие със

съществените изисквания и другите приложими правила на Директива

Česky [Czech]

IEI Integration Corp tímto prohlašuje, že tento zařízení je ve shodě se základními

požadavky a dalšími příslušnými ustanoveními směrnice 2014/53/EU.

Dansk [Danish]

øvrige relevante krav i direktiv 2014/53/EU.

Deutsch [German]

IEI Integration Corp, erklärt dieses Gerät entspricht den grundlegenden Anforderungen

und den weiteren entsprechenden Vorgaben der Richtlinie 2014/53/EU.

Page 70

ITG-100AI Embedded System

Page 60

Eesti [Estonian]

IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 2014/53/EÜ

põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Español [Spanish]

IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y

cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU.

Ελληνική [Greek]

IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ

ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ

2014/53/EU.

Français [French]

IEI Integration Corp déclare que l'appareil est conforme aux exigences essentielles et aux

autres dispositions pertinentes de la directive 2014/53/EU.

Italiano [Italian]

IEI Integration Corp dichiara che questo apparecchio è conforme ai requisiti essenziali ed

alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53/EU.

Latviski [Latvian]

IEI Integration Corp deklarē, ka iekārta atbilst būtiskajām prasībām un citiem ar to

saistītajiem noteikumiem Direktīvas 2014/53/EU.

Lietuvių [Lithuanian]

IEI Integration Corp deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas

2014/53/EU Direktyvos nuostatas.

Nederlands [Dutch]

IEI Integration Corp dat het toestel toestel in overeenstemming is met de essentiële eisen

en de andere relevante bepalingen van richtlijn 2014/53/EU.

Malti [Maltese]

IEI Integration Corp jiddikjara li dan prodott jikkonforma mal-ħtiġijiet essenzjali u ma

provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 2014/53/EU.

Page 71

ITG-100AI Embedded System

Page 61

Magyar [Hungarian]

IEI Integration Corp nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ

követelményeknek és az 2014/53/EU irányelv egyéb elõírásainak.

Polski [Polish]

IEI Integration Corp oświadcza, że wyrobu jest zgodny z zasadniczymi wymogami oraz

pozostałymi stosownymi postanowieniami Dyrektywy 2014/53/EU.

Português [Portuguese]

IEI Integration Corp declara que este equipamento está conforme com os requisitos

essenciais e outras disposições da Directiva 2014/53/EU.

Româna [Romanian]

IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele

esenţiale şi cu celelalte prevederi relevante ale Directivei 2014/53/EU.

Slovensko [Slovenian]

IEI Integration Corp izjavlja, da je ta opreme v skladu z bistvenimi zahtevami in ostalimi

relevantnimi določili direktive 2014/53/EU.

Slovensky [Slovak]

IEI Integration Corp týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky

príslušné ustanovenia Smernice 2014/53/EU.

Suomi [Finnish]

IEI Integration Corp vakuuttaa täten että laitteet on direktiivin 2014/53/EU oleellisten

vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Svenska [Swedish]

IEI Integration Corp förklarar att denna utrustningstyp står I överensstämmelse med de

väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv

2014/53/EU.

Page 72

ITG-100AI Embedded System

Page 62

is equipment complies with Part 15 of the FCC Rules. Operation is subject to the

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

on of this

frequency energy and, if not

FCC WARNING

following two conditions:

 This device may not cause harmful interference, and

 This device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital

reasonable protection against harmful interference when the equipment is operated in a

manual, may cause harmful interference to radio communications. Operati

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Federal Communication Commission Interference Statement

This equipment has been assembled with components that comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Page 73

ITG-100AI Embedded System

Page 63

B Safety Precautions

Appendix

Page 74

ITG-100AI Embedded System

Page 64

The precautions outlined in this chapter should be strictly followed.

WARNING:

Failure to follow these precautions may result in permanent damage to

the ITG-100AI.

B.1 Safety Precautions

Please follow the safety precautions outlined in the sections that follow:

B.1.1 General Safety Precautions

Please ensure the following safety precautions are adhered to at all times.

 Follow the electrostatic precautions outlined below whenever the device is

opened.

 Make sure the power is turned off and the power cord is disconnected

whenever the ITG-100AI is being installed, moved or modified.

 To prevent the risk of electric shock, make sure power cord is

unplugged from wall socket. To fully disengage the power to the unit,

please disconnect the power cord from the AC outlet. Refer servicing to

qualified service personnel. The AC outlet shall be readily available and

accessible.

