Page 1
IEI Technology Corp.
User Manual
ISDM Series Industrial Monitor
ISDM Series Industrial Monitor User Manual
MODEL:
ISDM Series
Stainless Steel Industrial Monitor, RoHS Compliance
IP 65 Protection, Touch Screen, 9-36V DC Input, VGA/DVI-D
Rev. 1.13 – 16 July, 2009
Page 1
Page 2
ISDM Series Industrial Monitor
Revision
Date Version Changes
16 July, 2009 1.13 Update “Chapter 6: OSD Controls”
April, 2008 1.12 1. Added ISDM-121GX models information
2. Added the smartOSD appendix
May, 2007 1.11 AV-5300 AD Board CN25 connector pin 3 voltage changed to
+9V~+36V input
April, 2007 1.10 Updated Figure 1-3 and Section 4.3 for AV-5300 AD Board V2.0
October, 2006 1.00 Initial Release
Page 2
Page 3
ISDM Series Industrial Monitor
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
Copyright
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page 3
Page 4
ISDM Series Industrial Monitor
Manual Conventions
WARNING!
Warnings appear where overlooked details may cause damage to the equipment or result
in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.
The word “warning” is written as “WARNING,” both capitalized and bold and is followed by
text. The text is the warning message. A warning message is shown below:
WARNING:
This is an example of a warning message. Failure to adhere to warning
messages may result in permanent damage to the ISDM Series or
personal injury to the user. Please take warning messages seriously.
CAUTION!
Cautionary messages should also be heeded to help reduce the chance of losing data or
damaging the ISDM Series. Cautions are easy to recognize. The word “caution” is written
as “CAUTION,” both capitalized and bold and is followed. The italicized text is the
cautionary message. A caution message is shown below:
Page 4
Page 5
ISDM Series Industrial Monitor
CAUTION:
This is an example of a caution message. Failure to adhere to cautions
messages may result in permanent damage to the ISDM Series.
Please take caution messages seriously.
NOTE:
These messages inform the reader of essential but non-critical information. These
messages should be read carefully as any directions or instructions contained therein can
help avoid making mistakes. Notes are easy to recognize. The word “note” is written as
“NOTE,” both capitalized and bold and is followed by text. The text is the cautionary
message. A note message is shown below:
NOTE:
This is an example of a note message. Notes should always be read.
Notes contain critical information about the ISDM Series. Please take
note messages seriously.
Page 5
Page 6
ISDM Series Industrial Monitor
Packing List
NOTE:
If any of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the ISDM Series from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to
The items listed below should all be included in the ISDM Series package.
1 x ISDM-190/170/150/121/104/84 series industrial monitor.
1 x AC Power cable
1 x VGA Cable
1 x 45W AC Power Adapter (ISDM-190 / 170 / 150 / 121)
1 x 25W AC Power Adapter (ISDM-104 / 84)
5 x Replacement Round Head Screw
5 x Replacement Flat Head Screw
5 x Replacement Wire Strain Band
1 x User Manual on CDROM
1 x Power Cable for Terminal Block (Optional for M model)
1 x Touch Panel RS-232 Cable / Touch Pen / Driver CDROM (for T-R model)
1 x Touch Panel USB Cable / Touch Pen / Driver CDROM (for USB/T-R
sales@iei.com.tw.
Page 6
model)
Images of the above items are shown in Chapter 5.
Page 7
ISDM Series Industrial Monitor
Table of Contents
1 INTRODUCTION................................................................................................... 18
1.1 ISDM SERIES INDUSTRIAL MONITOR OVERVIEW..................................................... 19
1.1.1 Standard Features............................................................................................ 19
1.1.2 Model Variations.............................................................................................. 19
1.1.3 Base Model Variants ........................................................................................ 20
1.2 APPLICATIONS AND FEATURES.................................................................................. 20
1.2.1 ISDM Series Industrial Monitor Applications................................................. 20
1.2.2 ISDM Series Industrial Monitor Features....................................................... 21
1.3 EXTERNAL OVERVIEW.............................................................................................. 21
1.3.1 Front View........................................................................................................ 22
1.3.2 Bottom Panel View........................................................................................... 22
1.3.3 AD Board ......................................................................................................... 23
1.4 SERIES SPECIFICATIONS............................................................................................ 23
1.5 CERTIFICATIONS ....................................................................................................... 25
2 MECHANICAL OVERVIEW............................................................................... 26
2.1 INTRODUCTION......................................................................................................... 27
2.2 FRONT PANEL........................................................................................................... 27
2.3 REAR PANEL............................................................................................................. 27
2.4 BOTTOM PANEL........................................................................................................ 28
2.4.1 A vailable Connectors....................................................................................... 28
2.4.2 ISDM-084 Connectors..................................................................................... 28
2.4.3 ISDM-104 Connectors..................................................................................... 29
2.4.4 ISDM-121 Connectors..................................................................................... 29
2.4.5 ISDM-150 Connectors..................................................................................... 29
2.4.6 ISDM-170 Connectors..................................................................................... 30
2.4.7 ISDM-190 Connectors..................................................................................... 30
2.5 PHYSICAL DIMENSIONS............................................................................................ 31
2.5.1 General Physical Dimensions.......................................................................... 31
2.5.2 ISDM-190 Physical Dimensions...................................................................... 31
2.5.3 ISDM-170 Physical Dimensions...................................................................... 33
Page 7
Page 8
2.5.4 ISDM-150 Physical Dimensions...................................................................... 34
2.5.5 ISDM-121 Physical Dimensions...................................................................... 35
2.5.6 ISDM-104 Physical Dimensions...................................................................... 36
2.5.7 ISDM-084 Physical Dimensions...................................................................... 37
2.6 OPTIONAL MOUNTING KITS ..................................................................................... 38
2.6.1 ISDM-084 Mounting Kits................................................................................. 38
2.6.2 ISDM-104 Mounting Kits................................................................................. 38
2.6.3 ISDM-121 Mounting Kits................................................................................. 38
2.6.4 ISDM-150 Mounting Kits................................................................................. 39
2.6.5 ISDM-170 Mounting Kits................................................................................. 39
2.6.6 ISDM-190 Mounting Kits................................................................................. 39
2.7 MOUNTING OPTIONS................................................................................................ 40
2.7.1 Panel Mounting................................................................................................ 40
2.7.2 Wall Mounting.................................................................................................. 41
ISDM Series Industrial Monitor
2.7.3 Monitor Arm or Stand Mounting......................................................................42
3 LCD AND TOUCH PANEL SPECIFICATIONS ................................................ 44
3.1 LCD SPECIFICATIONS............................................................................................... 45
3.1.1 LCD Overview ................................................................................................. 45
3.1.2 ISDM-190 LCD Specifications ........................................................................ 46
3.1.3 ISDM-170 LCD Specifications ........................................................................ 47
3.1.4 ISDM-150 LCD Specifications ........................................................................ 48
3.1.5 ISDM-121 LCD Specifications ........................................................................ 49
3.1.6 ISDM-104 LCD Specifications ........................................................................ 50
3.1.7 ISDM-084 LCD Specifications ........................................................................ 51
3.2 TOUCH PANELS......................................................................................................... 52
3.2.1 Touch Panel Models......................................................................................... 52
3.2.2 Touch Panel Dimensions.................................................................................. 53
3.2.3 Touch Panel Specifications .............................................................................. 54
3.2.4 Touch Panel RS-232 Controller Specifications................................................ 55
3.2.5 Touch Panel USB Controller Specifications.................................................... 56
3.3 POWER ADAPTERS.................................................................................................... 57
4 AD BOARDS........................................................................................................... 58
4.1 AD BOARD OVERVIEW............................................................................................. 59
Page 8
Page 9
ISDM Series Industrial Monitor
4.2 AV-5350 AD BOARD................................................................................................ 59
4.2.1 AV-5350 AD Board Overview .......................................................................... 59
4.2.2 AV-5350 AD Board Connectors .......................................................................59
4.2.3 AV-5350 AD Board Layout............................................................................... 60
4.2.4 AV-5350 Peripheral Interface Connectors....................................................... 61
4.2.5 AV-5350 Rear Panel Connectors..................................................................... 61
4.2.6 AV-5350 On-board Jumper ..............................................................................62
4.2.7 AV-5350 Internal Peripheral Connectors........................................................ 62
4.2.8 5V Power Connector........................................................................................ 62
4.2.9 Backlight Inverter Connector .......................................................................... 63
4.2.10 External OSD and LED Indication Connector.............................................. 64
4.2.11 LVDS Output Connector ................................................................................ 66
4.2.12 VGA Connector.............................................................................................. 67
4.2.13 AV-5350 External (Rear Panel) Connectors.................................................. 68
4.2.14 DC 12V Connector......................................................................................... 69
4.2.15 VGA Connector.............................................................................................. 69
4.2.16 AV-5350 On-board Jumper ............................................................................70
4.2.17 LCD Panel Voltage Select Jumper................................................................. 71
4.3 AV-5300 AD BOARD OVERVIEW.............................................................................. 72
4.3.1 AV-5300 AD Board Connectors .......................................................................73
4.3.2 AV-5300 AD Board Layout............................................................................... 74
4.3.3 AV-5300 Peripheral Interface Connectors....................................................... 75
4.3.4 AV-5300 Rear Panel Connectors..................................................................... 75
4.3.5 AV-5300 On-board Jumpers............................................................................. 76
4.3.6 AV-5300 Internal Peripheral Connectors........................................................ 76
4.3.7 Auto-Dimming Connector................................................................................ 76
4.3.8 Debug Port Connector..................................................................................... 77
4.3.9 External OSD and LED Indication Connector................................................ 78
4.3.10 Backlight Inverter Connector ........................................................................ 79
4.3.11 LVDS Output Connector ................................................................................ 80
4.3.12 Power Output Connector............................................................................... 81
4.3.13 Power Input Connector.................................................................................. 82
4.3.14 VGA Connector.............................................................................................. 84
4.3.15 AV-5300 On-board Jumpers........................................................................... 85
4.3.16 LCD Panel Power Input Jumper.................................................................... 86
Page 9
Page 10
4.3.17 LCD Panel Voltage Select Jumper................................................................. 86
4.3.18 AV-5300 External (Rear Panel) Connectors.................................................. 87
4.3.19 DC 12V Connector......................................................................................... 87
4.3.20 VGA Connector.............................................................................................. 88
