Page 1
1
Half-size pure ISA CPU card with on-board AMD Geode™ LX
600@0.7W Processor at FSB 366MHz, 128KB L2 cache,
128MB memory on board include VGA, LAN, USB2.0, CF,
COM, LPT and Audio, RoHS
IOWA- LX-600
Quick Installation Guide
Version 1.0
Mar. 14, 2011
Package List
IOWA-LX-600 package includes the following items:
l 1 x IOWA-LX-600 Single Board Computer
l 1 x USB Cable
l 1 x IDE Flat Cable
l 1 x KB/MS Y Cable
l 1 x Audio Cable
l 1 x Mini Jumper Pack
l 1 x Utility CD (within manual)
l 1 x QIG (Quick Installation Guide)
l 1 x One Key Recovery CD
©2011 Copyright by IEI Technology corp.
All rights reserved.
Page 2
2
Specifications
l CPU:
On-board AMD Geode™ LX 600@ processor at FSB 366MHz,
128KB L2 cache
l System chipset: AMD Geode™ CS5536
l BIOS: Award BIOS
l System memory :
On-board 128MB (max.) 200/266MHz DDR SDRAM supported.
One 204 -pin 512MB (max.) 200/266MHz DDR SO-DIMM
supported.
l Ethernet:
10/100Mbps Realtek RTL8100C Ethernet controller
l Super IO: Winbond W83627EHG
l I/O Interface:
2 x RS -232
1 x RS -422/485
1 x IDE
1 x FDD
1 x LPT
2 x SATA (Optional for IOWA-LX-600S-R10)
1 x CF type II
4 x USB 2.0 (by pin header)
1 x PS/2 KB/MS
l Expansion:
ISA bus supported via golden finger
l Digital I/O: 8-bit digital I/O, 4-bit input / 4-bit output
l Display Output:
Single HD VOP 2.0 output
1920x1440 CRT output
1600x1200 TFT output
l Graphic Engine:
VGA integrated in the AMD Geode™ LX 600
l Audio: Realtek ALC203 with AC'97 codec
Page 3
3
l Watchdog Timer:
Software programmable supports 1~ 255sec. System reset
l Power supply: 5V/12V via ISA bus , AT/ATX mode supported
l Power Consumption:
5V@1.51A, 5VSb@0.09 (On -board AMD Geode™ LX 600 CPU
366MHz with 200MHz DDR 128MB On-board Memory and
333MHz DDR 512MB Memory)
l Temperature: Operation: -10°C~60°C
l Humidity: Operation: 5%~95% non-condensing
l Dimension: 185mm x 122mm
Ordering Information
l IOWA-LX-600-R10：Half-size pure ISA CPU card with on -board AMD
Geode™ LX 600 processor at FSB 366MHz, 128KB L2 cache, 128MB
memory on board include VGA, LAN, USB 2.0, COM, CF, LPT and
Audio, RoHs
l IOWA-LX-600S-R10：Half-size pure ISA CPU card with on-board AMD
Geode™ LX 600 processor at FSB 366MHz, 128KB L2 cache, 128MB
memory on board include VGA, LAN, USB 2.0, SATA, COM, CF, LPT
and Audio, RoHs
l 32000-062800-RS：SATA Cable
l 32200-000017-RS：FDD Cable
l 19800-000400-100-RS：LPT Cable
l 19800-000058-RS：RS-232/422/485 Cable
Page 4
4
Jumpers Setting and Connectors
LABEL
FUNCTION
JP2 Use AT & ATX Power Select jumper
JP3 COM3 Signal jumper Setting
JP4 Serial port’s (CN21 & CN18) RI Signal Select
JP5 Flat Panel TTL (CN10) power using select
JP6 Flat Panel TTL (CN10) Clock using select
CN1 External – VCC Power Connector
CN2 Power Connector
CN3 PS-ON Connector
CN6 PWR & RST Button and Indicators panel
CN7 Inverter Connector
CN8 CPU Fan Connector
CN9 Floppy Connector