 Do not apply voltage levels that exceed the specified voltage range.

Doing so may cause fire and/or an electrical shock. Use a power cord that

matches the voltage of the power outlet, which has been approved and

complies with the safety standard of your particular country.

 Electric shocks can occur if the ITG-100AI chassis is opened when it is

running. To avoid risk of electric shock, this device must only be connected to

a supply mains with protective earth.

 Do not drop or insert any objects into the ventilation openings of the

ITG-100AI.

Page 75

ITG-100AI Embedded System

Page 65

 If considerable amounts of dust, water, or fluids enter the device, turn off

the power supply immediately, unplug the power cord, and contact the

ITG-100AI vendor.

 DO NOT:

o Drop the device against a hard surface. o Strike or exert excessive force onto the LCD panel. o Touch any of the LCD panels with a sharp object o In a site where the ambient temperature exceeds the rated temperature

B.1.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the ITG-100AI

may result in permanent damage to the ITG-100AI and severe injury to

the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the ITG-100AI. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the ITG-100AI is opened and any of the electrical components are

handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband: Wearing a simple anti-static wristband can

help to prevent ESD from damaging any electrical component.

 Self-grounding: Before handling any electrical component, touch any

grounded conducting material. During the time the electrical component is

handled, frequently touch any conducting materials that are connected to the

ground.

 Use an anti-static pad: When configuring or working with an electrical

component, place it on an anti-static pad. This reduces the possibility of ESD

 Only handle the edges of the electrical component: When handling the

damage.

electrical component, hold the electrical component by its edges.

Page 76

ITG-100AI Embedded System

Page 66

instructions and local

B.1.3 Product Disposal

CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Only

certified engineers should replace the on-board battery.

Dispose of used batteries according to

regulations.

 Outside the European Union–If you wish to dispose of used electrical and

electronic products outside the European Union, please contact your local

authority so as to comply with the correct disposal method.

 Within the European Union–The device that produces less waste and is

easier to recycle is classified as electronic device in terms of the European

Directive 2012/19/EU (WEEE), and must not be disposed of as domestic

garbage.

EU-wide legislation, as implemented in each Member State, requires that

waste electrical and electronic products carrying the mark (left) must be

disposed of separately from normal household waste. This includes

monitors and electrical accessories, such as signal cables or power

cords. When you need to dispose of your display products, please follow

the guidance of your local authority, or ask the shop where you purchased the product.

The mark on electrical and electronic products only applies to the current European Union

Member States.

Please follow the national guidelines for electrical and electronic product disposal.

Page 77

ITG-100AI Embedded System

Page 67

B.2 Maintenance and Cleaning Precautions

When maintaining or cleaning the ITG-100AI, please follow the guidelines below.

WARNING:

 For safety reasons, turn-off the power and unplug the panel PC

before cleaning.

 If you dropped any material or liquid such as water onto the panel

PC when cleaning, unplug the power cable immediately and contact

your dealer or the nearest service center. Always make sure your

hands are dry when unplugging the power cable.

B.2.1 Maintenance and Cleaning

Prior to cleaning any part or component of the ITG-100AI, please read the details below.

 Except for the LCD panel, never spray or squirt liquids directly onto any other

components. To clean the LCD panel, gently wipe it with a piece of soft dry

cloth or a slightly moistened cloth.

 The interior of the device does not require cleaning. Keep fluids away from the

device interior.

 Be cautious of all small removable components when vacuuming the device.

 Never drop any objects or liquids through the openings of the device.

 Be cautious of any possible allergic reactions to solvents or chemicals used

when cleaning the device.

 Avoid eating, drinking and smoking within vicinity of the device.

B.2.2 Cleaning Tools

Some components in the ITG-100AI may only be cleaned using a product specifically

designed for the purpose. In such case, the product will be explicitly mentioned in the

cleaning tips. Below is a list of items to use when cleaning the ITG-100AI.

 Cloth– Although paper towels or tissues can be used, a soft, clean piece of

 Water or rubbing alcohol–A cloth moistened with water or rubbing alcohol

cloth is recommended when cleaning the device.

Page 78

ITG-100AI Embedded System

Page 68

can be used to clean the device.

 Using solvents–The use of solvents is not recommended when cleaning the

device as they may damage the plastic parts.