4.3.21 DVI-D Connector........................................................................................... 89
5 INSTALLATION .................................................................................................... 91
5.1 INSTALLATION PRECAUTIONS ................................................................................... 92
5.2 UNPACKING.............................................................................................................. 93
5.2.1 Packaging ........................................................................................................ 93
5.2.2 Unpacking Procedure ...................................................................................... 93
5.2.3 Packing List ..................................................................................................... 94
5.3 PRE-INSTALLATION PREPARATION ............................................................................ 94
5.3.1 Tools................................................................................................................. 94
5.3.2 Voltage Select Jumper Settings ........................................................................ 95
ISDM Series Industrial Monitor
5.4 CONNECTORS ........................................................................................................... 96
5.4.1 Rear Panel Connectors Overview.................................................................... 97
5.4.2 VGA Connector................................................................................................ 97
5.4.3 DVI-D Connector............................................................................................. 98
5.4.4 12V Power Connector...................................................................................... 98
5.4.5 Optional DC Power Connector ....................................................................... 99
5.4.6 Optional RS-232 Touch Panel Connector........................................................ 99
5.4.7 Optional USB Touch Panel Connector .......................................................... 100
5.5 MOUNTING THE ISDM SERIES INDUSTRIAL MONITOR........................................... 101
5.5.1 Panel Mounting.............................................................................................. 101
5.5.1.1 Standard Panel Mounting........................................................................ 101
5.5.2 Wall Mounting................................................................................................ 104
5.5.3 Monitor Stand Installation............................................................................. 106
5.5.4 Monitor Arm Installation............................................................................... 107
6 ON-SCREEN-DISPLAY (OSD) CONTROLS................................................... 109
6.1 USER MODE OSD STRUCTURE................................................................................110
6.1.1 OSD Buttons....................................................................................................110
6.1.2 OSD Menu Structure.......................................................................................111
6.2 USING THE OSD......................................................................................................112
Page 10
Page 11
ISDM Series Industrial Monitor
6.2.1 Main Display Features....................................................................................112
6.2.2 Gamma............................................................................................................113
6.2.3 Color...............................................................................................................114
6.2.4 Image Settings.................................................................................................115
6.2.5 OSD Configurations........................................................................................116
6.2.6 Signal ..............................................................................................................117
7 SOFTWARE DRIVERS ........................................................................................119
7.1 INTRODUCTION....................................................................................................... 120
7.2 DRIVER INSTALLATION........................................................................................... 120
7.3 TOUCH PANEL DRIVER CONFIGURATION ................................................................ 127
A SAFETY PRECAUTIONS................................................................................... 129
A.1 SAFETY PRECAUTIONS .......................................................................................... 130
A.1.1 General Safety Precautions........................................................................... 130
A.1.2 Anti-static Precautions.................................................................................. 131
A.2 MAINTENANCE AND CLEANING PRECAUTIONS...................................................... 131
A.2.1 Maintenance and Cleaning............................................................................ 131
A.2.2 Cleaning Tools............................................................................................... 132
B CERTIFICATIONS.............................................................................................. 133
B.1 ROHS COMPLIANT ................................................................................................134
B.2 IP 65 COMPLIANT FRONT PANEL ........................................................................... 134
C SMARTOSD.......................................................................................................... 135
C.1 IEI SMARTOSD QUICK INSTALLATION GUIDE ....................................................... 136
C.2 PRE-INSTALLATION NOTICE ................................................................................... 136
C.3 SMARTOSD INSTALL ............................................................................................. 136
C.4 SOFTWARE ILLUSTRATION ..................................................................................... 140
C.4.1 Manage Page................................................................................................. 142
C.4.2 EDID Page.................................................................................................... 143
C.4.3 Image Page.................................................................................................... 144
C.4.4 Display Page (for analog signal).................................................................. 145
C.4.5 Color Page .................................................................................................... 146
C.4.6 PIP Page........................................................................................................ 147
C.4.7 System Page................................................................................................... 148
Page 11
Page 12
C.4.8 About Page ....................................................................................................149
C.5 SMARTOSD FAQ................................................................................................... 150
C.5.1 Windows 2000 Installation Failure............................................................... 150
C.5.2 Vista Installation Failure............................................................................... 151
C.5.3 Model Failure................................................................................................ 152
C.5.4 DCC Port Failure.......................................................................................... 152
ISDM Series Industrial Monitor
Page 12
Page 13
ISDM Series Industrial Monitor
Figure 1-1: ISDM Series Front View...........................................................................22
Figure 1-2: Typical Bottom Panel View.....................................................................22
Figure 1-3: AV-5300 AD Board...................................................................................23
Figure 2-1: Front Panel...............................................................................................27
Figure 2-2: Rear Panel ................................................................................................28
Figure 2-3: ISDM-190 Physical Dimensions (millimeters).......................................32
Figure 2-4: ISDM-170 Physical Dimensions (millimeters).......................................33
Figure 2-5: ISDM-150 Physical Dimensions (millimeters).......................................34
Figure 2-6: ISDM-121 Physical Dimensions (millimeters).......................................35
List of Figures
Figure 2-7: ISDM-104 Physical Dimensions (millimeters).......................................36
Figure 2-8: ISDM-084 Physical Dimensions (millimeters).......................................37
Figure 2-9: Typical Panel Mounting...........................................................................40
Figure 2-10: Typical Wall Mounting...........................................................................41
Figure 2-11: Typical Monitor Arm or Stand Mounting.............................................42
Figure 4-1: AV-5350 AD Board Overview..................................................................59
Figure 4-2: Connector and Jumper Locations .........................................................60
Figure 4-3: 5V Power Connector Location ...............................................................63
Figure 4-4: Backlight Inverter Connector Location.................................................64
Figure 4-5: External OSD and LED Indication Connector Location.......................65
Figure 4-6: LVDS Output Connector Location .........................................................67
Figure 4-7: VGA Connector Location........................................................................68
Figure 4-8: AV-5350 External (Rear Panel) Connectors..........................................69
Figure 4-9: VGA Connector Pinout Locations..........................................................70
Figure 4-10: Jumpers..................................................................................................70
Figure 4-11: Jumper Location....................................................................................71
Figure 4-12: AV-5300 AD Board Overview................................................................72
Figure 4-13: Connector and Jumper Locations.......................................................74
Page 13
Page 14
Figure 4-14: Auto-dimming Connector Location.....................................................77
Figure 4-15: Debug Port Connector Location ..........................................................78
Figure 4-16: External OSD and LED Indication Connector Location.....................79
Figure 4-17: Backlight Inverter Connector Location...............................................80
Figure 4-18: LVDS Output Connector Location .......................................................81
Figure 4-19: Power Output Connector Locations....................................................82
Figure 4-20: Power Input Connector Locations.......................................................83
Figure 4-21: VGA Connector Location......................................................................84
Figure 4-22: Jumpers..................................................................................................85
Figure 4-23: Jumper Locations..................................................................................85
Figure 4-24: AV-5300 External (Rear Panel) Connectors........................................87
Figure 4-25: VGA Connector Pinout Locations........................................................88
Figure 4-26: DVI-D Connector Pinout Locations......................................................90
ISDM Series Industrial Monitor
Figure 5-1: Monitor Rear Panel Connections...........................................................97
Figure 5-2: VGA Connector........................................................................................98
Figure 5-3: DVI-D Connector......................................................................................98
Figure 5-4: 12V Power Connector..............................................................................99
Figure 5-5: DC Power Connector...............................................................................99
Figure 5-6: Optional RS-232 Touch Panel Connector .......................................... 100
Figure 5-7: Optional USB Touch Panel Connector............................................... 100
Figure 5-8: Panel Opening....................................................................................... 102
Figure 5-9: Insert the Monitor ................................................................................. 102
Figure 5-10: Panel Mounting Clamp Position........................................................ 103
Figure 5-11: Wall-mounting Bracket....................................................................... 104
Figure 5-12: Monitor Support Screws.................................................................... 105
Figure 5-13: Wall Mounting the Monitor................................................................. 106
Figure 5-14: VESA Mounting Holes........................................................................ 106
Figure 5-15: Monitor Stand Mounting .................................................................... 107
Page 14
Figure 5-16: Monitor Arm Mounting....................................................................... 108
Figure 6-1: OSD Control Buttons for ISDM Series................................................ 110
Figure 6-2: Main Display Features.......................................................................... 112
Figure 6-3: Color Options........................................................................................ 113
Page 15
ISDM Series Industrial Monitor
Figure 6-4: Color Options........................................................................................ 114
Figure 6-5: Image Settings Menu............................................................................ 115
Figure 6-6: OSD Configurations Menu................................................................... 116
Figure 6-7: Signal Menu........................................................................................... 117
Figure 7-1: Driver CD Pop Up Screen..................................................................... 121
Figure 7-2: Install Shield Wizard Preparation........................................................ 122