CN10 TFT LCD Connector
CN11 Primary IDE Connector (40pin 2.54mm)
CN12 Internal USB1 2.0 Connector (2 ports)
CN13 Internal USB2 2.0 Connector (2 ports)
CN14 Battery socket
CN15 IrDA Connector
CN16 10-pin Digital I/O Connector
CN17 Parallel Port Connector
CN18 Internal Serial Port (COM2/3) Connector
CN19 Audio Connector (Line out, Line in & MIC in)
CN20 Audio CD In Connector
CN21 External Serial Port (COM1) Connector
CN22 LAN Connector (RJ-45)
CN23 DB-15pin VGA Connector
CN24 Keyboard / Mouse Connector
CN25 6-pin Pin Header Keyboard/Mouse Connector
CN26 Serial ATA Connector
CN27 Serial ATA Connector
CN29 SDRAM DDR SO-DIMM socket
Page 5
5
JP2: Use AT & ATX Power Select jumper
PIN NO. DESCRIPTION
Short 1 - 2 Use AT Power
Open 1 - 2 Use ATX Power
JP3: COM3 Signal jumper Setting
PIN NO. DESCRIPTION
Short 1 - 2 RS-422
Short 2 - 3 RS-485
JP4: Serial port’s CN21 Pin9 (CN18 Pin8) RI Signal Select
CONNECTOR
CN21 CN18
DESCRIPTION
Short 1 - 3 Short 2 - 4 12 Voltage output
Short 3 - 5
Short 5 - 7
Short 4 - 6
Short 6 - 8
5 Voltage output
Short 7 - 9 Short 8 - 10 Normal RI Function
JP5: Flat Panel TTL (CN10)
power using select
PIN NO. DESCRIPTION
Short 1 - 2 + 3.3V
Short 2 - 3 + 5V
JP6: Flat Panel TTL (CN10) Clock using select
PIN NO. DESCRIPTION
Short 1 – 2
Default
FPCLK
Short 2 - 3 FPCLK#
Page 6
6
CN19: Audio Connector (Line out, Line in & MIC in)
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 Line Out (Right)
2 Line In (Right)
3 GROUND 4 GROUND
5 Line Out (Left) 6 Line In (Left)
7 GROUND 8 GROUND
9 MIC1 In 10 MIC2 In
CN11: Primary IDE Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RESET# 2 GROUND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GROUND 20 N/C
21 DRQ 22 GROUND
23 IOW# 24 GROUND
25 IOR# 26 GROUND
27 CHRDY 28 (PULL LOW TO GND)
29 DACK# 30 GROUND
31 INTERRUPT 32 N/C
33 SA1 34 N/C
35 SA0 36 SA2
37 HDC CS0# 38 HDC CS1#
39 HDD ACTIVE#
40 GROUND
CN20: Audio CD In Connector
PIN NO. DESCRIPTION
1 CD SIGNAL (Left)
2 GROUND
3 GROUND
4 CD SIGNAL (Right)
Page 7
7
CN8: CPU Fan
PIN NO. DESCRIPTION
1 Ground
2 +5V
3 Rotation Signal
CN17: Parallel Port Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 STROBE# 2 AUTO FORM FEED #
3 DATA 0 4 RROR#
5 DATA 1 6 INITIALIZE
7 DATA 2 8 PRINTER SELECT LN#
9 DATA 3 10 GROUND
11 DATA 4 12 GROUND
13 DATA 5 14 GROUND
15 DATA 6 16 GROUND
17 DATA 7 18 GROUND
19 ACKNOWLEDGE
20 GROUND
21 BUSY 22 GROUND
23 PAPER EMPTY 24 GROUND
25 PRINTER SELECT
26 N/C
CN15: IrDA Connector
PIN NO. DESCRIPTION
1 VCC
2 N/C
3 IR-RX
4 Ground
5 IR-TX
CN13: Internal USB 2.0 Connector (2 ports)
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 2 GROUND
3 DATA3- 4 DATA4+
5 DATA3+ 6 DATA47 GROUND 8 VCC
CN12: Internal USB 2.0 Connector (2 ports)
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCC 2 GROUND
3 DATA1- 4 DATA2+
5 DATA1+ 6 DATA27 GROUND 8 VCC
Page 8
8
CN24: KB/MS Connector
PIN NO. DESCRIPTION