 Vacuum cleaner–Using a vacuum specifically designed for computers is

one of the best methods of cleaning the device. Dust and dirt can restrict the

airflow in the device and cause its circuitry to corrode.

 Cotton swabs–Cotton swaps moistened with rubbing alcohol or water are

excellent tools for wiping hard to reach areas.

 Foam swabs–Whenever possible, it is best to use lint free swabs such as

foam swabs for cleaning.

Page 79

ITG-100AI Embedded System

Page 69

Appendix

C BIOS Menu Options

Page 80

ITG-100AI Embedded System

Page 70



Below is a list of BIOS configuration options in the BIOS chapter.

System Date [xx/xx/xx] ........................................................................................................ 29

System Time [xx:xx:xx] ....................................................................................................... 29

ACPI Sleep State [S3 only (Suspend to RAM)] ................................................................. 30

Serial Port [Enabled] ............................................................................................................ 32

Device Mode [RS232] ........................................................................................................... 32

Serial Port [Enabled] ............................................................................................................ 32

Device Mode [RS232] ........................................................................................................... 32

Serial Port [Enabled] ............................................................................................................ 33

PC Health Status .................................................................................................................. 34

Wake system with Fixed Time [Disabled] .......................................................................... 35

Console Redirection [Disabled] ......................................................................................... 36

Terminal Type [ANSI] ........................................................................................................... 37

Bits per second [115200] ..................................................................................................... 37

Data Bits [8] .......................................................................................................................... 38

Parity [None] ......................................................................................................................... 38

Stop Bits [1] .......................................................................................................................... 38

Intel® Virtualization Technology [Disabled] ...................................................................... 39

EIST [Enabled] ...................................................................................................................... 39

C-States [Disabled] .............................................................................................................. 40

USB Devices ......................................................................................................................... 40

Legacy USB Support [Enabled] .......................................................................................... 41

Auto Recovery Function [Disabled] ................................................................................... 41

SATA Mode Selection [AHCI] .............................................................................................. 42

Hot Plug [Disabled] .............................................................................................................. 42

Memory Information ............................................................................................................ 44

Primary Display [IGD] .......................................................................................................... 45

DVMT Pre-Allocated [256MB] .............................................................................................. 45

DVMT Total Gfx Mem [Max] ................................................................................................. 46

Restore AC Power Loss [Last State] ................................................................................. 46

Power Saving Function (EUP) [Disabled] .......................................................................... 47

OS Selection [Windows] ...................................................................................................... 47

Compliance Mode [Disabled] .............................................................................................. 47

Page 81

ITG-100AI Embedded System

Page 71



PCIe Speed [Auto] ................................................................................................................ 48

SCC SD Card Support [Enabled] ........................................................................................ 48

SCC eMMC Support [Enabled] ............................................................................................ 49

eMMC Max Speed [HS400] .................................................................................................. 49

Administrator Password ..................................................................................................... 50

User Password ..................................................................................................................... 50

Bootup NumLock State [On] ............................................................................................... 50

Quiet Boot [Enabled] ........................................................................................................... 51

Launch PXE OpROM [Disabled] ......................................................................................... 51

Option ROM Messages [Force BIOS] ................................................................................. 51

UEFI Boot [Disabled] ........................................................................................................... 51

Boot Option Priority ............................................................................................................. 52

Hard Drive BBS Priorities .................................................................................................... 52

Save Changes and Reset .................................................................................................... 53

Discard Changes and Reset ............................................................................................... 53

Restore Defaults .................................................................................................................. 53

Save as User Defaults ......................................................................................................... 53

Restore User Defaults ......................................................................................................... 53

Page 82

ITG-100AI Embedded System

Page 72

Appendix

D Terminology

Page 83

ITG-100AI Embedded System

Page 73

AC ’97

ACPI

AHCI

ATA

ARMD

ASKIR

BIOS

Audio Codec 97 (AC’97) refers to a codec standard developed by Intel®

in 1997.

Advanced Configuration and Power Interface (ACPI) is an OS-directed

configuration, power management, and thermal management interface.

Advanced Host Controller Interface (AHCI) is a SATA Host controller

The Advanced Technology Attachment (ATA) interface connects storage

devices including hard disks and CD-ROM drives to a computer.

An ATAPI Removable Media Device (ARMD) is any ATAPI device that

supports removable media, besides CD and DVD drives.