Figure 7-3: Welcome Screen................................................................................... 122
Figure 7-4: Install PS/2 Interface Driver................................................................. 123
Figure 7-5: Install PS/2 Interface Driver................................................................. 124
Figure 7-6: Touch Monitor/USB Touch Controller Confirmation ........................ 124
Figure 7-7: Controller Installation Directory.......................................................... 125
Figure 7-8: Program Icon Directory........................................................................ 126
Figure 7-9: Installing................................................................................................ 126
Figure 7-10: Installation Complete ......................................................................... 127
Figure 8-2: smartOSD Installer ............................................................................... 137
Figure 8-3: smartOSD Welcome Screen ................................................................ 137
Figure 8-4: smartOSD Folder Select Screen ......................................................... 138
Figure 8-5: smartOSD Confirm Installation ........................................................... 138
Figure 8-6: smartOSD Installation Progress ......................................................... 139
Figure 8-7: smartOSD Installation Complete......................................................... 139
Figure 8-8: Manage Page......................................................................................... 142
Figure C-9: DLL Missing.......................................................................................... 150
Figure C-10: Windows Vista Error.......................................................................... 151
Figure C-11: Install as Administrator..................................................................... 151
Figure C-12: Firmware Incompatibility................................................................... 152
Figure C-13: DCC Port Failure ................................................................................ 152
Page 15
Page 16
ISDM Series Industrial Monitor
List of Tables
Table 1-1: ISDM Series Base Model Variants...........................................................20
Table 1-2: ISDM Series Specifications......................................................................25
Table 2-1: General Physical Dimensions..................................................................31
Table 2-2: ISDM-084 Mounting Kits...........................................................................38
Table 2-3: ISDM-104 Mounting Kits...........................................................................38
Table 2-4: ISDM-121 Mounting Kits...........................................................................39
Table 2-5: ISDM-150 Mounting Kits...........................................................................39
Table 2-6: ISDM-170 Mounting Kits...........................................................................39
Table 2-7: ISDM-190 Mounting Kits...........................................................................40
Table 2-8: Panel Mounting Clamps............................................................................41
Table 3-1: ISDM-190 LCD Specifications ..................................................................46
Table 3-2: ISDM-170 LCD Specifications ..................................................................47
Table 3-3: ISDM-150 LCD Specifications ..................................................................48
Table 3-4: ISDM-121 LCD Specifications ..................................................................49
Table 3-5: ISDM-104 LCD Specifications ..................................................................50
Table 3-6: ISDM-084 LCD Specifications ..................................................................51
Table 3-7: Touch Panel Models..................................................................................52
Table 3-8: Touch Panel Dimensions (mm)................................................................53
Table 3-9: Touch Panel Specifications......................................................................54
Table 3-10: Touch Panel RS-232 Controller Specifications....................................55
Table 3-11: Touch Panel USB Controller Specifications.........................................56
Table 3-12: Power Adapter Specifications ...............................................................57
Table 4-1: AV-5350 Peripheral Interface Connectors ..............................................61
Table 4-2: AV-5350 Rear Panel Connectors .............................................................61
Page 16
Table 4-3: AV-5350 On-board Jumper.......................................................................62
Table 4-4: 5V Power Connector Pinouts...................................................................62
Table 4-5: Backlight Inverter Connector Pinouts.....................................................63
Table 4-6: External OSD and LED Indication Connector Pinouts..........................65
Page 17
ISDM Series Industrial Monitor
Table 4-7: LVDS Output Connector Pinouts.............................................................66
Table 4-8: VGA Connector Pinouts ........................................................................... 68
Table 4-9: DC 12V Connector Pinouts.......................................................................69
Table 4-10: VGA Connector Pinouts .........................................................................70
Table 4-11: LCD Panel Voltage Select Jumper Settings .........................................71
Table 4-12: AV-5300 Peripheral Interface Connectors ............................................75
Table 4-13: AV-5300 Rear Panel Connectors ...........................................................76
Table 4-14: AV-5300 On-board Jumpers...................................................................76
Table 4-15: Auto-dimming Connector Pinouts.........................................................77
Table 4-16: Debug Port Connector Pinouts..............................................................78
Table 4-17: External OSD and LED Indication Connector Pinouts........................79
Table 4-18: Backlight Inverter Connector Pinouts...................................................80
Table 4-19: LVDS Output Connector Pinouts...........................................................81
Table 4-20: Power Output Connector Pinouts (CN12).............................................82
Table 4-21: Power Output Connector Pinouts (CN13).............................................82
Table 4-22: Power Input Connector Pinouts (CN24)................................................83
Table 4-23: Power Input Connector Pinouts (CN25)................................................83
Table 4-24: VGA Connector Pinouts .........................................................................84
Table 4-25: LCD Panel Power Input Jumper Settings .............................................86
Table 4-26: LCD Panel Voltage Select Jumper Settings .........................................86
Table 4-27: DC 12V Connector Pinouts.....................................................................87
Table 4-28: VGA Connector Pinouts .........................................................................88
Table 4-29: DVI-D Connector Pinouts .......................................................................89
Table 5-1: Rear Panel Connectors.............................................................................96
Table 5-2: VGA Connector Pinouts ........................................................................... 97
Table 5-3: DVI-D Connector Pinouts .........................................................................98
Table 5-4: Optional RS-232 Touch Panel Connector Pinouts.............................. 100
Table 5-5: Optional USB Touch Panel Connector Pinouts .................................. 100
Table 6-1: OSD Menus ............................................................................................. 111
Table C-1: SmartOSD Menu Structure ................................................................... 141
Page 17
Page 18
ISDM Series Industrial Monitor
Chapter
1
1 Introduction
Page 18
Page 19
ISDM Series Industrial Monitor
1.1 ISDM Series Industrial Monitor Overview
The ISDM series industrial monitor is the latest member of IEI’s line of sophisticated LCD
designs, and it has been improved to be RoHS compliant. With the stainless steel frame,
the ISDM series is ideal for strict hygiene conditions, such as hospital, kitchens, abattoirs
and other food processing plants. The ISDM series is also designed to fit industrial
automation, or any other applications that require minimum installation space and
flexible configuration. The flat front panel provides IP 65 protection, which effectively
wards off dust and water. Flexible analog or digital interfaces are provided for ease of
connection with a management computer. All the ISDM series models come with a
resistive type touch panels. If remote/non-attentive control is preferred, RS-232 or USB
interfaces can be used with customized adapter cables.
1.1.1 Standard Features
All the base models listed in Section 1.2.1 have the following standard features
LCD monitor
Stainless steel front frame
Heavy-duty steel chassis
OSD function
IP 65 level protection
RoHS compliance
1.1.2 Model Variations
The ISDM LCD series have the following seven base models.
ISDM-084G: 8.4” LCD screen
ISDM-104G: 10.4” LCD screen
ISDM-121G: 12.1” LCD screen
ISDM-150G: 15” LCD screen
ISDM-170G: 17” LCD screen
ISDM-190G: 19” LCD screen
Page 19
Page 20
1.1.3 Base Model Variants
The ISDM series industrial monitor base models may or may not have a variety of variants.
The standard model name is ISDM-(XXX)G, where (XXX) refers to three digit size of the
ISDM Series Industrial Monitor
monitor. Special features with the associated model prefix are listed in
Model Number
High
Luminance
ISDM-(XXX)G/T-R - - Yes -
ISDM-(XXX)GM/T-R - Yes Yes -
ISDM-(XXX)GH/T-R Yes - Yes -
ISDM-(XXX)GHM/T-R Yes Yes Yes -
ISDM-(XXX)G-USB/T-R - - - Yes
ISDM-(XXX)GM-USB/T-R - Yes - Yes
ISDM-(XXX)GX/T-R - - Yes -
ISDM-(XXX)GXM/T-R - Yes Yes -
ISDM-(XXX)GX-USB/T-R - - - Yes
ISDM-(XXX)GXM-USB/T-R - Yes - Yes
9~36V
Touch
Power
Screen
Input
Table 1-1.
USB
Touch
Screen
Table 1-1: ISDM Series Base Model Variants
1.2 Applications and Features
1.2.1 ISDM Series Industrial Monitor Applications
The ISDM series industrial monitor is designed for strict hygiene conditions or rigorous
industrial environments. Its durability and strength also makes it an ideal choice for public
access computers. Some possible applications include:
Automation & Control
o Food processing plant environment monitoring
o Factory automation HMI terminal
o Shop-floor/MES control
Digital Surveillance
o Digital surveillance
Page 20
Page 21
ISDM Series Industrial Monitor
o X-ray imaging terminal
o Multimedia advertising platform
Self-service Kiosk
o Full-service receptionist kiosk
o Hospital self-registration terminal
General Computing
o Computer-based testing center
o General purpose information system
o Mobile nursing station
o Interactive education use
1.2.2 ISDM Series Industrial Monitor Features
Some of the features of the ISDM series industrial monitor include:
IP 65 compliant stainless steel front panel
Analog VGA interface supports most general system boards
RS-232 or USB interface touch panel
Over 300 cd/m
Advanced thermal and air-flow design
Supports panel, wall, stand and arm mounting
M models support 9~36V DC power input for mobile application
Long product life support
RoHS compliant
Analog resistive type touch panel
1.3 External Overview
The ISDM series industrial monitors are durable devices that can be used in harsh
industrial environments. The following sections describe the physical layout of the ISDM
series industrial monitors.
2
high brightness and 50,000 hrs MTFB long lifetime panel
Page 21
Page 22
1.3.1 Front View
The front of the ISDM series industrial monitor is a flat panel TFT LCD screen surrounded
ISDM Series Industrial Monitor
by a stainless steel frame (
Figure 1-1: ISDM Series Front View
Figure 1-1).
1.3.2 Bottom Panel View
Figure 1-2 shows the bottom panel of the ISDM-104 monitor. Other models may include
or exclude additional connectors. Refer to Section
connectors. All connectors are fully described in Section
2.3 for listings of monitors and their
5.4.
Figure 1-2: Typical Bottom Panel View
Page 22
Page 23
ISDM Series Industrial Monitor
1.3.3 AD Board
The ISDM series industrial monitor AD board provides a wide variety of control interfaces,
receiving and managing signals from a CPU card through cabling.
AV-5300 AD board as a sample of a typical AD board for the ISDM series industrial
monitor. Refer to Chapter
4 for a complete description of AD boards and their connectors.
Figure 1-3 shows the
Figure 1-3: AV-5300 AD Board
1.4 Series Specifications
Table 1-2 shows the ISDM Series specifications.
Page 23
Page 24
ISDM Series Industrial Monitor
Model ISDM-084G ISDM-104G ISDM-121G ISDM-121GX
LCD Size 8.4" 10.4" 12.1" 12.1" 15" 17" 19"
Input
Interface
Max.
Resolution
Brightness
(cd/m2)
Contrast 450:1 500:1 500:1 700:1 400:1 500:1 700:1
LCD Color 262K 262K 262K 262K 262K 16.2M 16.2M
Pixel Pitch (mm) 0.213 0.264 0.3075 0.240 0.297 0.264 0.294
Front Frame
Chassis
View Angle
(H / V)
VGA VGA
800x600 800x600 800x600 1024x768 1024x768 1280x1024 1280x1024
400 400 400 450 350 300 300
Stainless
steel
Heavy-duty
steel
120/100 120/100 140/110 160/160 120/100 140/130 140/130
Stainless
steel
Heavy-duty
steel
VGA
DVI-D
Stainless
steel
Heavy-duty
steel
VGA
DVI-D
Stainless
steel
Heavy-duty
steel
ISDM-150G ISDM-170G ISDM-190G
VGA
DVI-D
Stainless
steel
Heavy-duty
steel
VGA
DVI-D
Stainless
steel
Heavy-duty
steel
VGA
DVI-D
Stainless
steel
Heavy-duty
steel
AD Board AV-5350 AV-5350 AV-5300 AV-5300 AV-5300 AV-5300 AV-5300
Power Adapter 25W 25W 45W 45W 45W 45W 45W
OSD function Yes Yes Yes Yes Yes Yes Yes
Panel
Wall
Mounting
Arm
Stand
Back Cover Color Silver Silver Silver Silver Silver Silver Silver
244 x
Dimension
178 x
(WxHxD) (mm)
49
Operation
0~50°C 0~50°C 0~50°C 0~50°C 0~50°C 0~50°C 0~50°C
Temperature
IP Level IP 65 IP 65 IP 65 IP 65 IP 65 IP 65 IP 65
N/G Weight 2.3kg 3.4kg 4.4kg 4.4kg 6.6kg 9.2kg 10.75kg
Panel
Wall
Arm
Stand
311.5 x
242 x
52.1
Panel
Wall
Arm
Stand
340 x
260 x
58
Panel
Wall
Arm
Stand
340 x
260 x
58
Panel
Wall
Arm
Stand
409.25 x
308.25 x
63.2
Panel
Wall
Arm
Stand
452.0 x
356.0 x
63.2
Panel
Wall
Arm
Stand
482.6 x
399.3 x
71.6
Page 24
Page 25
ISDM Series Industrial Monitor
Table 1-2: ISDM Series Specifications
1.5 Certifications
All ISDM series industrial monitor models comply with the following international
standards:
RoHS
IP 65
For a more detailed description of these standards, please refer to Appendix
B.