1 KEYBOARD DATA
2 MOUSE DATA
3 GROUND
4 +5V
5 KEYBOARD CLOCK
6 MOUSE CLOCK
CN21: External Serial Port Connector
PIN NO. DESCRIPTION
1 DATA CARRIER DETECT (DCD)
2 RECEIVE DATA (RXD)
3 TRANSMIT DATA (TXD )
4 DATA TERMINAL READY (DTR)
5 GROUND (GND)
6 DATA SET READY (DSR)
7 REQUEST TO SEND (RTS)
8 CLEAR TO SEND (CTS)
9 RING INDICATOR (RI)
CN25: 6-pin KB/MS Connector
PIN NO. DESCRIPTION
1 +5V
2 MOUSE DATA
3 MOUSE CLOCK
4 KEYBOARD DATA
5 KEYBOARD CLOCK
6 GROUND
CN18: Internal Serial Port Connector
PIN NO. DESCRIPTION
1 DATA CARRIER DETECT (DCD)
2 DATA SET READY (DSR)
3 RECEIVE DATA (RXD)
4 REQUEST TO SEND (RTS)
5 TRANSMIT DATA (TXD)
6 CLEAR TO SEND (CTS)
7 DATA TERMINAL READY (DTR)
8 RING INDICATOR (RI)
9 GROUND (GND)
10 GROUND (GND)
Page 9
9
CN2: Power Connector
PIN NO. DESCRIPTION
1 +5V
2 GND
3 GND
4 +12V
CN16: 10 -pin Digital I/O
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GROUND 2 +5V
3 OUTPUT 0 4 OUTPUT1
5 OUTPUT 2 6 OUTPUT3
7 INPUT 0 8 INPUT 1
9 INPUT 2 10 INPUT 3
CN6: PWR & RST Button and Indicators Panel
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 PWRBTN 2 +5V
3 GROUND 4 GROUND
5 +5V 6 RESET
7 HDDLED- 8 GROUND
CN23: DB-15pin VGA Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 RED 2 GREEN
3 BLUE 4 N/C
5 GROUND 6 GROUND
7 GROUND 8 GROUND
9 N/C 10 GROUND
11 N/C 12 DDC DAT
13 HSYNC 14 VSYNC
15 DDCCLK
CN3: PS-ON Connector
PIN NO. DESCRIPTION
1 Ground
2 PS-ON
3 +5V Standby
Page 10
10
CN1:External –VCC Power
PIN NO. DESCRIPTION
1 -5V
2 GROUND
3 -12V
CN18: RS -422/485
PIN NO. DESCRIPTION
11 TX+
12 TX-
13 RX+
14 RX-
CN22: LAN Connectors (RJ-45)
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 TX+ 8 N/C
2 GROUND 9 ACT_LED3 TX- 10 ACT_LED+
4 RX+ 11 LINK_LED 5 GROUNG 12 LINK_LED+
6 RX- 13 GROUND
7 N/C 14 GROUND
CN10: TFT LCD Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 VCD_VCC 2 VCD_VCC
3 GROUND 4 GROUND
5 VCD_VCC 6 VCD_VCC
7 I_SDATA 8 GROUND
9 TFT_B0 10 TFT_B1
11 TFT_B2 12 TFT_B3
13 TFT_B4 14 TFT_B5
15 TFT_B6 16 TFT_B7
17 TFT_G0 18 TFT_G1
19 TFT_G2 20 TFT_G3
21 TFT_G4 22 TFT_G5
23 TFT_G6 24 TFT_G7
25 TFT_R0 26 TFT_R1
27 TFT_R2 28 TFT_R3
29 TFT_R4 30 TFT_R5
31 TFT_R6 32 TFT_R7
33 GROUND 34 GROUND
35 FPCLK 36 VSYNC
37 LCD_EN 38 HSYNC
39 I_SCLK 40 DISPEN
Page 11
11
CN26 & CN27 :
Serial ATA
PIN NO. DESCRIPTION
1 GND
2 S_TXP
3 S_TXN
4 GND
5 S_RXN
6 S_RXP
7 GND
CN9: Floppy Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GROUND 2 DRVDEN0
3 GROUND 4 N/C
5 GROUND 6 N/C
7 GROUND 8 INDEX#
9 GROUND 10 MOT0#-
11 GROUND 12 N/C
13 GROUND 14 DSA#15 GROUND 16 N/C
17 GROUND 18 DIR#
19 GROUND 20 STEP#
21 GROUND 22 WDATA#
23 GROUND 24 WGATE#
25 GROUND 26 TRK0#
27 GROUND 28 WP#
29 N/C 30 RDATA#
31 GROUND 32 HDSEL#
33 N/C 34 DSKCHG#
CN7: Inverter Power
PIN NO. DESCRIPTION
1 Ground
2 Ground
3 +12V
4 Ground
5 LCD Enable
Page 12
12
Board Layout: Jumper and Connector Locations
( Unit:mm）
Loading...