Amplitude Shift Keyed Infrared (ASKIR) is a form of modulation that

represents a digital signal by varying the amplitude (“volume”) of the

signal. A low amplitude signal represents a binary 0, while a high

amplitude signal represents a binary 1.

The Basic Input/Output System (BIOS) is firmware that is first run when

CODEC

CompactFlash®

CMOS

COM

DAC

DDR

the computer is turned on and can be configured by the end user

The Compressor-Decompressor (CODEC) encodes and decodes digital

audio data on the system.

CompactFlash® is a solid-state storage device. CompactFlash® devices

use flash memory in a standard size enclosure. Type II is thicker than

Type I, but a Type II slot can support both types.

Complimentary metal-oxide-conductor is an integrated circuit used in

chips like static RAM and microprocessors.

COM refers to serial ports. Serial ports offer serial communication to

expansion devices. The serial port on a personal computer is usually a

male D-sub 9 connector.

The Digital-to-Analog Converter (DAC) converts digital signals to analog

signals.

Double Data Rate refers to a data bus transferring data on both the rising

and falling edges of the clock signal.

Page 84

ITG-100AI Embedded System

Page 74

DMA

DIMM

DIO

EHCI

EIDE

EIST

Direct Memory Access (DMA) enables some peripheral devices to

bypass the system processor and communicate directly with the system

memory.

Dual Inline Memory Modules are a type of RAM that offer a 64-bit data

bus and have separate electrical contacts on each side of the module.

The digital inputs and digital outputs are general control signals that

control the on/off circuit of external devices or TTL devices. Data can be

read or written to the selected address to enable the DIO functions.

The Enhanced Host Controller Interface (EHCI) specification is a

Enhanced IDE (EIDE) is a newer IDE interface standard that has data

transfer rates between 4.0 MBps and 16.6 MBps.

Enhanced Intel® SpeedStep Technology (EIST) allows users to modify

the power consumption levels and processor performance through

application software. The application software changes the bus-to-core

FSB

GbE

GPIO

HDD

ICH

IrDA

L1 Cache

L2 Cache

frequency ratio and the processor core voltage.

The Front Side Bus (FSB) is the bi-directional communication channel

between the processor and the Northbridge chipset.

Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0

Gbps and complies with the IEEE 802.3-2005 standard.

General purpose input

Hard disk drive (HDD) is a type of magnetic, non-volatile computer

storage device that stores digitally encoded data.

The Input/Ouput Controll Hub (ICH) is an Intel® Southbridge chipset.

Infrared Data Association (IrDA) specify infrared data transmission

protocols used to enable electronic devices to wirelessly communicate

with each other.

The Level 1 Cache (L1 Cache) is a small memory cache built into the

system processor.

The Level 2 Cache (L2 Cache) is an external processor memory cache.

Page 85

ITG-100AI Embedded System

Page 75

transfers between storage devices and the computer chipsets. The SATA

LCD

LVDS

POST

RAM

SATA

S.M.A.R.T

Liquid crystal display (LCD) is a flat, low-power display device that

consists of two polarizing plates with a liquid crystal panel in between.

Low-voltage differential signaling (LVDS) is a dual-wire, high-speed

differential electrical signaling system commonly used to connect LCD

displays to a computer.

The Power-on Self Test (POST) is the pre-boot actions the system

performs when the system is turned-on.

Random Access Memory (RAM) is volatile memory that loses data when

power is lost. RAM has very fast data transfer rates compared to other

storage like hard drives.

Serial ATA (SATA) is a serial communications bus designed for data

bus has transfer speeds up to 1.5 Gbps and the SATA II bus has data

transfer speeds of up to 3.0 Gbps.

Self Monitoring Analysis and Reporting Technology (S.M.A.R.T) refers to

UART

UHCI

USB

VGA

automatic status checking technology implemented on hard disk drives.

Universal Asynchronous Receiver-transmitter (UART) is responsible for

asynchronous communications on the system and manages the system’s

serial communication (COM) ports.

The Universal Host Controller Interface (UHCI) specification is a

The Universal Serial Bus (USB) is an external bus standard for

interfacing devices. USB 1.1 supports 12Mbps data transfer rates and

USB 2.0 supports 480Mbps data transfer rates.

The Video Graphics Array (VGA) is a graphics display system developed

by IBM.