Page 25
Page 26
ISDM Series Industrial Monitor
Chapter
2
2 Mechanical Overview
Page 26
Page 27
ISDM Series Industrial Monitor
2.1 Introduction
This chapter describes the general mechanical overview of the ISDM series monitors
including front and bottom panel variations, available interfaces and overall dimensions.
2.2 Front Panel
The front panel of the ISDM series industrial monitor is comprised of a TFT LCD in an
stainless steel frame.
Figure 2-1: Front Panel
2.3 Rear Panel
The OSD control panel is located on the rear panel of the ISDM series industrial monitor
(
Figure 2-2). The rear panel also contains four retention screw holes (circled in Figure 2-2 )
for mounting the monitor to a wall.
Page 27
Page 28
ISDM Series Industrial Monitor
Figure 2-2: Rear Panel
2.4 Bottom Panel
All peripheral device connectors are located on the bottom panel of the ISDM series
industrial monitor. The following sections describe the bottom panel variants and their
associated connectors.
2.4.1 Available Connectors
There are a number of bottom panel peripheral device connectors available for the ISDM
series industrial monitor.
VGA connector
DVI-D connector
12V power connector
9~36V terminal block
RS-232 serial connector
USB connector
2.4.2 ISDM-084 Connectors
The following is a list of the bottom panel peripheral device connectors used on the
ISDM-084 series industrial monitor.
Page 28
Page 29
ISDM Series Industrial Monitor
VGA connector
12V power connector
RS-232 serial connector
9~36V terminal block (M models only)
2.4.3 ISDM-104 Connectors
The following is a list of the bottom panel peripheral device connectors used on the
ISDM-104 series industrial monitor.
VGA connector
12V power connector
RS-232 serial connector
9~36V terminal block (M models only)
2.4.4 ISDM-121 Connectors
The following is a list of the bottom panel peripheral device connectors used on the
ISDM-121 series industrial monitor.
VGA connector
DVI-D connector
12V power connector
9~36V terminal block (M models only)
RS-232 serial connector (T-R models only)
USB connector (USB/T-R models only)
2.4.5 ISDM-150 Connectors
The following is a list of the bottom panel peripheral device connectors used on the
ISDM-150 series industrial monitor.
VGA connector
DVI-D connector
12V power connector
9~36V terminal block (M models only)
RS-232 serial connector (T-R models only)
Page 29
Page 30
USB connector (USB/T-R models only)
2.4.6 ISDM-170 Connectors
The following is a list of the bottom panel peripheral device connectors used on the
ISDM-170 series industrial monitor.
VGA connector
DVI-D connector
12V power connector
9~36V terminal block (M models only)
RS-232 serial connector (T-R models only)
USB connector (USB/T-R models only)
2.4.7 ISDM-190 Connectors
ISDM Series Industrial Monitor
The following is a list of the bottom panel peripheral device connectors used on the
ISDM-190 series industrial monitor.
VGA connector
DVI-D connector
12V power connector
9~36V terminal block (M models only)
RS-232 serial connector (T-R models only)
USB connector (USB/T-R models only)
Page 30
Page 31
ISDM Series Industrial Monitor
2.5 Physical Dimensions
The following sections describe the physical dimensions for each model of the ISDM
series industrial monitor.
2.5.1 General Physical Dimensions
General physical dimensions for the ISDM series industrial monitors are shown in Table
2-1.
Model
ISDM-190 482.6 399.3 71.6
ISDM-170 452 356 63.2
ISDM-150 409.25 308.25 63.2
ISDM-121 340 260 58
ISDM-104 311.5 242 52.1
ISDM-084 244 178 49
Table 2-1: General Physical Dimensions
Width
(mm)
Height
(mm)
Depth
(mm)
2.5.2 ISDM-190 Physical Dimensions
The physical dimensions of the ISDM-190 are shown in Figure 2-3.
Page 31
Page 32
ISDM Series Industrial Monitor
Figure 2-3: ISDM-190 Physical Dimensions (millimeters)
Page 32
Page 33
ISDM Series Industrial Monitor
2.5.3 ISDM-170 Physical Dimensions
The physical dimensions of the ISDM-170 are shown in Figure 2-4.
Figure 2-4: ISDM-170 Physical Dimensions (millimeters)
Page 33
Page 34
2.5.4 ISDM-150 Physical Dimensions
The physical dimensions of the ISDM-150 are shown in Figure 2-5.
ISDM Series Industrial Monitor
Page 34
Figure 2-5: ISDM-150 Physical Dimensions (millimeters)
Page 35
ISDM Series Industrial Monitor
2.5.5 ISDM-121 Physical Dimensions
The physical dimensions of the ISDM-121 are shown in Figure 2-6.
Figure 2-6: ISDM-121 Physical Dimensions (millimeters)
Page 35
Page 36
2.5.6 ISDM-104 Physical Dimensions
The physical dimensions of the ISDM-104 are shown in Figure 2-7.
ISDM Series Industrial Monitor
Page 36
Figure 2-7: ISDM-104 Physical Dimensions (millimeters)
Page 37
ISDM Series Industrial Monitor
2.5.7 ISDM-084 Physical Dimensions
The physical dimensions of the ISDM-084 are shown in Figure 2-8.
Figure 2-8: ISDM-084 Physical Dimensions (millimeters)
Page 37
Page 38
2.6 Optional Mounting Kits
The following sections describe the various optional mounting kits available for each
ISDM Series Industrial Monitor
model of the ISDM series industrial monitor. Refer to Section
5.5 for detailed instructions
on the different mounting methods for the monitors.
2.6.1 ISDM-084 Mounting Kits
Table 2-2 lists the mounting kits available for the ISDM-084 monitor.
Model ISDM-084
Panel Mounting Kit PK-084M
Wall Mounting Kit WK-084MS-R10
LCD Monitor Arm ARM-11-RS
LCD Monitor Stand STAND-100-RS
Table 2-2: ISDM-084 Mounting Kits
2.6.2 ISDM-104 Mounting Kits
Table 2-3 lists the mounting kits available for the ISDM-104 monitor.
Model ISDM-104
Panel Mounting Kit PK-104M
Wall Mounting Kit WK-104MS-R10
LCD Monitor Arm ARM-11-RS
LCD Monitor Stand STAND-100-RS
Table 2-3: ISDM-104 Mounting Kits
2.6.3 ISDM-121 Mounting Kits
Table 2-4 lists the mounting kits available for the ISDM-121 monitor.
Model ISDM-121
Panel Mounting Kit PK-121M
Wall Mounting Kit WK-121MS-R10
Page 38
Page 39
ISDM Series Industrial Monitor
LCD Monitor Arm ARM-11-RS
LCD Monitor Stand STAND-100-RS
Table 2-4: ISDM-121 Mounting Kits
2.6.4 ISDM-150 Mounting Kits
Table 2-5 lists the mounting kits available for the ISDM-150 monitor.
Model ISDM-150
Panel Mounting Kit PK-150M
Wall Mounting Kit WK-150MS-R10
LCD Monitor Arm ARM-31-RS
LCD Monitor Stand STAND-200-RS
Table 2-5: ISDM-150 Mounting Kits
2.6.5 ISDM-170 Mounting Kits
Table 2-6 lists the mounting kits available for the ISDM-170 monitor.
Model ISDM-170
Panel Mounting Kit PK-170M
Wall Mounting Kit WK-170MS-R10
LCD Monitor Arm ARM-31-RS
LCD Monitor Stand STAND-200-RS
Table 2-6: ISDM-170 Mounting Kits
2.6.6 ISDM-190 Mounting Kits
Table 2-7 lists the mounting kits available for the ISDM-190 monitor.
Model ISDM-190
Panel Mounting Kit PK-190M
Wall Mounting Kit WK-190MS-R10
LCD Monitor Arm ARM-31-RS
Page 39
Page 40
LCD Monitor Stand STAND-200-RS
Table 2-7: ISDM-190 Mounting Kits
2.7 Mounting Options
Each ISDM series industrial monitor has a number of mounting holes or slots located on
the back side of the aluminum frame or on the rear panel for mounting the monitor to a
panel, wall, arm or stand. The following sections describe the various mounting methods
ISDM Series Industrial Monitor
or each model of the ISDM series industrial monitor. Refer to Section
instructions on mounting the monitors.
5.5 for detailed
2.7.1 Panel Mounting
Each model of the ISDM series industrial monitor has a series of mounting slots located
on the top and bottom panel for mounting the monitor to a panel.
Figure 2-9 shows a typical panel installation.
Page 40
Figure 2-9: Typical Panel Mounting
Table 2-8 lists the number of mounting clamps required to mount the monitor to a panel.
Page 41
ISDM Series Industrial Monitor
Model Mounting Clamps
ISDM-190 14
ISDM-170 10
ISDM-150 10
ISDM-121 10
ISDM-104 10
ISDM-084 8
Table 2-8: Panel Mounting Clamps
2.7.2 Wall Mounting
Each model of the ISDM series industrial monitor has four holes located on the rear panel
for mounting the monitor to a wall.
Figure 2-10 shows the typical methods for wall mounting.
Figure 2-10: Typical Wall Mounting
Page 41
Page 42
2.7.3 Monitor Arm or Stand Mounting
Most models of the ISDM series industrial monitor have four or eight Video Electronics
Standards Association (VESA) standard holes located on the rear panel for mounting the
monitor to a monitor arm or stand.
NOTE:
There is no monitor stand available for the ISDM-190
monitor.
Figure 2-11 shows a typical monitor arm or stand mounting.
ISDM Series Industrial Monitor
Page 42
Figure 2-11: Typical Monitor Arm or Stand Mounting
Page 43
ISDM Series Industrial Monitor
THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 43
Page 44
ISDM Series Industrial Monitor
Chapter
3
3 LCD and Touch Panel
Specifications
Page 44
Page 45
ISDM Series Industrial Monitor
3.1 LCD Specifications
3.1.1 LCD Overview
The ISDM series industrial monitors use the following LCD panels.
ISDM-190: AUO M190EG02
ISDM-170: AUO M170EG01
ISDM-150: AUO G150XG01
ISDM-121: AUO G121SN01
ISDM-121GX: CHI MEI G121X1-L01
ISDM-104: AUO G104SN03/ Toshiba LTA104D182F
ISDM-084: AUO G084SN03/ Toshiba LTA084C270F
Detailed specifications for the LCD screens are listed in the following sections.
Page 45
Page 46
3.1.2 ISDM-190 LCD Specifications
Table 3-1 lists the ISDM-190 LCD specifications.
Model ISDM-190
Size 19”
MFR/Model AUO/M190EG02
Resolution SXGA (1280 x 1024)
Active Area (mm) 376.3 x 301.1
Pixel Pitch (mm) 0.294
Mode TN
Number of Colors 16.2M
Color Saturation (NTSC%) 72
View Angle (H/V) 160 / 160
ISDM Series Industrial Monitor
Brightness (cd/m2) 300
Contrast Ratio 700:1
Response Time (ms) (at 25C) 6
Power Consumption (W) 28
Interface 2ch LVDS
Supply Voltage (V) 5
Backlight 4 CCFL
Lamp Life (hrs) 50,000
Table 3-1: ISDM-190 LCD Specifications
Page 46
Page 47
ISDM Series Industrial Monitor
3.1.3 ISDM-170 LCD Specifications
Table 3-2 lists the ISDM-170 LCD specifications.
Model ISDM-170
Size 17"
MFR/Model AUO/M170EG01
Resolution SXGA (1280 x 1024)
Active Area (mm) 337.9 x 270.3
Pixel Pitch (mm) 0.264
Mode TN
Number of Colors 16.2M
Color Saturation (NTSC%) 72
View Angle (H/V) 140/130
Brightness (cd/m2) 300
Contrast Ratio 500:1
Response Time (ms) (at 25C) 8
Power Consumption (W) 25.8
Interface 2ch LVDS
Supply Voltage (V) 5
Backlight 4 CCFL
Lamp Life (hrs) 50,000
Table 3-2: ISDM-170 LCD Specifications
Page 47
Page 48
3.1.4 ISDM-150 LCD Specifications
Table 3-3 lists the ISDM-150 LCD specifications.
Model ISDM-150
Size 15"
MFR/Model AUO/G150XG01
Resolution XGA (1024 x 768)
Active Area (mm) 304.1 x 228.1
Pixel Pitch (mm) 0.297
Mode TN
Number of Colors 262K
Color Saturation (NTSC%) 60
ISDM Series Industrial Monitor
View Angle (H/V) 130/120
Brightness (cd/m2) 350
Contrast Ratio 500:1
Response Time (ms) (at 25C) 12
Power Consumption (W) 11.5
Interface 1ch LVDS
Supply Voltage (V) 3.3
Backlight 2 CCFL
Lamp Life (hrs) 50000
Table 3-3: ISDM-150 LCD Specifications
Page 48
Page 49
ISDM Series Industrial Monitor
3.1.5 ISDM-121 LCD Specifications
Table 3-4 lists the ISDM-121 LCD specifications.
Model ISDM-121G ISDM-121GX
Size 12.1” 12.1”
MFR/Model AUO/G121SN01 CHE MEI/G121X1-L01
Resolution SVGA (800 x 600) XGA (1024 x 768)
Active Area (mm) 246.0 x 184.5 245.76 x 184.32
Pixel Pitch (mm) 0.307 0.240
Mode TN TN
Number of Colors 262K 262K
View Angle (H/V) 140/110 160/160
Brightness (cd/m2) 400 450
Contrast Ratio 500:1 700:1
Response Time (ms) (at 25C) 35 13 (TR); 12 (TF)
Power Consumption (W) 7.3 3.76
Interface 1ch LVDS 1ch LVDS
Supply Voltage (V) 3.3 5.0
Backlight 2 CCFL 2 CCFL
Lamp Life (hrs) 50000 50000
Table 3-4: ISDM-121 LCD Specifications
Page 49
Page 50
3.1.6 ISDM-104 LCD Specifications
Table 3-5 lists the ISDM-104 LCD specifications.
ISDM-104 Model G/GM Model GH/GHM Model
Size 10.4” 10.4”
MFR/Model AUO/G104SN03 Toshiba/LTA104D182F
ISDM Series Industrial Monitor
Resolution SVGA (800 x 600)
Active Area (mm) 211.2 x 158.4 211.2 x 158.4
Pixel Pitch (mm) 0.264 0.264
Mode TN TN
Number of Colors 262K 262K
View Angle (H/V) 120 / 100 120 / 100
Brightness (cd/m2) 230 400
Contrast Ratio 500:1 500:1
Response Time (ms) (at 25C) 35 6 (tON), 17 (t
Interface 1ch LVDS 1ch LVDS
Supply Voltage (V) 3.3 3.3
Backlight 1 CCFL 2 CCFL
Lamp Life (hrs) 20000 50000
SVGA (800 x 600)
)
OFF
Table 3-5: ISDM-104 LCD Specifications
Page 50
Page 51
ISDM Series Industrial Monitor
3.1.7 ISDM-084 LCD Specifications
Table 3-6 lists the ISDM-084 LCD specifications.
ISDM-084 Model GH/GHM Models
Size 8.4”
MFR/Model Toshiba/LTA084C270F
Resolution SVGA (800 x 600)
Active Area (mm) 170.4 x 127.8
Pixel Pitch (mm) 0.213
Mode TN
Number of Colors 262K
View Angle (H/V) 120 / 100
Brightness (cd/m2) 400
Contrast Ratio 450:1
Response Time (ms) (at 25C) 8 (tON), 17 (t
Interface 1ch LVDS
Supply Voltage (V) 3.3
Backlight 2 CCFL
Lamp Life (hrs) 50000
OFF
)
Table 3-6: ISDM-084 LCD Specifications
Page 51
Page 52
3.2 Touch Panels
IEI offers touch panels for the ISDM series industrial monitors with the following features:
Small border customized design
All size touch panel design
Customized activation force and palm rejection
Customized optical characteristics
High reliability and durability in the field
3.2.1 Touch Panel Models
Table 3-7 lists the ISDM series industrial monitors and their associated touch panels.
Model Touch Panel
ISDM Series Industrial Monitor
ISDM-190 PanJit 1190503A
ISDM-170 PanJit 1171505A
ISDM-150 PanJit 1150508B
ISDM-121 PanJit 1121505B
ISDM-104 PanJit 1104502A
ISDM-084 PanJit 1084403B
Table 3-7: Touch Panel Models
Page 52
Page 53
ISDM Series Industrial Monitor
3.2.2 Touch Panel Dimensions
Table 3-8 shows the touch panel dimensions in millimeters.
Model: Dimension
Dimensional Outline: 330 404.6 2.8
PanJit
1190503A
PanJit
1171505A
PanJit
1150508B
PanJit
1121505B
PanJit
1104502A
Viewing Area: 306.05
Active Area: 301.05
Key Area: 300.05
Dimensional Outline: 365 295.08 2.9
Viewing Area: 342.05
Active Area: 342.05
Key Area: 338.0 271.4 -
Dimensional Outline: 257.5 333.6 2.9
Viewing Area: 232.1 308.2 -
Active Area: 228.1 304.1 -
Dimensional Outline: 204 268 2.1
Viewing Area: 188 250 -
Active Area: 185 246 -
Dimensional Outline: 238.8 188.7 2.6
Viewing Area: 219.8 166.8 -
Active Area: 212.1 159.3 -
Width Length Thick
381.3 -
376.3 -
375.3 -
275.45 -
275.45 -
PanJit
Dimensional Outline: 145.53
Viewing Area: 130.75
1084403B
Active Area: 127.78
Dimensional Outline: 150.00
PanJit
Viewing Area: 139.00
1065403C
Active Area: 133.00
188.04 2.1
173.38 -
170.38 -
117.50 2.1
106.00 -
99.80 -
Table 3-8: Touch Panel Dimensions (mm)
Page 53
Page 54
3.2.3 Touch Panel Specifications
Table 3-9 lists the touch panel specifications.
Type Analog Resistive Type Touch Panel
Input Method Finger, Stylus or gloved hand
Wire Type 5-wire/4-wire
Maximum Voltage and Currant DC7V
Position Accuracy Less than 1.5%
Isolation ≥20M ohm
Resolution 4096 x 4096 dpi based on controller resolution
Activation Force Typical: less than 100g
Controller Interface RS-232 or USB 1.1
ISDM Series Industrial Monitor
Optional: custom activation force and palm rejection
Light Transmission Anti-glare type: 78% - 90%
Temperature (Typical) Operating: -10°C to 60°C
Storage: -20°C to 70°C
Relative Humidity Operating: 20% to 90%RH
Storage: 20% to 90%RH
Electrostatic Protection Touch Panel: 30KV (Contact/Air)
Controller: 20KV (Contact/Air)
Surface Hardness 3H and above per LIS K5400
Life (Hitting) More than 10 million for 5-wire touch panel
Life (Drawing) More than 300 K alphabets for 5-wire touch panel
OS Compatibility Windows: XP/XP Embedded/2000/ME
Windows 98 SE
Windows CE.Net 4.2 (x86 and ARM)
WHQL certified
Linux: Fedora Core I/II
Mandrake 10.0/10.1
Page 54
RedHat 9.0
Table 3-9: Touch Panel Specifications
Page 55
ISDM Series Industrial Monitor
3.2.4 Touch Panel RS-232 Controller Specifications
Table 3-10 lists the touch panel RS-232 controller specifications.
Circuit Board
Dimension
Power Requirements D.C.+5V (100mA typical, 50mV peak to peak
Operating
Temperature
Storage Temperature -40°C to 80°C
Relative Humidity 95% at 60°C
Interface Bi-directional RS-232 serial communication
Protocol No parity, 8 data bits, 1 stop bit,
Resolution 2048x2048
Report Rate Max. 160 points/sec
Response Time Max. 35 ms
Attached Cable 6' shielded cable with 9-pin D-sub connector
Regulatory Approvals FCC-B, CE, Unaffected by EMI from other nearby
20mm x 75mm (0.79inches x
2.95inches)----(5-Wire)
maximum ripple and noise)
0°C to 50°C
9600 baud (N,8,1,9600)
CRTs and other display devices
EMI Unaffected by environmental EMI
Panel Resistance 5 wire resistive model: 50 ~ 200 ohm
Table 3-10: Touch Panel RS-232 Controller Specifications
Page 55
Page 56
3.2.5 Touch Panel USB Controller Specifications
Table 3-11 lists the touch panel USB controller specifications.
ISDM Series Industrial Monitor
Circuit Board
Dimension
Power Requirements D.C.+5V (100mA typical, 50mV peak to peak
Operating
Temperature
Storage Temperature -40°C to 80°C
Relative Humidity 95% at 60°C
Interface USB 1.1 Low Speed
Protocol No parity, 8 data bits, 1 stop bit,
Resolution 2048 x 2048
Report Rate Max. 160 points/sec
Response Time Max. 35 ms
Attached Cable 6' shielded cable with USB-A connector for USB port
Regulatory Approvals FCC-B, CE, Unaffected by EMI from other nearby
20mm x 75mm (0.79inches x
2.95inches)----(5-Wire)
maximum ripple and noise)
0°C to 50°C
9600 baud (N,8,1,9600)
Page 56
CRTs and other display devices
EMI Unaffected by environmental EMI
Panel Resistance 5 wire resistive model: 50 ~ 200 ohm
Table 3-11: Touch Panel USB Controller Specifications
Page 57
ISDM Series Industrial Monitor
3.3 Power Adapters
Table 3-12 lists the AC/DC power adapter specifications.