Page 86

ITG-100AI Embedded System

Page 76

Appendix

E Hazardous Materials

Disclosure

Page 87

ITG-100AI Embedded System

Page 77

The details provided in this appendix are to ensure that the product is compliant with the

Peoples Republic of China (China) RoHS standards. The table below acknowledges the

presences of small quantities of certain materials in the product, and is applicable to China

RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly

Use Period” (EFUP). This is an estimate of the number of years that these substances

would “not leak out or undergo abrupt change.” This product may contain replaceable

sub-assemblies/components which have a shorter EFUP such as batteries and lamps.

These components will be separately marked.

Please refer to the following table.

Part Name Toxic or Hazardous Substances and Elements

Lead

(Pb)

Housing

Display

Printed Circuit

Board

Metal Fasteners

Cable Assembly

Fan Assembly

Power Supply

Assemblies

Battery

O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below the limit

requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part is above

O O O O O O

Mercury

(Hg)

Cadmium

(Cd)

Hexavalent

Chromium

(CR(VI))

Polybrominated

Biphenyls

(PBB)

Polybrominated

Diphenyl Ethers

(PBDE)

the limit requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

Page 88

ITG-100AI Embedded System

Page 78

部件名称

有毒有害物质或元素

铅

汞

镉

六价铬

多溴联苯

多溴二苯

醚

壳体

显示

印刷电路板

金属螺帽

电缆组装

风扇组装

电力供应组装

电池

此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符

合中国 RoHS 标准规定的限量要求。

本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的

年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元

件将会单独标示出来。

(Pb)

O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T 11363-2006 (现由 GB/T 26572-2011 取代)

标准规定的限量要求以下。

O O O O O O

(Hg)

(Cd)

(CR(VI))

(PBB)

(PBDE)

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 (现由 GB/T

26572-2011 取代) 标准规定的限量要求。

IEI Technology ITG-100AI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Introduction

1.1 Overview

1.2 Features

1.3 Technical Specifications

1.4 Side Panel

1.5 Front Panel

1.6 Physical Dimensions

2 Unpacking

2.1 Unpacking

2.2 Packing List

3 Installation

3.1 Anti-static Precautions

3.2 Installation Precautions

3.3 Bottom Cover Removal and Re-installation

3.4 SO-DIMM Installation

3.5 Wireless LAN Module Installation (Optional)

3.6 RS-232/422/485 Serial Port Connection

3.6.1 DB-9 RS-232/422/485 Serial Port Connection

3.6.2 RJ-45 RS-232/422/485 Serial Port Connection

3.7 AT/ATX Mode Selection

3.7.1 AT Power Mode

3.7.2 ATX Power Mode

3.8 Mounting the System

3.9 Powering On/Off the System

3.10 Reset the System

4 BIOS

4.1 Introduction

4.1.1 Starting Setup

4.1.2 Using Setup

4.1.3 Getting Help

4.1.4 Unable to Reboot after Configuration Changes

4.1.5 BIOS Menu Bar

4.2 Main

4.3 Advanced

4.3.1 ACPI Settings

4.3.2 F81866 Super IO Configuration

4.3.2.1 Serial Port n Configuration

4.3.2.1.1 Serial Port 1 Configuration

4.3.2.1.2 Serial Port 2 Configuration

4.3.2.1.3 Serial Port 3 Configuration

4.3.2.1.4 Serial Port 4 Configuration

4.3.3 Hardware Monitor

4.3.4 RTC Wake Settings

4.3.5 Serial Port Console Redirection

4.3.5.1 Console Redirection Settings

4.3.6 CPU Configuration

4.3.7 USB Configuration

4.3.8 iEi Feature

4.3.9 SATA Configuration

4.4 Chipset

4.4.1 North Bridge Configuration

4.4.1.1 Intel IGD Configuration

4.4.2 Southbridge Configuration

4.4.2.1 PCI Express Configuration

4.4.2.2 SCC Configuration

4.5 Security

4.6 Boot

4.7 Exit

5 Software Installation

5.1 Available Drivers

5.1.1 Driver Download

5.2 OpenVINO™ Toolkit Installation

A Regulatory Compliance

B Safety Precautions

B.1 Safety Precautions

B.1.1 General Safety Precautions

B.1.2 Anti-static Precautions

B.1.3 Product Disposal

B.2 Maintenance and Cleaning Precautions

B.2.1 Maintenance and Cleaning

B.2.2 Cleaning Tools

C BIOS Menu Options

D Terminology