Model ISDM-190, ISDM-170, ISDM-150,
ISDM-121
Power 45 Watt AC/DC Adapter 25 Watt AC/DC Adapter
General Description Universal Input 90 to 264 VAC
EMI Meets FCC/CISPR 22 Class B
MTBF 165Khrs
Limited Power Source
Input Voltage Range 90-264VAC 90-264VAC
Input Frequency 47-63 Hz 47-63 Hz
Inrush Current 40A max. (Cold Start) 30A max. (Cold Start)
Hold-up Time 10mS typical 10mS typical
Leakage Current 0.5mA max. 3.5mA max.
Short Circuit Protection Continuous Continuous
Over-voltage Protection Yes Yes
Continuous Output
Power
45W max. 25W max.
ISDM-104, ISDM-084
Universal Input 90 to 264 VAC
EMI Meets FCC/CISPR 22 Class B
MTBF 300Khrs
Limited Power Source
Hi-pot Isolation:
Input / Output
4242VDC 4242VDC
Table 3-12: Power Adapter Specifications
Page 57
Page 58
ISDM Series Industrial Monitor
Chapter
4
4 AD Boards
Page 58
Page 59
ISDM Series Industrial Monitor
4.1 AD Board Overview
The ISDM series industrial monitor AD board provides a wide variety of control interfaces,
receiving and managing interface signals from a CPU card through cabling. There are two
AD boards used for the ISDM series monitors: AV-5350 and AV-5300. Refer to
for a listing of ISDM series monitors and their associated AD board. The following sections
describe each AD board in detail.
4.2 AV-5350 AD Board
The following sections describe the AV-5350 AD board in detail.
4.2.1 AV-5350 AD Board Overview
Table 1-2
Figure 4-1: AV-5350 AD Board Overview
4.2.2 AV-5350 AD Board Connectors
The AV-5350 AD board has the following connectors on-board:
Page 59
Page 60
1 x VGA connector
1 x External OSD and LED Indication connector
1 x LVDS connector
3 x 5V power connector
1 x Backlight Inverter connector
ISDM Series Industrial Monitor
The AV-5350 AD board has the following connectors on the board rear panel:
1 x VGA connector
1 x 12V DC power connector
The locations of the peripheral interface connectors for the AV-5350 AD board are shown
in Section
Section
4.2.3. A complete list of all the peripheral interface connectors can be seen in
4.2.4.
4.2.3 AV-5350 AD Board Layout
Figure 4-2 shows the on-board peripheral connectors and on-board jumpers.
Page 60
Figure 4-2: Connector and Jumper Locations
Page 61
ISDM Series Industrial Monitor
4.2.4 AV-5350 Peripheral Interface Connectors
Table 4-1 shows a list of the peripheral interface connectors on the AV-5350 AD board.
Detailed descriptions of these connectors can be found in Section
Connector Type Label
5V Power connector 2-pin header CN7, CN8, CN9
Backlight Inverter connector 6-pin header CN6
External OSD and
9-pin header CN2
LED Indication connector
LVDS Output connector 30-pin header CN5
VGA connector 10-pin header J2
Table 4-1: AV-5350 Peripheral Interface Connectors
4.2.7.
4.2.5 AV-5350 Rear Panel Connectors
Table 4-2 lists the rear panel connectors and jumpers on the AV-5350 AD board. Detailed
descriptions of these connectors and jumpers can be found in Section
Connector Type Label
DC 12V Power connector DC Power Jack J3
VGA Connector 15-pin VGA connector J1
Table 4-2: AV-5350 Rear Panel Connectors
4.2.13.
Page 61
Page 62
4.2.6 AV-5350 On-board Jumper
Table 4-3 lists the on-board jumper. A detailed description of the jumper can be found in
ISDM Series Industrial Monitor
Section
Jumper Type Label
LCD Panel Voltage Select 3-pin header JP1
Table 4-3: AV-5350 On-board Jumper
4.2.16.
4.2.7 AV-5350 Internal Peripheral Connectors
Internal peripheral connectors on the AV-5350 AD board are only accessible when the
board is outside of the monitor. This section has complete descriptions of all the internal,
peripheral connectors on the AV-5350 AD board.
4.2.8 5V Power Connector
CN Label: CN7, CN8, CN9
CN Type:
2-pin header
Page 62
CN Pinouts: See
CN Location: See
The 5V power connector is a general-purpose power connector.
PIN DESCRIPTION PIN DESCRIPTION
1 +5V 2 GND
Table 4-4: 5V Power Connector Pinouts
Table 4-4
Figure 4-3
Page 63
ISDM Series Industrial Monitor
Figure 4-3: 5V Power Connector Location
4.2.9 Backlight Inverter Connector
CN Label: CN6
CN Type:
CN Pinouts: See
CN Location: See
The Inverter connector connects to the LCD backlight.
PIN DESCRIPTION
1 +12V
2 +12V
3 On/Off
4 BKLT_ADJ
5 GND
6-pin header
Table 4-5
Figure 4-4
6 GND
Table 4-5: Backlight Inverter Connector Pinouts
Page 63
Page 64
ISDM Series Industrial Monitor
Figure 4-4: Backlight Inverter Connector Location
4.2.10 External OSD and LED Indication Connector
CN Label: CN2
9-pin header
Table 4-6
Figure 4-5
Page 64
CN Type:
CN Pinouts: See
CN Location: See
The External OSD and LED Indication connector connects to an external OSD controller.
Page 65
ISDM Series Industrial Monitor
PIN DESCRIPTION
1 LED_ORANGE
2 +5V
3 LED_GREEN
4 MENU/ENTER
5 RIGHT
6 LEFT
7 AUTO
8 LCD ON/OFF
9 GND
Table 4-6: External OSD and LED Indication Connector Pinouts
Figure 4-5: External OSD and LED Indication Connector Location
Page 65
Page 66
4.2.11 LVDS Output Connector
CN Label: CN7
ISDM Series Industrial Monitor
CN Type:
CN Pinouts: See
CN Location: See
30-pin header
Table 4-7
Figure 4-6
Use the LVDS output connector to connect the LCD panel to a system.
PIN DESCRIPTION PIN DESCRIPTION
1 GND 2 GND
3 TXO3+ 4 TXO3-
5 TXOC+ 6 TXOC-
7 TXO2+ 8 TXO2-
9 TXO1+ 10 TXO1-
11 TXO0+ 12 TXO0-
13 GND 14 GND
15 TXE3+ 16 TXE3-
17 TXEC+ 18 TXEC-
19 TXE2+ 20 TXE2-
21 TXE1+ 22 TXE1-
23 TXE0+ 24 TXE0-
25 GND 26 GND
27 VDD 28 VDD
29 VDD 30 VDD
Table 4-7: LVDS Output Connector Pinouts
Page 66
Page 67
ISDM Series Industrial Monitor
Figure 4-6: LVDS Output Connector Location
NOTE:
The supply voltage (3.3V (Default), 5V or 12V) can be selected via JP1.
4.2.12 VGA Connector
CN Label: J2
CN Type:
CN Pinouts: See
CN Location: See
10-pin header
Table 4-8
Figure 4-7
In addition to the standard DB-15 female VGA connector (J1), a VGA connection can also
be made through the on-board CN2 10-pin header.
Page 67
Page 68
ISDM Series Industrial Monitor
PIN DESCRIPTION PIN DESCRIPTION
1 RED 2 DDCCLK
3 GREEN 4 DDCDAT
5 BLUE 6 GROUND
7 HSYNC 8 GROUND
9 VSYNC 10 GROUND
Table 4-8: VGA Connector Pinouts
Figure 4-7: VGA Connector Location
4.2.13 AV-5350 External (Rear Panel) Connectors
Figure 4-8 shows the AV-5350 external (rear panel) connectors. The peripheral
connectors on the back panel of the monitor can connect to external devices. The
peripheral connectors on the rear panel are:
1 x DC 12V connector
1 x VGA connector
Page 68
Page 69
ISDM Series Industrial Monitor
Figure 4-8: AV-5350 External (Rear Panel) Connectors
4.2.14 DC 12V Connector
CN Label: J3
CN Type:
CN Pinouts: See
CN Location: See
Use the DC 12V connector to power the monitor.
PIN DESCRIPTION
1 GND
2 GND
3 DC 12V
Table 4-9: DC 12V Connector Pinouts
DC 12V Jack
Table 4-9
Figure 4-8
4.2.15 VGA Connector
CN Label: J1
CN Type:
CN Pinouts: See
CN Location:
Use the standard HD-D-sub 15-pin VGA connector to connect the monitor to a system.
HD-D-sub 15 female connector
Table 4-10 and Figure 4-9
Figure 4-8
Page 69
Page 70
p
p
PIN DESCRIPTION PIN DESCRIPTION
1 Red 9 No Connect
2 Green 10 Ground
3 Blue 11 No Connect
4 No Connect 12 DDC DAT
5 Ground 13 Horizontal Synchronization
6 Ground 14 Vertical Synchronization
7 Ground 15 DDC Clock
8 Ground
Table 4-10: VGA Connector Pinouts
ISDM Series Industrial Monitor
Figure 4-9: VGA Connector Pinout Locations
4.2.16 AV-5350 On-board Jumper
NOTE:
A jumper is a metal bridge used to close an
electrical circuit. It consists of two or three metal
ins and a small metal clip (often protected by a
lastic cover) that slides over the pins to
connect them. To CLOSE/SHORT a jumper
means connecting the pins of the jumper with
the plastic clip and to OPEN a jumper means
removing the plastic clip from a jumper.
Figure 4-10: Jumpers
The AV-5350 has one on-board jumper (Table 4-3).
Page 70
Page 71
ISDM Series Industrial Monitor
Figure 4-11: Jumper Location
4.2.17 LCD Panel Voltage Select Jumper
Jumper Label: JP5
Jumper Type:
Jumper Location: See
Jumper Settings: See
The JP1 jumper sets the voltage to the LCD panel.
JP1 Description
1-2 Panel Voltage select 3.3V (Default)
3-4 Panel Voltage select 5V
6-pin header
Figure 4-11
Table 4-11
5-6 Panel Voltage select 12V
Table 4-11: LCD Panel Voltage Select Jumper Settings
Page 71
Page 72
4.3 AV-5300 AD Board Overview
The AV-5300 AD board provides a wide variety of control interfaces, receiving and
managing interface signals from a CPU card through cabling. The following sections
describe the AV-5300 AD board in detail.
ISDM Series Industrial Monitor
Page 72
Figure 4-12: AV-5300 AD Board Overview
Page 73
ISDM Series Industrial Monitor
4.3.1 AV-5300 AD Board Connectors
The AV-5300 AD board has the following connectors on-board:
1 x Auto-dimming connector
1 x Debug connector
1 x External OSD and LED Indication connector
1 x Inverter interface connector
1 x LVDS connector
2 x Power output connector
2 x Power input connector
1 x VGA connector
The AV-5300 AD board has the following connectors on the board rear panel:
1 x 12V DC power connector
1 x DVI connector
1 x VGA connector
The locations of the peripheral interface connectors for the AV-5300 AD board are shown
in Section
Section
4.3.2. A complete list of all the peripheral interface connectors can be seen in
4.3.3.
Page 73
Page 74
4.3.2 AV-5300 AD Board Layout
Figure 4-13 shows the on-board peripheral connectors and on-board jumpers.
ISDM Series Industrial Monitor
Page 74
Figure 4-13: Connector and Jumper Locations
Page 75
ISDM Series Industrial Monitor
4.3.3 AV-5300 Peripheral Interface Connectors
Table 4-12 shows a list of the peripheral interface connectors on the AV-5300 AD board.
Detailed descriptions of these connectors can be found in Section
Connector Type Label
Auto-dimming connector 6-pin wafer
connector
Debug connector 4-pin wafer
connector
External OSD and LED Indication connector 9-pin wafer
connector
Inverter interface connector 6-pin wafer
connector
LVDS connector 30-pin connector CN8
Power output connectors 2-pin wafer
connector
4.3.6.
CN16
CN4
CN3
CN2
CN12, CN13
Power input connectors 3-pin wafer
VGA connector 10-pin box header J1
Table 4-12: AV-5300 Peripheral Interface Connectors
4.3.4 AV-5300 Rear Panel Connectors
Table 4-13 lists the rear panel connectors on the AV-5300 AD board. Detailed
descriptions of these connectors can be found in Section
CN24. CN25
connector
4.3.18.
Page 75
Page 76
Connector Type Label
12V DC power connector DC Power Jack J3
DVI connector 24-pin DVI-D connector J2
VGA connector 15-pin VGA connector J5
Table 4-13: AV-5300 Rear Panel Connectors
4.3.5 AV-5300 On-board Jumpers
Table 4-14 lists the on-board jumpers. A detailed description of these jumpers can be
ISDM Series Industrial Monitor
found in Section
Jumper Type Label
LCD Panel Power Input Select 6-pin header JP4
LCD Panel Voltage Select 6-pin header JP1
Table 4-14: AV-5300 On-board Jumpers
4.3.15.
4.3.6 AV-5300 Internal Peripheral Connectors
Internal peripheral connectors on the AV-5300 AD board are only accessible when the
board is outside of the monitor. This section has complete descriptions of all the internal,
peripheral connectors on the AV-5300 AD board.
4.3.7 Auto-Dimming Connector
CN Label: CN16
Page 76
CN Type: 6-pin wafer connector
CN Pinouts: See
CN Location: See
The auto-dimming connector connects to an external auto-dimming sensor.
Table 4-15
Figure 4-14
Page 77
ISDM Series Industrial Monitor
PIN DESCRIPTION
1 +3.3V
2 NC
3 GND
4 SCL
5 NC
6 SDA
Table 4-15: Auto-dimming Connector Pinouts
Figure 4-14: Auto-dimming Connector Location
4.3.8 Debug Port Connector
CN Label: CN4
CN Type: 4-pin wafer connector
CN Pinouts: See
CN Location: See
Use the debug port connector to update the AD board BIOS.
PIN DESCRIPTION
1 +5V
Table 4-16
Figure 4-15
Page 77
Page 78
2 TX
3 RX
4 GND
ISDM Series Industrial Monitor
Table 4-16: Debug Port Connector Pinouts
Figure 4-15: Debug Port Connector Location
4.3.9 External OSD and LED Indication Connector
CN Label: CN3
CN Type: 9-pin wafer connector
CN Pinouts: See
CN Location: See
The External OSD and LED Indication connector connects to an external OSD controller.
PIN DESCRIPTION
1 LED_ORANGE
2 LED_SENSOR
3 LED_GREEN
4 MENU/ENTER
5 RIGHT
Table 4-17
Figure 4-16
Page 78
6 LEFT
7 AUTO/EXIT
8 LCD ON/OFF
Page 79
ISDM Series Industrial Monitor
9 GND
Table 4-17: External OSD and LED Indication Connector Pinouts
Figure 4-16: External OSD and LED Indication Connector Location
4.3.10 Backlight Inverter Connector
CN Label: CN2
CN Type: 6-pin wafer connector
CN Pinouts: See
CN Location: See
The Inverter connector connects to the LCD backlight. Using the BKLT_EN signal to
control the inverter status (ON/OFF) and the BKLT_ADJ signal to adjust brightness of
inverter by OSD brightness function. The OSD brightness function can control a PWM
input and variable DC voltage to minimize flickering (due to the interference between
panel timing and inverter’s AC timing), and adjust LCD back light brightness.
PIN DESCRIPTION
1 +12V
Table 4-18
Figure 4-17
2 +12V
3 BKLT_EN
4 BKLT_ADJ
5 GND
Page 79
Page 80
6 GND
ISDM Series Industrial Monitor
Table 4-18: Backlight Inverter Connector Pinouts
Figure 4-17: Backlight Inverter Connector Location
4.3.11 LVDS Output Connector
CN Label: CN8
CN Type: 30-pin connector
CN Pinouts: See
CN Location: See
Use either LVDS output connector to connect the LCD panel to a system.
PIN DESCRIPTION PIN DESCRIPTION
1 GND 2 GND
3 TXO3+ 4 TXO3-
5 TXOC+ 6 TXOC-
7 TXO2+ 8 TXO2-
9 TXO1+ 10 TXO1-
Table 4-19
Figure 4-18
Page 80
11 TXO0+ 12 TXO0-
13 GND 14 GND
15 TXE3+ 16 TXE3-
Page 81
ISDM Series Industrial Monitor
PIN DESCRIPTION PIN DESCRIPTION
17 TXEC+ 18 TXEC-
19 TXE2+ 20 TXE2-
21 TXE1+ 22 TXE1-
23 TXE0+ 24 TXE0-
25 GND 26 GND
27 VDD 28 VDD
29 VDD 30 VDD
Table 4-19: LVDS Output Connector Pinouts
Figure 4-18: LVDS Output Connector Location
NOTE:
The supply voltage (3.3V (Default), 5V or 12V) can be selected via JP1.
4.3.12 Power Output Connector
CN Label: CN12, CN13
CN Type: 2-pin wafer connector
Page 81
Page 82
ISDM Series Industrial Monitor
CN Pinouts: See Table 4-20 and Table 4-21
CN Location: See
Figure 4-19
The AV-5300 supports two power output connectors, one for 12V and the other for 5V.
PIN DESCRIPTION
1 +12V
2 GND
Table 4-20: Power Output Connector Pinouts (CN12)
PIN DESCRIPTION
1 +5V
2 GND
Table 4-21: Power Output Connector Pinouts (CN13)
Figure 4-19: Power Output Connector Locations
4.3.13 Power Input Connector
CN Label: CN24, CN25
Page 82
Page 83
ISDM Series Industrial Monitor
CN Type: 2-pin wafer connector, 3-pin wafer connector
CN Pinouts: See
CN Location: See
Table 4-22 and Table 4-23
Figure 4-20
The AV-5300 supports two internal power input connectors.
PIN DESCRIPTION
1 +12V
2 GND
Table 4-22: Power Input Connector Pinouts (CN24)
PIN DESCRIPTION
1 +12V Input
2 GND
3 +9V~36V to external power
module
Table 4-23: Power Input Connector Pinouts (CN25)
Figure 4-20: Power Input Connector Locations
Page 83
Page 84
4.3.14 VGA Connector
CN Label: J1
CN Type: 10-pin box header
ISDM Series Industrial Monitor
CN Pinouts: See
CN Location: See
In addition to the standard DB-15 female VGA connector (J1), a VGA connection can also
be made through the on-board CN2 10-pin header.
PIN DESCRIPTION PIN DESCRIPTION
1 RED 2 SMCLK
3 GREEN 4 SMDATA
5 BLUE 6 GROUND
7 HSYNC 8 GROUND
9 VSYNC 10 GROUND
Table 4-24: VGA Connector Pinouts
Table 4-24
Figure 4-21
Page 84
Figure 4-21: VGA Connector Location
Page 85
p
p
ISDM Series Industrial Monitor
4.3.15 AV-5300 On-board Jumpers
NOTE:
A jumper is a metal bridge used to close an
electrical circuit. It consists of two or three metal
ins and a small metal clip (often protected by a
lastic cover) that slides over the pins to
connect them. To CLOSE/SHORT a jumper
means connecting the pins of the jumper with
the plastic clip and to OPEN a jumper means
removing the plastic clip from a jumper.
The AV-5300 has two on-board jumpers (Table 4-14).
Figure 4-22: Jumpers
Figure 4-23: Jumper Locations
Page 85
Page 86
4.3.16 LCD Panel Power Input Jumper
Jumper Label: JP4
Jumper Type: 6-pin header
ISDM Series Industrial Monitor
Jumper Location:
Jumper Settings:
Figure 4-23
See
Table 4-25
See
The JP4 jumper sets the input source from either the 12V power connector (J3) or the
external terminal block.
JP4 Description
1-3, 2-4 +12V from power connector (J3) (Default)
3-5, 4-6
Input with external connector
(Need external power module)
Table 4-25: LCD Panel Power Input Jumper Settings
4.3.17 LCD Panel Voltage Select Jumper
Jumper Label: JP1
Page 86
Jumper Type: 6-pin header
Jumper Location:
Jumper Settings:
Figure 4-23
See
Table 4-26
See
The JP1 jumper sets the voltage to the LCD panel.
JP1 Description
1-2 Panel Voltage select 3.3V (Default)
3-4 Panel Voltage select 5V
5-6 Panel Voltage select 12V
Table 4-26: LCD Panel Voltage Select Jumper Settings
Page 87
ISDM Series Industrial Monitor
4.3.18 AV-5300 External (Rear Panel) Connectors
Figure 4-24 shows the AV-5300 external (rear panel) connectors. The peripheral
connectors on the back panel of the monitor can connect to external devices. The
peripheral connectors on the rear panel are:
1 x DC 12V connector
1 x DVI-D connector
1 x VGA connector
Figure 4-24: AV-5300 External (Rear Panel) Connectors
4.3.19 DC 12V Connector
CN Label: J3
CN Type: DC 12V Jack
CN Pinouts: See
CN Location:
Use the DC 12V connector to power the monitor.
PIN DESCRIPTION
1 GND
2 GND
3 DC 12V
Table 4-27
Figure 4-24
See
Table 4-27: DC 12V Connector Pinouts
Page 87
Page 88
4.3.20 VGA Connector
CN Label: J5
CN Type: D-sub 15 female connector
ISDM Series Industrial Monitor
CN Pinouts: See
CN Location:
Table 4-28 and Figure 4-25
Figure 4-24
See
Use the standard D-sub 15-pin VGA connector to connect the monitor to a system.
PIN DESCRIPTION PIN DESCRIPTION
1 Red 9 No Connect
2 Green 10 Ground
3 Blue 11 No Connect
4 No Connect 12 DDC DAT
5 Ground 13 Horizontal Synchronization
6 Ground 14 Vertical Synchronization
7 Ground 15 DDC Clock
8 Ground
Table 4-28: VGA Connector Pinouts
Page 88
Figure 4-25: VGA Connector Pinout Locations
Page 89
ISDM Series Industrial Monitor
4.3.21 DVI-D Connector
CN Label: J2
CN Type: D-sub DVI female connector
CN Pinouts: See
CN Location:
Table 4-29 and Figure 4-26
Figure 4-24
See
The 24-pin female dual link digital only DVI [Digital Visual Interface] connector is a
standard for high-speed, high-resolution digital displays. Use the DVI-D connector to
connect the LCD to a system.
PIN DESCRIPTION PIN DESCRIPTION
1 RX2- 2 RX2+
3 GND 4 NC
5 NC 6 DVI-SCL
7 DVI-SDA 8 NC
9 RX1- 10 RX1+
11 GND 12 NC
13 NC 14 DVI-5V
15 GND 16 HOT-PLUG
17 RX0- 18 RX0+
19 GND 20 NC
21 NC 22 GND
23 RXC+ 24 RXC-
Table 4-29: DVI-D Connector Pinouts
Page 89
Page 90
Figure 4-26: DVI-D Connector Pinout Locations
ISDM Series Industrial Monitor
Page 90
Page 91
ISDM Series Industrial Monitor
Chapter
Chapter
4
5
5 Installation
Page 91
Page 92
5.1 Installation Precautions
When installing the ISDM series industrial monitor, please follow the precautions listed
below:
Read the user manual: The user manual provides a complete description of
the ISDM series industrial monitor, installation instructions and configuration
options.
DANGER! Disconnect Power: Power to the monitor must be disconnected
when installing the ISDM series industrial monitor, or before any attempt is
made to access the rear panel. Electric shock and personal injury might occur
if the rear panel of the monitor is opened while the power cord is still
connected to an electrical outlet.
Qualified Personnel: The ISDM series industrial monitor must be installed
and operated only by trained and qualified personnel. Maintenance, upgrades,
ISDM Series Industrial Monitor
or repairs may only be carried out by qualified personnel who are familiar with
the associated dangers.
Mounting: Since the monitor may weigh up to 10 kg (not including a swing
arm or other accessories), please ensure at least two people assist with
mounting the monitor.
Air Circulation: Make sure there is sufficient air circulation when installing the
monitor. The monitor’s cooling vents must not be obstructed by any objects.
Blocking the vents can cause overheating of the monitor. Leave at least 5 cm
of clearance around the monitor to prevent overheating.
Grounding: The monitor should be properly grounded. The voltage feeds
must not be overloaded. Adjust the cabling and provide external overcharge
protection per the electrical values indicated on the label attached to the back
of the monitor.
Anti-static Discharge: The rear panel of the monitor must to be removed to
configure the monitor’s AD board voltage select jumper. When doing so, be
sure the monitor is disconnected from its power source and take all necessary
safety precautions to avoid electrocution and static discharge to the AD board.
Page 92
The use of a grounded wrist strap and an anti-static work pad is
recommended.
Page 93
ISDM Series Industrial Monitor
5.2 Unpacking
5.2.1 Packaging
When shipped, the ISDM series industrial monitor is wrapped in a plastic bag. Two
polystyrene ends are placed on either side of the monitor. The monitor is then placed into
a first (internal) cardboard box. This box is then sealed and placed into a second (external)
cardboard box. The second box is also sealed. A bag containing accessory items is
placed underneath the monitor, at the bottom of the internal (first) box.
5.2.2 Unpacking Procedure
To unpack the ISDM series industrial monitor, follow the steps below:
WARNING:
The front side LCD screen has a protective plastic cover stuck to the
screen. Only remove the plastic cover after the ISDM series industrial
monitor has been properly installed. This ensures the screen is protected
during the installation process.
Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
external (second) box.
Step 2: Open the external (second) box.
Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the
internal (first) box.
Step 4: Lift the monitor out of the boxes.
Step 5: Remove both polystyrene ends, one from each side.
Step 6: Pull the plastic cover off the ISDM series industrial monitor.
Page 93
Page 94
Step 7: Make sure all the components listed in the packing list are present. Step 0:
5.2.3 Packing List
All the monitors in the ISDM series are shipped with the following components:
ISDM Series Industrial Monitor
1 x ISDM-190/170/150/121/104/84 series industrial monitor.
1 x AC Power cable
1 x VGA Cable
1 x 45W AC Power Adapter (ISDM-190 / 170 / 150 / 121)
1 x 25W AC Power Adapter (ISDM-104 / 84)
5 x Replacement Round Head Screw
5 x Replacement Flat Head Screw
5 x Replacement Wire Strain Band
1 x User Manual on CDROM
1 x Power Cable for Terminal Block (Optional for M model)
1 x Touch Panel RS-232 Cable / Touch Pen / Driver CDROM (for T-R model)
1 x Touch Panel USB Cable / Touch Pen / Driver CDROM (for USB/T-R
model)
If any of these items are missing or damaged, contact the distributor or sales
representative immediately.
5.3 Pre-installation Preparation
5.3.1 Tools
Before installing the ISDM series industrial monitor, make sure the following tools are on
hand:
Philips (crosshead) screwdriver: All the retention screws on the system are
Philips screws.
Soft working mat: When the ISDM series industrial monitor is installed, the
Page 94
screen is placed on the working surface. It is therefore important to rest the
MPC indutrial workstation on a soft at that cannot damage the LCD screen on
the front of the ISDM series industrial monitor.
Page 95
ISDM Series Industrial Monitor
5.3.2 Voltage Select Jumper Settings
If the monitor comes with both 12V and 9~36V DC power connectors, the voltage select
jumper on the integrated AD board must be configured for the DC connector that is used
to power the monitor. Refer to Chapter
board.
4 for the appropriate jumper settings of each AD
NOTE:
The default voltage select jumper is configured for a 12V power source.
Do not change the jumper setting unless a 9~36V DC power connector is present
on the rear panel and is to be used as the monitor’s power source.
To properly set the voltage select jumper, the following steps must be completed:
Step 1: Use a screwdriver to remove all the screws holding the rear panel to the monitor.
Step 2: Remove the rear panel.
Step 3: Locate the voltage select jumper. (See Chapter
4)
Step 4: Use the jumper(s) to set the correct voltage input. (See Chapter
Step 5: Replace the rear panel.
Step 6: Replace all removed screws.Step 0:
4)
Page 95
Page 96
5.4 Connectors
Table 5-1 lists the rear panel connectors for the ISDM series industrial monitors.
ISDM Series Industrial Monitor
VGA
DVI-D
Power (12V
Jack)
Touch Panel
Power (9~36V)
(Optional)
Table 5-1: Rear Panel Connectors
ISDM-084G ISDM-104G ISDM-121G ISDM-150G ISDM-170G ISDM-190G
Yes Ye s Yes Ye s Yes Ye s
- - Ye s Ye s Yes Ye s
Yes Ye s Yes Ye s Yes Ye s
Yes Ye s Yes Ye s Yes Ye s
Yes Ye s Yes Ye s Yes Ye s
Page 96
Page 97
ISDM Series Industrial Monitor
5.4.1 Rear Panel Connectors Overview
Figure 5-1: Monitor Rear Panel Connections
Figure 5-1 shows all the possible rear panel connectors for the ISDM series industrial
monitor. Refer to
The following sections fully describe the rear panel connectors for the ISDM series
industrial monitor.
Table 5-1 for a list of the monitors and their corresponding connectors.
5.4.2 VGA Connector
Use the rear panel standard 15-pin female VGA connector to connect the monitor to the
system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION
1 RED 6 GROUND 11 NC
2 GREEN 7 GROUND 12 DDCDAT
3 BLUE 8 GROUND 13 HSYNC
4 NC 9 NC 14 VSYNC
5 GROUND 10 GROUND 15 DDCCLK
Table 5-2: VGA Connector Pinouts
Page 97
Page 98
Figure 5-2: VGA Connector
5.4.3 DVI-D Connector
Use the rear panel standard 24-pin female DVI-D connector to connect the monitor to the
system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION
1 TMDS Data2- 9 TMDS Data1- 17 TMDS Data0-
2 TMDS Data2+ 10 TMDS Data1+ 18 TMDSData0+
ISDM Series Industrial Monitor
3 TMDS Data2/4 Shield 11 TMDS Data1/3 Shield 19 TMDS Data0/5 Shield
4 TMDS Data4- 12 TMDS Data3- 20 TMDS Data5-
5 TMDS Data4+ 13 TMDS Data3+ 21 TMDS Data5+
6 DDC Clock [SCL] 14 +5 V Power 22 TMDS Clock Shield
7 DDC Data [SDA] 15 Ground (for +5 V) 23 TMDS Clock +
8 Analog vertical sync 16 Hot Plug Detect 24 TMDS Clock -
Table 5-3: DVI-D Connector Pinouts
Figure 5-3: DVI-D Connector
5.4.4 12V Power Connector
Page 98
Use the rear panel +12V DC jack to connect the monitor to a power source.
Page 99
ISDM Series Industrial Monitor
Figure 5-4: 12V Power Connector
5.4.5 Optional DC Power Connector
Use the rear panel 3-pin terminal block DC power connector to connect the monitor to a
DC power source.
Figure 5-5: DC Power Connector
5.4.6 Optional RS-232 Touch Panel Connector
Use the rear panel standard RS-232 DB-9 female touch panel connector to connect the
monitor to the system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION
1 DCD1 6 CTS1
2 DSR1 7 DTR1
3 RX1 8 RI1
4 RTS1 9 GND
Page 99
Page 100
5 TX1
Table 5-4: Optional RS-232 Touch Panel Connector Pinouts
Figure 5-6: Optional RS-232 Touch Panel Connector
5.4.7 Optional USB Touch Panel Connector
ISDM Series Industrial Monitor
Use the rear panel standard USB touch panel connector to connect the monitor to the
system graphics interface.
PIN DESCRIPTION PIN DESCRIPTION
1 DCD1 6 CTS1
2 DSR1 7 DTR1
3 RX1 8 RI1
4 RTS1 9 GND
5 TX1
Table 5-5: Optional USB Touch Panel Connector Pinouts
Figure 5-7: Optional USB Touch Panel Connector
Page 100
Loading...